User Guide

59
S-302
85 P31 N.C. - OPEN
86 P124 _BE RST O BE Pd DVD (ESS) reset signal of unit
87 P123 BE ON I BE Pd Input of ESS IC Active state output signal
88 P122 N.C. - OPEN
89 P121 N.C. O - OPEN
90 P120 N.C. O - OPEN
91 -
92 P30 OSD_VUP O - OSD version up change selecting signal
93 -
94 P27 VUP_SEL2 O - Version upgrade UART switching selection 2
95 P26 VUP_SEL1 O - Version upgrade UART switching selection 1
96 P25 TU_STEREO I Pu Stereo indicator input of tuner
97 P24 TUNED I Pu Bureau existence detection input of tuner
98 P23 SAN_CE O -
Communication chip enable output to tuner PLL/RDS IC/FUNCTION IC(SANYO BUS)
99 P22 SAN_MOSI O - Cereal data output to tuner PLL/RDS IC/FUNCTION IC(SANYO BUS)
100 P21 SAN_CK O - Cereal clock output to tuner PLL/RDS IC/FUNCTION(SANYO BUS)
101 P20 SAN_MISO I Pu Cereal data input from tuner PLL/RDS IC(SANYO BUS)
102 P17 BE_CS INT BE Pd CS interrupt of communication with ESS
103 P16 _BE_AUDIO_RST INT BE Pu Audio reset interrupt from ESS
104 P15 SUB_REQ INT AU Pu SUB uCom (AUDIO/VIDEO) communication demand interrupt
105 P14 E2P_CS O Pu DNS Chip selection to EEPROM
106 P13 E2P_CLK O - SCI clock to EEPROM
107 P12 E2P_MOSI O - SCI DATA OUT to EEPROM
108 P11 E2P_MISO I - SCI DATA IN to EEPROM
109 P10 N.C. O - OPEN
110 P07 N.C. O - OPEN
111 P06 N.C. O - OPEN
112 P05 N.C. O - OPEN
113 P04 N.C. O - OPEN
114 P114 FL_CS Çn - FL controller chip selection
115 P113 OSD_REQ Çn - Request signal to OSD uCom
116 P112 N.C. O - OPEN
117 P111 FL_CLK SO - SCI clock output to FL controller
118 P110 FL_DOUT SO - SCI data output to FL controller
119 P03 N.C. O - OPEN
120 P02 N.C. O - OPEN
121 P01 N.C. O - OPEN
122 P00 N.C. O - OPEN
123 P157 DIMMER AD FR Pd Illuminance sensor input
124 P156 _FL_RST O Pd FLT display driver reset signal (Reset:L)
125 P155 N.C. O - OPEN
126 P154 _SUB_RST O AU Pd Reset of SUB uCom (AUDIO/VIDEO)
127 P153 SUB_ACK O AU - ACK output to SUB uCom (AUDIO/VIDEO)
128 P152 SUB_MRXD SI AU Pu SCI data input from SUB uCom (AUDIO/VIDEO
129 P151 SUB_CLK SO AU - SCI clock output to SUB uCom (AUDIO/VIDEO)
130 -
131 P150 SUB_MTXD SO AU Pu SCI data output to SUB uCom (AUDIO/VIDEO)
132 -
133 P107 PULL UP I Pu DNS PULL UP(necessity key interruption is put)
134 P106 KEY2 AD FR Pu Detection input 2 of substance operation button input
135 P105 KEY1 AD FR Pu Detection input 1 of substance operation button input
136 P104 KEY0 AD FR Pu Detection input 0 of substance operation button input
137 P103 MODE2 AD - DVD REGION selection input
138 P102 MODE1 AD - Treatment area selection input of product
139 P101 N.C. AD Pu +3.3V fixing
140 - Connect to GND
141 P100 SW1_IN AD -
HDMI/PROGRESSIVE/INTERLACE change SW input (H: HDMI, M: PROG, L: INT)
142 - Connect to +3.3V
143 - Connect to +3.3V
144 P97 N.C. O - OPEN
Pin
No
Function Port name
Port
setting
INIT PU Explanation