If you leave the BHT with the battery cartridge discharged or with no battery cartridge loaded or if you replace the battery cartridge in a wrong way, the BHT may lose the data stored in it. Before cold booting (refer to Chapter 2, Section 2.3.5 "Warm and Cold Booting"), it is recommended that important data be saved into the FLASH folder or uploaded to the host PC. Cold booting will erase all data stored in the RAM. The shape of the projected area marker differs according to the original target market.
Preface Please READ through these operating instructions carefully. It will enable you to operate your BHT-200Q/200QW correctly. After you have finished reading the instructions, keep this manual handy for speedy reference.
How this book is organized This manual is made up of five chapters and appendices. Chapter 1 Quick Guide Describes the basic operating method of the BHT and the related notes. Chapter 2 Getting Started the BHT and System Mode Summarizes the BHT system configuration and describes the operation including preparation and System Mode (which is required for the efficient use of application programs).
Related Publications BHT-200 API Reference Manual Screen Indication The lettering in the screens in this manual is a little different from that in the actual screens. File names used are only for description purpose, so they will not appear if you have not set files having those names.
SAFETY PRECAUTIONS Be sure to observe all these safety precautions. Please READ through these instructions carefully. They will enable you to use the BHT and CU correctly. Always keep this manual nearby for speedy reference. Strict observance of these warnings and cautions is a MUST for preventing accidents that could result in bodily injury and substantial property damage. Make sure you fully understand all definitions of these terms and symbols given below before you proceed to the text itself.
Handling the battery cartridge • Never disassemble or heat the battery cartridge, nor put it into fire or water; doing so could cause battery-rupture or leakage of battery fluid, resulting in a fire or bodily injury. • Do not carry or store the battery cartridge together with metallic ball-point pens, necklaces, coins, hairpins, etc. Doing so could short-circuit the terminal pins, causing the batteries to rupture or the battery fluid to leak, resulting in a fire or bodily injury.
Handling the CU • If smoke, abnormal odors or noises come from the CU, immediately unplug the AC adapter from the wall socket or CU and contact your nearest dealer. Failure to do so could cause fire or electrical shock. • If foreign material or water gets into the CU, immediately unplug the AC adapter from the wall socket or CU and contact your nearest dealer. Failure to do so could cause fire or electrical shock.
Handling the battery cartridge • Never charge a wet or damp rechargeable battery cartridge. Doing so could cause the batteries to break, generate heat, rupture or burn. Handling the BHT • Never put the BHT in places where there are excessively high temperatures, such as inside closed-up automobiles, or in places exposed to direct sunlight. Doing so could affect the housing or parts, resulting in a fire. • Avoid using the BHT in extremely humid or dusty areas, or where there are drastic temperature changes.
Handling the CU • Never put the CU in places where there are excessively high temperatures, such as inside closed-up automobiles, or in places exposed to direct sunlight. Doing so could affect the housing or parts, resulting in a fire. • Avoid using the CU in extremely humid or dusty areas, or where there are drastic temperature changes. Moisture or dust will get into the CU, resulting in malfunction, fire or electrical shock.
! Proper Care of the BHT and CU Clean the housings, BHT charge terminals, battery cartridge terminals, and CU-200 charge terminals with a dry, soft cloth. Before cleaning, be sure to turn the BHT power off and unplug the AC adapter of the CU. • Never use benzene, alcohol, or other organic solvents. The housing may be marred or the paint may come off. • Never rub or strike the liquid crystal display (LCD) with anything hard. The LCD surface will be easily scratched or broken.
DENSO WAVE INCORPORATED does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. If it is judged by DENSO WAVE INCORPORATED that malfunction of the product is due to the product having been dropped or subjected to impact, repairs will be made at a reasonable charge even within the warranty period.
Chapter 1 Quick Guide Chapter 2 Getting Started the BHT and System Menu Chapter 3 Communications Operations of the BHT-200Q/200QW Chapter 4 Error Messages Chapter 5 Handling the CU-200 (Option) Appendices
Chapter 1 Quick Guide This chapter describes the basic operating method of the BHT and the related notes. 1.1 Reading 2D Codes and Bar Codes..................................................................................................................... 2 1.2 Setting and Using the Hand Strap and Stylus .................................................................................................... 4 1.3 Setting the Frontlight ....................................................................
1.1 Reading 2D Codes and Bar Codes Turn the BHT on, bring the reading window to a target 2D or bar code, and press the trigger switch. The BHT turns the marker beam (laser) and illumination LED on to indicate the scanning range and scan the target code, respectively. When the BHT has read the code successfully, the indicator LED illuminates in blue. Code scanning range indicated by the marker beam Power key Indicator LED Illuminates in blue when the BHT has successfully read the target code.
Chapter 1 Quick Guide • If the BHT fails to read due to specular effects or other factors, change the scanning angle of the reading window or the distance from codes as shown at right, and try it again. (Specular effects occur when the reflection of the light from the code becomes excessively strong. This can easily happen when the illumination LED lights codes perpendicularly or due to the angle of ambient intense lighting to codes.) • The actual scanning range is narrower than the marker range.
1.2 Setting and Using the Hand Strap and Stylus Setting the hand strap Hand strap Using the hand strap Put your hand through the hand strap and hold the BHT as shown below. This will prevent you from dropping the BHT accidentally.
Chapter 1 Quick Guide Using the stylus The BHT has a touch screen LCD. With the stylus that comes with the BHT, you can operate keys, menus, and icons displayed on the touch screen. Before using the touch screen, be sure to set it up. (Refer to Chapter 2, Section 2.3.2, "Setting-up 2: Calibrating the touch screen.") • Always use the stylus to operate the touch screen. Do not use your fingernails or any pointed or hard object or apply a strong pressure or impact to the LCD.
1.3 Setting the Frontlight 30-key pad Pressing the right-hand trigger switch (M4 key) with the SF/ALP key held down activates or deactivates the frontlight function. Frontlight OFF (The frontlight function is OFF when you turn the BHT power on.) Press the right-hand trigger switch while holding down SF/ALP. Right-hand trigger switch (M4) Frontlight ON Press the right-hand trigger switch while holding down SF/ALP. If no key is pressed for 3 seconds.
Chapter 1 Quick Guide 26-key pad Pressing the right-hand trigger switch (M4 key) with the SF key held down activates or deactivates the frontlight function. Frontlight OFF (The frontlight function is OFF when you turn the BHT power on.) Press the right-hand trigger switch while holding down SF. Right-hand trigger switch (M4) Frontlight ON Press the right-hand trigger switch while holding down SF. If no key is pressed for 3 seconds.
1.4 Using the Keypad Entering Numerical Data To enter numerical data, use the numerical keys and the ENT key. For example, to enter the number "120," press the 1, 2 and 0 keys and then press the ENT key. If you type in any wrong value, press the C/BS (BS) key and then enter the correct one. Entering alphabetic characters The alphabet entry procedure differs depending upon the keypad type. 30-key pad Holding down the SF/ALP key only for the specified period (1.
Chapter 1 Quick Guide 1.5 Transferring Data Using radio link (BHT-200QW only) Using radio waves, the BHT-200QW may transfer data to an access point in a spread spectrum communications system. If there are too many communications errors, first make sure that the BHT-200QW points directly at an access point. Host PC Access point Built-in antenna For data transfer using radio link, it is necessary to configure a wireless local area network (wireless LAN) connecting the BHT-200QW and access points.
