USER MANUAL 19LEDCACI LED TV with DVB S2 CA CI, DVB T CI, DVD Loader and Sound Bar Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference (All pictures used in this manual are only for illustration purpose. Those pictures may be different from the actual TV unit.
Important Safety Instructions: The Lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un-insulated "DANGEROUS VOLTAGE " within the product's enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.
Important Safety Instructions Continued Heat The Product should be situated away from heat source such as radiators, heat registers, stoves or other products (including amplifiers) that produce heat. Object and Liquid Entry Unit should not be exposed to liquids of any kind. Don't place the unit on an uneven surface. Make sure it is at least 6inches from the wall. Don't step or put heavy materials on top of the unit. Do not place unit in confined spaces such as a bookcase. DO NOT use this product near water.
Important Safety Instructions Continued Power Cord Protection Protect the power cord from being walked on or pinched, particularly at plugs, outlets, and the point where they exit from the unit. If the mains plug should fails to fit, contact your electrician to replace your obsolete outlet. DO NOT defeat the safety purpose of the polarized plug. Power Sources This product should be operated only from the type of power source indicated on the rear panel.
If the product has been exposed to rain or water. If the product does not operate normally after following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper Adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. If the product has been dropped or damaged in any way.
CONTENT: Page 1. Introduction 9 1.1 Product description 9 1.2 Product features 9 1.3 Package contents 10 2. System Set up 11 2.1 Front Panel Touchpad & Remote Control Function 11 2.2 Remote Control 12 2.2.1 Remote Control Battery Installation / Removal 14 2.2.2 Remote Control Operating Instruction 14 2.3 Connectivity TV Set 15 3. First Time Installation 16 3.1 Basic Operation 16 4. DVB-S2 CACI Satellite receiver Modus 16 4.1 Use of the USB port of the DVB-S2 receiver 16 4.
.3 Sound Menu 25 7.3.1 Sound Modus 25 7.3.2 Treble 25 7.3.3 Bass 25 7.3.4 Balance 26 7.3.5 Auto Volume 26 7.3.6 Surround Sound 26 7.3.7 AD Switch 26 7.3.8 EQ (Equalizer) 26 7.4 Time Menu 27 7.4.1 Clock 27 7.4.2 Time Zone 27 7.4.3 Sleep Timer 27 7.4.4 Auto Standby 27 7.4.5 OSD Timer 28 ` 7.5 Lock Menu 28 7.5.1 Lock System 28 7.5.2 Password setting 29 7.5.3 Block Program 29 7.5.4 Parental Lock 30 7.5.5 Key Lock 30 7.6 Set up Menu 30 7.6.
9.1 Picture Menu 34 9.2 Sound Menu 34 9.3 Time Menu 34 9.4 Parental lock 34 9.5 Set up Menu 34 10.Media OSD Operation 35 10.1Photo Menu 35 10.2 Music Menu 36 10.3 Movie Menu 37 10.4 Text Menu 38 11. DVD Operation 39 11.1 Basic Operation 39 11.2 DVD settings / DVD menu settings 39 11.3 DVD Picture Menu 39 11.4 Sound Menu 41 11.5 Time Menu 41 11.6 Parental Menu 41 11.7 Set up Menu 41 12.Reference 42 12.1 Screen cleaning 42 13.
Powered by SD Electronics 8
1. INTRODUCTION Product Description Thank you for choosing the DENSON 19LEDCACI TFT/LED Colour TV / HD Satellite Receiver / DVB-T Receiver / DVD / Monitor and for your continued support and use of our products. The product combines the features of a TV / DVB-S-S2 HD Satellite receiver / DVB-T H.264 MPEG2 receiver / DVD Player and PC Monitor with a THIN FILM TRANSISTOR liquid crystal A-grade display (TFT-LED).This new generation of TFT-LED incorporates a high quality display in a lightweight module.
