User's Manual
Copyright © DENSO, 2001 All rights reserved. No part of this publication may be reproduced in any form or by any means without permission in writing from the publisher. Specifications are subject to change without prior notice. All products and company names mentioned in this manual are trademarks or registered trademarks of their respective holders.
Preface Please READ through these operating instructions carefully. It will enable you to operate your BHT-100Q/100B correctly. After you have finished reading the instructions, keep this manual handy for speedy reference.
How this book is organized This manual is made up of five chapters and appendices. Chapter 1. Quick Guide Describes the basic operating method of the BHT and the related notes. Chapter 2. Getting Started the BHT and System Mode Summarizes the BHT system configuration and describes the operation including preparation and System Mode (which is required for the efficient use of application programs). Chapter 3.
■ Technical Terms Used in This Manual Source Program and Object Program (User Program) Generally, a source program is translated into an object program by a compiler. This manual calls an object program a user program. BHT-BASIC This manual expresses BHT-BASIC3.0 and BHT-BASIC3.5 as BHT-BASIC.
SAFETY PRECAUTIONS Be sure to observe all these safety precautions. ■ Please READ through this manual carefully. It will enable you to use the BHT and CU correctly. ■ Always keep this manual nearby for speedy reference. Strict observance of these warning and caution indications are a MUST for preventing accidents which could result in bodily injury and substantial property damage.
WARNING Handling the battery cartridge • Never disassemble or heat the battery cartridge, nor put it into fire or water; doing so could cause battery-rupture or leakage of battery fluid, resulting in a fire or bodily injury. Never put me into fire! • Do not carry or store the battery cartridge together with metallic ball-point pens, necklaces, coins, hairpins, etc.
WARNING • Do not look into the light source through the reading window or point the light source towards the eyes. The light emitted through the reading window is harmful to the eyes. • Do not poke at the eyes with the stylus that comes with the BHT. Handling the CU • If smoke, abnormal odors or noises come from the CU, immediately unplug the AC adapter from the wall socket and contact your nearest dealer. Failure to do so could cause fire or electrical shock.
CAUTION Basic handling tips I'm burning up! • Never put the BHT in places where there are excessively high temperatures, such as inside closed-up automobiles, or in places exposed to direct sunlight. Doing so could affect the housing or parts, resulting in a fire. • Avoid using the BHT in extremely humid or dusty areas, or where there are drastic temperature changes. This humidity is killing me! Moisture or dust will get into the BHT, resulting in malfunction, fire or electrical shock.
CAUTION • If you drop the BHT so as to damage its housing, immediately turn off the power, pull out the rechargeable battery cartridge or dry battery cartridge, and contact your nearest dealer. Do not drop me! Failure to do so could cause smoke or fire. • For those machines using the dry battery cartridge, do not mistake the plus and minus marks when loading dry cells into the cartridge.
CAUTION • Never cover or wrap up the CU or AC adapter in a cloth or blanket. Doing so could cause the unit to heat up inside, deforming its housing, resulting in a fire. Always use the CU and AC adapter in a well-ventilated area. • Do not place the CU anyplace where it may be subjected to oily smoke or steam, e.g., near a cooking range or humidifier. Doing so could result in a fire or electrical shock. • Keep the power cord away from any heating equipment.
■ Proper Care of the BHT and CU Clean the housings, battery cartridge terminals, and CU-7001 charge terminals with a dry, soft cloth. Before cleaning, be sure to turn the BHT power off and unplug the AC adapter of the CU. • • • • Never use benzene, alcohol, or other organic solvents. The housing may be marred or the paint may come off. Never rub or strike the liquid crystal display (LCD) with anything hard. The LCD surface will be easily scratched or broken.
FCC Regulations This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Content Overviews Preface ................................................................................................................................. i How this book is organized .............................................................................................. ii SAFETY PRECAUTIONS ..................................................................................................... iv Chapter 1 1.1 Quick Guide ..............................................................................
3.4 Communications Protocols ...................................................................................... 116 3.4.1 BHT-protocol ...................................................................................................... 116 3.4.2 BHT-Ir Protocol .................................................................................................. 122 Chapter 4 Error Messages ............................................................................................ 128 4.
Chapter 1. Quick Guide Chapter 2. Getting Started the BHT and System Mode Chapter 3. Communications Operations of the BHT Chapter 4. Error Messages Chapter 5.
Chapter 1. Quick Guide Chapter 1 Quick Guide This chapter describes the basic operating method of the BHT and the related notes. 1.1 Reading 2D Codes and Bar Codes ............................................................................ 2 BHT-100Q .................................................................................................................... 2 BHT-100B .................................................................................................................... 4 1.
1.1 Reading 2D Codes and Bar Codes BHT-100Q Turn the BHT power on, bring the reading window to the target code, and press the trigger switch. The BHT-100Q turns three marker LEDs on to indicate the scanning range and the illumination LED to scan the code. Keep the BHT stationary in a position where the target code lies between the right and left markers and the center marker comes to the center of the target code. Hold the reading window 4 to 14 cm (1.6 to 5.5 inches) away from codes to be scanned.
Chapter 1. Quick Guide • Before reading 2D codes or bar codes, clean those labels if stained. • Avoid using the BHT in direct sunlight. The BHT might fail to read correctly. • To read 2D codes or bar codes on curved surfaces, apply the BHT to the target code so that the code comes to the center of the scanning range indicated by the markers. • Depending upon the code size or cell pitch, the proper scanning distance from 2D codes or bar codes will differ.
BHT-100B Turn the BHT power on, bring the bar-code reading window to the bar code to be scanned, and press the trigger switch. The BHT-100B emits a laser light to indicate the scanning range and turns on the illumination LED to scan the bar code. When the BHT has read the bar code successfully, the indicator LED will illuminate in green. Bar code scanning range covered by the laser light Max. 40 cm (15.7")* Indicator LED Illuminates in green when the BHT has successfully read the code.
Chapter 1. Quick Guide • Before reading bar codes, clean those labels if stained. • Avoid using the BHT in direct sunlight. The BHT might fail to read correctly. • To read bar codes on curved surfaces, apply the BHT to the target bar code so that the code comes to the center of the scanning range indicated by the laser beam. • When you pull the bar-code reading window away from bar codes, the actual scanning range will become narrower than the range covered by the laser beam.
1.2 Setting and Using the Hand Strap and Stylus ■ Setting the hand strap Hand strap ■ Using the hand strap Put your hand through the hand strap and hold the BHT as shown below. This will prevent you from dropping the BHT accidentally.
Chapter 1. Quick Guide ■ Setting the stylus Hand strap Stylus ■ Using the stylus The BHT has a touch screen LCD that enables you to use touch keys and draw images on the touch screen with the stylus if you have defined those touch keys and graphics pad box in user programs, respectively. Before using the touch screen, adjust it, referring to Subsection 2.3.3. Press the touch screen only with the stylus that comes with the BHT.
1.3 Setting the Backlight Pressing the right-hand trigger switch (M4 key) while holding down the SF (Shift) key activates or deactivates the backlight function. Backlight OFF (The backlight function is OFF when you turn the BHT power on.) Press the right-hand trigger switch while holding down SF.
Chapter 1. Quick Guide 1.4 Using the Keypad ■ Entering Numerical Data To enter numerical data, e.g., the quantity of goods, use the ten numerical keys and the ENT key. For example, to enter the number "120," press the 1, 2 and 0 keys and then press the ENT key. If you key in any wrong value, press the C or BS key and then enter the correct one. ■ Selecting Tasks If the LCD shows the selection items (xxx) prefixed by numerals (e.g.
1.5 Transferring Data ■ Using infrared link Using infrared rays, the BHT may transfer data directly to the host computer equipped with an IrDA interface port and other IrDA-compliant devices. • Make sure that there is no obstruction in the light path between the BHT and any target stations. In infrared communication, you need to keep the BHT and any target stations within the effective infrared radiation range, usually 10 to 80 cm (3.94 to 31.50").
Chapter 2. Getting Started the BHT and System Mode Chapter 2 Getting Started the BHT and System Mode This chapter summarizes the BHT system configuration and describes the operation including preparation and System Mode (which is required for the efficient use of application programs). 2.1 2.2 2.3 BHT System Configuration ..................................................................................... 12 Components and Functions ........................................................................
2.1 BHT System Configuration The BHT barcode data collection system requires the following hardware as well as the BHT Bar Code Handy Terminal (which reads 2D codes or bar codes and accepts key entry) as illustrated below: ● Host computer: Allows you to edit, manage and download programs and data, as well as downloading system programs. For host computers having no IrDA interface ports, the optional CU-7000 optical communications unit and RS-232C interface cable are available.
Chapter 2. Getting Started the BHT and System Mode ■ Host Computer Models: PC/AT, PS/2 Optional application programs and OSes OS MS-DOS Win3.1 Win95 Win98 WinNT3.5/4.0 Applications BHT-BASIC3.0 BHT-BASIC3.0 BHT-BASIC Compiler (MS-DOS–based) (Windows3.1based) MS-DOS– — Ir-Transfer Utility C based Ir-Transfer Utility E — — Transfer Utility MS-DOS– based Windows3.1– based Win2000 Professional BHT-BASIC3.
■ Ir-Transfer Utility C (option) Running on the host computer, this utility transfers files between the BHT and the host computer. For its file transfer control procedure, the utility uses the BHT-Ir protocol. (For the details about the BHT-Ir protocol, refer to Chapter 3, Subsection 3.4.2.) To transfer files under any of the following conditions, use Ir-Transfer Utility C: - At transmission speeds of 115200 or 57600 bps (This may be impossible depending upon the host computer type.
Chapter 2. Getting Started the BHT and System Mode Software Structure System Programs and JIS Level 1 & Level 2 fonts are resident in the system area and user area, respectively. To use extension programs and user programs, you should download the program files into the user area. To use data files (e.g., goods master files) required for execution of user programs, you should download those data files before execution of user programs. Those files will be stored in the user area.