! Using infrared link Using infrared rays, the BHT may transfer data directly to the host PC equipped with an IrDA interface port and other IrDA-compliant devices. • Make sure that there is no obstruction in the light path between the BHT and any target stations. In infrared communication, you need to keep the BHT and any target stations within the effective infrared radiation range, usually 15 cm (5.9").
Chapter 2 Getting Started the BHT and System Menu This chapter summarizes the BHT system configuration and describes the operation including preparation and System Menu (which is required for the efficient use of application programs). 2.1 BHT System Configuration................................................................................................................................ 12 2.2 Components..................................................................................................
2.1 BHT System Configuration The BHT code data collection system requires the following hardware as well as the BHT Bar Code Handy Terminal (which reads 2D codes and bar codes and accepts keypad entry), depending upon the intended system configuration. • Host PC: Allows you to edit, manage and download user programs and data, as well as downloading system programs.
Chapter 2 Getting Started the BHT and System Menu In addition, the BHT-200QW may operate in a radio communications system (spread spectrum communication) by connecting with access points by a wireless local area network (wireless LAN).
BHT Operating System (OS) Microsoft Windows CE .NET 4.
Chapter 2 Getting Started the BHT and System Menu Software Development Kit BHT-200 Software Development Kit named "BHT200_xxxA_SDK.msi" (xxx: version) - This is a library to be embedded into Microsoft eMbedded Visual C++ 4.0 for developing applications for the BHT-200Q/200QW. - For details about the BHT-200 Software Development Kit, refer to the "BHT-200 API Reference Manual.
2.2 Components 2.2.1 Names and Functions Synchronization LED* Flashes during wireless communication. *Provided on the BHT-200QW. Indicator LED Illuminates in blue when the BHT has successfully read a 2D code or bar code. Charge LED Illuminates in red during charging and turns green at completion of charging. Built-in antenna* Do not cover this antenna section with metalevaporated tape or by hand. Doing so may result in communications failures.
Chapter 2 Getting Started the BHT and System Menu Grip style BHT Trigger switch (M5 key) Press this switch to start code reading.
The functions of the keys may be set by user programs. Shown below is a set of sample functions. 30-key pad Power key Turns the BHT on or off. Trigger switch (M3 key) Trigger switch (M4 key) Magic keys (M1 to M5*) These keys may be used as an SF key, ENT key, CTRL key, ALT key, TAB key, frontlight function on/off key, marker key or trigger switch depending upon definition in System Menu or in user programs. By default, the [M3] to [M5]* keys act as a trigger switch.
Chapter 2 Getting Started the BHT and System Menu 26-key pad Power key Turns the BHT on or off. Trigger switch (M3 key) Trigger switch (M4 key) Magic keys (M1 to M5*) These keys may be used as an SF key, ENT key, CTRL key, ALT key, TAB key, frontlight function on/off key, marker key or trigger switch depending upon definition in System Menu or in user programs. By default, the [M3] to [M5]* keys act as a trigger switch C (Clear) key Pressing this key in BHTSHELL returns to the previous screen.
2.2.2 Status Indicators on the LCD Windows desktop on 30-key pad type Windows desktop on 26-key pad type Status indicators Status indicators Battery voltage level Shows the current battery voltage level. Displays when the voltage level is high. Displays when the voltage level is low. The grip style BHT shows two icons as shown below. The upper one is for the battery cartridge loaded in the BHT body and the lower one for that in the grip.
Chapter 2 Getting Started the BHT and System Menu Synchronization state (Provided on the BHT-200QW) Displays the open state of the wireless device and the radio field intensity. Displays when the wireless device is open. Shows the radio field intensity with the number of bars. The radio field intensity icons ( , , and ) indicate that the radio link is established but do not assure you that there will be few communications errors. Keypad shift state Displays when the keypad is shifted.
2.2.3 Notes for Using the BHT Windows desktop on the LCD The Windows desktop shown in this manual may be a little different from that in the actual screens on the LCD. (Windows desktop sample) This task tray also may be a little different from that in the actual screen. No refreshing of the LCD screen when on standby To minimize the power consumption, the BHT automatically switches to the standby mode after it has not been operated for the specified period*.
Chapter 2 Getting Started the BHT and System Menu 2.3 Preparation 2.3.1 Setting-up 1: Loading the battery cartridge Before the first use of the BHT, be sure to load the battery cartridge as shown below. The battery cartridge is not loaded in the BHT when shipped from the factory. Into the BHT body (1) Turn the BHT upside down. (2) Slide the release buttons in the direction shown below and remove the battery cartridge cover. (3) Push the battery cartridge into the BHT.
Into the grip (1) Take the bottom cover off the grip by removing the screw. Grip Bottom cover Screw (2) Pull the lock in the direction of the arrow and insert the battery cartridge into the grip with the boss facing as shown below. Boss Battery cartridge Lock (3) Secure the bottom cover to the grip with the screw.
Chapter 2 Getting Started the BHT and System Menu • Never disassemble or heat the battery cartridge, nor put it into fire or water; doing so could cause battery-rupture or leakage of battery fluid, resulting in a fire or bodily injury. • Do not carry or store the battery cartridge together with metallic ball-point pens, necklaces, coins, hairpins, etc. Doing so could short-circuit the terminal pins, causing the batteries to rupture or the battery fluid to leak, resulting in a fire or bodily injury.
Battery Voltage Level on the Status Indicator Line The battery voltage level is always displayed on the status indicator line. (For details, refer to Section 2.2.2 "Status Indicators on the LCD.") Low Battery Indication Low battery warning If the battery output voltage drops below a specified lower level limit when the BHT is in operation, the BHT displays the following message for approx. 2 seconds and beeps three times. After that, it will resume previous regular operation.
Chapter 2 Getting Started the BHT and System Menu Grip style BHT As long as the voltage level of either one of battery cartridges loaded in the BHT body and grip is higher than the specified level, no low battery messages will appear. If any low battery message appears, therefore, you need to replace both battery cartridges. Even if you only have one fully-charged replacement battery cartridge on hand, remove both batteries.
2.3.2 Setting-up 2: Calibrating the touch screen Press the power key to turn on the BHT. The calibration screen appears, so follow the on-screen instructions. If nothing appears, first perform a "cold boot" (refer to Section 2.3.5). The "+" appears first at the center of the screen as shown at left. Tap the center of the "+" with the stylus for one second, and the "+" moves to the upper left. Tap its center, and it moves to the bottom left.
Chapter 2 Getting Started the BHT and System Menu 2.3.3 Battery Replacement Notes When is battery replacement needed? If the "Charge the battery!" appears on the LCD, replace the battery cartridge with a fully charged one. If you leave the BHT without replacing the battery cartridge, then the integrated calendar clock or data will no longer be backed up so that the calendar clock may stop or the data may be lost.
2.3.4 BHT Turning-off Notes [ 1 ] "Shutdown in progress" message If you press the power key to turn off the BHT, the BHT displays the following message and starts preparation for shutdown. When the above message is displayed, do not remove the battery cartridge. If you do so, the data stored in the BHT may be lost.
Chapter 2 Getting Started the BHT and System Menu [ 2 ] Backing up the Registry The Registry is the part of Windows CE that stores setup information required for operating the BHT. Backing-up the Registry When the BHT is on, pressing the power key with the SF/ALP (SF) key held down displays the screen shown at right and starts backing up the Registry. Do not remove the battery cartridge until the backup operation is completed and the message disappears.
