User Guide

ManualsBrandsDenon ManualsStereo SystemS-301

SERVICE MANUAL

DVD HOME THEATER SYSTEM

MODEL S-301

TOKYO, JAPAN

Denon Brand Company, D&M Holdings Inc.

Some illustrations using in this service manual are

slightly different from the actual set.

●

Please use this service manual with referring to the

operating instructions without fail.

●

For purposes of improvement, specifications and

design are subject to change without notice.

●

本文中に使用しているイラストは、説明の都合上現物

と多少異なる場合があります。

●

修理の際は、必ず取扱説明書を参照の上、作業を行っ

てください。

サービスをおこなう前に、このサービスマニュアルを

必ずお読みください。本機は、火災、感電、けがなど

に対する安全性を確保するために、さまざまな配慮を

おこなっており、また法的には「電気用品安全法」に

もとづき、所定の許可を得て製造されております。

従ってサービスをおこなう際は、これらの安全性が維

持されるよう、このサービスマニュアルに記載されて

いる注意事項を必ずお守りください。

●

本機の仕様は性能改良のため、予告なく変更すること

があります。

●

補修用性能部品の保有期間は、製造打切後8年です。

注意

X0245 V.01 DE/CDM 0508

For U.S.A., Canada,

Europe & Japan model

HOME THEATER SYSTEM (S-301) consists of DVD SURROUND RECEIVER (ADV-S301)

and SUB WOOFER (DSW-S301) and SPEAKER SYSTEM (SC-S301)

Ver. 1

Summary of content (213 pages)