System Mode System Mode is a system program exclusively designed for the effective use of user programs in the BHT. It sets up the execution environments for those programs; e.g., it prepares downloading/uploading conditions, sets the calendar clock, and tests the BHT components including the LCD, beeper, and keypad. Shown below is the System Mode menu (SYSTEM MENU). ■ JIS Level 1 and Level 2 Font Files These files contain font data required for displaying Kanji characters on the LCD.
Chapter 2. Getting Started the BHT and System Mode 2.2 Components and Functions Indicator LED Illuminates in green when the BHT has successfully read a code. Touch screen LCD (liquid crystal display) Shows the characters and graphic patterns. You may directly touch the display with the stylus for data entry. Trigger switch (M4 key) Press this switch to start code reading. Hand strap Be sure to put your hand through this strap to prevent you from dropping the BHT accidentally.
The functions of the keys may be set by user programs. Shown below is a set of sample functions. Status Indicators Battery voltage level Shows the current battery voltage level. Displays when the voltage level is high. Displays when the voltage level is low. Keypad shift state Displays when the keypad is shifted. Alphabet and touch screen input states Displays when the alphabet input function is activated. Displays when the touch screen is ready to accept entry. M1 Numerical keys Used for numerical input.
Chapter 2. Getting Started the BHT and System Mode 2.3 Preparation 2.3.1 Setting-up 1: Loading the Battery Cartridge Before the first use of the BHT, be sure to load the battery cartridge as shown below. The battery cartridge is not loaded in the BHT when shipped from the factory. (1) Charge the rechargeable battery cartridge. (Refer to Section 5.5.) To use the dry battery cartridge in the BHT, set two dry cells into the cartridge.
• Never charge the dry battery cartridge. • The BHT has an integrated backup power source which backs up the memory and calendar clock in the BHT when no battery cartridge is loaded or the voltage level of the battery cartridge drops below the specified level. The backup power source is automatically charged by the battery cartridge.
Chapter 2. Getting Started the BHT and System Mode ■ Low Battery Indication Low battery indication—Level 1 If the battery output voltage drops below a specified lower level limit while the BHT is in operation, the BHT displays the following Level 1 message for approx. 2 seconds and beeps three times. After that, it will resume previous regular operation. The battery recharge or replacement time will come soon.
• When replacing dry cells, always replace both of them with new alkaline manganese batteries (LR6). • You may charge the rechargeable battery cartridge with the optional CU-7001 communication unit or optional C-700/C-750 charger. For the charging procedure using the CU-7001, refer to Chapter 5. For that using the C-700/C-750, refer to the "C-700 User's Manual"/"C-750 User's Manual.
Chapter 2. Getting Started the BHT and System Mode 2.3.2 Setting-up 2: Setting the Calendar Clock Turn the BHT on by pressing the PW key. The following message will appear. In the following cases, the above message will appear. In such instances, it is necessary to set the date and time. (The indication "00/01/01 00:00" will differ depending upon the calendar clock state.) • The BHT is first turned on from the time of purchase.
2.3.3 Adjusting the LCD Contrast, Beeper Volume and Touch Screen, and Switching the Beeper & Vibrator While holding down the M1 key or right-hand trigger switch (M4), press the PW key. The main adjustment screen appears which differs depending upon the current state as shown below. After adjustment, press the ENT key or no keys for five seconds. The new settings will be registered and the main adjustment screen will disappear.
Chapter 2. Getting Started the BHT and System Mode Adjusting the LCD contrast You can adjust the LCD brightness to eight contrast levels. (1) Use the 1 key (or M1 or M2 key) to select the LCD CONTRAST line. (2) To decrease the contrast, press the M1 key with the SF key held down; to increase it, press the M2 key with the SF key held down. Switching the beeper & vibrator You may choose any of three ways—beeping only, vibrating only, or beeping & vibrating as a confirmation of completion of code reading.
Adjusting the touch screen At the first use of the touch screen or if the touch areas seem to deviate from the normal positions when in use, adjust the touch screen according to the steps given below. Use the 5 key (or M1 or M2 key) to select the CALIBRATION line, then press the ENT key. The screen shown at left will appear. Touch the center of the "+" with the stylus. The screen will switch to the following one. To cancel adjustment and return to the main adjustment screen, press the C key.
Chapter 2. Getting Started the BHT and System Mode Touch the center of the 4th "+." The adjustment will complete and the display will return to the main adjustment screen. If the adjustment is not completed normally, the screen shown at left will appear where you may choose retry or not. If you select "1:Yes" and press the ENT key, the display will return to the top screen of the touch screen adjustment sequence.
2.3.4 Battery Voltage Display The battery voltage level is always displayed on the status indicator line (bottom line). Battery voltage level Shows the current battery voltage level. Displays when the voltage level is high. Displays when the voltage level is low. Status Indicators The displayed battery level shows the terminal voltage of the battery, not how much power is left. The battery voltage level varies depending upon the operation of the BHT, so the displayed level also may vary.
Chapter 2. Getting Started the BHT and System Mode 2.3.5 Battery Replacement Notes ■ When is battery replacement needed? If the "Charge the battery!" or "Replace the batteries!" appears on the LCD, replace the rechargeable battery cartridge with a fully charged one or replace the dry cells with new ones, respectively.
(2) When turning the BHT on after storage with no battery cartridge loaded: Even after removal of the battery cartridge, the calendar clock will work with the backup power source for a while. If the calendar clock backup has stopped, loading the battery cartridge and turning the BHT on will display the following message, prompting you to set the current date and time. Set the calendar clock according to the procedure given in Subsection 2.3.2.
Chapter 2. Getting Started the BHT and System Mode 2.3.6 BHT Turning-off Notes [ 1 ] "Shutdown in progress" message When the BHT is turned off by pressing the PW key or by the auto power-off feature, it displays the following message and starts preparation for shutdown. When the above message is displayed, do not remove the battery cartridge. If you do so and leave the BHT without a battery cartridge loaded for one hour or more, then the error message "Contact your administrator. Note the error number.
(1) (2) Press the 2 key while holding down the SF key. The screen will switch to the following: [ 1 ] YES: Run Scandisk and start the System. [ 2 ] NO: Turn the BHT off. Choose either one with the numerical keys and press the ENT key.
Chapter 2. Getting Started the BHT and System Mode If Scandisk finds an invalid file(s), the following screen will appear. As long as an invalid file exits, that screen displays every time the BHT System is started up. (3) Press the ENT key to start up the BHT System. ■ Scandisk when the resume function is enabled If Scandisk runs when the resume function is enabled, the screen given below may appear.
[ 3 ] About "$$BRKLST.SYS" If Scandisk finds an invalid file(s), it will automatically create the "$$BRKLST.SYS" file. To check the contents of the file, upload the file in System Mode to the host computer. (Refer to Subsection 2.5.3, "[ 3 ] Uploading.") Contents of the "$$BRKLST.SYS" file Records (1) File name (2) Error factor + (Broken since the BHT has not been turned off normally) * (Broken due to any other causes) (3) Broken records e.g.
Chapter 2. Getting Started the BHT and System Mode 2.4 Initializing the BHT System Initializing the system will lose program files and data files stored in the user area and the system settings will revert to the factory defaults. You may delete font files by selecting the whole user area to be initialized. You need to initialize the system when: (1) you want to delete all of the program files and data files. (2) the following message appears. On the following pages is an initialization procedure.
(1) Selecting the memory area to be initialized Press the PW key while holding down the SF, M1 and 0 keys together. The screen shown at left will appear. To initialize the user area except for the font file area, press the ENT key. The screen switches to the SELECT MESSAGE display given in step (2). To initialize the whole user area including the font file area, press the 2 key while holding down the SF key. The "2:WHOLE USER AREA" item will appear.
Chapter 2. Getting Started the BHT and System Mode (3) Confirming the memory area selected for initialization Selecting the "USER AREA EXCEPT FONTS" in step (1) above will call up the confirmation screen shown at left. 1 Yes : Starts initialization. 2 No : Cancels initialization and turns the power off. Select a desired item by using the numerical keys, then press the ENT key. Pressing the C key will switch the screen back to the area selection screen.
(5) Completion of initialization Upon completion of the initialization, the BHT displays the screen shown at left for a second and turns itself off automatically. • Do not turn the BHT off until the above initialization completion screen appears. A too-early powering-off will interrupt initialization, requiring you to initialize the BHT again. • If the message "Contact your administrator. Note the error number. (2XXX)" appears although the initialization has completed, initialize the BHT again.
Chapter 2. Getting Started the BHT and System Mode 2.5 Operating in System Mode System Mode is an operating software exclusively designed for the effective use of the BHT, which includes various functions as shown on the following pages. 2.5.1 Starting System Mode To start up System Mode, turn the BHT power on while holding down the SF and 1 keys. This operation calls up the SYSTEM MENU on the LCD as shown below. The function selected is highlighted (white-on-black) with the cursor.
■ Structure of System Mode SYSTEM MENU ⇐ Press the PW key while holding down the SF and 1 keys. Program Execution Allows you to select a desired user program to be executed immediately. (Refer to Subsection 2.5.3, [ 1 ].) 1 and ENT keys Downloading Transfers user program files or data files from the host computer to the memory integrated in the BHT. Downloading between the BHTs is also possible. (Refer to Subsection 2.5.3, [ 2 ].
Chapter 2. Getting Started the BHT and System Mode Testing Used for the code reading test, memory test, beeper test, aging test, communications test, LCD indication test, indicator LED test, touch screen test, key-entry test, vibrator test, and file test. Shown at left is the BHT-100Q screen. The BHT-100B screen displays "1:BARCODE" instead of "1:QRCODE." (Refer to Subsection 2.5.3, [ 5 ].