2.3.5 Warm and Cold Booting Warm-booting the BHT In any of the following cases, warm-boot the BHT: - The BHT makes no response to entry from the touch screen or keys. - The programs in the BHT malfunction due to any problems. Warm-booting the BHT will not erase data stored in the RAM, but it will erase data being edited and not be saved. Warm booting procedure When the BHT power is on, press the reset button with the stylus.
Chapter 2 Getting Started the BHT and System Menu Cold-booting the BHT If a problem persists even after warm-booting the BHT, cold-boot the BHT. Cold-booting the BHT will erase all data stored in the RAM. It is recommended that important data be saved into the FLASH folder or uploaded to the host PC. Cold booting procedure Turn the BHT off. While holding down the reset button with the stylus, press the power key and then release them. Press the power key again, and the BHT cold-boots.
2.4 Replacement of the Backup Battery If the following warning message appears on the LCD, you need to replace the backup battery (refer to Section 2.4.1). If you remove the backup battery, the contents of the memory may no longer be backed up so that the data stored in the BHT may be lost. It is recommended that important data be saved into the FLASH folder or uploaded to the host PC. This warning message appears each time the backup battery is fully discharged after 200 times of full discharges.
Chapter 2 Getting Started the BHT and System Menu 2.4.1 Replacing the Backup Battery Before proceeding to the replacement procedure below, it is recommended that you save important data into the FLASH folder or upload it to the host PC. (1) Turn the BHT upside down. (2) Slide the right and left release buttons in the direction of the arrows to remove the battery cartridge cover. Release button Battery cartridge cover Release button (3) Pull up the battery pull strap to remove the battery cartridge.
(4) Pull the lock of the inside cover to the right and towards you to release it. Inside cover Lock Lock Inside cover (5) Pull the right end of the clear insulation sheet up and out of the BHT.
Chapter 2 Getting Started the BHT and System Menu (6) Slide the backup battery cover to the right and take it out. Backup battery cover (7) Lift up the backup battery, take its lead wires out of the groove, and disconnect the battery connector as shown below.
(8) Connect the connector of a new backup battery with the red lead facing to the left. (9) Route the lead wires inside the guides through the groove. For easier routing, use a tool whose tip is thin and round. (10) Load the backup battery. Backup battery Red lead Black lead Guides Groove Backup battery (11) Slide the backup battery cover back into place.
Chapter 2 Getting Started the BHT and System Menu (12) Set the clear insulation sheet back into place while threading the battery pull strap through the cutout in the sheet. Battery pull strap Clear insulation sheet (13) Set the inside cover so that its lock and pawl become fitted between the printed circuit boards.
(14) Push the battery cartridge into the BHT. The end of the battery pull strap should come out from the left edge of the battery cartridge. Battery cartridge Battery pull strap (15) Set the battery cartridge cover back into place and return the right and left release buttons to the original position.
Chapter 2 Getting Started the BHT and System Menu 2.4.2 Resetting the Discharge Counter If you replace the backup battery, reset the internal discharge counter in the BHTSHELL System Properties Menu. For detailed operation, refer to Section 2.5.4, "[3.3] Device Menu, Backup Battery Discharge Counter.
2.5 Operating in System Menu 2.5.1 Desktop Upon completion of setting-up 2 (described in Section 2.3.2), the desktop appears on the touch screen as shown below. Double-tapping icons on the desktop runs the corresponding programs. Recycle Bin On the desktop, double-tap Recycle Bin. The Recycle Bin opens. The Recycle Bin stores files you deleted in the BHT. To retrieve files stored in the Recycle Bin, select the file to be retrieved and choose File | Restore.
Chapter 2 Getting Started the BHT and System Menu My Computer On the desktop, double-tap My Computer. The screen shown at left appears. With this program, you can browse the file information in the BHT. Internet Explorer On the desktop, double-tap Internet Explorer. The screen shown at left appears. With this program, you can browse Web pages. Before running Internet Explorer, you need to make RF-related settings and open the wireless communications device. For details, refer to Section 2.5.4, "[3.
BHTSHELL On the desktop, double-tap BHTSHELL. The System Menu screen shown at left appears. For details about this program, refer to Section 2.5.3, "Operating in System Menu.
Chapter 2 Getting Started the BHT and System Menu 2.5.2 Start Menu Tap the Start button in the bottom left corner of the desktop. The Start menu appears where you can run programs and make system settings. Terminal On the Start menu, tap Programs | Communication | Terminal. The screen shown at left appears. You can create a new session. Internet Explorer On the Start menu, tap Programs | Internet Explorer to run Internet Explorer. For details, refer to Section 2.5.1, "Desk Top, Internet Explorer.
Command Prompt On the Start menu, tap Programs | Command Prompt. The screen shown at left appears. Favorites On the Start menu, tap Favorites. Your Favorites list appears. To add items to your Favorites list, create a shortcut(s) of the desired file(s) in the \Windows\favorites folder. Documents On the Start menu, tap Documents. Recently opened documents appear. To add files to the Start menu, use the standard API "SHAddToRecentDocs().
Chapter 2 Getting Started the BHT and System Menu System Properties On the Control Panel window, double-tap System, and the System Properties window appears. Tap the General tab to display the screen shown at left. Choose the Memory tab to display the screen shown at left. You can check the memory allocation and the free space of the RAM. You can also change the memory allocation by moving the slider.
Dialing Properties On the Control Panel window, double-tap Dialing, and the Dialing Properties window appears. You can set up the telephone line. Owner Properties On the Control Panel window, double-tap Owner, and the Owner Properties window appears. Tap the Network ID tab to display the window shown at left. You can specify a user name, password and domain required to access the network resource.
Chapter 2 Getting Started the BHT and System Menu Volume & Sounds Properties On the Control Panel window, double-tap Volume & Sounds, and the Volume & Sounds properties window appears. Tap the Volume tab to display the screen shown at left.
Display Properties On the Control Panel window, double-tap Display, and the Display Properties window appears. Tap the Background tab to display the screen shown at left. You can select wallpaper to be displayed on your desktop. Tap the Appearance tab to display the screen shown at left. You can specify the appearance of your desktop. Regional Settings Properties On the Control Panel window, double-tap Regional Settings, and the Regional Settings Properties window appears.
Chapter 2 Getting Started the BHT and System Menu Connection On the Control Panel window, double-tap Network and Dial-up Connection, and the Connection window appears. Double-tap the "Make New Connection" icon starts Wizard. Follow the Wizard instructions and set the connection name and type. PC Connection Properties Tap the PC Connection tab to display the screen shown at left. You can change the connection method to the PC. Tap the Change Connection button.
Date/Time Properties On the Control Panel window, double-tap Date/Time, and the Date/Time Properties window appears. You can specify the date, time and time zone. The entry range to the year is 2003 to 2099. Input Panel Properties On the Control Panel window, double-tap Input Panel, and the Input Panel Properties window appears. Tap the Options button to display the screen shown at left. You can switch the input panel (software keyboard) between large and small keys.
Chapter 2 Getting Started the BHT and System Menu Taskbar On the Start menu, tap Settings | Taskbar. The Taskbar and Start Menu window appears. Tap the General tab to display the screen shown at left. You can customize the taskbar. Run On the Start menu, tap Run, and the screen shown at left appears. You can run applications or open files.
2.5.3 Operating in System Menu On the desktop, double-tap BHTSHELL. System Menu starts up to display the following screen: To run the items in System Menu, tap the desired item or press the corresponding numerical key. To quit System Menu, tap the or button located in the top right corner of the window. The keys below are so designed that the function of each key is consistent in every screen.
