User Guide

ManualsBrandsDenon ManualsHome Theater SystemS-302

TOKYO, JAPAN

Denon Brand Company, D&M Holdings lnc.

●

For purposes of improvement, specifications and

design are subject to change without notice.

●

Please use this service manual with referring to the

operating instructions without fail.

●

Some illustrations using in this service manual are

slightly different from the actual set.

注意

サービスをおこなう前に、このサービスマニュアルを

必ずお読みください。本機は、火災、感電、けがなど

に対する安全性を確保するために、さまざまな配慮を

おこなっており、また法的には「電気用品安全法」に

もとづき、所定の許可を得て製造されております。

従ってサービスをおこなう際は、これらの安全性が維

持されるよう、このサービスマニュアルに記載されて

いる注意事項を必ずお守りください。

●

本機の仕様は性能改良のため、予告なく変更すること

があります。

●

補修用性能部品の保有期間は、製造打切後 8 年です。

●

修理の際は、必ず取扱説明書を参照の上、作業を行っ

てください。

●

本文中に使用しているイラストは、説明の都合上現物

と多少異なる場合があります。

X0335 V.03 DE/CDM 0801

SERVICE MANUAL

DVD HOME ENTERTAINMENT SYSTEM

MODEL JP E3 E2 EK E2A E1C E1K EUT

S-302

333

Ver. 3

HOME THEATER SYSTEM (S-302) consists of DVD SURROUND RECEIVER (ADV-S302),

SUB WOOFER (DSW-S302) and SPEAKER SYSTEM (SC-S302)

Please refer to the

MODIFICATION NOTICE.

Summary of content (155 pages)