In addition to the functions given on the previous pages, System Mode has these four functions: Deleting files, Downloading/uploading the BHT system parameter file, Setting the remote wakeup parameters, and Downloading/uploading the system message file. To call up these functions, press the 0, 3, 4 or 6 key, respectively, while holding down the SF key when the SYSTEM MENU is displayed. SYSTEM MENU ⇐ Press the PW key while holding down the SF and 1 keys.
Chapter 2. Getting Started the BHT and System Mode 2.5.2 Operating in System Mode Some functions in System Mode require several screens to be shifted, as shown in the example below. [ 1 ] Calling up the desired set screen First, select a desired item on the current screen by using the numerical key or the M1 and M2 keys so as to highlight the desired item. Press the ENT key to establish the selected item and proceed to the subsequent screen. To return to the preceding screen, press the C key.
[ 2 ] Selecting a desired setting First, select a desired item on the current screen by using the numerical key or the M1 and M2 keys so as to highlight the desired item. Next, while holding down the SF key, use the M1 and M2 keys to select a desired setting and then press the ENT key. The screen returns to the previous selection screen. Press 2 key or use M1 and M2 keys to select the desired set item. Use the SF+M1 and SF+M2 keys to select the desired setting.
Chapter 2. Getting Started the BHT and System Mode 2.5.3 Detailed Description of the Functions in System Mode [ 1 ] Program Execution Selecting "1:EXEC PROGRAM" on the SYSTEM MENU calls up the screen shown at left. If more than one program has been downloaded to the user area of the target memory, use the M1 and M2 keys to move the cursor to a target program, and then press the ENT key. To return to the SYSTEM MENU, press the C key.
⇓ In the example shown at left, 26 programs are downloaded. If no program file is downloaded, the message shown at left will appear. To return to the SYSTEM MENU, press the C key.
Chapter 2. Getting Started the BHT and System Mode [ 2 ] Downloading If you download a file having the same name as one already used in the user area of the target memory in the BHT, the newly downloaded file replaces the old one. Selecting "2: DOWNLOAD" on the SYSTEM MENU calls up the screen shown at left. 1 FILE : Downloads a user program file or data file to the user area of the BHT. 2 HT<-->HT COPY : Downloads all of the files, system parameters, and calendar clock data stored in the connected BHT.
Download screens With this screen displayed, the BHT waits for a file to be downloaded. If you select "2:HT<-->HT" on the DOWNLOAD menu, the "HT<-->HT" will appear in the center of the 2nd line. If you select "1:FILE," nothing will appear on the 2nd line. The screen at left shows that "1:FILE" has been selected.
Chapter 2. Getting Started the BHT and System Mode Upon completion of downloading, the number of received records becomes equal to the total number of records and the beeper beeps once. Press the C key to return to the DOWNLOAD menu. If the host computer downloads another new file (if the BHT receives an ENQ code) when this screen is displayed, the BHT starts receiving it. (Refer to the "Ir-Transfer Utility C Guide"/"Ir-Transfer Utility E Guide"/"Transfer Utility Guide.
■ Problem The current download will exceed the maximum of 80 files in the memory. ■ Solution Press the 2 key to return to the SYSTEM MENU. Delete unnecessary files in memory or decrease the number of files to be downloaded if you attempted to download more than one file. (Refer to Subsection 2.5.3, [ 7 ] and [ 2 ].) ■ Problem Downloading has failed. ■ Solution To retry downloading, press the 1 key. Pressing the 2 key returns to the SYSTEM MENU.
Chapter 2. Getting Started the BHT and System Mode [ 3 ] Uploading Selecting "3: UPLOAD" on the SYSTEM MENU calls up the screen shown at left. 1 ONE FILE : Uploads a user program file or data file stored in the memory. 2 ALL FILES : Uploads all user program files (object programs) and all data files stored in the memory. 3 HT<-->HT COPY : Uploads all of the files, system parameters, and calendar clock data stored in the BHT, to another BHT. This function enables copying between the BHTs.
If you select "1:ONE FILE" or "2:ALL FILES" on the UPLOAD menu when no files are stored in the memory, the message shown at left will appear. Pressing the C key returns to the UPLOAD menu. Upload screens If you select "1:ONE FILE" and choose a file to be uploaded or if you select the "2:ALL FILES" or "3:HT<-->HT COPY" on the UPLOAD menu, then the screen shown at left will appear.
Chapter 2. Getting Started the BHT and System Mode Upon completion of uploading, the number of sent records becomes equal to the total number of records and the beeper beeps once. Press the C key to return to the UPLOAD menu. If you have selected "2:ALL FILES" or "3:HT<-->HT COPY" on the UPLOAD menu, a sequence of the above screens will be repeated by the number of files to be uploaded.
[ 4 ] System Environment Setting BHT-100Q Selecting "4: SET SYSTEM" on the SYSTEM MENU calls up the screen shown at left. 1 EXEC PROGRAM : Sets an execution program to be run when the power is turned on. 2 DISPLAY : Sets the message version (English or Japanese). 3 DATE/TIME : Sets the calendar clock (date and time).
Chapter 2. Getting Started the BHT and System Mode [4.1] Setting an execution program Selecting "1: EXEC PROGRAM" on the SET SYSTEM menu calls up the screen shown at left. Highlighted is the current setting. Use the M1 and M2 keys to move the cursor to a desired execution program to be run when the power is applied, and then press the ENT key. To return to the SET SYSTEM menu, press the C key. If no program files are stored in the memories, the screen shown at left will appear.
[4.2] Setting the message version Selecting "2: DISPLAY" on the SET SYSTEM menu calls up the screen shown at left. Highlighted is the current setting. 1 MESSAGE: Switches the message version to English or Japanese for system error messages and indications on the screen for the LCD contrast, beeper volume and touch screen adjustment and the beeper & vibrator switching. (The default is the message version that you selected in the initializing sequence.
Chapter 2. Getting Started the BHT and System Mode [4.3] Setting the calendar clock Selecting "3:DATE/TIME" on the SET SYSTEM menu calls up the screen shown at left. Use the numerical keys to enter the year (only the last two digits), month, day, hour, and minute in this order, and then press the ENT key. If the data is in one digit, add a 0 (zero) preceding the data. For the year, be sure to enter the last two digits of the year. For the hour, enter it in the 24-hour format.
[4.4] Setting the special scanning parameters BHT-100Q Selecting "4: QRCODE" on the SET SYSTEM menu calls up the screen shown at left. Highlighted is the current setting. 1 INVERT : Activates or deactivates the black-and-white inverted label reading function. 2 DECODE LEVEL : (Not applicable.) 3 MARKER : Sets the marker ON/OFF mode. 4 VIEW FINDER : Turns the view finder on or off. 5 OPTION DATA : Selects whether or not option data will be added to the tail of 2D code data read.
Chapter 2. Getting Started the BHT and System Mode Marker You may select the marker ON/OFF mode from the following: 0: Driven by the trigger switch 1: Fixed to ON 2: Fixed to OFF If you select "1" (Fixed to ON), the markers will keep ON so that power consumption is higher than that in other modes and the battery working time becomes short. Do not disturb this setting unless necessary.
• PDF417 Data read 1 2 3 Option data n-1 n n+1 n+2 "Y" Reserved 1 n+3 n+4 Error correction level n+5 n+6 No. of rows n+7 n+8 No. of digits Example: If a code read is "PDF417, Error correction level 4, 12 rows and 2 digits," then the option data below will follow. (Data read)… Y1041202 • MaxiCode Data read 1 2 3 n-1 n n+1 n+2 "X" Mode Example: If a code read is "MaxiCode and Mode 4," then the option data below will follow.
Chapter 2. Getting Started the BHT and System Mode BHT-100B Selecting "4: BARCODE" on the SET SYSTEM menu calls up the screen shown at left. Highlighted is the current setting. 1 INVERT : Activates or deactivates the black-and-white inverted label reading function. 2 DECODE LEVEL : Sets the decode level. 3 MARKER : Sets the marker ON/OFF mode. 4 ITF : Sets the minimum number of digits to be read for ITF. 5 STF : Sets the minimum number of digits to be read for STF.
Marker You may select the marker ON/OFF mode from the following: 0: Driven by the trigger switch 1: Fixed to ON 2: Fixed to OFF If you select "1" (Fixed to ON), the markers will keep ON so that power consumption is higher than that in other modes and the battery working time becomes short. Do not disturb this setting unless necessary. Minimum number of digits to be read for ITF, STF, or Codabar You may set the minimum number of digits to be read for ITF, STF, and Codabar.
Chapter 2. Getting Started the BHT and System Mode [4.5] Setting the communications environments After the BHT is initialized, the interface port and communications parameters are set as listed in the default table below. Do not access them unless necessary. Interface port Optical (Optical interface port) Communications protocol BHT-protocol Defaults Communications parameters for the optical interface port TRANSMIT SPEED 9600 bps PROTOCOL (Protocol options) SERIAL No.
Selecting the "5: COM" on the SET SYSTEM menu calls up the screen shown at left. 1 OPTICAL: Switches to the communications parameters setting screen for the optical interface. 2 CONNECTOR: Switches to the communications parameters setting screen for the direct-connect interface. 3 COM PORT: Switches to the interface port setting screen. 4 PROTOCOL TYPE: Switches to the communications protocol type setting screen.
Chapter 2. Getting Started the BHT and System Mode (1) Communications parameters setting screen Selecting "1:PARAMETER" on the SET OPTICAL screen calls up the screen shown at left. Highlighted is the current setting. Select the desired transmission speed by using the numerical keys or SF+M1 and SF+M2 keys, and then press the ENT key. To return to the SET OPTICAL screen, press the C key.
[4.5-2] Setting the communications parameters for the direct-connect interface Selecting "2:CONNECTOR" on the SET COM menu calls up the screen shown at left. 1 PARAMETER: Switches to the communications parameters setting screen. 2 PROTOCOL: Switches to the communications protocol option screen. Select a desired screen by using the numerical keys or M1 and M2 keys, and then press the ENT key. To return to the SET COM menu, press the C key.