Package Contents Please check the Package to make sure it contains the following items: TFT LCD Remote Control EU Power Cord ADAPTER THIN & FLEXIBLE 50cm coax cable with mounted 2 x Male F-connectors and 1 x Female/Female Fconn. Adapter UNIVERSAL AUTO CIGARETTE LIGTHER PLUG LINE QUICK USER INSTALLATIO MANUAL N GUIDE QUICK INSTALLATION GUIDE USER MANUAL (All pictures used in this manual are only for illustration purposes. Those pictures may be different from the actual.) 2.
2.1.Front Panel Touchpad & Remote Control Function Item Function Discription 1 IR Remote IR Sensor (Receives IR signal from remote Control) 2 LED Red - Stand by, Green- Operating 3 POWER Turn on/off TV 4 SOURCE Call out the input source selection interface. 6 MENU Display the main menu on screen; go to the previous level of OSD. 6 - CH + Decrease TV channel/ Increase TV channel. 7 - VOL+ Decrease volume; Increase volume;. 8 ■ DVD mode STOP. 9 ►II DVD mode Play/Pause.
2.2 Remote Control： ： 1 POWER: Standby mode turn on/off. 2 (Mute): Turn volume off/on. 3 SLEEP: To setup power-off timer. ZOOM: to select the screen display aspect 4 ratio. LANG/AUDIO: To select language and audio 5 channel for ATV and DTV TV/RADIO: Switch between TV and radio 6 channels in DTV mode. NUMBER BUTTONS: Press 0-9 select a TV channel directly when you are watching TV. 7 The channels change after 2 seconds. To enter page number in Teletext mode. 8 -/-- : No function.
31 ►►: Fast forward for USB media mode and DVD mode. 32 I◄◄: To playback previous chapter for USB media mode and DVD mode. 33 34 ►►I: To advance forward to the next chapter for USB media mode and DVD mode. ►II: Press to play or pause for USB media mode and DVD mode. ■：In USB mode and DVD mode Stop. 35 ● : Recorder at DVB-T mode. 36 EJECT: In DVD mode eject disc. RED Code: Use for Teletext/OSD menu red 37 color coded function.. PROG： ：In DVD mode display the program.
2.2.1. Remote Control Battery Installation / Removal CAUTION !! Avoid damaging the Remote Control by NOT: Applying excessive pressure when pressing buttons Exposing to extreme Low or High temperatures Exposing to excessive Moisture Mishandling to Dropping 2.2.2. Remote Control Operating Instruction: The Remote Control Transmission consists of an Infrared (IR) Signal. Make sure the line-of-sight between Remote Control and clear of objects that could interfere with the remote IR signal.
2.3. Connectivity TV SET: Right Side: Linkerkant: Left Side: 1. 2. 3. 4. 5.
3. First Time Installation After you have installed the satellite Dish or DVB-T antenna you switch the TV set On with the ON/OFF switch at the right side of the TV set. Press Power button on the remote control. The Power indicator instantaneously changes from red to green. 3.1 Basic Operation: − Press LCD-MENU button to display the MAIN OSD MENU; − Press ◄ / ► button to switch through the different OSD menu, e.g. Channel, Picture, Sound, Time, Lock, Setup Menu.
1. Play Mode Press the GREEN button to set the play mode. It include the Loop, Slide Show Interval and Photo View Mode options. 4.2.3. PVR Setting Press the BLUE button to enter the PVR Setting menu. In this menu, you can set the options of Record Partition, Record Mode, Record Type, Record Time,Auto Timeshift, Timeshift Buffer Size, Timeshift Need Save and Play Start Pos 4.2.4. Play Files 1. Music 1) Press the VOL+/VOL- to highlight the Music.