PAGE 1
Ver. 3 Please refer to the MODIFICATION NOTICE.
PAGE 2
S-302 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
PAGE 3
㪊㪏㪇㪋㪌 3 㪈㪇㪈㪋㪏㪏㪎㩿㪮㫀㪽㫀㩷㪘㪥㪫㪜㪥㪥㪘㪀㪈㪋㪉㪅㪏㪋㪌㪊㪈㪌㪉㪋㪌㩿㪮㫀㪽㫀㩷㪘㪥㪫㪜㪥㪥㪘㪀㪉㪍㪅㪌 S-302 DIMENSION ADV-S302 㪉㪐㪋㪈㪊㪌
PAGE 4
S-302 㪋㪈㪈㪍㪏㪊㪊㪍㪅㪌 DSW-S302 㪍㪌㪅㪌㪈㪋㪈㪉㪏㪎㪈㪋㪇㪉㪈㪈㪌㪊㪅㪌㪇㪅㪌㪉㪇㪊 4
PAGE 5
S-302 76.3 SC-S302 167.
PAGE 6
S-302 WIRE ARRANGEMENT ワイヤー整形図 If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation. 調整や部品の交換等により、ワイヤー類の結束をはずしたり移動させた場合には、それらの作業が完了した時点でワイヤーの整形をおこなってください。正しく整形されてないとノイズ発生の原因となることがあります。 1. ADV-S302 1. ADV-S302 ① Fasten the CX31 3P connector cord to the circuit board with a style pin.
PAGE 7
S-302 ⑧ Fasten the CX061 6P connector cord with a cord holder.
PAGE 8
S-302 2. DSW-302 2. DSW-302 ① Fasten the CX041 4P connector cord to the chassis with a clamp band. ② Fasten the CW041 4P connector cord and CX081 8P connector cord to the chassis with a clamp band. ③ Fasten with a clamp band. ④ Fasten the CX021 2P connector cord to the chassis with a clamp band.
PAGE 9
S-302 DISASSEMBLY 各部のはずしかた (Follow the procedure below in reverse order when reassembling.) （組み立てるときは、逆の順序でおこなってください。） ● ADV-S302 1. Side panel ● ADV-S302 1. Side panel (1) Remove 4 screws 104 on the rear side and 4 screws 104 on the bottom side. (1) 背面側から 104 のねじ 4 本と底面側から 104 のねじ 4 本をはずします。 (2) Detach the Side panel. (2) Side panel をはずします。 104 104 Side panel 104 Side panel 104 2. Top cover 2. Top cover (1) Remove 3 screws 104 on the rear side and 6 screws 105 on the both sides.
PAGE 10
S-302 3. Drive unit 3. Drive unit 3.1. When the Disc tray can be ejected electrically. 3.1. ディスクトレイが電源でオープン出来る場合 (1) Switch on, and press [ the Disc tray. (1) 電源を入れ「 (OPEN/CLOSE)」ボタンを押して、ディスクトレイを開きます。 (OPEN/CLOSE)] button to open (2) Detach the Loader panel by lifting. (2) Loader Panel を持ち上げてはずします。 (3) Close the Disc tray. (3) ディスクトレイを閉じます。 (4) Remove 4 screws 102 on the top side.
PAGE 11
S-302 4. Front panel assy 4. Front panel assy (1) Remove 3 screws 106 on the bottom side. (1) 底面側から 106 のねじ 3 本をはずします。 (2) Disconnect the Wire [CX051],[CX052] and the FFC cable [CX211] from the Main unit and the Wire [CX054] from the USB unit. (2) Main unit からワイヤー [CX051]、[CX052] と FFC ケーブル [CX211] を USB キバンからワイヤー [CY054] をはずします。 (3) Remove 3 screws 103 and 2 screws 105 on the top side and 2 screws 105 on the both sides.
PAGE 12
S-302 5. Rear panel assy 5. Rear panel assy (1) Remove 10 screws 103 on the top side. (1) 天面側から 103 のねじ 10 本をはずします。 (2) Remove 5 screws 105 on the rear side and 4 screws 105 on the both sides. (2) 後面側から 105 のねじ 5 本を側面側から 105 のねじ 4 本をはずします。 (3) Detach the Rear panel assy.
PAGE 13
S-302 ● DSW-S302 1. Rear panel ● DSW-S302 1. Rear panel (1) Remove 10 screws 101 on the bottom side. (1) 底面側から 101 のねじ 10 本をはずします。 (2) Detach the Rear panel. (2) Rear panel をはずします。 101 2. SHIELD COVER 2. SHIELD COVER (1) Remove 8 screws 103 on the Side. (1) 側面側から 103 のねじ 8 本をはずします。 (2) Lift the shield cover using a flat-headed screwdriver and remove it. When doing this, be careful not to deform the main bracket's hook.
PAGE 14
S-302 ATTACHING THE ANTI-SLIP PADS すべり止めの貼りかた ※ Attach the anti-slip pads as shown on the diagram below. Press firmly so they do not peel off subsequently.
PAGE 15
S-302 DIAGNOSTICS OF OPTICAL PICKUP AND REPLACING TRAVERSE UNIT 光ピックアップの故障診断とトラバースユニットの交換 Make failure diagnostics of the Optical Pickup as follows. If the laser drive current (Iop) becomes more than 1.5 times of the initial value, the Optical Pickup should be replaced. The laser drive current initial value is checked by "Iop checked Method" of next page. In case of replacing the Pickup, change the whole part of the Traverse Unit. No mechanical adjustment is necessary after the replacement.
PAGE 16
S-302 1. Iop checked Method 1. Iop 値の確認方法 Select the laser ON/OFF (CD/DVD) mode of the test mode, and check the lop value of DVD laser or CD laser. (See page 21 for test mode.) レーザー駆動電流を確認する場合は、テストモードのレーザー ON/OFF (CD/DVD) モードを選択して、DVD レーザーまたは CD レーザーの lop 値を確認します。（詳細は 21 ページ、テストモード参照） FL 管の表示 (13 桁の表示部 ) FL Display (The display part of 13 digits) 1 2 Ｔ２ 3 4 5 6 7 8 9 10 11 12 13 1 2 L a s e r O n O f f Ｔ２ 1.1.
PAGE 17
S-302 4. Rewriting the default value of the laser current 4. レーザー電流初期値の書き換え方法レーザー電流の初期値を書き換えるには、CD または DVD レーザー電流が表示されている時にボタンを5秒以上押し、次にボタンまたはボタンを押して T23 を選択します。（詳細は 22 ページ、Iop 値の確認方法参照） To rewrite the default value of the laser current, press the button for at least 5 seconds while the CD or DVD laser current is displayed, then press the or button to select T23. (For details, see "Iop checked Method" on page 22.
PAGE 18
S-302 HOW TO REPLACE TRAVERSE UNIT Caution: The optical pickup can be damaged easily by static electricity charged on human body. Take necessary anti-static measures when repairing around the optical pickup. 1. Guide Clamp Bracket disassembly 注意 : 光ピックアップは、人体に帯電した静電気等で静電破壊することがあります。光ピックアップ周辺を修理する際は、必要な静電対策を行ってください。 3. トラバースユニットのはずしかた (1) Remove 24P FFC, 15P FFC and 5P PH WIRE connecting with from the Main P.W.B. (1) メイン基板に接続している 24P FFC、15P FFC、5P PH ワイヤをはずします。 (2) Remove 4 screws fixing Damper.
PAGE 19