PAGE 1
For U.S.A., Canada, Europe & Japan model SERVICE MANUAL MODEL Ver.
PAGE 2
S-301 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
PAGE 3
S-301 DISASSEMBLY 各部のはずしかた (Follow the procedure below in reverse order when reassembling.) （組み立てるときは、逆の順序でおこなってください。） 1. Loader Panel (1) Switch on, and press [ to open the Disc tray. 1. ローダーパネルのはずしかた (OPEN/CLOSE)] button (1) 電源を入れ「 (OPEN/CLOSE)」ボタンを押して、ディスクトレイを開きます。 (2) Detach the Loader Panel by lifting. (2) ローダーパネルを持ち上げてはずします。 2. サイドパネル、ボトムカバーのはずしかた 2. Side Panel, Bottom Cover (1) Remove 13 bottom screws.
PAGE 4
S-301 3. Top Cover 3. トップカバーのはずしかた (1) Remove 9 top screws, then detach Top Cover. (1) トップカバーを止めている上部のネジ 9 本をはずし、トップカバーを矢印の方向へはずします。 4. フロントパネルのはずしかた 4. Front Panel Ass’y (1) Remove 3 Front panel screws, then detach P.W.B. and chassis. (1) フロントパネルからの基板とシャーシを止めているネジを 3 本はずします。 (2) Remove 4 Front panel side screws, then detach the Front Panel Ass’y. (2) フロントパネル側面を止めているネジ 4 本（左右各 2 本）をはずし、フロントパネルを矢印の方向へはずします。 5. Front Panel Ass’y 5.
PAGE 5
S-301 6. DVD Mecha 6. DVD メカの取りはずしかた (1) Remove 4 screws, then detach P.W.B.(1U-3695-1, 1U-3695-2, 1U-3695-3) and TUNER PACK. (1) ネジを 4 本はずし、1U-3695-1 基板と 1U-3695-2 基板と 1U-3695-3 基板と TUNER PACK をはずします。 1U-3695-3 TUNER PACK 1U-3695-1 1U-3695-2 (2) Remove 6 screws, then detach 1uU-3692 P.W.B. with DVD mecha from bottom chassis.
PAGE 6
S-301 7. Traverse Unit Disassembly 7. トラバースユニットのはずしかた Caution: The optical pickup can be damaged easily by static electricity charged on human body. Take necessary anti-static measures when repairing around the optical pickup. 注意：光ピックアップは、人体に帯電した静電気等で静電破壊することがあります。光ピックアップ周辺を修理する際は、必要な静電対策を行ってください。 7.1. Guide Clamp Bracket disassembly 7.1. ガイドクランプブラケットのはずしかた (1) Remove 2 screws. (1) ねじ 2 本をはずします。 (2) Remove Guide Clamp Bracket to arrow direction. (2) ガイドクランプブラケットを矢印の方向にとりはずします。 7.2.
PAGE 7
S-301 7.3. Traverse Unit disassembly 7.3. トラバースユニットのはずしかた (1) Remove 24P FFC (CX241), 15P FFC (CX151), 5P PH WIRE (CX051) connecting with from 1U-3692 P.W.B. (1) 1U-3692 基板に接続している 24P FFC（CX241)、 15P FFC（CX151)、5P PH ワイヤ（CX051) をはずします。 (2) Remove 4 screws fixing Damper. (2) ダンパーを固定しているねじ 4 本をはずします。 (3) Remove Traverse Unit to arrow direction. (3) トラバースユニットを矢印の方向にとりはずします。 1U-3692 P.W.B. Note for disassembly Traverse Unit トラバースユニット分解の注意 (1) When assembling, reverse the order of the above.
PAGE 8