Chapter 2 Getting Started the BHT and System Menu Structure of System Menu System Menu Double-tapping the BHTSHELL shortcut icon on the desktop starts up System Menu. Execute Program Executes a user program you select. Menu 1 (Refer to Section 2.5.4, [ 1 ].) Communication SF + C/BS (C) keys Communicates with the host PC. Menu 2 (Refer to Section 2.5.4, [ 2 ].) System Properties Sets a variety of environmental conditions. Menu 3 (Refer to Section 2.5.4, [ 3 ].
Hardware Test Tests a variety of hardware operations. Menu 4 (Refer to Section 2.5.4, [ 4 ].) SF + C/BS (C) keys Explorer Runs Explorer. Menu 5 (Refer to Section 2.5.4, [ 5 ].) System Information Shows the system program version and memory size. Menu 6 (Refer to Section 2.5.4, [ 6 ].
Chapter 2 Getting Started the BHT and System Menu 2.5.4 Detailed Description of the Functions in System Menu [ 1 ] Execute Program Choosing "1:Execute Program" in System Menu calls up the screen shown at left. With this menu, you can start an application you want. ⇓ Tap the Browse button. The screen shown at left appears. Select a file you want to run, check that the file name is displayed in the Name box, and then tap the OK button.
[ 2 ] Communication Menu Choosing "2:Communication" in System Menu calls up the screen shown at left. [1] Ymodem: Switches to the Ymodem menu where you can set the Ymodem communications parameters and download/upload files. [2] ActiveSync (IrDA): Connects to the host PC via IrDA using ActiveSync. [3] ActiveSync (RF): Connects to the host PC via RF using ActiveSync. [4] ActiveSync (USB): Connects to the host PC via USB using ActiveSync. [2.
Chapter 2 Getting Started the BHT and System Menu Setting the communications environments Tapping button on the Ymodem menu calls up the communications environments setting screen. To communicate with the host PC via the IrDA interface port, select "IrDA (COM4:)" in Port. The screen shown at left appears In BaudRate, select the same setting as that in the host PC.
! Downloading Specify a folder where you want to store a downloaded file and then tap button , and the BHT waits for a file to be downloaded. Folder where you want to store a downloaded file If you download a file having the same name as one already in the same folder, the newly downloaded file replaces the old one. ⇓ Upon completion of downloading, the BHT sounds a long beep once and displays the screen shown at left.
Chapter 2 Getting Started the BHT and System Menu If an error occurs during downloading If some error occurs during downloading, the BHT beeps three times and shows one of the following screens. ! Problem The memory is insufficient for storing files to be downloaded. ! Solution Delete unnecessary files in the memory or decrease the size of the file to be downloaded. ! Problem The path of the file to be downloaded is too long.
! Problem Downloading has failed. ! Solution Confirm the communications environment settings and then retry the download. It is also necessary to check the communications environment setup of the host PC. ! Problem Downloading has aborted. ! Solution Confirm the communications environment communications log, then retry the download. settings and It is also necessary to check the communications environment setup of the host PC. ! Problem The communications port has been already opened.
Chapter 2 Getting Started the BHT and System Menu ! Uploading Specify a file you want to upload and then tap button waits for a file to be uploaded. , and the BHT File you want to upload ⇓ Upon completion of uploading, the BHT sounds a long beep once and displays the screen shown at left.
If an error occurs during uploading If some error occurs during uploading, one of the following screens will appear and the beeper beeps three times. ! Problem The file you attempted to upload was opened. ! Solution Close the file to be uploaded and then retry the upload. ! Problem Uploading has aborted. ! Solution Confirm the communications environment communications log, then retry the upload. settings and It is also necessary to check the communications environment setup of the host PC.
Chapter 2 Getting Started the BHT and System Menu ! Problem Timeout has occurred. ! Solution Confirm the communications environment communications log, then retry the upload. settings and It is also necessary to check the communications environment setup of the host PC. ! Problem No file has been correctly selected for uploading. ! Solution Select a file(s) to be uploaded and retry the upload.
[2.2] ActiveSync (IrDA) Choosing "2:ActiveSync (IrDA)" on the Communication menu connects the BHT to the host PC via the IrDA interface port. Upon completion of connection, the screen shown at left appears. For details about the configuration of the host PC and connection using ActiveSync, refer to Chapter 3, Section 3.5 "ActiveSync." When connecting the BHT to the host PC using ActiveSync (IrDA), arrange the BHT and host PC with their IrDA ports facing directly each other.
Chapter 2 Getting Started the BHT and System Menu [2.3] ActiveSync (RF) Choosing "3:ActiveSync (RF)" on the Communication menu connects the BHT to the host PC via the RF interface port. Before proceeding to "ActiveSync (RF)," you need to: - Set up a partnership between the host PC and BHT by running "ActiveSync (IrDA)." - Make the RF settings according to the procedure given in "[3.4] RF Menu (Network Control Interface)." If the RF settings are not made correctly, "ActiveSync (RF)" cannot run.
Upon completion of connection by ActiveSync, the screen shown at left appears. If connection to the network fails If connection to the network fails, the BHT beeps three times and displays the following screen. Solution The RF settings may have not been made correctly. According to the procedure given in "[3.4] RF Menu (Network Interface Control)," make the correct RF settings.
Chapter 2 Getting Started the BHT and System Menu [2.4] ActiveSync (USB) Choosing "4:ActiveSync (USB)" on the Communication menu connects the BHT to the host PC via the USB interface port. Upon completion of connection, the screen shown at left appears. For details about the configuration of the host PC and connection using ActiveSync, refer to Chapter 3, Section 3.5 "ActiveSync.
[ 3 ] System Properties Menu Choosing "3:System Properties" in System Menu calls up the screen shown at left. [3.1] [1] Control Panel: Opens the control panel. [2] File System: Opens the file system related menu. [3] Device: Opens the device related menu. [4] Radio Frequency: Opens the RF related menu. Control Panel Choosing "1:Control Panel" in the System Properties menu calls up the screen shown at left. With this menu, you can set up the basic Windows operating environment.
Chapter 2 Getting Started the BHT and System Menu [3.2] File System Choosing "2:File System" in the System Properties menu calls up the screen shown at left. With this menu, you can perform the following transactions: Initializing the memory excluding the Registry Initializing the memory including the Registry Initializing the FLASH folder Running Scandisk through the FLASH folder The table below shows which memory area will be initialized by the initialization transactions listed above.
Initializing the memory excluding the Registry You can initialize the memory excluding the Registry and files stored in the FLASH folder. Initializing procedure (1) Tap the Initialize tab and select the RAM radio button. (2) Tap the Initialize button. ⇓ ⇑ Select No. (3) To initialize the memory, tap the Yes button; to return to the previous menu, tap the No button. ⇓ Select Yes. After the BHT displays the screen shown at left for a few seconds, it will automatically reboot.
Chapter 2 Getting Started the BHT and System Menu Initializing the memory including the Registry You can initialize the memory including the Registry but excluding files stored in the FLASH folder. Initializing procedure (1) Tap the Initialize tab and select the RAM radio button. (2) Select the Initialize Registry check box (3) Tap the Initialize button. ⇓ ⇑ Select No. (4) To initialize the memory, tap the Yes button; to return to the previous menu, tap the No button. ⇓ Select Yes.