S-302 SERVICE MODE サービスモードについて 1. Aging Mode 1. エージングモード 1.1. preparation0 1.1. 準備 (1) Equipment used: Any one of DVD Karaoke Disc (containing more than 10 titles). (ex : Heat run disc TDV-HR01) (1) 使用機器：DVD カラオケディスク（10 タイトル以上のもの）（例：ヒートランディスク TDV-HR01） (2) Unit setting : No spec other than the following procedure. (2) 本体設定：下記設定以外規定無。 1.2. procedure 1.2. 手順 ※ Perform aging of the DVD.
PAGE 20
S-302 2. Initial Setting Mode 2. イニシャルモード 2.1. Preparation 2.1. 準備 (1) Equipment used: None (1) 使用機器：無 (2) Unit setting: No spec other than the following procedure. (2) 本体設定：下記手順以外規定無。 2.2. Procedure 2.2. 手順 ● SYSTEM ● システム ※ This initializes the data for the function, volume, DVD mechanism, etc. ※ ファンクション、VOL 等および DVD メカのバックアップデータの初期化をおこなう。 (1) When the ON/STANDBY button is pressed to turn the set on while pressing the main unit's FUNCTION and simultaneously, the initialization mode is set.
PAGE 21
S-302 4. Test mode 4. テストモード 4.1. Entering the test mode 4.1. テストモードの設定 To enter the test mode, press the and buttons simultaneously while in the Aging mode. Not insert the disc. (The Aging mode is entered by pressing the and buttons simultaneously to turn on the AC power. When the Aging mode is set, the and indicators light.
PAGE 22
S-302 4.3. Setting the mode 4.3. モードの確定 With the mode selected, press the button to set that mode. モードを選択してある状態で ① In the laser on/off (CD/DVD) mode, laser on/off control is executed and the laser current is displayed. Press the or button to switch the CD/DVD (T21, T22, T21. .). To save the current laser current value, press and hold in the button for at least 5 seconds to turn off the "mmmm" section of the display, then press the or button and select T23.
PAGE 23
S-302 4.4. Change within the mode 4.4. モード内での変更 Changes within modes are made by pressing the and buttons while the mode is set. モードを確定してある状態で ① In the laser on/off (CD/DVD) mode, laser on/off control is executed and the laser current is displayed.
PAGE 24
S-302 4.5. Execution of trace mode (error rate display) (See "Table 2 - Trace mode details") Trace will be performed if the 4.5. トレースモード ( エラーレート表示 ) の実行（表 2 トレースモード詳細参照） button is pushed after choosing operation.
PAGE 25
S-302 Table 2: Trace mode details 表 2 トレースモード詳細 YY Contents Contents supplement 71 A display of PO error detection number of the inner circumference of 1-layer and an address. It is invalid at the time of CD operation. 71 1 層内周の PO 誤り検出数とアドレスの表示 CD 時は無効。 72 A display of PO uncorrectable number of the inner circumference of 1-layer and an address. It is invalid at the time of CD operation.
PAGE 26
S-302 TROUBLE SHOOTING トラブルシューティング ● ADV-S302 ● ADV-S302 トラブルシューティング 1. 1U-3808 (MAIN UNIT) 1.1. FL管点灯せず 1. 1U-3808 (MAIN UNIT) 1.1. FL TUBE dosen't light (1) Check the Set-up process of System μ-COM Check Power Supply Voltages. 1U-3808-1(MAIN UNIT) 䊶 [IC303]: +9V_DNS (1) システムμ-COM 立ち上がりチェック工程 N.G 電源電圧確認 1U-3808-1(MAIN UNIT) ・ [IC303]: +9V_DNS Check Soldering. 䊶 CX801 on MAIN UNIT. N.G 電源電圧確認 1U-3808-1(MAIN UNIT) ・ [IC201]: +3.3V_DNS Check Soldering. 䊶 IC303 on MAIN UNIT. N.
PAGE 27
S-302 (2) Check the Set-up process of SUB μ-COM Check Power Supply Voltages. 1U-3808-1(MAIN UNIT) ・ [IC301]: +3.3V_D1 (2) サブμ-COM 立ち上がりチェック工程 N.G 電源電圧確認 1U-3808-1(MAIN UNIT) ・ [IC301]: +3.3V_D1 Check Soldering. ・ IC305 on MAIN UNIT. N.G RESET信号の確認 1U-3808-1(MAIN UNIT) ・ [IC301]:[SUB_RST]17 pin. "H"level O.K.? Check Soldering. ・ IC301 on MAIN UNIT. N.G 発振波形確認 1U-3808-1(MAIN UNIT) ・ [IC301]: 12MHz at 18pin. Check Soldering. ・ X301 on MAIN UNIT. 半田付けを確認・ MAIN UNITのIC301 N.
PAGE 28
S-302 (3) Check the Set-up process of B/E μ-COM Check Power Supply Voltages. 1U-3808-1(MAIN UNIT) ・ [IC101]: +3.3V_D2,+2.0V_ESS O.K.? (3) B/E μ-COM N.G 立ち上がりチェック工程電源電圧確認 1U-3808-1(MAIN UNIT) ・ [IC101]: +3.3V_D2,+2.0V_ESS O.K.? Check Soldering. ・ [IC305] ・ [IC111] N.G Check 27MHz(3.3V)at 4pin of IC109. N.G O.K. クロックの波形確認 1U-3808-1(MAIN UNIT) ・ [IC101]:49,105,116pin and 117pin. 27MHz(3.3V),O.K.? (1) Check Soldering. of X101. (2) Check Soldering. of IC109 Check Soldering. Of IC112,R202 N.
PAGE 29
S-302 1.2. ディスク読めず [No Play], [00 00] 等の表示 1.2. No Sound,Noise generated [No Play], [00 00] displayed etc. (1) ディスク回転せず (1) CD,DVD PLAY Check the Emission of Pick-up. IU-3807(FEP UNIT) ・ Emission of P.U. laser O.K.? ・ The test mode "T2" is executed. Laser current O.K.? N.G (1) Check Soldering of P.U. ・ short-circuit? (2) Check the circumference soldering of TR603 and TR604. (3) Check connector insertion. ・ [P.U.
PAGE 30
S-302 1.3. 音声出力せず、ノイズ発生 1.3. No Sound,Noise generated (1) CD,DVD 再生時 (1) CD,DVD PLAY Check Power Supply Voltages. 1U-3808(MAIN UNIT) ・ +12V_A1,-12V_A1 ・ +7V,-7V of [IC601] ・ +1.2V_DSP of [IC401] N.G 電源電圧確認 1U-3808(MAIN UNIT) ・ +12V_A1,-12V_A1 ・ +7V,-7V of [IC601] ・ +1.2V_DSP of [IC401] Check Soldering. ・ CX801 ・ IC602,IC603 ・ IC404 N.G RESET信号の確認 [IC401].[IC501],[IC502] 1U-3808(MAIN UNIT) ・ [IC401]:[DSP_RST]202pin ・ [IC501]:[CODEC_RST]10 pin. ・ [IC502]:[DIR_RST]41 pin. "H"level O.K.
PAGE 31
S-302 Check Analog Audio Data output from CODEC to AMP. 1U-3808(MAIN UNIT) ・ [IC501]output and [IC506],[IC507] [FL],[FR],[SW] N.G CODECからAMPへのアナログオーディオデータ出力確認 1U-3808(MAIN UNIT) ・ [IC501]出力/[IC506],[IC507]入力: [FL],[FR],[SW] Check Soldering. ・ [IC501]:28,29,31pin ・ [IC506],[IC507] N.G オーディオミュート信号の確認 1U-3808(MAIN UNIT) ・ [DAC_MUTE] "L"level O.K.? Check Soldering. ・ [IC503]:86pin ・ TR501-505 N.G AMPからFUNC.VR.