3. Movie 1) Press the VOL+/VOL- to highlight the Movie. 2) Press the CH+/CH- to change the folder or file and press the OK button to open the folder or play the movie file. It supports *.3GP, *.AVI,*.MKV, *.MP4, *.MOV, *.MPG, *.TS, *.M2TS, *.DAT, *.VOB format movie files. OK: View play list or play the highlighted file in the play list. : Play the file. PAUSE/||:Pause. ■: Stop playing file. : Fast rewind. : Fast forward. I : Play the previous item. I: Play the next item.
and press the Red button to mark it, then move it to the destination press OK to confirm, then you can move the marked file to destination. 4) Press the GREEN button set the Play Mode. 5) Press Yellow key to delete highlighted file from Play List. 6) Press the BLUE button to delete all files from Play list. 4.4. USB Software Upgrade of the DVB-S2 receiver: 4.4.1.
After you selected the SOURCE, the First step is to set the OSD language required. Push the MENU button on the RCU or TV set to enter the MAIN MENU. In the Main Menu you can use the ◄ / ► button to select one of the next sub Menu’s > CHANNEL, PICTURE, SOUND, TIME, LOCK and SET UP. OSD Language setting you find as sub menu under SET UP. Select with the ◄ / ► button SET UP and push the OK button. Next SET-UP Menu will, be shown on screen >: Select the OSD LANGUAGE with the ▼ / ▲ button and push OK.
To view DVB-T digital TV, you have to push the SOURCE button on the RCU and select DTV with the ▼ / ▲ buttons and then push OK button to confirm. ( DTV = Digital TV > DVB-T is DTV ) 7.1 Channel Menu: Press LCD-MENU button to display the MAIN OSD MENU. Press ◄ / ► button to select the Channel Menu. Press ▼ / ▲ button to enter the sub menu entries. 7.1.1. Auto Tuning: − Select Auto Tuning then press OK or ► button to start auto tuning process.
− − − Select the Current CH for the manual tuned channel to be stored in. Select the TV colour system and sound system. Select whether Auto Frequency Control (AFC) to be on/off. AFC will do minor adjustment for shifted frequency in order to get better tuned picture. − Press ► button while Search is selected to start the manual tuning process. 7.1.4. Programme Edit: − Select Programme Edit then press OK or ► button to enter ATV programme tuning interface.
− Select CI Information then press OK or ► button to enter CI Information interface. − Display the Common Interface card information. Note: Not available in ATV mode. 7.2. Picture Menu: 1. Press LCD-MENU button to display the MAIN OSD MENU. Press ◄ / ► button to select the Picture Menu. Press ▼ / ▲ button to select the option that you want to adjust in the Picture menu, then press OK button or ► button to enter to the sub menu. 7.2..1.
− Select Brightness then press OK or ► button to enter brightness sub menu. − Press ◄ / ► button to make the adjustment. − Press OK or LCD MENU button to confirm adjustment and go back to previous menu. Note: Brightness only available for adjustment when in Personal picture mode. 7.2.4. Colour: − Select Colour then press OK or ► button to enter colour sub menu. − Press ◄ / ► button to make the adjustment. − Press OK or LCD MENU button to confirm adjustment and go back to previous menu.
7.2.9. Dynamic CR: − Dynamic contrast ratio function. − Press ► button to select ON/OFF for this function. − This feature allows backlight adjustment to automatically control the black and white level of display. 7.3. Sound Menu: 1. Press LCD-MENU button to display the MAIN OSD MENU. Press ◄ / ► button to select the Sound Menu. Press ▼ / ▲ button to select the option that you want to adjust in the Sound menu, then press OK button or ► button to enter to the sub menu. 7.3.1.
− Select Bass then press OK or ► button to enter Bass sub menu. − Press ◄ / ► button to make the adjustment. − Press OK or LCD MENU button to confirm adjustment and go back to previous menu. 7.3.4. Balance: − Select Balance then press OK or ► button to enter Balance sub menu. − Press ◄ / ► button to make the adjustment. − Press OK or LCD MENU button to confirm adjustment and go back to previous menu. 7.3.5. Auto Volume: − Select Auto Volume then press OK or ► button to turn this feature On/Off.