Chapter 2. Getting Started the BHT and System Mode (2) Communications protocol option screen Selecting "2:PROTOCOL" on the SET CONNECTOR screen calls up the screen shown at left. Highlighted is the current setting. 1 SERIAL No.: Selects whether or not the system will add serial numbers to data blocks. 2 H. PARITY: Selects whether or not the system will add a horizontal parity. 3 LINKUP TIME: Selects the timeout length (in seconds) to be applied when a link is to be established.
[4.5-3] Setting the interface port Selecting the "3:COM PORT" on the SET COM menu calls up the screen shown at left. Highlighted is the current setting. 1 BASIC: Selects the optical or directconnect interface port to be used for user programs written in BHT-BASIC (OPEN "COM:"). 2 SYSTEM MODE: Selects the optical or directconnect interface port to be used for downloading or uploading files in System Mode.
Chapter 2. Getting Started the BHT and System Mode [4.5-4] Setting the communications protocol type Selecting the "4:PROTOCOL TYPE" on the SET COM menu calls up the screen shown at left. Highlighted is the current setting. 1 BHT Protocol: Selects the BHT-protocol for downloading or uploading files in System Mode or for the execution of XFILE statement in BHT-BASIC. This protocol should be selected for file transmission with Transfer Utility.
Selecting the "2:BHT-Ir Protocol" on the PROTOCOL TYPE screen calls up the screen shown at left. Enter the ID number of the BHT by using the numerical keys, and then press the ENT key. If you do not need to modify the current setting, press the ENT key only. An ID number should be five-digit decimal character string. The entry range is from 00001 to 65535. If the entry value is less than five digits, the ENT key will be deactivated.
Chapter 2. Getting Started the BHT and System Mode [4.6] Defining the functions of the shift key, magic keys, and function keys Selecting the "6:KEY" on the SET SYSTEM menu calls up the screen shown at left. Highlighted is the current setting. 1 SHIFT KEY: Switches to the shift key definition screen. 2 M1 KEY: Switches to the M1 key definition screen. 3 M2 KEY: Switches to the M2 key definition screen. 4 M3 KEY: Switches to the M3 key (left-hand trigger switch) definition screen.
Defining the function of M1, M2, M3 (left-hand trigger switch), or M4 (right-hand trigger switch) key Selecting the "2:M1 KEY," "3:M2 KEY," "4:M3 KEY" or "5:M4 KEY" on the SET KEY menu calls up the screen as shown at left. (This example appears when the "4:M3 KEY" is selected.) Highlighted is the current setting. The M1, M2, M3 or M4 key can function as listed below. 1 None: The key entry will be ignored. 2 Trigger Switch: As the trigger switch. 3 Shift Key: As the SF key.
Chapter 2. Getting Started the BHT and System Mode Enabling/disabling the function keys Selecting the "6:FUNC KEY" on the SET KEY menu calls up the screen shown at left. Highlighted is the current setting. 1 ALL OFF Disables all function keys. 2 F1-F4 ON Enables four function keys F1 through F4. 3 F1-F8 ON Enables all of the eight function keys F1 through F8. Select a desired setting by using the numerical keys or M1 and M2 keys, and then press the ENT key. The screen returns to the SET KEY menu.
[4.7] Setting the resume function Selecting "7: RESUME" on the SET SYSTEM menu calls up the screen shown at left. Highlighted is the current setting. 1 ON : Activates the resume function which resumes the current BHT status when the BHT power was turned off, when the BHT is switched on. 2 OFF : Deactivates the resume function. Select a desired item by using the numerical keys or M1 and M2 keys, and then press the ENT key. To return to the SET SYSTEM menu, press the C key.
Chapter 2. Getting Started the BHT and System Mode [ 5 ] Testing BHT-100Q Selecting "5:TEST" on the SYSTEM MENU calls up the screen shown at left. 1 QRCODE (BHT-100Q) : Selects the 2D-code & bar-code reading test. BARCODE : Selects the bar-code reading test. (BHT-100B) 2 MEMORY : Selects the RAM read/write test. BHT-100B 3 BEEPER : Selects the beeper scale test. 4 AGING : Selects the aging test. 5 COM : Selects the communications test.
[5.1] 2D-code and bar-code reading test BHT-100Q Selecting "1: QRCODE" on the TEST menu calls up the screen shown at left. Actually read bar codes with the BHT-100Q and check the read data displayed on the LCD. Bar-code type ⇓ Sample-1 Number of digits of the code Code type Data Upon completion of 2D-code & bar-code reading, the BHT-100Q beeps, turns on the indicator LED in green, and displays the read data together with the code type and the number of data digits.
Chapter 2. Getting Started the BHT and System Mode Listed below is a table showing the relationship between the 2D-code/bar-code types and the identifier letters to be displayed on the LCD. (Code 39 sample) Code Type QR Code ID Letters Q PDF417 Y MaxiCode X Data Matrix Z EAN-13, UPC-A A EAN-8 B UPC-E C Interleaved 2of5 (ITF)* I Codabar (NW-7)* N Code 39 M Code 128 K EAN-128 W * The minimum number of digits to be read depends on the scanning parameter setting. (Refer to [4.4].
BHT-100B Selecting "1: BARCODE" on the TEST menu calls up the screen shown at left. Actually read bar codes with the BHT-100B and check the read data displayed on the LCD. ⇓ Bar-code type Number of digits of the bar code Upon completion of bar-code reading, the BHT100B beeps, turns on the indicator LED in green, and displays the read data together with the barcode type and the number of data digits. To return to the TEST menu, press the C key.
Chapter 2. Getting Started the BHT and System Mode [5.2] Memory test Selecting "2:MEMORY" on the TEST menu calls up the screen shown at left, and then starts writing and reading onto/from all areas of the RAM as well as checking the address. XXXXX: Tested RAM capacity (in kilobytes) YYYYY: Total RAM capacity (in kilobytes) If any error is detected, the BHT beeps three times, shows the message as shown at left, and terminates the test. Where, zzzzzzzz : Address where an error has occurred.
[5.3] Beeper scale test Selecting "3:BEEPER" on the TEST menu calls up the screen shown at left and makes the beeper sound at three octaves listed below. Upon completion of this test, the BHT automatically returns to the TEST menu. To stop this test while in progress, turn the power off and on. Scale [5.
Chapter 2. Getting Started the BHT and System Mode [5.5] Communications test In System Mode, you may test the optical interface port and direct-connect interface port. ■ Preparation for the optical interface test Arrange two BHTs, one as a master station and the other as a slave station (to be tested) with their IR ports facing each other as illustrated below. In this test, the slave BHT transmits data to the master BHT and receives the data sent back from the master BHT.
Testing the optical interface port Selecting the "1:OPTICAL" on the TEST COM menu calls up the screen shown at left. At the slave BHT to be tested, select the "1:SLAVE" and at the master BHT, select the "2:MASTER." Then press the ENT key on each BHT. During the test, the screen shown at left is displayed. If any error occurs, the tested slave BHT beeps three times and shows the screen at left.
Chapter 2. Getting Started the BHT and System Mode Upon normal completion of the test, the tested slave BHT beeps once and shows the screen at left. Press the C key to return to the TEST COM menu. The master BHT will automatically return to the MASTER/SLAVE selection menu. Testing the direct-connect interface port Selecting the "2:CONNECTOR" on the TEST COM menu displays the screen shown at left and then starts testing the direct-connect interface port.
Upon normal completion of the test, the BHT beeps once and shows the screen at left. Press the C key to return to the TEST COM menu.
Chapter 2. Getting Started the BHT and System Mode [5.6] LCD, indicator LED, and touch screen tests In System Mode, you may test the LCD, indicator LED, and touch screen. . Selecting "6:LCD" on the TEST menu calls up the screen shown at left on the LCD. 1 LCD: Tests the LCD and indicator LED. 2 TOUCH SCREEN1: Tests touch-keys. 3 TOUCH SCREEN2: Tests the graphics pad box by drawing an image with the stylus. Select a desired item by using the numerical keys or M1 and M2 keys, then press the ENT key.
The checker pattern shown at left appears and the indicator LED goes off. BS key ⇑ ⇓ ENT key The checker pattern is reversed. BS key ⇑ ⇓ ENT key An outline with a width of one dot appears.
Chapter 2. Getting Started the BHT and System Mode The fine checker pattern appears. BS key ⇑ ⇓ ENT key The fine checker pattern is reversed. BS key ⇑ ⇓ ENT key Forty right-angled triangles appear.
BS key ⇑ ⇓ ENT key BS key ⇑ ⇓ ENT key Press the ENT key, and the BHT beeps once and returns to the TEST DISPLAY menu.
Chapter 2. Getting Started the BHT and System Mode Touch screen test 1 Selecting "2:TOUCH SCREEN1" on the TEST DISPLAY menu calls up the screen shown at left. Press individual touch-keys (■) on the LCD. When each of them is pressed, the beeper will sound and the key will become highlighted (■). Pressing the highlighted key again will cancel highlighting (■). Pressing all five touch-keys (highlighting all) or C key will return to the TEST DISPLAY menu.
[5.7] Key entry, beeper, and vibrator test Selecting "7:KEY & VIBRATION" on the TEST menu calls up the screen shown at left and makes the BHT ready for entry from the keypad. Pressing individual keys displays the identifier letters in the positions pre-assigned to those keys on the LCD as well as sounding the beeper or running the vibrator. (As long as the individual key is held down, the BHT continues beeping or vibrating.) Pressing the same key again erases the displayed letter.
Chapter 2. Getting Started the BHT and System Mode [5.8] File test Selecting "8:FILE" on the TEST menu calls up the screen shown at left. If any of the files stored in the memory is defective, an asterisk (*) or plus sign (+) will be prefixed to the defective file name(s). For details about the (*) and (+), refer to Subsection 2.3.6, [ 3 ]. Selecting a file on this screen will show the file size and the test result. To select a file, use the M1 and M2 keys to move the cursor to the desired file.