PAGE 32
S-302 (2) アナログオーディオ入力時(AUX1,AUX2,AUX3) (2) Analog audio in(AUX1,AUX2,AUX3) Check Analog Audio Data input from AUX1-3 to FUNC.VR. 1U-3808(MAIN UNIT) ・ [AUX1-3 IN]-L/R N.G AUX1-3からFUNC.VR.へのアナログオーディオデータ入力確認 1U-3808(MAIN UNIT) ・ [AUX1-3 IN]-L/R Check Soldering. ・ JIK601 ・ [IC601]74-79pin N.G FUNC.VR.からAMPへのアナログオーディオデータ入力確認 1U-3808(MAIN UNIT) ・ [IC601]出力/[IC504],[IC505]入力 [A/D_L],[A/D_R] Check Soldering. ・ [IC601]14,17pin ・ IC504,505 N.
PAGE 33
S-302 3. 1U-3809-1 (VIDEO UNIT) 3-1.DVD 再生時 3. 1U-3809-1 (VIDEO UNIT) 3-1.DVD PLAY (1) インターレース映像出力せず (1) INTERLACE output does not outputed. Check Power Supply Voltages. 1U-3809-1(VIDEO UNIT) ・ +27V_D1,+3.3V_DV,±5V_V1,+9V_V1 N.G 電源電圧確認 1U-3809-1(VIDEO UNIT) ・ +27V_D1,+3.3V_DV,±5V_V1,+9V_V1 Check Soldering. ・ CY501 ・ IC110 N.G 電源電圧確認 1U-3809-1(VIDEO UNIT) ・ [IC201]:+2.5V_DV,+1.2V_int,+1.2V_APLL ・ [IC301]:+1.8V ・ [IC501/502]:+2.5V_DE,+2.5V_A Check Soldering.
PAGE 34
S-302 Check analog signal for Video from ENCODER to Video driver(COMPONENT) 1U-3809-1(VIDEO UNIT) ・ [IC501]output and [IC707]input: [ENC_Y],[ENC_CB],[ENC_CR] N.G ENCODERからビデオドライバーへのアナログ映像データ出力の確認(COMPONENT) 1U-3809-1(VIDEO UNIT) ・ [IC501]出力/[IC707]入力: [ENC_Y],[ENC_CB],[ENC_CR] Check Soldering. ・ [IC501]37-39pin ・ VR501-503 ・ TR501-503 ・ [IC707]10,14,16pin O.K. O.K.
PAGE 35
S-302 (2) プログレッシブ映像出力せず (2) PROGRESSIVE output does not outputed. Check Digital signal for Video from FPGA to I/P 1U-3809-1(VIDEO UNIT) ・ [IC201]output and [IC301]input: [IPID0-D7],[IPIHS],[IPIVS],[IPICK] N.G FPGAからI/Pへのデジタル映像データ出力の確認 1U-3809-1(VIDEO UNIT) ・ [IC201]出力/[IC301]入力: [IPID0-D7],[IPIHS],[IPIVS],[IPICK] Check Soldering. ・ R328-339 ・ [IC301]195-208pin N.
PAGE 36
S-302 (3) HDMI映像出力せず (3) HDMI output does not outputed. Check Power Supply Voltages. 1U-3809-1(VIDEO UNIT) ・ [IC401]:+1.8V N.G 電源電圧確認 1U-3809-1(VIDEO UNIT) ・ [IC401]:+1.8V Check Soldering. ・ IC604 N.G RESET信号の確認 1U-3809-1(VIDEO UNIT) ・ [IC401]:[HDMI_RST] "H"level O.K.? Check Soldering. ・ CY801,R812 N.G FPGAからTRANSMITTERへのデジタル映像データ出力の確認 1U-3809-1(VIDEO UNIT) ・ [IC201]出力/[IC401]入力: [HDMTY0-9],[HDMTC0-9],[HDMTHS], [HDMTVS],[HDMTDE],[HDMTCLK] Check Soldering.
PAGE 37
S-302 ● DSW-S302 1. 1U-3811 (D.AMP/SMPS UNIT) ● DSW-S302 1. 1U-3811 (D.AMP/SMPS UNIT) (1) AMPLIFER (1) アンプ Check Reset signal. (IC208 4pin) "H" level (About 3.3V) N.G. Check the following parts (and surrounding area) and their soldering. • [IC208] (BD4730) • [IC201] circumference of 9pin(TAS5066PAGRG4) Also circuits connected to this part リセット信号の確認･ (IC208 4pin） "H" レベル ( 約 3.3V) N.G. Check the following parts (and surrounding area) and their soldering.
PAGE 38
S-302 (2) WAVEFORM Waveform 1:Clock Waveform (2) 波形図 (24.576MHz) Waveform 4: A／D Waveform 波形1:クロック波形 1 (24.
PAGE 39
S-302 (3) 電源 (3) POWER SUPPLY Check FUSE Condition • FUSE (F401)OPEN? N.G. Check Primary Parts and Soldering • [D405] (GSIB660) • [IC401] (SW_TRANS) • [C432] (330/400) for E2 (1000/200) for E3/J • [T401] (SW_TRANS) ヒューズは切れているか？･ FUSE (F401) N.G. 以下部品（周辺）の状態・半田付けチェック･ [CX081] (8P-PH) ADV 側の回路のショート若しくは破損 N.G. 以下部品（周辺）の状態・半田付けチェック･ [T402] (POWER TRANS) ･ [D408 ∼ D410] (RB521S) ･ [C436] (3300/25) その他この出力の負荷となる回路 N.G.
PAGE 40
S-302 Check +12V_A Output • Voltage Check +12V_A DC (non-switched) Voltage is O.K.? (IC403 O Terminal (Output Terminal)) N.G. Check the following parts (and surrounding area) and their soldering. • [T401] (SW_TRANS) • [IC403] (KIA7812API) • [D418] RN-1Z and Other Circuits +12V_A 出力電圧は正常か？･ (IC403 O 端子 ( 出力端子 )) N.G. 以下部品（周辺）の状態・半田付けチェック･ [T401] (SW_TRANS) ･ [IC403] (KIA7812API) ･ [D418] RN-1Z その他この出力の負荷となる回路 N.G.
PAGE 41
S-302 ELECTRICAL ADJUSTMENT FOR VIDEO ビデオ回路の調整 1. SETTING 1. セッティング手順 (1) Connect the monitor TV to the video output terminal. (2) Connect the oscilloscope to the Y-signal and C-signal of S-VIDEO output terminal and each terminate at 75 Ohms. (3) Connect the oscilloscope to the Y-signal, PB-signal and PR-signal of Component video output terminal and each terminate at 75 Ohms.
PAGE 42
S-302 3. PROCEDURE 3. 手順 (1) Adjust the signal of S-VIDEO out by the wave of oscilloscope.
PAGE 43
S-302 (c) Target, PR-signal Point Check Value Waveform : : (c) PR 信号レベル調整個所調整値波形 VR503 700 ± 10mV ：VR503 ：700 ± 10ｍV PR PR PR 信号レベル PR-signal 2 2 コメント削除 Deletion of comment 43
PAGE 44
S-302 BLOCK DIAGRAMS ADV-S302 44
PAGE 45
80 4580 FR IN SW IN 45 AC IN 50/60Hz +9V_NSW 4580 FL IN SMPS 24.
PAGE 46
Sub Woofer -20dBFs -20dBFs 200mV 46 -35dBFs -30dBFs -20dBFs -10dBFs 0dBFs -10dBFs Front 0dBFs Total +37.8dB +6dB +29.0dB +20.0dB +17.8dB +17.
PAGE 47
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 VEE HA2/AUX4[4] VEE I2CDATA/AUX0 I2C_CLK/AUX1 AUX2/IOW# VSS VEE AUX3/IOR# AUX4 AUX5 AUX6 AUX7 LOE# VSS VCC LCS0#/PIXOUT_CLK LCS1# LCS2# LCS3# VSS LD0 LD1 LD2 LD3 LD4 VEE VSS LD5 LD6 LD7 LD8 LD9 LD10 LD11 VSS VEE LD12 LD13 LD14 LD15 LWRLL# LWRHL# VSS VEE CAMIN0/PIXIN0 CAMIN1/PIXIN1 LA0 LA1 LA2 LA3 VSS VEE LA4 LA5 LA6 LA7 LA8 LA9 VSS VCC LA10 LA11 LA12 LA13 LA14
PAGE 48