Initializing the FLASH folder You can erase all information stored in the FLASH folder and let the folder revert to the initial state. Initializing procedure (1) Tap the Initialize tab and select the FLASH radio button. (2) Tap the Initialize button. ⇓ ⇑ Select No. (3) To initialize the memory, tap the Yes button; to return to the previous menu, tap the No button. ⇓ Select Yes. Upon completion of initialization (it will take approx. one minute), the screen shown at left appears.
Chapter 2 Getting Started the BHT and System Menu Running Scandisk through the FLASH folder If the power to the BHT is shut down when the FLASH folder is being accessed, some broken file fragments may remain in the FLASH folder so that the free memory space will be decreased. To remove or clear those fragments, run Scandisk through the FLASH folder. Initializing procedure (1) Tap the Scandisk tab and select the Scandisk button. ⇓ ⇑ Select No.
[3.3] Device Menu Choosing "3:Device" in the System Properties menu calls up the screen shown at left. [1] QRcode: Opens the QRcode setting menu. [2] Beeper/Vibration: Opens the beeper/vibration switching menu. [3] Display: Opens the display setting menu. [4] Key: Opens the key setting menu. [5] Frontlight: Opens the frontlight setting menu. [6] Power Management: Open the power management menu. QR code setting menu Choosing "1:QRcode" on the Device menu calls up the screen shown at left.
Chapter 2 Getting Started the BHT and System Menu Mirror image 2D code reading function (REVERSE) This function makes it possible to read a mirror image 2D code label. The mirror image 2D code reading is enabled, the time required for reading may increase. DECODE LEVEL You may set the decode level. Decreasing the level value increases the code reading efficiency, but the BHT might misread low-quality codes (split or stained).
MARKER You can select the marker ON/OFF mode from the following: 0: Normal mode driven by the trigger switch 1: Marker-ON mode 2: Marker-OFF mode OPTION DATA If the Option Data is set ON, the BHT will add option data (containing 2D code model and error correction level) to the tail of 2D code data when it reads a 2D code. This setting takes effect not only in the reading test in System Mode but also in any other operations.
Chapter 2 Getting Started the BHT and System Menu Example: If a code read is "Data Matrix, Error correction level ECC200, 10 cells wide by 10 cells high," then the option data below will follow. (Data read)... Z0200010010 Minimum number of digits to be read for ITF or Codabar You can set the minimum number of digits to be read for ITF and Codabar.
Beeper/vibrator switching menu Choosing "2:Beeper/Vibration" on the Device menu calls up the screen shown at left. On this menu, you can adjust the beeper volume and switch the beeper and vibrator. Adjusting the beeper volume Choose the Volume tab to display the screen shown at left where you can select the beeper volume for the following operations. Beeper: From the six levels 0 (low) to 5 (high). (Default: 5) Beeper volume to be applied when any key is pressed.
Chapter 2 Getting Started the BHT and System Menu Display setup menu Choosing "3:Display" on the Device menu calls up the screen shown at left. [1] Calibration: Opens the touch screen calibration screen. [2] Status Display: Opens the status indicator on/off menu. Calibrating the touch screen Choose "1:Calibration" on the Display setup menu to call up the screen shown at left. Follow the on-screen instructions. Refer to Section 2.3.2 "Setting-up 2: Calibrating the touch screen.
Key definition menu Choosing "4:Key" on the Device menu calls up the screen shown at left. You can define the functions of the following keys: - SF/ALP (SF) key - M1 key - M2 key - M3 key - M4 key - M5 key* - M3 key (pressed halfway) - M4 key (pressed halfway) - M5 key* (pressed halfway) *Available on the grip style BHT Defining the SF/ALP (SF) key for keypad shift Choose the SHIFT tab on the Key definition menu to display the screen shown at left.
Chapter 2 Getting Started the BHT and System Menu Defining the M1, M2, M3 (left-hand trigger switch), M4 (right-hand trigger switch), and M5* keys *M5 key available on the grip style BHT Choose the MAGIC Full-press tab on the Key definition menu to display the screen shown at left. You can define each of the M1 through M5* keys as any one of a trigger switch, shift key, enter key, frontlight function on/off key, Tab key and others as listed below.
If you define the M4 key as a frontlight function on/off key, pressing the M4 key activates or deactivates the frontlight function. Note that the frontlight function on/off key can be assigned only to any one of M1 through M5* keys and halfway pressed M3 through M5* keys. The key defined more recently will act as a frontlight function on/off key and one defined earlier will be ignored.
Chapter 2 Getting Started the BHT and System Menu Frontlight menu Choosing "5:Frontlight" on the Device menu calls up the screen shown at left. - Frontlight function (Note 1) Enable or disable the frontlight function. If it is enabled, the frontlight comes on when you press any key or tap the touch screen. - Time (Frontlight ON-duration) Set the ON-duration of the frontlight that comes on when you press any key or tap the touch screen. Battery Power: ON-duration when the BHT is not placed on the CU.
Power Management menu Choosing "6:Power Management" on the Device menu calls up the screen shown at left. You can set the automatic power-off timer, the standby timer, and CPU clock. Automatic Power-Off Time: Battery Power: For the BHT being out of the CU, set the automatic power-off timer. (Default: 180) External Power: For the BHT placed in the CU, set the automatic power-off timer. (Default: 0) The entry range for the above items is from 0 to 32767 in units of seconds.
Chapter 2 Getting Started the BHT and System Menu Backup Battery Discharge Counter On the Device menu, pressing the 0 key with the SF/ALP (SF) key held down calls up the screen shown at left. This screen displays the discharge count of the backup battery. If you replace the backup battery, tap the Reset button to reset the discharge counter to zero. Only after the discharge count reaches 200, the counter can be reset to zero.
[3.4] RF Menu (Network Interface Control) Choosing "4:Radio Frequency" in the System Properties menu calls up the screen shown at left.
Chapter 2 Getting Started the BHT and System Menu Displaying the IP address and MAC address Tapping the Network tab on the NIC Control menu displays the screen shown at left.
Setting the RF options Tapping the Option tab on the NIC Control menu displays the screen shown at left. You can set the following: Power: Select the power mode for the wireless module. For details about the parameters above, refer to Chapter 3, Section 3.1.2 "RF-Related Parameters." Setting the WEP keys Tapping the WEP tab on the NIC Control menu displays any of the following three types of screens according to the authentication type.
Chapter 2 Getting Started the BHT and System Menu (128-bit WEP) Displaying the current communications link status Tapping the Link tab on the NIC Control menu displays the screen shown at left where the current communications link status appears in real-time. Associated Access Point: Displays the MAC address assigned to the wireless interface of the associated access point. Signal Strength: Displays the signal intensity of receive packets.
Testing with Ping Tapping the Ping tab on the NIC Control menu displays the screen shown at left. Dest IP: Specify the IP address of a host PC that you want to ping. Data size: Specify the data size of an echo request. Interval: Specify the echo request intervals (in units of 100 ms). Timeout: Specify the timeout period (in units of 100 ms) for an echo request. Type 1 or Type 2: Select the echo request send timing Type 1 or Type 2 (described on the next page).
Chapter 2 Getting Started the BHT and System Menu Ping Echo Request Send Timing Two types of echo request send timings are available: Type 1 and Type 2. The default is Type 2. • Type1 After sending an echo request, Ping will wait for the period specified by Interval and then send an echo request again. For Type 1, the relationship between the Interval and Timeout should be "Interval ≥ Timeout.