[ 6 ] System Information Selecting the "6:VERSION" on the SYSTEM MENU calls up the screen shown at left, displaying the system program version, memory sizes, system message version, and JIS font types and their versions. Press the C key to return to the SYSTEM MENU.
Chapter 2. Getting Started the BHT and System Mode [ 7 ] Deleting Files You may delete a program file or data file stored in the memory. File deletion menu Pressing the 0 key while holding down the SF key on the SYSTEM MENU calls up the screen shown at left. Use the M1 and M2 keys to move the cursor to the file to be deleted, then press the ENT key. Press the C key to return to the SYSTEM MENU. If no file is resident in the memory, the message shown at left appears.
When deletion is in progress, the screen shown at left is displayed. ⇓ Deletion completion screen Upon completion of deletion, the screen shown at left appears. Press the C key to return to the file deletion menu.
Chapter 2. Getting Started the BHT and System Mode [ 8 ] Downloading/Uploading the BHT System Parameter File The BHT system parameter file (named "_ _BHT.SYS") stores system environment settings specified in the SET SYSTEM menu (in Subsection 2.5.3, [ 4 ]) and other settings such as the LCD contrast and beeper volume. The SYSTEM PARAMETER transfer menu allows you to upload or download the BHT system parameter file to/from the host computer.
[8.1] Downloading the BHT system parameter file Selecting "1:DOWNLOAD" on the SYSTEM PARAMETER transfer menu calls up the screen shown at left. With this screen displayed, the BHT waits for the BHT system parameter file to be downloaded. ⇓ While the downloading operation is in progress, the screen shown at left is displayed indicating the file name and the number of received records/the total number of records. To abort the downloading operation, press the C key.
Chapter 2. Getting Started the BHT and System Mode If an error occurs during downloading If some error occurs during downloading, the BHT beeps three times and shows one of the following screens with the prompt "Retry?": To retry the download, press the 1 and ENT keys; to abort it, press the 2 and ENT keys. To return to the SYSTEM PARAMETER transfer menu, press the C key. ■ Problem The memory is insufficient for storing the BHT system parameter file to be downloaded.
■ Problem Downloading has failed. ■ Solution To retry downloading, press the 1 key. Pressing the 2 key returns to the SYSTEM MENU. Check the interface port, communications parameters, and communications protocol type in the SET SYSTEM menu or perform the communications test in the TEST menu. (Refer to Subsection 2.5.3, [4.5] and [5.5].) It is also necessary to check the communications parameters setup of the host computer. [8.
Chapter 2. Getting Started the BHT and System Mode ⇓ Upon completion of uploading, the BHT displays the screen shown at left and beeps once. Press the C key to return to the SYSTEM PARAMETER transfer menu. If an error occurs during uploading If some error occurs during uploading, one of the following screens will appear and the beeper beeps three times. To retry the uploading operation, press the 1 and ENT keys; to abort it, press the 2 and ENT keys.
■ Problem The memory has already contained 80 files, so the BHT system parameter file cannot be set up. ■ Solution Press the C key to return to the SYSTEM MENU, then delete unnecessary files in the memory. (Refer to Subsection 2.5.3, [ 7 ]. ■ Problem Uploading has failed. ■ Solution To retry uploading, press the 1 key. Pressing the 2 key returns to the SYSTEM MENU.
Chapter 2. Getting Started the BHT and System Mode [9] Setting the Remote Wakeup Pressing the 4 key while holding down the SF key on the SYSTEM MENU calls up the screen shown at left. 1 REMOTE WAKEUP: Activates or deactivates the remote wakeup function. 2 TRANSMIT SPEED: Sets the transmission speed for the remote wakeup. Select a desired item by using the numerical keys or M1 and M2 keys. Then select a desired setting by using the SF+M1 and SF+M2 keys. To return to the SYSTEM MENU, press the C key.
[ 10 ] Downloading/Uploading the System Message File The system message file (named "_ _SYSMSG.FN2") stores system messages, e.g., "Shutdown in progress. Do not remove the battery." and "Charge the battery!." The SYSTEM MESSAGE transfer menu allows you to upload or download the system message file to/from the host computer. If you select the "2:UPLOAD," the system will set up the system message file based on the current settings and upload it to the host computer.
Chapter 2. Getting Started the BHT and System Mode [10.1] Downloading the system message file Selecting "1:DOWNLOAD" on the SYSTEM MESSAGE transfer menu calls up the screen shown at left. With this screen displayed, the BHT waits for the system message file to be downloaded. ⇓ While the downloading operation is in progress, the screen shown at left is displayed indicating the file name and the number of received records/the total number of records. To abort the downloading operation, press the C key.
If an error occurs during downloading If some error occurs during downloading, the BHT beeps three times and shows one of the following screens with the prompt "Retry?": To retry the download, press the 1 and ENT keys; to abort it, press the 2 and ENT keys. To return to the SYSTEM MESSAGE transfer menu, press the C key. ■ Problem The memory is insufficient for storing the system message file to be downloaded.
Chapter 2. Getting Started the BHT and System Mode ■ Problem Downloading has failed. ■ Solution To retry downloading, press the 1 key. Pressing the 2 key returns to the SYSTEM MENU. Check the interface port, communications parameters, and communications protocol type in the SET SYSTEM menu or perform the communications test in the TEST menu. (Refer to Subsection 2.5.3, [4.5] and [5.5]. [13.
Upon completion of uploading, the BHT displays the screen shown at left and beeps once. Press the C key to return to the SYSTEM MESSAGE transfer menu. When the BHT uploads the system message file, it creates a temporary file named "_SYSMSG.FN3" in the user area. If the user area is insufficient for creating the temporary file, therefore, an error will result. The created temporary file will be automatically deleted after completion of uploading.
Chapter 2. Getting Started the BHT and System Mode ■ Problem The memory is insufficient for setting up the system message file. ■ Solution Press the C key to return to the SYSTEM MENU, then delete unnecessary files in the memory. (Refer to Subsection 2.5.3, [ 7 ]. ■ Problem The memory has already contained 80 files, so the BHT system message file cannot be set up. ■ Solution Press the C key to return to the SYSTEM MENU, then delete unnecessary files in the memory. (Refer to Subsection 2.5.3, [ 7 ].
Chapter 3 Communications Operations of the BHT-100Q/100B This chapter describes the communications operations of the BHT-100Q/100B—the IR communication, RS-232C interface specifications, the basic communications specifications, and the communications protocols—for data transfer with the host computer or other devices. 3.1 Infrared Communication ....................................................................................... 109 3.2 RS-232C Interface Specifications .................................
Chapter 3. Communications Operations of the BHT-100Q/100B 3.1 Infrared Communication The BHT has an integrated infrared (IR) communications device which enables wireless transfer of programs and data between the BHT and the host computer and between the BHTs, instead of the conventional wire transfer.
The BHT's IR communications device is IrDA-compliant. IrDA stands for Infrared Data Association, which has defined hardware (IrDA Serial Infrared Physical Layer Link) and communications protocols for IR communications. The BHT's physical layer complies with the IrDA1.0, with a maximum transfer distance of 0.8 m and maximum transmission rate of 115.2 kbits per second.
Chapter 3. Communications Operations of the BHT-100Q/100B 3.2 RS-232C Interface Specifications [ 1 ] Interface Connector and Pin Assignment The BHT has a direct-connect interface port which is connectable to the 3-pole mini stereo plug (ø2.5 mm or 0.1") and supports a subset of the RS-232C interface as shown below. Using a direct-connect interface cable having the mini stereo plugs makes it possible to connect the BHT to a host computer (or another BHT) directly without any routing through the CU-7000.
[ 2 ] Interface Cable Connection Connect the BHT directly to a host computer, a modem, or a printer with a directconnect interface cable as illustrated below.
Chapter 3. Communications Operations of the BHT-100Q/100B 3.3 Basic Communications Specifications and Parameters 3.3.1 Basic Communications Specifications Listed below are the communications specifications when the BHT exchanges data with a host computer through the CU-7000 (optical interface) or direct-connect interface cable.
■ Transmission Code and Bit Order All characters should be coded to 7- or 8-bit code for data transmission. The standard data exchange code of the BHT is JIS 7- or 8-bit code. The transmission bit order is LSB (Least significant bit) first. What follows is an example for transmitting character A (41h, 01000001b) coded to JIS 8-level code with an even parity and a single bit each for start and stop bits.
Chapter 3. Communications Operations of the BHT-100Q/100B 3.3.2 Communications Parameters In System Mode and user programs written in BHT-BASIC, you may set the communications parameters listed below.
3.4 Communications Protocols The BHT supports both the BHT-protocol and the BHT-Ir protocol for file transmission. 3.4.1 BHT-protocol [ 1 ] Overview The BHT-protocol is the communications procedure used to transmit files between the BHT and a host (or between the BHTs). It adopts the response method using ACK/NAK codes.
Chapter 3. Communications Operations of the BHT-100Q/100B [ 2 ] Control Characters The control characters are classified into two groups: transmission control characters and text control characters. (1) Transmission control characters The transmission control characters listed below are used to compose transmission control sequences in phases 1 through 3. Symbol Value Meaning Function EOT 04h End Of Transmission Releases a data link (Phase 3). Requests abort of transmission (Phase 2).
(2) Text control characters The text control characters are used to format transmission texts. In the BHT-protocol, they include the following headers and a terminator. Symbol Value Meaning Function SOH 01h Start Of Heading Indicates the start of heading text (Phase 2). STX 02h Start of Text Indicates the start of data text (Phase 2). ETX 03h End of Text Indicates the end of data text (Phase 2). You may designate values of headers and a terminator with the protocol functions in BHT-BASIC.
Chapter 3. Communications Operations of the BHT-100Q/100B [ 3 ] Basic Format of Transmission Messages Basically, the BHT transmits data as units of a file. First, it transmits a heading text which includes the attribute information of a file (e.g., file name and the number of data texts) to be transmitted. Following the heading text, it transmits the data text in the file. A heading text and data text comprise a text.