1. Press LCD-MENU button to display the MAIN OSD MENU. Press ◄ / ► button to select the Time Menu. Press ▼ / ▲ button to select the option that you want to adjust in the Time menu, then press OK button or ► button to enter to the sub menu. 7.4.1. Clock: − Display the current system time. Note: Not available in ATV mode. 7.4.2. Time Zone: − Select Time Zone then press OK or ► button to enter Time Zone sub menu. − Press ◄ / ► / ▼ / ▲ button to select the time zone you are currently in.
− Press OK button to confirm selection. Press LCD MENU button to return to previous menu without changes. − Press EXIT button to exit the OSD completely. − Auto Standby function allows TV to go into standby mode if the TV is not operated at all for the duration. i.e. no keypad and remote button is pressed during the interval. 7.4.5. OSD Timer: − Select OSD Timer then press OK or ► button to enter OSD Timer sub menu. − Press ▼ / ▲ button to select the OSD timer you desire.
− The default password is “0000”. − After correct password is entered, the “Block program”, Parental Guidance” and “Key Lock” function will be available for setting. 7.4.2. Set Password: − Select Set Password then press OK or ► button to enter change password interface as seen below. − Enter old password, if the old password is incorrect, the password will not be allowed to be modified. − Enter new password. − Enter new password again at.
− Blocked channel can only be watched when correct password is inserted. 7.5.4. Parental Guidance: − Select Parental Guidance then press OK or ► button to enter Parental Guidance sub menu. − Press ▼ / ▲ button to select the age requirement you desire. You can select from: o − Off/4/5/6/7/8/9/10/11/12/13/14/15/16/17/18 Press OK button to confirm selection. Press LCD MENU button to return to previous menu without changes. − Press EXIT button to exit the OSD completely. 7.5.5.
− Press OK button to confirm selection. Press LCD MENU button to return to previous menu without changes. − 7.6.3. Press EXIT button to exit the OSD completely. Impaired: − Select Hearing Impaired then press OK or ► button to enable/disable the Hearing Impaired function. − Hearing Impaired function will only be usable provided the TV program broadcasted supports this feature. Note: Not available in ATV mode. 7.6.4.
7.6.5. Aspect Ratio: − Select Aspect Ratio then press OK or ► button to enter Aspect Ratio sub menu. − Press ▼ / ▲ button to select the aspect ratio display you desire. You can select from: o − Auto / 4:3 / 16:9 / Zoom1 / Zoom2 Press OK button to confirm selection. Press LCD MENU button to return to previous menu without changes. − Press EXIT button to exit the OSD completely. 7.6.6. Blue Screen: − Select Blue Screen then press OK or ► button to enable/disable the Blue Screen function.
8. PC Mode OSD Operation: 8.1. Screen Menu: Press LCD-MENU button to display the MAIN OSD MENU. Press ◄ / ► button to select the Screen Menu. Press ▼ / ▲ button to enter the sub menu entries. 8.1.1. Auto Adjust: − Select Auto Adjust then press OK or ► button to auto adjust the PC display. 8.1.2. H-Offset: − Select H-Offset then press OK or ► button to move the PC display horizontally (left/right). 8.1.3. V-Offset: − Select V-Offset then press OK or ► button to move the PC display vertically (up/down).
8.3. Sound Menu: − Same with ATV mode. 8.4. Time Menu: − Same with ATV mode. 8.5. Lock Menu: − Same with ATV mode with the exception of Block Program and Parental Guidance function are unavailable. 8.6. Setup Menu: − Same with ATV mode with the exception of TT Language, Hearing Impaired and PVR File System functions are unavailable. 9.0 AV/SCART/HDMI OSD Operation: 9.1. Picture Menu: − Same with ATV/DTV mode. 9.2. Sound Menu: − Same with ATV mode. 9.3. Time Menu: − Same with ATV mode. 9.4.