[ 4 ] Test Menu Choosing "4:Test" in System Menu calls up the screen shown at left. [1] QRCODE: Select the 2D-code and bar-code reading test. [2] BEEPER: Select the beeper scale test. [3] AGING: Select the aging test. [4] COM: Select the communications test. [5] DISPLAY: Select the LCD and indicator LED. [6] KEY VIBRATION: Select the key entry and vibrator test. If an error occurs in any of the above tests, contact your nearest dealer.
Chapter 2 Getting Started the BHT and System Menu [4.1] QR code reading test Selecting "1: QRCODE" on the Hard Test menu calls up the screen shown at left. Actually read codes with the BHT and check that the code data read matches ones displayed on the LCD. ⇓ Code type Number of digits of the code Data Upon completion of code reading, the BHT beeps once, turns on the indicator LED in blue, and displays the read data together with the code type and the number of digits.
The QR Code symbology can split data into a maximum of 16 blocks and encodes each of them into a split QR code image. When reading split QR codes, the BHT beeps in a different way from usual. That is, when the BHT reads the first split code, it beeps twice and enters the split code scanning mode. After that, each time it reads the subsequent split code, it beeps once. If the BHT reads the last split code, it beeps three times and completes the sequence of split code scanning.
Chapter 2 Getting Started the BHT and System Menu [4.2] Beeper scale test Selecting "2:BEEPER" on the Hard Test menu calls up the screen shown at left and sounds the beeper at three octaves listed below. Upon completion of this test, the BHT automatically returns to the Hard Test menu. Scale [4.
[4.4] Communications test In System Menu, you can test the IrDA interface port and USB interface port. Preparation for the IrDA interface test Arrange two BHTs, one as a master station and the other as a slave station (to be tested) with their IR ports facing each other as illustrated below. In this test, the slave BHT transmits data to the master BHT and receives the data sent back from the master BHT. Data 0.15 m (5.
Chapter 2 Getting Started the BHT and System Menu Testing the IrDA interface port Selecting the "1:OPTICAL" on the COM menu calls up the screen shown at left. At the slave BHT to be tested, select the "1:SLAVE" and at the master BHT, select the "2:MASTER." Then press the ENT key on each BHT. During the test, the screen shown at left is displayed.
If the IrDA interface test ends abnormally: If the test ends due to a timeout error, the tested slave BHT beeps three times and displays the screen as shown at left. This sample screen shows that an error has occurred at 9600 bps. If the test ends due to mismatch between the sent data and received data, the tested slave BHT beeps three times and displays the screen as shown at left. This sample screen shows that the received data is 255 although data 43 has been sent at 9600 bps.
Chapter 2 Getting Started the BHT and System Menu Testing the USB interface port Selecting the "2:USB" on the COM menu calls up the screen shown at left and starts connecting with the host PC using ActiveSync. For the configuration of the host PC and details about ActiveSync, refer to Chapter 3, Section 3.5 "ActiveSync.
To terminate the USB interface test There are two ways to terminate the USB interface test--"Disconnect the USB interface cable" and "Disconnect the link with the button in the task tray (as described below)." (1) Double-tap the ActiveSync icon (circled in red at left) in the task tray. (2) The dialog appears as shown at left. Tap the Disconnect button (circled in red). The BHT beeps once and disconnects the ActiveSync connection. The ActiveSync icon disappears.
Chapter 2 Getting Started the BHT and System Menu [4.5] LCD and indicator LED tests Selecting "5:DISPLAY" on the Hard Test menu calls up the test pattern shown at left on the LCD and turns on the indicator LED in blue. Each time the ENT key is pressed, the screen shifts to the next test pattern. To return to the previous screen, press the C/BS (BS) key. To stop this test while in progress and return to the Hard Test menu, press the C/BS (C) key.
The checker pattern is reversed. C/BS (BS) key ⇑ ⇓ ENT key The gray screen appears with a one-dot wide white outline. C/BS (BS) key ⇑ ⇓ ENT key Forty eight right-angled triangles appear.
Chapter 2 Getting Started the BHT and System Menu The gradation pattern appears. Press the ENT key, and the BHT returns to the Hard Test menu.
[4.6] Key entry and vibrator test Selecting "6:KEY VIBRATION" on the Hard Test menu calls up the screen shown at left and makes the BHT ready for entry from the keypad. Pressing individual keys displays the identifier letters in the positions pre-assigned to those keys on the LCD. Pressing the same key again erases the displayed letter. 30-key pad type The table below shows the relationship between the keys and the identifier letters to be displayed on the LCD.
Chapter 2 Getting Started the BHT and System Menu 26-key pad type The table below shows the relationship between the keys and the identifier letters to be displayed on the LCD. Key M1 M2 M3 M4 M5* M3 halfway pressed M4 halfway pressed M5* halfway pressed SF BS Letter Key Letter Key Letter ^ v < > M1 M2 M3 M4 M5 M3H M4H M5H SF BS 1 2 3 4 5 6 7 8 9 0 . ENT C ALP 1 2 3 4 5 6 7 8 9 0 .
[ 5 ] Explorer Choosing "5:Explorer" in System Menu calls up the screen shown at left. [ 6 ] System Information Choosing "6:Version" in System Menu calls up the screen shown at left.
Chapter 3 Communications Operations of the BHT-200Q/200QW Describes the communications operations of the BHT—the spread spectrum communication (BHT-200QW only), infrared communication, USB interface specifications, basic communications specifications, communication using Ymodem, and ActiveSync--for data transfer with the host PC or other devices. 3.1 Spread Spectrum Communication..................................................................................................................... 110 3.1.
3.1 Spread Spectrum Communication 3.1.1 Notes for Wireless Operations The BHT-200QW supports spread spectrum communication. • If there are too many communications errors, first make sure that the BHT-200QW points directly at an access point because the 2.4-GHz band requires a more or less straight line path. Note also that the low-power radio waves have trouble passing through human bodies and other obstacles along that path.
Chapter 3 Communications Operations of BHT-200Q/200QW 3.1.2 RF-Related Parameters User programs command-control wireless communication between the BHT terminals and access points which are connected each other by a wireless LAN. For the setting procedure of RF-related parameters, refer to Section 2.5.4, "[3.4] RF Menu (Network Interface Control)." ESSID (Extended Service Set ID) An ESSID is an ID that identifies the wireless network.
TRANSMIT KEY You need to use the TRANSMIT KEY in order to choose and activate any one of the WEP KEY1 through WEP KEY4 already defined. If the size of the WEP KEY specified as a TRANSMIT KEY for the BHT is different from that for the access point, no communication is possible.
Chapter 3 Communications Operations of BHT-200Q/200QW 3.2 Infrared Communication The BHT has an integrated infrared (IR) communications device which enables wireless transfer of programs and data between the BHT and the host PC and between the BHTs, instead of the conventional wire transfer.
3.3 USB Interface Specifications The BHT-200Q/200QW is equipped with a USB interface for interfacing with the host PC. (1) Specification USB1.1 Device, Full-speed compliant (2) Connector Mini - B receptacle Pin 1 Pin No.
Chapter 3 Communications Operations of BHT-200Q/200QW 3.4 Basic Communications Specifications and Ymodem 3.4.1 Basic Communications Specifications Listed below are the communications specifications when the BHT exchanges data with a host PC through the CU-200 (IrDA interface).