S-302 ES6178FF PIN DESCRIPTION Name Pin Numbers I/O 1,18, 27, 59, 68, 75, 92, 99, 104, 130, 148, 157, 159, 164, 183, 193, 201 P I/O power supply. 2-7, 10-16, 19-23, 204-207 O RISC port address bus. 8, 17, 26, 34, 43, 60, 67, 76, 84, 91, 98, 103, 120, 129, 138, 147, 156, 163, 171, 177, 184, 192, 200, 208 G Ground. 9, 35, 44, 83, 121, 139, 172 P Core power supply. 24 I Reset input; (5V tolerant input). TDMDX O TDM transmit data output. RSEL I LCS3 ROM Boot Data Width Select.
PAGE 49
S-302 Name TSD0 SEL_PLL0 TSD1 SEL_PLL1 Pin Numbers 33 36 I/O Definition O Audio transmit serial data output 0. I Refer to the description and matrix for SEL_PLL2 pin 32. O Audio transmit serial data output 1. I Refer to the description and matrix for SEL_PLL2 pin 32. TSD2 37 O Audio transmit serial data output 2. This pin must be pulled down to VSS via a 4.7-k: resistor for proper operation. TSD3 38 O Audio transmit serial data output 3. MCLK 39 I/O Audio master clock for audio DAC.
PAGE 50
S-302 Name Pin Numbers I/O DCLK 105 I Clock input to PLL; (5V tolerant input). O Video DAC output.
PAGE 51
S-302 Name Pin Numbers I/O ADVEE 111 P Analog power for video DAC. ADVSS 112 G Analog ground for video DAC. O Video DAC output. Refer to description and matrix for UDAC pin 106. O YUV pixel 5 output data PIXOUT5 O CCIR656 output pixel 5. VDAC O Video DAC output. Refer to description and matrix for UDAC pin 106. O YUV pixel 6 output data. PIXOUT6 O CCIR656 output pixel 6. FDAC O Video DAC output. Refer to description and matrix for UDAC pin 106. O YUV pixel 7 output data.
PAGE 52
S-302 Name Pin Numbers HD8 DCI_FDS# AUX2[0] 132 VFD_CLK HD9 I/O Definition I/O Host data bus line; (5V tolerant input). I/O DVD input sector start; (5V tolerant input). I/O Aux2 data I/O; (5V tolerant input). I VFD clock input. I/O Host data bus line; (5V tolerant input). I/O Aux2 data I/O; (5V tolerant input). I/O Host data bus line; (5V tolerant input). I/O Aux2 data I/O; (5V tolerant input). I/O Host data bus line; (5V tolerant input). I/O Aux2 data I/O; (5V tolerant input).
PAGE 53
S-302 Name Pin Numbers I/O Definition I/O Host write. I/O DVD channel data clock; (5V tolerant input). AUX4[5] I/O Aux4 data I/O; (5V tolerant input). HRD# O Host read. I/O DVD channel data valid; (5V tolerant input). I/O Aux4 data I/O; (5V tolerant input). HWR# DCI_CLK DCI_ACK# 149 150 AUX4[6] HIOCS16# AUX3[4] CAMCLK I 151 I/O Device 16-bit data transfer. Aux3 data I/O; (5V tolerant input). I Camera port pixel clock input. I CCIR656 input pixel clock. O Host select 1.
PAGE 54
S-302 BCOIC-DM850E-CQL (IC101: 1U-3777) 54
PAGE 55
S-302 Pin Name Pin Name Pin Name Pin Name 1 VSSIO 53 USBREF 105 A[19] 157 VSSIO 2 AV0CLK 54 VSSIOUSB 106 A[2 0] 158 VDDIO 3 VDDIO 55 VDDIOUSB 107 A[2 1] 159 A[5 ] 4 AV0DATA[0] 56 VDDUSBPLL 108 NW E 160 A[6 ] 5 AV0DATA[1] 57 VSSUSBPLL 109 NCS[2] 161 AV1DATA[0] 6 AV0DATA[2] 58 VSSIO 110 NCS[1] 162 AV1DATA[1] 7 AV0DATA[3] 59 USBXTALI 111 NCS[0] 163 AV1DATA[2] 8 GPIO[0] 60 USBXTALO 112 VSSIO 164 AV1DATA[3] 9 GPIO[6] 61 VDDIO 113 VDDIO
PAGE 56
S-302 DSP21367 (IC401: 1U-3808) 56
PAGE 57
S-302 M3087BFKBGP (IC201: 1U-3808) Pin Function No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Port name P96 P95 P94 P93 P92 P91 P90 P146 P145 P144 P143 P142 P141 P140 N.C. N.C. ON/_STBY OSD_ACK OSD_MTXD OSD_DRXD OSD_CLK N.C. N.C. N.C. N.C. _TEMP_DET AUX_SW HP_SW P87 P86 CNVSS1 RESERVE 32.768K RESERVE 32.
PAGE 58
S-302 Pin Function No 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 Port name Port INIT setting O I P85 P84 P83 P82 P81 P80 P77 P76 P75 P74 P73 P72 P71 P70 P67 NMI _REMOTE _PROTECT E_REQ P_DOWN( 50/60Hz ) IPOD_MRXD N.C.
PAGE 59
S-302 Pin Function No 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 Port name Port INIT setting P31 P124 P123 P122 P121 P120 N.C. _BE RST BE ON N.C. N.C. N.C.
PAGE 60
S-302 FRONT PANEL extension output port (BU2090F P60: F_EXT_DA /P61: F_EXT_CK) (IC202:1U-3810 ) Pin No Port 4 5 6 7 8 9 10 11 12 13 14 15 Port Name ON/ST_RD ON/ST_YL OP/CL_LED STOP_LED FUNC_LED REV_LED AFWD_LED PLAY_LED VOLT_A VOLT_B VOLT_C ON/ST_BL Port INIT setting O O O O O O O O O O O O PU Explanation - POWER button red LED lighting control: Red lighting at standby(lighting: L. ) POWER button yellow LED lighting control: Yellow lighting at timer standby(lighting: L.
PAGE 61
S-302 M30627FHPGP (IC301: 1U-3808) Pin No I/O Explanation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 VREF AVCC P97/SIN4 P96/SOUT4 P95/CLK4 P94 P93 P92/SOUT3 P91/SIN3 P90/CLK3 P141 P140 BYTE CNVCS Port name VREF AVCC DSP_MISO DSP_MOSI DSP_CK I2CSEL N.C. N.C. N.C. N.C. N.C. _FLI_RST BYTE CNVSS Function I O O O O O O O O O - 15 16 17 18 19 20 21 22 P87 P86 RESET XOUT VSS XIN VCC1 P85/NMI N.C. _HDMIT_RST SUB_RST X1 VSS X2 VCC1 _NMI O O I O I I AD standard +3.3V AD +3.
PAGE 62
S-302 Pin No Port name Function I/O Explanation I I O O O O O DIR interrupt input MAIN-SUB uCom communications control input terminal (ACK “L” return from main uCom) OPEN OPEN PWB check Reset for ADV7403 Reset for ADV7320-2 OPEN OPEN OPEN OPEN OPEN OPEN Data output for Flash rewriting /HDMI DEBUG 5 (DEBUG output for communication) +3.