[ 4 ] Text Format Text should be formatted according to the standard of the BHT-protocol before transmission. Shown below are two types of the standard text formats for program files and data files. ■ Program Text Format (1) Heading text Byte position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Number of data texts contained (5 bytes) Program file name (12 bytes) Example of contents P R O G 1 .
Chapter 3. Communications Operations of the BHT-100Q/100B ■ Data Text Format (1) Heading text Byte position Number of fields (2 bytes) Length of data field 1 Length of data field n (2 bytes) (2 bytes) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Number of data texts contained (5 bytes) Data file name (12 bytes) Example of contents M A S T E R . D A T n 0 0 5 9 2 The data file name should be a maximum of 12 characters in length and it consists of FILE NAME and .EXTENSION.
3.4.2 BHT-Ir Protocol [ 1 ] Overview The BHT-Ir protocol is the communications procedure for the serial infrared link, which is used to transmit files between the BHT and a host (or between the BHTs). It adopts the response method using ACK/NAK codes. The BHT-Ir protocol can be used also for communications through the direct-connect interface.
Chapter 3. Communications Operations of the BHT-100Q/100B [ 2 ] Control Characters The control characters are classified into two groups: transmission control characters and text control characters. (1) Transmission control characters The transmission control characters listed below are used to compose transmission control sequences in phases 1 through 3. Symbol Value Meaning Function DLE EOT 1004h End Of Transmission Releases a data link (Phase 3). Requests abort of transmission (Phase 2).
(2) Text control characters The text control characters are used to format transmission texts. In the BHT-Ir protocol, they include the following headers and a terminator. Symbol Value Meaning Function DLE SOH 1001h Start Of Heading Indicates the start of heading text (Phase 2). DLE STX 1002h Start of Text Indicates the start of data text (Phase 2). DLE ETX 1003h End of Text Indicates the end of data text (Phase 2).
Chapter 3. Communications Operations of the BHT-100Q/100B [ 3 ] Basic Format of Transmission Messages Basically, the BHT transmits data as units of a file. First, it transmits a heading text which includes the attribute information of a file (e.g., file name and the number of data texts) to be transmitted. Following the heading text, it transmits the data text in the file. A heading text and data text comprise a text.
[ 4 ] Text Format Text should be formatted according to the standard of the BHT-Ir protocol before transmission. Shown below are two types of the standard text formats for program files and data files. ■ Program Text Format (1) Heading text Byte position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Number of data texts contained (5 bytes) Program file name (12 bytes) Example of contents P R O G 1 .
Chapter 3. Communications Operations of the BHT-100Q/100B ■ Data Text Format (1) Heading text Number of fields (2 bytes) Length of data field 1 (3 bytes) Byte position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Number of data texts contained (5 bytes) Data file name (12 bytes) Example of contents M A S T E R . Length of data field n (3 bytes) D A T 0 0 5 9 2 n The number of data texts should be 0 to 32767.
This chapter lists the error messages which will appear on the LCD if some error occurs in the BHT-100Q/100B. 4.1 System Errors ........................................................................................................ 129 4.2 Errors in System Mode .........................................................................................
Chapter 4. Error Messages 4.1 System Errors If some error occurs when the power is turned on or during program execution, one of the following error messages will appear on the LCD. System Program error ■ Problem A System Program error has occurred. If this error occurs, the BHT beeps five times (for 0.1 second per beep) and then turns itself off. ■ Solution Contact your nearest dealer.
Low battery indication—Level 2 (When the rechargeable battery cartridge is loaded) ■ Problem When the power is turned on or off or during execution of program (System Mode or application), the battery output level has lowered. If lower battery is detected, the BHT beeps five times (for 0.1 second per beep) and then turns itself off. Depending upon the battery level, the beeper may not sound five times. ■ Solution If the BHT is loaded with the rechargeable battery cartridge, replace or charge it.
Chapter 4. Error Messages Abnormally turned off last ■ Problem After turned off abnormally*, the BHT had been left with no battery cartridge loaded or with a discharged battery cartridge loaded, so unsaved data was lost. (*"Normally turned off" refers to turned-off with the PW key or by the auto power-off feature.) ■ Solution Refer to Subsection 2.3.6 "BHT Turning-off Notes.
Execution program not selected ■ Problem No user program has been selected as an execution program to be run when the power is turned on. If this error occurs, the BHT beeps five times (for 0.1 second per beep) and then turns itself off. ■ Solution Run System Mode and select an execution program in the SET SYSTEM menu. (For the selecting procedure, refer to Chapter 2, Subsection 2.5.3, [4.1].
Chapter 4. Error Messages System down error ■ Problem An error has occurred during execution of System Program. If this error occurs, the BHT beeps five times (for 0.1 second per beep). ■ Solution Unload and reload the battery cartridge, then turn on the power. If this error occurs frequently, make a note of the message and codes on the LCD and contact your nearest dealer.
4.2 Errors in System Mode If some error occurs during operation in System Mode, one of the following error messages will appear on the LCD. When selecting a program file or data file ■ Problem You attempted to execute a user program in the EXECUTE PROGRAM menu, but no user program files had been stored in the memory. ■ Solution Press the C key to return to the SYSTEM MENU screen, then download user programs. (Refer to Chapter 2, Subsection 2.5.3, [ 2 ].
Chapter 4. Error Messages ■ Problem You have deleted all of the files stored in the memory in the DELETE FILE menu. ■ Solution Press the C key to return to the SYSTEM MENU screen. During downloading of a program file, data file, BHT system parameter file, or system message file ■ Problem The memory is insufficient for storing files to be downloaded. ■ Solution Press the 2 key to return to the SYSTEM MENU, then delete unnecessary files in the memory or decrease the size of the file to be downloaded.
■ Problem The current download will exceed the maximum of 80 files in the memory. ■ Solution Press the 2 key to return to the SYSTEM MENU, then delete unnecessary files in the memory (or decrease the number of files to be downloaded if you attempted to download more than one file in the DOWNLOAD menu.) (Refer to Chapter 2, Subsection 2.5.3, [ 7 ], [ 2 ], [ 8 ], and [ 10 ].) ■ Problem Downloading has failed. ■ Solution To retry downloading, press the 1 key. Pressing the 2 key returns to the SYSTEM MENU.
Chapter 4. Error Messages ■ Problem You attempted to download an invalid program file. ■ Solution Check whether the program file you attempted to download is available to your BHT model. If it is not available, download the appropriate program. During uploading of a program file, data file, BHT system parameter file, or system message file ■ Problem The file you attempted to upload is damaged. ■ Solution To upload the damaged file as is, press the 1 key.
■ Problem The memory has already contained 80 files, so the BHT system parameter file or system message file cannot be set up. ■ Solution Press the C key to return to the SYSTEM MENU and delete unnecessary files. (Refer to Chapter 2, Subsection 2.5.3, [ 7 ].) ■ Problem Uploading has failed. ■ Solution To retry uploading, press the 1 key. Pressing the 2 key returns to the SYSTEM MENU.
Chapter 5. Handling the CU-7000 (Option) This chapter describes the handling procedure of the CU-7000, the interfacing with the host computer, and the charging of the rechargeable battery cartridge. 5.1 Functions of the CU-7000 ...................................................................................... 140 5.2 Components and Functions .................................................................................. 140 5.3 Applying Power to the CU-7000 ....................................
5.1 Functions of the CU-7000 The optical communications unit CU-7000 is available in two models: CU-7001 and CU7002. The CU-7001 has both of functions (1) and (2) given below, the CU-7002 has only function (1). (1) Data exchange function The CU-7001/CU-7002 exchanges data and programs between the BHT and the host computer. It interfaces with the BHT via the optical interface and with the host computer via the RS-232C interface.
Chapter 5. Handling the CU-7000 (Option) 5.3 Applying Power to the CU-7000 Apply power to the CU-7000 by connecting it to the wall socket via the dedicated AC adapter. Connect the outlet plug of the AC adapter to the power inlet connector of the CU-7000, then plug the other end of the AC adapter into the wall socket. AC adapter Power inlet connector WARNING • If smoke, abnormal odors or noises come from the CU, immediately unplug the AC adapter from the wall socket and contact your nearest dealer.
5.4 Communicating with the Host Computer 5.4.1 Setting the Transmission Speed of the CU-7000 Set the transmission speed of the CU-7000 to the same value as that of the BHT and the host computer, by using the DIP switch provided on the bottom of the CU-7000. (1) Turn the CU-7000 upside down. (2) Remove the protection sheet of the DIP switch from the CU-7000. (3) Set the selectors of the DIP switch as shown below.
Chapter 5. Handling the CU-7000 (Option) 5.4.3 Interfacing with the Host Computer This section describes how to start communication with the host computer in System Mode. The same may apply when you use a user program. (1) Turn the host computer on. (2) Plug the AC adapter of the CU-7000 into the wall socket. (3) Make sure that the BHT is turned off, then set it on the CU-7000. (4) Turn the BHT power on and run System Mode.
5.5 Charging the Rechargeable Battery Cartridge (using the CU-7001) You may charge a rechargeable battery cartridge loaded in the BHT. Service Life of Rechargeable Battery Cartridge: Lithium-ion batteries used in the rechargeable battery cartridge will gradually deteriorate during the repeated cycles of charging and discharging due to its properties, even under normal use.
Chapter 5. Handling the CU-7000 (Option) ■ Charging Operation and LED Indication Operator's Action CU-7001 Status On standby Indicator LED on the BHT OFF ⇓ Place the BHT on the CU-7001. Normal charging ⇓ ⇓ After approx. 4 hours Charging completed ⇓ ⇓ Remove the BHT.
5.6 RS-232C Interface Specifications [ 1 ] Interface Connector and Pin Assignment The CU-7000 has an RS-232C interface port (Dsub-25S). 13 1 25 14 RS-232C interface port (Dsub-25S) on the CU-7000 Pin No.