S-301 DIAGNOSTICS OF OPTICAL PICKUP AND REPLACING TRAVERSE UNIT 光ピックアップの故障診断とトラバースユニットの交換 Make failure diagnostics of the Optical Pickup as follows. If the laser drive current (Iop) becomes more than 1.5 times of the initial value, the Optical Pickup should be replaced. The laser drive current is registered on the seal attached to the rear of the Mecha.Unit. In case of replacing the Pickup, change the whole part of the Traverse Unit. No mechanical adjustment is necessary after the replacement.
PAGE 9
S-301 1. Label Indication of SACD Mechanism. 1. SACD メカのラベル表示 Laser current consumption value ex) DVD 㧖㧖㧖 mA, CD 㧖㧖㧖 mA ࡟࡯ࠩ࡯㚟േ㔚ᵹ୯ ଀㧕DVD 㧖㧖㧖 mA, CD 㧖㧖㧖 mA 2. Note for Handling the Laser Pick-Up 2. レーザーピックアップの取扱注意 The protection for the damage of laser diode. If you want to change the optical device unit from any other units, you must keep the following. (1) It should be done at the desk already took measures the static electricity in care of removing the OPU's (Optical device unit) connector cable.
PAGE 10
S-301 4.1. DVD Laser current measurement 4.1. DVD レーザー電流測定 LD (DVD) LD (DVD) +5V-A2 +5V-A2 Oscilloscope Oscilloscope (1) Connect the oscilloscope to +5V-A2 of test point for GND side and LD (DVD) of test point for signal side. (2) Playback the multi layer track 1 of the DVD Test Disc. (3) Measure the voltage between +5V-A2 and LD (DVD), calculate Iop by the formula as shown below.
PAGE 11
S-301 Special operating procedures 特殊操作方法 1. Initialization 1. 初期化 ※ This initializes the data for the function, volume, ※ ファンクション、VOL 及び DVD メカ (RL-874) 等の DVD mechanism (RL-874), etc. (1) Check that the AC cord is disconnected from the power outlet. (AC OFF) (1) AC コードがコンセントより外れていることを確認します。(AC OFF) (2) While pressing the FUNCTION and OPEN/CLOSE ( ) buttons on the main unit, plug the AC cord into the power outlet.
PAGE 12
S-301 ADJUSTMENT 調整 1. SETTING 1. セッティング手順 (1) Connect the oscilloscope to the Y-signal, PB-signal and CB-signal, PR-signal and CR-signal of ZONE2 COMPONENT OUT terminal and each terminate at 75 Ohms. ※ Use the 75 Ohms resistance must be 1% (1) セットの ZONE2 COMPONENT OUT の端子（Y, PB/CB, PR/CR ）をそれぞれオシロスコープ（終端抵抗：75Ω）に接続します。 (2) DVD test disc : DVDT-S01 (2) DVD テストディスク：DVDT-S01 を用意します。 (3) S OUT of DVD player is connected to AUX1 S IN. (3) DVD プレーヤーの S OUT を AUX1 S IN に接続します。 ※ 2.
PAGE 13
S-301 2.4. Procedure 2.4. 手順 (1) Adjust the signal of COMPONENT OUT by the wave of oscilloscope.
PAGE 14
S-301 BLOCK DIAGRAM 㪛㪪㪮㪄㪪㪊㪇㪈㪘㪛㪭㪄㪪㪊㪇㪈㪟㪞㪘㪠㪥㪛㫀㪽㪽㪅㩷㪠㫅㫇㫌㫋㪛㪪㪛㩷㪦㪬㪫㪜㪯㪫㪪㪮㪤㪬㪫㪜㪈㪆㪉㩿㪛㪘㪚㪀㪛㪪㪛㪆㪧㪚㪤㪛㪘㪚㪛㪪㪛㩷㪠㪥㪛㪪㪛㪈㪎㪐㪈㪄㪛㪘㪚㪶㪤㪬㪫㪜㪜㪣㪜㪚㪅㪭㪩㩷㩷㪙㪛㪊㪏㪈㪈㩿㪈㪆㪉㪀㪤㪬㪫㪜㪚㪦㪘㪠㪥㪩㪯㪈㪛㪠㪩㪩㪜㪚㩷㩷㪣㪆㪩㪤㪬㪫㪜㪩㪯㪇㪄㪍䉕㪪㪜㪣㪜㪚㪫䈚䈩಴ജ 㪂㪊㪈㪭㪪㪤㪧㪪㩷㪬㪥㪠㪫㪂㪌㪅㪇㪭㪶㪥㪪㪮㪣㪦㪞㪠㪚㪘㪛㪈㪏㪊㪎㪏㪺㪿㪚㪦㪛㪜㪚㪉㪆㪉㩿㪘㪛㪚㪀㪛㪠㪩㪆㪚㪦㪛㪜㪚㪶㪚㪣㪢㪛㪠㪩㪶㪚㪜㪛㪠㪩㪆㪚㪦㪛㪜㪚㪶㪛㪠㪥㪛㪠㪩㪶㪛㪦㪬㪫㪛㪠㪩㪶㪩㪪㪫㪆㪠㪥㪫㪈㪙㪪㪜㪜㪩㪩㪤㪬㪫㪜㪪㪜㪣㪚㪣㪢㩿㪛㪠㪩㪆㪚㪦㪛㪜㪚㪶㪚㪣㪢㪀㩿㪛㪠㪩㪆㪚㪦㪛㪜㪚㪶㪛㪠㪥㪀㪚㪣㪘㪫㪚㪟㪚㪦㪛㪜㪚㪶㪩㪪㪫㪉㪊㪉㪚㪩㪜㪤㪦㪫㪜㩷㪠㪆㪦㪣㪤㪪㪉㪇㪉㪚㪯㪘㪈㪌㪈㪈㪎㪋㪣㪭㪇㪏㪎㪋㪣㪭㪇㪏㪩㪜㪤㪦㪚㪦㪥㪩㪜㪚㪠㪜㪭㪜㪩㪞㪧㪈㪬㪜㪉㪎㪈㪯㪝㫉㫆㫅㫋㩷㪪㪧㪚㫆㫅㫅㪼㪺㫋㩷㪛㪼㫋㪼㪺㫋㪣㪦