10. Media OSD Operation: Plug in the USB drive with the media file into the USB port before operating the Media interface. Select the source as MEDIA. Press ◄ / ► button to select the media format between Photo, Music, Movie and Text. Press OK button to enter the selected media entries. 10.1. Photo Menu: − Select the drive/partition of your USB/hard disk. Normally it is C: drive. − Select the folder where your Photo files are located.
Play - Start the slide show Prev. - Go to previous photo. Next. - Go to next photo. Stop - Stop the slide show and go back to thumbnail view mode. Repeat - RepeatAll: Repeat all the photos in slide show again RepeatNone: No repeat, slide show go back to thumbnail mode after showing all the photos. Music - Repeat 1: Continuously showing current photo, repeating itself. - Play the music in the background. Only music file placed in the same directory with the photo will be played.
FB. - Fast backward, speed of 2x, 4x, 8x and 16x. FF. - Fast forward, speed of 2x, 4x, 8x and 16x. Prev. - Go to previous song. Next. - Go to next song. Stop - Stop the slide show and go back to thumbnail view mode. Repeat - RepeatAll: Repeat all the songs in the playlist/folder. RepeatNone: No repeat, will stop after all the songs in the playlist are played. - Repeat 1: Continuously playing current song, repeating itself.
RepeatNone: No repeat, will stop after all the movies in the playlist are played. - Repeat 1: Continuously playing current movie, repeating itself. Set A/B - Set the movie to repeatedly playing section A to section B. Playlist - Show the playlist of the movies folder. You can use the P+ and P- (channel up/down button) to go to next page and previous page quickly. Info - Show the information of the movie: Resolution, Audio Track, Subtitle, Program and Size.
Stop - Quit reading the text file and go back to previous menu. Music - Play the music in the background. Only music file placed in the same directory with the text file will be played. Playlist - Show the playlist of the text folder. You can use the P+ and P- (channel up/down button) to go to next page and previous page quickly. Info. - Show the size of the text file. 11. DVD Operation 11.1. Basic Operation Switch on the ON/OFF button of the RCU and push the SOURCE button to select DVD mode.
The screen will show next: With the ▼ / ▲ button you can select the desired Picture Modus. If selected PERSONAL and push the OK button, you will enter the Personal Picture setting and the screen will show next > With the ▼ / ▲ button you can select CONTRAST / BRIGHTNESS / COLOUR / SHARPNESS / COLOUR TEMP / NOISE REDUCTION and DYNAMIC CR.
The Contrast setting is shown of current setting ( on picture this is 58% ) If you want to adjust the setting, please push the OK button. Next menu is shown > With the ◄ / ► button you can adjust the contrast setting. Push EXIT to leave the OSD Menu or push MENU button to return to previous menu. For any other Personal setting you follow the same way and follow the instructions. 11.4 Sound Menu: Refer to Chapter 7.3. 11.5 Tijd Menu: Refer to Chapter 7.4. 11.6 Beveiliging Menu: Refer to Chapter 7.5 11.
12. REFERENCE 12.1 Cleaning LCD Monitor 1. Please make sure that you have turned off this machine. 2. Do not expose liquid of any kind on the LCD Monitor or plastic box. Please NOTE when cleaning the LCD monitor. 1. Gently wipe the screen with a clean, soft, lint-free cloth to remove dust or other particles that can scratch the screen. 2. To clean the tough areas, use a soft, lint-free cloth with a few drops of water to remove the stubborn dirt. 3.
13. Troubleshooting Please use the following table to resolve the most common possible causes of the problem before calling service personnel. A minor adjustment may eliminate the problem and restore your TV reception. Symptom Corrective Actions Check that power is turned on. Adjust brightness and contrast. No picture screen Check input signal of TFT-LCD. Check the power connection to the unit with screen. Check Main Display selection. Check that Video cable is plugged in.