Chapter 5. Handling the CU-7000 (Option) [ 2 ] Interface Cable Connection As illustrated below, connect the CU-7000 (on which the BHT is put) to a host computer with a cross-mode cable. To connect it to a modem, use a straight-mode cable.
Appendix A. Specifications .............................................................................................. 149 A.1 A.2 BHT-100Q ........................................................................................................ 149 [1] Product Specifications ............................................................................ 149 [2] Readable Codes ....................................................................................... 151 [3] Scanning Performance .........
Appendices Appendix A. Specifications A.1 BHT-100Q [ 1 ] Product Specifications Power Source Main power • Rechargeable lithium-ion battery cartridge (3.6 VDC) or • Dry battery cartridge (two alkaline manganese batteries LR6s) Dimensions (W) x (L) x (H) 67 x 198 x 29 mm (2.6 x 7.8 x 1.1 inches) Weight Approx. 280 g (Approx. 9.9 oz.
Display Type: Touch screen, dot-matrix, FSTN liquid crystal display (LCD) with backlight Formation: Character display 200 dots wide by 304 dots high Status display 200 dots wide by 16 dots high Screen mode Font size Single-byte ANK* mode Standard-size (12-dot) ANK Regular-size Double-width Double-height Quadruple-size 12 24 12 24 x x x x 12 12 24 24 16 x 25 8 x 25 16 x 12 8 x 12 Two-byte Kanji mode Standard-size (16-dot) Full-width Regular-size Double-width Double-height Quadruple-size 16
Appendices [ 2 ] Readable Codes The values given below are based on the scanning reference position shown in the next item [ 3 ]. (Skew angle: 360˚) (1) QR Codes (Model 1 and Model 2) and MicroQR Code size Cell pitch 21 x 21 cells to 85 x 85 cells 0.25 mm (9.8 mils) 21 x 21 cells to 61 x 61 cells (105 x 105 cells)*1 0.33 mm (13.0 mils) 11 x 11 cells to 17 x 17 cells*2 0.25 mm (9.8 mils) *1 Applies to Model 2. *2 Applies to MicroQR.
(4) Bar Codes Bar code type Universal product codes EAN-13 EAN-8 UPC-A UPC-E Bar dimensions Readable range 0.26 to 0.33 mm (10.24 to 12.99 mils) 0.26 to 0.46 mm (10.24 to 18.11 mils) 0.26 to 0.33 mm (10.24 to 12.99 mils) 0.26 to 0.56 mm (10.24 to 22.05 mils) 0.8 to 1.0 magnifications 0.8 to 1.4 magnifications 0.8 to 1.0 magnification 0.8 to 1.7 magnifications Interleaved 2of5 (ITF) 2 to 34 digits* Codabar (NW-7) 3 to 23 digits Code 39 0.15 mm min. (5.
Appendices [ 3 ] Scanning Performance ■ Scanning reference position As illustrated at left, align the reading window with the center of the label (code) to be scanned. BHT-100Q 90 mm (3.5") Label ■ Scanning distance and area Scanning distance 0 20 40 60 80 100 120 140 160 180 200 0.25 mm (9.8 mils) 0.33 mm (13.0 mils) 0.50 mm (19.7 mils) 119 x 89 (4.7 x 3.5) Scanning area: Width x height Cell pitch of QR codes supported within this range 0.15 mm (5.9 mils) 0.25 mm (9.8 mils) 0.33 mm (13.
PDF417 Module size Scanning distance 40 to 100 mm (1.6 to 3.9 inches)*3 40 to 170 mm (1.6 to 6.7 inches)*3 40 to 200 mm (1.6 to 7.9 inches)*3 0.17 mm (6.7 mils) 0.25 mm (9.8 mils) 0.33 mm (13.0 mils) PCS value: 0.9 min., Reflection intensity: 85% min. for white *3 Under these conditions: 1-column, 11-row, Row height: 3 modules, Error correction level: 1 MaxiCode Cell pitch Scanning distance 0.88 mm (34.6 mils) 45 to 230 mm (1.8 to 9.1 inches) PCS value: 0.9 min., Reflection intensity: 85% min.
Appendices [ 4 ] Interface Specifications Optical Interface Synchronization: Start-stop Input signals: RD Output signals: SD Transmission speed: 115,200 bps max. Direct-connect Interface Synchronization: Start-stop Transmission speed: 115,200 bps max. Signal level: Conforms to the RS-232C interface Pin assignment: As shown below. SD Pin No.
A.2 BHT-100B [ 1 ] Product Specifications Power Source Main power • Rechargeable lithium-ion battery cartridge (3.6 VDC) or • Dry battery cartridge (two alkaline manganese batteries LR6s) Dimensions (W) x (L) x (H) 67 x 198 x 29 mm (2.6 x 7.8 x 1.1 inches) Weight Approx. 280 g (Approx. 9.9 oz.) including battery cartridge Operating Ambient Temperature -5˚C to 50˚C (23˚F to 122˚F) Operating Humidity 20% to 80% (with no dew condensation) Ambient Illuminance 500 to 3000 x.
Appendices Display Screen mode Type: Touch screen, dot-matrix, FSTN liquid crystal display (LCD) with backlight Formation: Character display 200 dots wide by 304 dots high Status display 200 dots wide by 16 dots high Font size Dots (W x H) Chars x Lines Single-byte ANK* mode Standard-size (12-dot) ANK Normal-size Double-width Double-height Quadruple-size 12 24 12 24 x x x x 12 12 24 24 16 x 25 8 x 25 16 x 12 8 x 12 Two-byte Kanji mode Standard-size (16-dot) Full-width Normal-size Double
[ 2 ] Bar Code Specifications (1) Available Bar Code Types Bar code type Bar dimensions Readable magnification Universal product codes EAN-13 EAN-8 UPC-A UPC-E EAN-13 with supplemental codes 0.26 mm min. (10.24 mils min.) 0.8 min. EAN-8 with supplemental codes UPC-A with supplemental codes UPC-E with supplemental codes 2-digit add-on 5-digit add-on Interleaved 2of5 (ITF) Standard 2of5 (STF) Codabar (NW-7) 0.125 mm min. (4.92 mils min.) PCS value ≥ 0.
Appendices (3) Bar Code Label Size Recommended width: 10 mm min. (0.39 inch min.) Length: Depth of field (Distance from bar codes to the reading window) 400 mm (15.75 inches) Length of labels (including margins) 380 mm max. (14.96 inches max.) (Minimum narrow bar width: 1.0 mm min.)*4 Length Width (4) Thickness of Bars and Depth of Field Minimum narrow bar width 0.125 mm 0.15 mm 0.33 mm 1.0 mm 1.2 mm (4.92 mils) (5.91 mils) (12.99 mils) (39.37 mils) (47.
[ 3 ] Interface Specifications Optical Interface Synchronization: Start-stop Input signals: RD Output signals: SD Transmission speed: 115,200 bps max. Direct-connect Interface Synchronization: Start-stop Transmission speed: 115,200 bps max. Signal level: Conforms to the RS-232C interface Pin assignment: As shown below. SD Pin No.
Appendices A.3 CU-7000 [ 1 ] Product Specifications Power Source - Europe - U.S. -Australia 230 VAC, 16 VA 120 VAC, 13 VA 10 to 18 VDC, 450 mA (on 12 VDC) Power Consumption 8 VA max. Dimensions (W) x (L) x (H) 112 x 148 x 84 mm (4.41 x 5.83 x 3.31 inches) Weight CU-7001: Approx. 230 g (Approx. 8.11 oz.) CU-7002: Approx. 200 g (Approx. 7.06 oz.
[ 3 ] Interface Specifications 13 1 25 14 RS-232C Interface Port (Dsub-25S) on the CU-7000 Pin No. Signal 1 2 3 4 5 6 7 8 20 FG SD RD RS CS DR SG CD ER Signal Input/Output External CU-7000 device Functions Frame ground Send data Receive data Request to send Ready to send Data set ready Signal ground Carrier detect Data terminal equipment ready — → ← — — — — — — Shown below is a diagram of the internal connection in the CU-7000.
Appendices Appendix B. Communications Protocol Details B.1 BHT-protocol [ 1 ] Transmission Control Sequences Shown below is a typical message transmission sequence supported by the BHTprotocol. This sequence example does not include transmission errors or negative responses.
Data transmission may accidentally involve various types of errors. The BHT-protocol is designed to recover from those errors as frequently as possible. What follows is the BHT-protocol for phases 1 through 3. Phase 1: Establishment of Data Link ■ Normal phase 1 The sending station transmits an ENQ to the receiving station. Upon receipt of an ACK from the receiving station, the sending station shifts to phase 2. ENQ Sending station Receiving station ACK To phase 2.
Appendices ■ Abnormal termination of phase 1 (Abort of phase 1) If the sending station receives no ACK from the receiving station after sending an ENQ 10 times in succession, it sends an EOT to the receiving station after three seconds from the 10th ENQ to terminate the message transmission abnormally. Sending station Receiving station ENQ(1) 3 seconds ENQ(2) 3 seconds ENQ(3) ENQ(10) 3 seconds EOT Abnormal termination The receiving station's default timeout is 30 seconds.
Phase 2: Data Transmission ■ Normal phase 2 The sending station first sends a transmission block containing the heading text. Each time the sending station receives an ACK from the receiving station, it sends a transmission block containing the data texts as shown below. Upon receipt of an ACK in response to the last transmission block (data text n), the sending station shifts to phase 3. If a transmission message contains no data text, the sending station transmits the heading text only.
Appendices ■ Phase 2 with NAK If the sending station receives a NAK from the receiving station in response to a transmission block containing text data m, it sends that transmission block again immediately as shown below. If the sending station receives an ACK before receiving a NAK 10 times in succession, it continues the subsequent message transmission.
■ Phase 2 with EOT If the sending station receives an EOT anytime during phase 2, it shifts to phase 3 to terminate the message transmission abnormally. Even if phase 3 terminates normally, the transmission results in an abnormal end. Receiving station Sending station EOT Occurrence of an error To phase 3.