Transmission Code and Bit Order All characters should be coded to 8-bit code for data transmission. The transmission bit order is LSB (Least significant bit) first. What follows is an example for transmitting character A (41h, 01000001b) with an even parity and a single bit each for start and stop bits. Vertical Parity A vertical parity bit is a redundancy bit which is added to every character to be transmitted in order to check that data has been transmitted accurately.
Chapter 3 Communications Operations of BHT-200Q/200QW 3.4.2 Using Ymodem In System Menu and user programs, the BHT can use Ymodem with the following communications parameters: Port IrDA interface Transmission Speed 2400, 9600, 19200, 38400, 57600, or 115200 bps Character Length 8 bits Vertical Parity None Stop Bit Length 1 bit In System Mode Refer to Section 2.5.4, "[ 2 ] Communication Menu." In User Programs Refer to the "BHT-200 API Reference Manual.
3.5 ActiveSync With Microsoft ActiveSync, the BHT can exchange data with the host PC connected in IrDA, USB, or spread spectrum communication. ActiveSync enables the following: 3.5.1 - Synchronized data transmission - Backing up data - Copying or transferring data - Debugging user programs Configuring the Host PC Installing ActiveSync 3.7 To use ActiveSync for communication between the BHT and host PC, you need to install ActiveSync 3.7 to the host PC. Download ActiveSync 3.
Chapter 3 Communications Operations of BHT-200Q/200QW Setting up ActiveSync 3.7 Make ActiveSync connection settings according to the procedure below. Start the installed ActiveSync 3.7, and the screen shown at left appears. ⇓ Choose File|Connection Settings. The screen shown at left appears. Click the check box "Allow serial cable or infrared connection to this COM port:" and select "Infrared Port (IR).
3.5.2 Connection Using ActiveSync In IrDA communication or USB communication IrDA communication Arrange the BHT and host PC with their IrDA ports facing directly each other as shown below. No ActiveSync can be used for connection via the CU-200. Host PC IrDA communication BHT For the operating procedure of ActiveSync on the BHT, refer to Chapter 2, Section 2.5.4, "[2.2] ActiveSync (IrDA)." USB communication Connect the BHT to the host PC by using a USB interface cable as shown below.
Chapter 3 Communications Operations of BHT-200Q/200QW Setting up a partnership Upon completion of connection between the host PC and BHT, the host PC displays the screen shown at left. On this screen, set up a partnership between the host PC and BHT. Click the Yes radio button and then click Next. ⇓ Type an arbitrary BHT name in the Device name box and click Next. ⇓ To synchronize files, select the Files check box and then click Next.
Click Finish to complete the setup and return to Windows. The partnership between the BHT and host PC has been set up. For instructions on how to use ActiveSync, refer to its Help on the host PC. For debugging of user programs using ActiveSync, refer to the "BHT-200 API Reference Manual." In spread spectrum communication Like ActiveSync in IrDA communication or USB communication, ActiveSync in spread spectrum communication requires a partnership between the BHT and host PC to be set up.
Chapter 4 Error Messages This chapter lists the error messages which will appear on the LCD if some error occurs in the BHT. 4.1 System Errors ...............................................................................................................................................................
4.1 System Errors If some error occurs when the power is turned on or during program execution, one of the following error messages will appear on the LCD. System Program error Problem A System Program error has occurred. If this error occurs, the BHT beeps five times (for 0.1 second per beep) and then turns itself off. Solution Contact your nearest dealer.
Chapter 4 Error Messages Shutdown due to low battery Problem When the power is turned on or off or during execution of applications, the battery output level has lowered so that the BHT no longer operates. If lower battery is detected, the BHT beeps five times (for 0.1 second per beep) and then turns itself off. Depending upon the battery level, the beeper may not sound five times. Solution Replace or recharge the battery cartridge. (For the charging procedure, refer to Chapter 5, Section 5.5.
126
This chapter describes the handling procedure of the communication unit CU-200, the interfacing with the host PC, and the charging of the rechargeable battery cartridge. 5.1 Functions of the CU-200 .................................................................................................................................... 128 5.2 Components and Functions ............................................................................................................................... 129 5.
5.1 Functions of the CU-200 The optical communication unit CU-200 series is available in two models: CU-201 and CU-221. The CU-200 series has the following functions: (1) Data exchange function The CU-201/221 exchanges data and programs between the BHT and the host PC. Interface with the BHT: IrDA interface Interface with the host PC: RS-232C (CU-201) USB (CU-221) (2) Battery cartridge charging function The CU-200 charges the rechargeable battery cartridge loaded in the BHT.
Chapter 5 Handling the CU-200 (Option) 5.2 Components and Functions IrDA interface port Used to exchange data optically with the BHT. Status indicators POWER LED (green) Lights when the power is applied to the CU. BHT charge terminals Do not stain these terminals; doing so could result in a lower charging efficiency. DATA Communications LED (green) Lights when the BHT is communicating with the host PC. Interface connector Used to exchange data with the host PC or communications station.
5.3 Applying Power to the CU-200 CU-201: The CU-201 should be powered from a wall socket via the dedicated AC adapter. Connect the outlet plug of the AC adapter to the power inlet connector of the CU-201, then plug the other end into a wall socket. CU-221: The CU-221 should be powered from a wall socket via the dedicated AC adapter or from the USB host (PC) or USB hub via the USB interface. Connecting the AC adapter supplies power to the CU-221.
Chapter 5 Handling the CU-200 (Option) • If you are not using the CU for a long time, be sure to unplug the AC adapter from the wall socket for safety. Failure to do so could result in a fire. • When caring for the CU, unplug the AC adapter from the wall socket for safety. Failure to do so could result in an electrical shock. • Never cover or wrap up the CU or AC adapter in a cloth or blanket. Doing so could cause the unit to heat up inside, deforming its housing, resulting in a fire.
5.4 Communicating with the Host PC 5.4.1 Setting the Transmission Speed of the CU-200 CU-201: Set the transmission speed to the same value as that of the BHT and host PC, by using the DIP switch. CU-221: The transmission speed is automatically determined by the host PC. The DIP switch is located next to the power inlet connector on the side of the CU-201. (1) Remove the protection sheet of the DIP switch from the CU-201. (2) Set the selectors of the DIP switch as shown below.
Chapter 5 Handling the CU-200 (Option) 5.4.2 Interface Cable Connection (1) Unplug the AC adapter of the CU-200 from the wall socket. (2) Make sure that the host PC is turned off. (3) CU-201: CU-221: Connect the RS-232C interface cable to the interface port of the CU-201. Connect the USB interface cable to the interface port of the CU-221. Interface cable CU-201: RS-232C CU-221: USB (4) Connect the other end of the RS-232C/USB interface cable to the corresponding port of the host PC.
5.4.3 Interfacing with the Host PC This section describes how to start communication with the host PC from System Menu. The same may apply when you use a user program. (1) Turn the host PC on to run Windows. (2) CU-201: Plug the AC adapter into a wall socket. CU-221: Plug the AC adapter into a wall socket, if necessary. (3) Make sure that the BHT is turned off and then place it on the CU-200. (4) On the host PC, initiate a communications program that can use Ymodem.
Chapter 5 Handling the CU-200 (Option) 5.5 Charging the Rechargeable Battery Cartridge (using the CU-200) You can charge a rechargeable battery cartridge loaded in the BHT. Be sure to turn the BHT off before starting charging. Service Life of Rechargeable Battery Cartridge: Lithium-ion batteries used in the rechargeable battery cartridge will gradually deteriorate during the repeated cycles of charging and discharging due to its properties, even under normal use.
