DENVER CRL-310 ENGLISH FUNCTION AND CONTROLS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21.
LOCATION OF REMOTE CONTROLS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. ON/OFF / ALARM OFF SOURCE / DISPLAY OFF SNOOZE / SLEEP / DIMMER LIGHT ON/OFF MOOD LIGHT ON / OFF TEMPERATURE / C-F << / TUNE - / BETWEEN DISPLAY CONTENTS ON-OFF ALARM 1 CONTROL VOLUME DOWN ALARM 2 CONTROL >> / TUNE + / NAP / DST TIME SET / MEMORY / MEMORY+ YEAR/MONTH-DAY VOLUME UP NATURAL SOUND SELECT MOOD LIGHT SELECT (To turn the unit RGB color changing or to stop the MOOD LIGHT color changing.) 17.
LED DISPLAY MODE TIME Indicator PM Indicator AUX Indicator ALARM 1 Indicator FM Indicator ALARM 2 Indicator MONTH Indicator DAY Indicator TEMPERATURE Indicator Get started • Select a proper place for the device such as a dry, and even non slip area where you can easily operate the device.
remote control button (7), (11) for faster scanning backward or forward. Tap the unit button (7) or the remote control button (12) to confirm. 4. Repeat steps #2 to #3 to adjust the month, day, time format, current hour and finally current minute in the same way.
Display on/off function • In standby mode, press and hold unit SOURCE button (9) or the remote control SOURCE button (2) for 3 seconds. “ON” appears on the display (2). • After 15 seconds, the display (2) turns off. • Press any button to turn the display (2) on for another 15 seconds. • To deactivate the display on/off function, press and hold unit SOURCE button (9) or the remote control SOURCE button (2) for 3 seconds. “OFF” appears on the display (2). Reading light function 1.
2. The LED DISPLAY will show the radio frequency for about 5 seconds and then revert to normal time display. AUTOMATIC SEARCH FOR RADIO STATIONS To automatically search for stations with strong signals, press and hold the main unit button (10) and (11) or the remote control button (7) and (11) until the frequency readout on the display begins to scan. Release the button. The tuner will stop on the first strong station it finds. MANUAL SEARCH FOR RADIO STATIONS 1.
the unit button (7) or the remote control button (12) repeatedly until you reach the desired preset number/radio station. ALARM SETTING You can set two alarm times. 6 different alarm options are available: Radio + Light / Radio / Buzzer + Light / Buzzer / Natural sound + Light / Natural sound. The setting sequence for AL1 and AL2 is as follows: In radio off mode, Press the main unit alarm set buttons (12) and (13) or the remote control buttons (8) and (10) to show the alarm time.
SETTING THE ALARM 2 (NATURAL SOUND) Normal Time → AL 2 Hour → AL 2 Minute → AL 2 weekday → AL 2 beeper → AL 2 radio →AL 2 natural sound →(Use the unit buttons (10) and (11) or the remote control buttons (7) and (11) to select the desired natural sound) →AL 2 final natural sound volume →AL 2 Light → AL 2 Light intensity → Normal Time. Proceed as follows: 1. In standby mode, Press the unit Alarm1 button (12) or the remote control button (8). The currently set alarm time is shown. 2.
• NS (natural sound): As soon as your set alarm time is shown, the natural sound switches on. The natural sound is played. The volume increases slowly to the set volume. The volume cannot be adjusted. NOTE: • The alarm function turns off automatically after 30 minutes until the next day. 7a. If you want to be awakened by a radio station, select the maximum alarm volume using the unit (10) and (11) buttons or the remote control (7) and (11) buttons. 8.
SNOOZE FUNCTION (MAIN UNIT) When the alarm source is sounding, press the unit any buttons (except on/off button (14)) or the remote control SNOOZE button (3) to suspend the alarm and activate the snooze function. The Alarm will temporarily stop and sound again 9 minutes later but the AL1 (or AL2) indicator will keep flashing. Notes: This manual snooze operation can be repeated again and again. To turn off the snooze function, Press the main unit on/off button (14) or the remote control on/off button (1).
Note: When using the NAP alarm the wake up light function is inactive. NATURAL SOUND 1. In standby mode, tap the unit ON-OFF button (14) or the remote control ON-OFF button (1) to turn the unit ‘On’. 2. Press the unit button (9) or the remote control button (2) to switch to natural sound mode. 3. Use the main unit buttons (10) and (11) or the remote control button (15) to select the desired natural sound.
ALTERNATE DISPLAY BETWEEN TIME AND TEMPERATURE MONTH-DATE DISPLAY 1. In radio off mode, press and hold the unit button (10) or the remote control button (7) for about 3 seconds until “ON” appears in the LED DISPLAY. 2.
WARNING 1. No naked flame sources, such as lighted candles, should be placed on the apparatus. 2. Do not place the product in closed bookcases or racks without proper ventilation. 3. The mains plug is used as the disconnect device, the disconnect device shall remain readily operable. 4. The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, tablecloths, curtains, etc. 5.
DISPOSAL OF YOUR OLD APPLIANCE OR BATTERY: 1. When this crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the European Directive. 2. All electrical and electronic products including battery should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S www.denver-electrionics.com Electric and electronic equipment and included batteries contains materials, components and substances that can be hazardous to your health and the environment, if the waste material (discarded electric and electronic equipment and batteries) is not handled correctly. Electric and electronic equipment and batteries is marked with the crossed out trash can symbol, seen below.