PAGE 63
S-302 Pin No 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 Port name P25 P24 P23 P22 P21 P20 P17/INT5 P16/INT4 P15/INT3 P14 P13 P12 P11 P10 P07/AN07 P06/AN06 P05/AN05 P04/AN04 P03/AN03 P02/AN02 P01/AN01 P00/AN00 P117 P116 P115 P114 P113 P112 P111 P110 P107/AN7 P106/AN6 P105/AN5 P104/AN4 P103/AN3 P102/AN2 P101/AN1 AVSS P100/AN0 Function DSP_IO_MUTE _AD/DIG _ERR_MUTE _BSE TDO_VFPGA COMP_DET TMS_AV S_DET TDI_A
PAGE 64
S-302 AW9864 (IC402: 1U-3808) PIN DESCRIPTION PIN NAME A0−A10 FUNCTION Address DESCRIPTION Multiplexed pins for row and column address. Row address: A0−A10. Column address: A0−A7. A10 is sampled during a precharge command to determine if all banks are to be precharged or bank selected by BS0, BS1. BS0, BS1 Bank Select Select bank to activate during row address latch time, or bank to read/write during address latch time. DQ0−DQ31 Data Input/ Output Multiplexed pins for data output and input.
PAGE 65
S-302 NT5DS16M16CS (IC202: 1U-3809) Input/Output Functional Description Symbol Type Function Input Clock: CK and CK are differential clock inputs. All address and control input signals are sampled on the crossing of the positive edge of CK and negative edge of CK. Output (read) data is referenced to the crossings of CK and CK (both directions of crossing). CKE Input Clock Enable: CKE HIGH activates, and CKE Low deactivates, internal clock signals and device input buffers and output drivers.
PAGE 66
S-302 K4S641632 (IC103: 1U3808) ( p VDD DQ0 VDDQ DQ1 DQ2 VSSQ DQ3 DQ4 VDDQ DQ5 DQ6 VSSQ DQ7 VDD LDQM WE CAS RAS CS BA0 BA1 A10/AP A0 A1 A2 A3 V DD ) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 VSS DQ15 VSSQ DQ14 DQ13 VDDQ DQ12 DQ11 VSSQ DQ10 DQ9 VDDQ DQ8 VSS N.C/RFU UDQM CLK CKE N.C A11 A9 A8 A7 A6 A5 A4 VSS 54Pin TSOP (II) (400mil x 875mil) (0.
PAGE 67
S-302 TAS5142DKD (IC206: 1U-3811) 67
PAGE 68
S-302 TAS5121DKD (IC207: 1U-3811) GND PWM_BP GND RESET DREG_RTN GVDD M3 DREG DGND M1 M2 DVDD SD DGND OTW GND PWM_AP GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 GVDD_B GVDD_B GND BST_B PVDD_B PVDD_B OUT_B OUT_B GND GND OUT_A OUT_A PVDD_A PVDD_A BST_A GND GVDD_A GVDD_A 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 Terminal Functions TERMINAL NAME DKD FUNCTION(1) DESCRIPTION BST_A 22 P High side bootstrap supply (BST), external resistor and capacitor to OUT_A required BST_B 33 P Hi
PAGE 69
S-302 BU2360FV (IC109: 1U-3808) BD7820 (IC511: 1U-3809) BLOCK DIAGRAM FIN 1 2 3 P in No. 4 5 1 2 3 4 5 FIN P in Nam e GND (FIN) Vr e f CTL Vcc N.C. OUT A DJ Driver GND TSD CTL (1PIN) 69 Vcc (2PIN) OCP N. C.
PAGE 70
S-302 2.
PAGE 71
S-302 PRINTED WIRING BOARDS 1U-3808 MAIN P.W.B.
PAGE 72
S-302 1U-3808 MAIN P.W.B.
PAGE 73
S-302 1U-3809 VIDEO P.W.B.
PAGE 74
S-302 1U-3809 VIDEO P.W.B.
PAGE 75
S-302 1U-3810 L.PWR/DISP P.W.B.
PAGE 76
S-302 1U-3810 L.PWR/DISP P.W.B.
PAGE 77
S-302 1U-3811 D.AMP/SMPS P.W.B.
PAGE 78
S-302 1U-3811 D.AMP/SMPS P.W.B.
PAGE 79
S-302 FOIL SIDE 1U-3777 ETHERNET P.W.B.
PAGE 80
S-302 1U-3807 FEP P.W.B.
PAGE 81
S-302 NOTE FOR PARTS LIST 部品表について • • Parts for which "nsp" is indicated on this table cannot be supplied. When ordering of part, clearly indicate "1" and "I" (i) to avoid missupplying. • Ordering part without stating its part number can not be supplied. • Part indicated with the mark " ★ " is not illustrated in the exploded view. • Not including General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.
PAGE 82
S-302 PARTS LIST OF P.W.B. UNIT ＊本表に "nsp" と記載されている部品は供給できません。＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model JP : Japan model 1U-3777A ETHERNET P.W.B. UNIT ASS'Y Ref. No.
PAGE 83
S-302 Ref. No. Part No.
PAGE 84
S-302 Ref. No. Part No. Part Name OTHERS PARTS GROUP CX054 nsp 5P PH CON BASE(TAPE) +REF CX072 nsp 7P PH CON.
PAGE 85
S-302 1U-3808A/B/C MAIN P.W.B. UNIT ASS'Y Ref. No. Part No.
PAGE 86
S-302 Ref. No. TR214 Part No.
PAGE 87
S-302 Ref. No. Part No.
PAGE 88
S-302 Ref. No. C251 Part No.
PAGE 89
S-302 Ref. No. C374 Part No.
PAGE 90
S-302 Ref. No. C534 Part No.
PAGE 91
S-302 Ref. No. C710 Part No.
PAGE 92
S-302 Ref. No. C804,805 Part No.
PAGE 93
S-302 Ref. No. Part No. Part Name Remarks Q'ty New OTHERS PARTS GROUP ! CX031 nsp 3P PH CON.BASE(TAPE) +REF CX033 nsp 3P ZH-ZR CON.BASE-T CX051 nsp 5P CONN.BASE(KR-PH) CX052 nsp 5P ZH-ZR CON.BASE-T CX061 nsp 6P PH CON.BASE CX091 nsp 9P CON.BASE TUC-P CX121 nsp 12P CON.BASE TUC-P CX123,124 nsp 12P PIN HEADER(9120) CX153 nsp 15P CON.
PAGE 94
S-302 1U-3809A VIDEO P.W.B. UNIT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty New SEMICONDUCTORS GROUP IC101 00D 262 3495 003 ADV7403BSTZ-110 IC104,105 00D 263 1295 907 TA48018BF(T6L1,NQ) * IC106 00D 263 1297 905 TA48033BF(T6L1,NQ) * IC110 00D 263 1278 908 SI-8001FDE * IC201 nsp IC202 00D 262 3718 007 EP2C35F484C8N NT5DS16M16CS-6K IC203 00D 262 3715 929 M25P64-VMF6TG(EE5B) IC204 00D 262 3767 906 EPCS16SI16N/PT(GUI) * IC205 00D 262 3714 904 FCXO-05(48.
PAGE 95
S-302 Ref. No. Part No. Part Name D608-610 00D 276 0794 900 KDS160-RTK/P D713,714 00D 276 0794 900 KDS160-RTK/P D721,722 00D 276 0794 900 KDS160-RTK/P ZD801 00D 276 0683 930 UDZS5.
PAGE 96
S-302 Ref. No. Part No.