Appendices ■ Abnormal termination of phase 2 (Abort of phase 2) If the sending station receives no ACK from the receiving station after sending an ENQ nine times in succession, it sends an EOT to the receiving station after 3 seconds from the 9th ENQ to terminate this transmission sequence abnormally.
■ Phase 3 with iterated EOT transmission due to no response or invalid response If the sending station receives no response or any invalid response from the receiving station in response to an EOT sent, it iterates sending of an EOT at threesecond intervals up to ten times. If the sending station receives an ACK before sending an EOT ten times, it terminates the message transmission normally and releases the data link.
Appendices [ 2 ] Aborting Data Transmission Pressing the C key aborts data transmission. If the C key is pressed during downloading, the BHT transmits an EOT and aborts the file transmission. If it is pressed during uploading, the BHT transmits the current transmission block followed by EOT and then aborts the file transmission.
[ 3 ] BCC for Horizontal Parity Checking To check whether data has been transmitted accurately, the BHT supports horizontal parity checking for every transmission block. In horizontal parity checking, a horizontal parity byte so called BCC (Block Check Character) is suffixed to an ETX of every transmission block.
Appendices B.2 BHT-Ir protocol [ 1 ] Transmission Control Sequences Shown below is a typical message transmission sequence supported by the BHT-Ir protocol. This sequence example does not include transmission errors or negative responses.
Data transmission may accidentally involve various types of errors. The BHT-Ir protocol is designed to recover from those errors as frequently as possible. What follows is the BHT-Ir protocol for phases 1 through 3. Phase 1: Establishment of Data Link ■ Normal phase 1 The sending station transmits a sequence of DLE ENQ and IDm (sending station's ID) to the receiving station.
Appendices ■ Abnormal termination of phase 1 (Abort of phase 1) If the sending station receives no sequence of DLE ACK and IDs from the receiving station after sending a sequence of DLE ENQ and IDm 60 times in succession, it sends a sequence of DLE EOT and IDm to the receiving station after 0.5 second from the 60th sequence of DLE ENQ and IDm, then aborts the message transmission abnormally. Sending station Receiving station DLE ENQ and IDm (1) 0.5 second DLE ENQ and IDm (2) 0.
Phase 2: Data Transmission ■ Normal phase 2 The sending station first sends a transmission block containing the heading text. Each time the sending station receives a sequence of DLE ACK and IDs from the receiving station, it sends a transmission block containing the data texts as shown below. Upon receipt of a sequence of DLE ACK and IDs in response to the last transmission block (data text n), the sending station shifts to phase 3.
Appendices ■ Phase 2 with suspension of data reception for erasure of the flash memory If the receiving BHT requires the flash memory to be erased for receiving downloaded files, it sends a sequence of WACK and IDs to the sending station to suspend the data transmission. Upon receipt of the sequence of WACK and IDs, the sending station stops the data transmission until any response comes from the receiving station for one minute.
■ Phase 2 with a sequence of DLE NAK and IDs If the sending station receives a sequence of DLE NAK and IDs from the receiving station in response to a transmission block containing text data m, it sends that transmission block again immediately as shown below. If the sending station receives a sequence of DLE ACK and IDs before receiving the sequence of DLE NAK and IDs 10 times in succession, it continues the subsequent message transmission.
Appendices ■ Phase 2 with a sequence of DLE EOT and IDs If the sending station receives a sequence of DLE EOT and IDs anytime during phase 2, it shifts to phase 3 to terminate the message transmission abnormally. Even if phase 3 terminates normally, the transmission results in an abnormal end. Sending station Receiving station DLE EOT and IDs Occurrence of an error To phase 3.
■ Abnormal termination of phase 2 (Abort of phase 2) If the sending station receives no sequence of DLE ACK and IDs from the receiving station after sending a sequence of DLE ENQ and IDs 59 times in succession, it sends a sequence of DLE EOT and IDs to the receiving station after 0.5 second from the 59th sequence of DLE ENQ and IDs and then aborts this transmission abnormally. Sending station 0.5 second 0.5 second Receiving station DLE ENQ and IDs (1) DLE ENQ and IDs (2) DLE ENQ and IDs (59) 0.
Appendices ■ Phase 3 with iterated transmission of DLE EOT and IDs due to no re- sponse or invalid response If the sending station receives no response or any invalid response from the receiving station in response to the sent sequence of DLE EOT and IDs, it iterates sending of the sequence at 0.5-second intervals up to 60 times.
■ Phase 3 with timeout at the receiving station If the receiving station receives no subsequent text or normal sequence of DLE EOT and IDs within 30 seconds after sending a sequence of DLE ACK and IDs, it sends a sequence of DLE EOT and IDs and aborts the transmission abnormally. Sending station Data text #n Receiving station DLE ACK and IDs 30 seconds DLE EOT and IDs Abnormal termination [ 2 ] Aborting Data Transmission Pressing the C key aborts data transmission.
Appendices [ 3 ] CRC To check whether data has been transmitted accurately, the BHT-Ir protocol supports CRC (Cyclic Redundancy Check) which employs the CRC-16 generating system. In CRC, a CRC character is suffixed to a sequence of DLE ETX of every transmission block. Operands for CRC-16 The CRC generates CRC-16 from all bytes of a transmission block excluding DLE SOH or DLE STX characters (which are at the head of a transmission block), DLE character of DLE ETX and DLE character of DLE DLE in the text.
Appendix C. A Typical Basic Operation What follows is a typical basic operation which helps you instruct the hands-on user in practical bar-code reading operation. Application type: Inventory Operation: Power ON → Read the 2D code or bar code → Key in the quantity. on stock (A). Read the 2D code or bar code → Key in the quantity. on stock (B). . . . Repeat the above operation. .. . 6. Ready for data entry Record 00100 scrolls up so that record 00101 becomes ready for next data entry. 4.
Appendices Appendix D. Quality Assurance Standards D.1 Applicable Standards Standards Noise Standards Conditions* Remarks VCCI A Class B FCC Part 15 A Class A EMC Directive A Class B B Class B EN55024: 1998 IEC 61000-4-2 (1995) IEC IEC IEC IEC IEC IEC 61000-4-3 (1995) 61000-4-4 (1995) 61000-4-5 (1995) 61000-4-6 (1996) 61000-4-8 (1993) 61000-4-11 (1995) EN55022: 1995 EMC Framework AS/NZD 3548 * Conditions A: Meets this standard. (Approvement pending) B: Meets this standard.
D.2 Interface Cables With the interface cables described in this section, DENSO WAVE has run the quality assurance test conforming to the EMC Directive for the BHT-100Q/100B series and CU7001. Any connectors other than those specified here are not acceptable. They may cause the BHT or CU to fail to work according to the specifications. For BHT Cable 1 Wind the cable on a ferrite core twice and then secure the core with a heat-shrinkable tube. ➀ Connector P161 Teisin Electric Co., Ltd.
Appendices For CU Cable 2 ➀ D-sub connector D -F-T-N series (EMI-durable) Japan Aviation Electronics Industry Ltd. D-sub connector (to be connected to CU) DB-25SF-T-N [-S1] Japan Aviation Electronics Industry Ltd. ➂ Connector cover 17JE series hood/cable clamp (shielded) DDK Ltd. ➃ Connector cover 17JE-25 -1 DDK Ltd. ➄ Shielded cable RISC 5F Kitagawa Industries Co., Ltd.
Index Symbols $$BRKLST.
Index download 12, 13, 15, 16, 34, 38, 40, 42, 45, 46, 47, 48, 49, 50, 51, 68, 69, 95, 96, 97, 98, 102, 103, 104, 105, 133, 134, 135, 136, 137, 143, 171, 177, 182 driver I indicator LED 2, 4, 17, 41, 75, 76, 78, 85, 86, 144, 145, 150, 157 infrared communication iv, 15 initializing dry battery cartridge viii, 17, 19, 20, 21, 31, 129, 130, 149, 156 Dsub-25P DTE 142 interface port 10, 12, 13, 17, 40, 47, 50, 53, 54, 63, 64, 68, 81, 82, 83, 95, 98, 100, 102, 105, 107, 111, 115, 136, 138, 140, 142, 143, 1
lithium-ion battery protection sheet of the DIP switch 144, 149, 156 low battery indication 21, 129, 130 142 protocol 63, 64, 65, 66, 67, 69, 70, 118, 124, 143, 164, 165, 172, 174, 175 M Q M1 18, 71, 72 M2 18, 71, 72 M3 2, 4, 17, 71, 72 M4 2, 4, 17, 71, 72 magic key marker QR code 58, 59, 77, 149, 151, 153 R radio communication v, 40, 54, 71, 72, 149, 156 RAM 2, 3, 54, 58, 59, 61, 62, 117 xi 75, 79, 149, 156 memory size 41, 92 rechargeable battery cartridge ii, v, vi, vii, viii, 1
Index supplemental code synchronization system area 158 V 113, 155, 160 vertical parity 172 15 system down error 133 system information 41, 92 view finder 63, 66, 113, 114, 115, 2, 54, 58, 59 system message file 42, 49, 102, 103, 104, 105, 106, 107, 135, 137, 138 W wireless System Mode ii, xv, 11, 15, 16, 18, 34, 39, 40, 42, 43, 45, 47, 51, 59, 68, 69, 73, 81, 85, 115, 129, 130, 132, 134, 143, 164, 165, 174, 175, 183 system parameter file 42, 49, 95, 96, 97, 98, 99, 100, 135, 136, 137, 138 Sy
BHT-100Q/100B User's Manual First Edition, February 2001 Second Edition, October 2001 DENSO WAVE INCORPORATED The purpose of this manual is to provide accurate information in the handling and operating of the BHT-100Q/100B. Please feel free to send your comments regarding any errors or omissions you may have found, or any suggestions you may have for generally improving the manual.