Charging Operation and LED Indication Operator's Action CU-200 Status On standby Charge LED on the BHT OFF ⇓ Place the BHT on the CU-200. Charging ⇓ ⇓ After approx. 3 hours (approx. 5.5 hours*) when the CU-201/221 is powered from the AC adapter Charging completed After approx. 9 hours (approx. 21 hours*) when the CU-221 is powered from the USB interface ⇓ ON (in red) ON (in green) ⇓ OFF Remove the BHT. On standby *For grip style BHTs with two battery cartridges loaded.
Chapter 5 Handling the CU-200 (Option) 5.6 Interface Specifications [ 1 ] Interface Connector and Pin Assignment CU-201 The CU-201 has an RS-232C interface port (Dsub-9P). RS-232C interface port (Dsub-9P) on the CU-201 Functions Signal Input/Output CU-201 External device Pin No.
[ 2 ] Interface Cable Connection CU-201 As illustrated below, connect the CU-201 (on which the BHT is put) to a host PC with a cross-mode cable. To connect it to a modem, use a straight-mode cable.
Appendix A. A.1 Specifications.................................................................................................................................................. 140 BHT-200Q/200QW................................................................................................................................................ 140 [1] Product Specifications ......................................................................................................................................
Appendix A. Specifications A.1 BHT-200Q/200QW [ 1 ] Product Specifications Power Source Main power Rechargeable lithium-ion battery cartridge (3.7 VDC) Dimensions (W) x (L) x (H) Weight Regular style BHT 90 x 186 x 60 mm (3.5 x 7.3 x 2.4 inches) Grip style BHT 90 x 186 x 175 mm (3.5 x 7.3 x 6.9 inches) Regular style BHT Approx. 390 g (Approx. 13.8 oz.) including battery cartridge Grip style BHT Approx. 470 g (Approx. 16.6 oz.
Appendices [ 2 ] Readable Code Specifications The values given below are based on the scanning reference position shown in the next item [ 3 ]. (1) QR Codes (Model 1 and Model 2) and MicroQR Code size Cell pitch QR code 21 x 21 cells to 113 x 113 cells (Skew angle: 360°) 0.25 mm (9.8 mils) 21 x 21 cells to 85 x 85 cells (Skew angle: 360°) 125 x 125 cells 0.33 mm (13.0 mils) Micro QR code 0.25 mm (9.
(6) Bar Codes Bar code type Bar dimensions Readable magnification Universal product codes EAN-13 EAN-8 UPC-A UPC-E EAN-13 with add-on EAN-8 with add-on 0.26 mm min. (10.24 mils min.) 0.8 min. UPC-A with add-on UPC-E with add-on 2-digits add-on 5-digits add-on Interleaved 2of5 (ITF) Codabar (NW-7) 2 to 46 digits 0.15 mm min. (5.91 mils min.
Appendices [ 3 ] Scanning Performance Scanning reference position As illustrated at left, align the reading window with the center of the label (code) to be scanned. 105 mm (4.1") Label Scanning distance and area QR codes Cell pitch Scanning distance 0.25 mm (9.8 mils) 40 to 130 mm (1.6 to 5.1 inches)* 0.33 mm (13.0 mils) 30 to 200 mm (1.2 to 7.9 inches)*1 0.50 mm (19.7 mils) 30 to 300 mm (1.2 to 11.8 inches)*2 1 PCS value: 0.9 min., Reflection intensity: 85% min.
Bar codes Module size Scanning distance 0.15 mm (5.9 mils) 60 to 115 mm (2.4 to 4.5 inches)*3 0.25 mm (9.8 mils) 40 to 220 mm (1.6 to 8.7 inches)*4 0.33 mm (13.0 mils) 40 to 275 mm (1.6 to 10.8 inches)*5 PCS value: 0.9 min., Reflection intensity: 85% min. for white The BHT-200Q/200QW may fail to read codes due to specular reflection depending upon the position of the light source, scanning angle of the reading window, and other conditions.
Appendices [ 4 ] Interface Specifications IrDA Interface Synchronization: Start-stop Input signals: RD Output signals: SD Transmission speed: 115,200 bps max. USB Interface Specification: USB1.1 Device, Full-speed compliant Connector: Mini - B receptacle Pin assignment: See below. Pin 1 Pin 5 Pin No. 1 2 3 4 5 Signal name VBUS DD+ No connection GND Radio Interface Frequency: 2.4 GHz band Transmission speed: 11/5.
A.2 CU-200 [ 1 ] Product Specifications Power Source Power Consumption (AC adapter output) Dimensions (W) x (L) x (H) CU-201 CU-221 100 to 240 VAC, 50/60 Hz, 0.2 A (via the dedicated AC adapter) Via the USB interface* 5 VDC, 1500 mA 5 VDC, 500 mA 114 x 140 x 87 mm (4.49 x 5.51 x 3.43 inches) 114 x 134 x 87 mm (4.49 x 5.28 x 3.43 inches) Approx. 210 g (Approx. 7.41 oz.
Appendices [ 3 ] Interface Specifications CU-201 RS-232C interface port (Dsub-9P) on the CU-201 Functions Signal Input/Output CU-201 External device Pin No. Signal 2 RD Receive data ← 3 SD Send data → 4 ER Data terminal equipment ready → 5 SG Signal ground ― 6 DR Data set ready ― 7 RS Request to send ― 8 CS Ready to send ― Shown below is a diagram of the internal connection in the CU-201. CU-201 BHT CU-221 The CU-221 has a Full-Speed USB 1.
Appendix B. Loading an Optional Compact Flash Card Load an optional Compact Flash card to the BHT using the following procedure. (1) Turn the BHT upside down. (2) Slide the right and left release buttons in the direction of the arrows to remove the battery cartridge cover. Release button Battery cartridge cover Release button (3) Pull up the battery pull strap to remove the battery cartridge.
Appendices (4) Pull the lock of the inside cover to the right and towards you to release it. Inside cover Lock Lock Inside cover (5) Insert a Compact Flash card into the slot with the connector facing the slot and with the top facing down.
To remove the Compact Flash card, press the card release button provided at the left of the card as shown below. Compact Flash card Card release button (6) Set the inside cover so that its lock and pawl become fitted between the printed circuit boards.
Appendices (7) Push the battery cartridge into the BHT. The end of the battery pull strap should come out from the left edge of the battery cartridge. Battery cartridge Battery pull strap (8) Set the battery cartridge cover back into place and return the right and left release buttons to the original position.
Appendix C. Quality Assurance Standards Applicable Standards EMC Standard Radio Standard Country or Region Name of Regulation United States FCC Canada IC United States FCC** Canada IC** Laser Radiation Standard * Standard(s) Condition* Remark FCC Part 15 Subpart B Class A ICES-003 Issue No.4 Class A FCC Part 15 Subpart C --- RSS-210 --- IEC 60825-1:1993+A2:2001*** Class 2 : meet this standard ** This regulation applies to the built-in radio communication module only.
BHT-200Q/200QW User's Manual First Edition, July 2004 DENSO WAVE INCORPORATED The purpose of this manual is to provide accurate information in the handling and operating of the BHT-200Q/200QW. Please feel free to send your comments regarding any errors or omissions you may have found, or any suggestions you may have for generally improving the manual. In no event will DENSO WAVE be liable for any direct or indirect damages resulting from the application of the information in this manual.