PAGE 97
S-302 Ref. No. Part No.
PAGE 98
S-302 Ref. No. Part No.
PAGE 99
S-302 Ref. No. C645 Part No.
PAGE 100
S-302 Ref. No. C840-842 Part No.
PAGE 101
S-302 Ref. No. Part No. Part Name FB301,302 nsp FBMJ1608HS280NT +1608 FB501 nsp FBMJ1608HS280NT +1608 FB614 nsp FBMJ1608HS280NT +1608 JK104 00D 204 8733 007 6P PIN JACK(FG GBR) JK401 00D 204 8719 005 19P HDMI CONNECTOR JK701 00D 204 8711 003 1P/S-TERM(SYK22) L105 00D 235 0187 901 INDUCTOR 22UH(7B12H) L201 00D 235 0125 905 INDUCTOR(FLC32C220K)+3216 L202 00D 235 0183 905 INDUCTOR 2.
PAGE 102
S-302 1U-3810A/B L.PWR/DISP P.W.B. UNIT ASS'Y Ref. No. Part No.
PAGE 103
S-302 Ref. No. Part No.
PAGE 104
S-302 Ref. No. Part No.
PAGE 105
S-302 Ref. No. Part No.
PAGE 106
S-302 Ref. No. Part No. Part Name Remarks Q'ty New OTHERS PARTS GROUP ! AS103 nsp RADIATOR AS201 nsp LED SPACER AS202-204 nsp FL SPACER AS205 nsp LED SPACER * CW051 nsp 5P PH-SAN CON.CORD CW052 nsp 5P ZH-SAN CON.CORD CX055 nsp 5P CON.BASE TUC-P CX141,142 nsp 14P SOCKET(9162S) CX154 00D 205 0770 045 15P FFC BASE(SIDE) CX303 nsp 30P CONN. SOCKET CY054 nsp 5P CONN.BASE(KR-PH) CY055 nsp 5P CON.SOCKET TUC-P CY091 nsp 9P CON.SOCKET TUC-P CY121,122 nsp 12P CON.
PAGE 107
S-302 1U-3811A/B/C D.AMP/SMPS P.W.B. UNIT ASS'Y Ref. No. Part No.
PAGE 108
S-302 Ref. No. Part No.
PAGE 109
S-302 Ref. No. Part No.
PAGE 110
S-302 Ref. No. C303-306 Part No.
PAGE 111
S-302 Ref. No. Part No.
PAGE 112
S-302 Ref. No. Part No. Part Name Remarks ! F401 00D 206 1099 045 FUSE(02153.15MXP/250V) ! F401 00D 206 1094 066 FUSE(233)T4AL125V for E3, JP ! F402 00D 206 1096 048 FUSE(218)T3.15AL250V for E2 ! F402 00D 206 1094 053 FUSE(233)T3.15AL125V for E3, JP FB201-204 nsp CHIP EMIFIL(11A121) +1608 FB205,206 nsp BEADS INDUCTOR TAPE FB207 nsp E.
PAGE 113
S-302 EXPLODED VIEW 43 102 12 102 3-6 156 3-7 40 104 3-11 3-5 103 13 4 15 U 103 103 T 50 D Q 105 M 44 11 14 154 P 103 45 40-1 41 153 E 152 10 3-8 151 162 W 42 161 3-10 103 B N V 105 46 107 108 31 31-2 31-3 103 26 32 152 103 108 24 H 30 101 27 35-1 35-3 35 157 35-2 8 34-1 R 9 K 34 105 J 36 36-1 101 104 G S S 105 25-2 47 162 6 7 G 105 103 3-13 49 49-2 105 108 106 25 N 103 24-2 18 A E 105 17 103 34-2 36-2 F M C L 34-3
PAGE 114
S-302 PARTS LIST OF EXPLODED VIEW ＊本表に "nsp" と記載されている部品は供給できません。＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊本表に "nsp" と記載されている基板 ASS’Y は供給できません。基板 ASS’Y の修理の際には基板部品表を確認のうえ、交換部品を発注してください。＊ P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts.
PAGE 115
S-302 Ref. No. Part No.
PAGE 116
S-302 Ref. No. Part No. Part Name Remarks Q'ty New SCREWS 101 0RD 471 3801 039 2X3 CBS-Z 2 102 0RD 473 7031 005 2.
PAGE 117
S-302 EXPLODED VIEW OF DVD MECHANISM UNIT WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
PAGE 118
S-302 PARTS LIST OF DVD MECHANISM UNIT ＊本表に "nsp" と記載されている部品は供給できません。＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Ref. No. Part No.
PAGE 119
S-302 POINTS OF GREASING With Cemedine 575, glue 3 joint parts of Clamper-L and H hooks. (0.05mg each x 3) *As for greasing to the R rail groove and groove's side edge, apply grease to the outer face "intentionally". (Not only running a brush into the groove, use it with pressing to the outer face consciously.) After attaching cushions, apply Cemedine 575 to the joint parts of the cushions and tabs (both sides, left and right) from the tab's back side. (0.
PAGE 120
S-302 DSW-S302 PARTS LIST OF EXPLODED VIEW 2 18 5 6 24 102 9 101 28 27 10 1-1 103 7 102 12 1-4 13 ! 105 1-2 14 17 20 19 15 16 101 11 3 101 104 4 106 107 5 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
PAGE 121
S-302 DSW-S302 PARTS LIST OF EXPLODED VIEW ＊本表に "nsp" と記載されている部品は供給できません。＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊本表に "nsp" と記載されている基板 ASS’Y は供給できません。基板 ASS’Y の修理の際には基板部品表を確認のうえ、交換部品を発注してください。＊ P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts.
PAGE 122
S-302 Ref. No. Part No.
PAGE 123
S-302 SC-S302 PARTS LIST OF EXPLODED VIEW 1 SC-S302 PARTS LIST OF EXPLODED VIEW Ref. No. Part No.
PAGE 124
S-302 PACKING VIEW 10 31 2 3 30 4 18 19 29 20 28 15 13 14 8 11 12 9 6 5 7 1 124 17
PAGE 125
S-302 PARTS LIST OF PACKING & ACCESSORIES ＊本表に "nsp" と記載されている部品は供給できません。＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe model Ref. No. Part No.
PAGE 126
S-302 WIRING DIAGRAMS ADV-S302 ADV-S302 Wiring Diagram USB connect Jack FL Display CW051 5P SAN CX062(6P PH) CX301(30P FFC) CY301(30P FFC) CY062(6P PH) 1U-3807-1 FE DRIVE UNIT 1U-3810-2 DISPLAY RIGHT UNIT CX211(21P FFC) P.IN +3.3V_D1 +3.
PAGE 127
CY023 (VH)WHT 127 CY021 (VH)WHT 3811-4 AC I/F UNIT 3811-2 I/F UNIT DSUB25P FEMALE SP TERMINAL 203 2447 008 204 3021 002 Shield 204 6821 005 CY041 (VH)WHT CY151 (PH) CY081 (PH) CX041 (VH)WHT CX151 (PH) CX021 (VH)WHT CX081 (PH) 203 6644 001 Inetrnal SP CX022 (VH)BLU DSW-S302 Wiring Diagram 3811-1 SMPS/AMP UNIT S-302 DSW-S302
PAGE 128
S-302 MEASURING METHOD AND WAVEFORMS 各部の波形と測定方法 To check the waveforms on the FEP, the GND (-) probe of the oscilloscope to “VHALF” point. (Except for lnner SW, TRVSW) FEP 基板の波形チェックを行うためにはオシロスコープの GND(-) プローブを "VHALF" ポイントに接続します。注 NOTES Measuring Disc: DVD/VT502 or TDV-520A CD/TCD-784 (It is better to use wires for extending between the probe and test points.) • When watching the HF waveform, use the extending wire as short as possible.
PAGE 129
S-302 WAVEFORMS IU-3807 FEP Unit. DVD PLAY Disc : TDV-520A CD PLAY Disc : TCD-784 RF waveform RF waveform ①ARF ①ARF ②NARF ②NARF RANGE .2 v DVD LOADING .05 ȝsec RANGE .2 v CD LOADING PLAY ③FODRV ③FODRV ④F+ ④F+ ⑤F- ⑤F- ③䇭.5 v RANGE ④䇭.5 v ⑤䇭.5 v ③䇭.5 v RANGE ④䇭.5 v ⑤䇭.5 v 0.5 sec DVD PLAY CD PLAY ⑥TRDRV ⑥TRDRV ⑦T+ ⑦T+ ⑧T- ⑧T- ⑥䇭.2 v RANGE ⑦䇭.2 v ⑧䇭.2 v ⑥䇭.2 v RANGE ⑦䇭.2 v ⑧䇭.2 v 100 ȝsec .2 ȝsec PLAY 0.
PAGE 130
S-302 NOTE FOR SCHEMATIC DIAGRAM 配線図について WARNING: Parts marked with this symbol ! have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. ! 印の部品は安全を維持するために重要な部品です。従って交換時は必ず指定の部品を使用してください。注） CAUTION: (1) 指定なき抵抗値は Ω、ｋはｋΩ、M は MΩ を示す。 Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.
PAGE 131
SCHEMATIC DIAGRAMS (1/25) 1 S-302 2 3 4 5 6 7 8 A 5 7 4 8 B 13 14 C 1 3 2 D 6 10 11 9 12 E SCHEMATIC DIAGRAMS (1/25) 1U-3807 FEP UNIT F
PAGE 132
SCHEMATIC DIAGRAMS (2/25) 1 2 S-302 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE INTERLACE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (2/25) 1U-3808-1 MAIN UNIT (1/6) B/E BLOCK F
PAGE 133
SCHEMATIC DIAGRAMS (3/25) 1 2 S-302 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (3/25) 1U-3808-1 MAIN UNIT (2/6) SYSTEM uCOM/IF BLOCK F
PAGE 134
SCHEMATIC DIAGRAMS (4/25) 1 2 S-302 3 4 5 6 7 8 A B C D E INTERLACE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (4/25) 1U-3808-1 MAIN UNIT (3/6) AUDIO VIDEO uCOM /VIDEO IO /LOCAL POWER BLOCK F
PAGE 135
SCHEMATIC DIAGRAMS (5/25) 1 2 S-302 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (5/25) 1U-3808-1 MAIN UNIT (4/6) AUDIO DSP BLOCK F
PAGE 136
SCHEMATIC DIAGRAMS (6/25) 1 2 2 S-302 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (6/25) 1U-3808-1 MAIN UNIT (5/6) CODEC/DIR BLOCK F
PAGE 137
SCHEMATIC DIAGRAMS (7/25) 1 2 S-302 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (7/25) 1U-3808-1 MAIN UNIT (6/6) FUNCTION/VOLUME BLOCK F
PAGE 138
SCHEMATIC DIAGRAMS (8/25) 1 2 S-302 3 4 5 6 7 8 A B C D E INTERLACE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (8/25) 1U-3809-1 VIDEO UNIT (1/7) VIDEO DECODER/I/O BLOCK F
PAGE 139
SCHEMATIC DIAGRAMS (9/25) 1 2 S-302 3 4 5 6 7 8 A B C D E INTERLACE VIDEO SIGNAL LINE PROGRESSIVE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (9/25) 1U-3809-1 VIDEO UNIT (2/7) GUI BLOCK F
PAGE 140
SCHEMATIC DIAGRAMS (10/25) 1 2 S-302 3 4 5 6 7 8 A B C D E INTERLACE VIDEO SIGNAL LINE PROGRESSIVE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (10/25) 1U-3809-1 VIDEO UNIT (3/7) I/P & SCALER BLOCK F
PAGE 141
SCHEMATIC DIAGRAMS (11/25) 1 2 S-302 3 4 5 6 7 8 A B C D E INTERLACE VIDEO SIGNAL LINE PROGRESSIVE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (11/25) 1U-3809-1 VIDEO UNIT (4/7) VIDEO ENCODER BLOCK F
PAGE 142
SCHEMATIC DIAGRAMS (12/25) 1 2 S-302 3 4 5 6 7 8 A B C D E INTERLACE VIDEO SIGNAL LINE PROGRESSIVE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (12/25) 1U-3809-1 VIDEO UNIT (5/7) COMPONENT VIDEO BLOCK F
PAGE 143
SCHEMATIC DIAGRAMS (13/25) 1 2 S-302 3 4 5 6 7 8 A B C D E INTERLACE VIDEO SIGNAL LINE PROGRESSIVE VIDEO SIGNAL LINE SCHEMATIC DIAGRAMS (13/25) 1U-3809-1 VIDEO UNIT (6/7) YC/CVBS BLOCK F
PAGE 144
SCHEMATIC DIAGRAMS (14/25) 1 2 S-302 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (14/25) 1U-3809-1 VIDEO UNIT (7/7) HDMI TRANSMITTER BLOCK F
PAGE 145
SCHEMATIC DIAGRAMS (15/25) 1 2 S-302 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (15/25) 1U-3777-1 DM/XM UNIT (1/2) ETHER/USB/WiFi BLOCK F
PAGE 146
SCHEMATIC DIAGRAMS (16/25) 1 2 S-302 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (16/25) 1U-3777-1 DM/XM UNIT (2/2) JPEG DECODER BLOCK F
PAGE 147
SCHEMATIC DIAGRAMS (17/25) 1 2 S-302 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (17/25) 1U-3810-5 LOCAL POWER UNIT F
PAGE 148
SCHEMATIC DIAGRAMS (18/25) 1 2 S-302 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (18/25) 1U-3810-1 DISPLAY CENTER UNIT 1U-3810-2 DISPLAY RIGHT UNIT 1U-3810-3 DISPLAY LEFT UNIT 1U-3810-12 AUX IN UNIT 1U-3810-13 H/P OUT UNIT F
PAGE 149
SCHEMATIC DIAGRAMS (19/25) 1 2 S-302 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (19/25) 1U-3810-4 USB TERMINAL UNIT 1U-3810-6 RS-232C UNIT 1U-3810-7 SWITCH UNIT 1U-3810-8 TUNER/R to R/IPOD UNIT 1U-3810-9 IF-1 UNIT 1U-3810-10 IF-2 UNIT 1U-3810-11 IF-3 UNIT F
PAGE 150
SCHEMATIC DIAGRAMS (20/25) 1 2 S-302 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (20/25) 1U-3811-2 I/F UNIT 1U-3811-4 AC I/F UNIT F
PAGE 151
SCHEMATIC DIAGRAMS (21/25) 1 2 S-302 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (21/25) 1U-3811-1 D.
PAGE 152
SCHEMATIC DIAGRAMS (22/25) 1 2 S-302 3 4 5 6 7 8 A B C D E AUDIO SIGNAL LINE SCHEMATIC DIAGRAMS (22/25) 1U-3811-1 D.
PAGE 153
SCHEMATIC DIAGRAMS (23/25) 1 2 S-302 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (23/25) 1U-3811-1 D.
PAGE 154
SCHEMATIC DIAGRAMS (24/25) 1 2 S-302 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (24/25) 1U-3811-1 D.
PAGE 155
SCHEMATIC DIAGRAMS (25/25) 1 2 S-302 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (25/25) 1U-3811-1 D.