PAGE 15
㪄㪋㪇㪻㪙㪝㫊㪄㪊㪇㪻㪙㪝㫊㪄㪉㪇㪻㪙㪝㫊㪄㪈㪇㪻㪙㪝㫊㪇㪻㪙㪝㫊㪪㪮㪄㪺㪿㪄㪉㪇㪻㪙㪝㫊㪄㪈㪇㪻㪙㪝㫊㪇㪻㪙㪝㫊㪝㫉㫆㫅㫋㪄㪺㪿㪂㪍㪻㪙㪂㪍㪻㪙㪂㪉㪅㪏㪌㪻㪙㪂㪊㪅㪊㪈㪻㪙㪫㫆㫋㪸㫃㩷㪂㪊㪍㪅㪌㪉㪻㪙㪂㪉㪐㪅㪊㪌㪻㪙㪂㪉㪇㪅㪏㪊㪻㪙㪄㪉㪅㪊㪻㪙㪄㪉㪅㪊㪻㪙㪄㪈㪉㪅㪍㪻㪙㪄㪍㪅㪐㪻㪙㪂㪉㪋㪅㪐㪻㪙㪂㪉㪋㪅㪐㪻㪙 S-301 LEVEL DIAGRAM
PAGE 16
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 VEE HA2/AUX4[4] VEE I2CDATA/AUX[0] I2C_CLK/AUX[1] AUX[2]/IOW# VSS VEE AUX[3]/IOR# AUX[4] AUX[5] AUX[6] AUX[7] LOE# VSS VCC LCS0# LCS1# LCS2# LCS3# VSS LD0 LD1 LD2 LD3 LD4 VEE VSS LD5 LD6 LD7 LD8 LD9 LD10 LD11 VSS VEE LD12 LD13 LD14 LD15 LWRLL# LWRHL# VSS VEE CAMIN0 CAMIN1 LA0 LA1 LA2 LA3 VSS VEE LA4 LA5 LA6 LA7 LA8 LA9 VSS VCC LA10 LA11 LA12 LA13 LA14 LA15 LA16
PAGE 17
S-301 ES6138F Pin Description Name Pin Numbers I/O 1,18, 27, 59, 68, 75, 92, 99, 104, 130, 148, 157, 159, 164, 183, 193, 201 P I/O power supply. 2:7, 10:16, 19:23, 204:207 O RISC port address bus. 8, 17, 26, 34, 43, 60, 67, 76, 84, 91, 98, 103, 120, 129, 138, 147, 156, 163, 171, 177, 184, 192, 200, 208 G Ground. 9, 35, 44, 83, 121, 139, 172 P Core power supply. 24 I Reset input (active-low). TDMDX O TDM transmit data output. RSEL I LCS3 ROM Boot Data Width Select.
PAGE 18
S-301 p Name ( Pin Numbers TSD0 ) I/O Definition O Audio transmit serial data port 0. I Refer to the description and matrix for SEL_PLL2 pin 32. O Audio transmit serial data port 1. I Refer to the description and matrix for SEL_PLL2 pin 32. 33 SEL_PLL0 TSD1 36 SEL_PLL1 TSD2 37 O Audio transmit serial data output 2. TSD3 38 O Audio transmit serial data output 3. NC 48 — No connect pins. Leave open. MCLK 39 I/O Audio master clock for audio DAC.
PAGE 19
S-301 p ( ) Name Pin Numbers I/O Definition DSCK 102 O Output clock to DRAM. DCLK 105 I Clock input to PLL. YUV0 O YUV pixel 2 output data. CAMIN2 I Camera YUV 2. UDAC O Video DAC output.
PAGE 20
S-301 p Name ( ) Pin Numbers I/O Definition 112 G Analog ground for video DAC. O YUV pixel 5 output data. O Video DAC output. Refer to description and matrix for UDAC pin 106. O YUV pixel 6 output data. VDAC O Video DAC output. Refer to description and matrix for UDAC pin 106. YUV7 O YUV pixel 7 output data. O Video DAC output. Refer to description and matrix for UDAC pin 106. I Camera YUV 3.
PAGE 21
S-301 p Name ( Pin Numbers ) I/O Definition I/O Host data bus line 9. I/O Aux2 data I/O. I/O Host data bus line 10. AUX2[2] I/O Aux2 data I/O. HD11 I/O Host data bus line 11. I/O Aux2 data I/O. IRQ O IRQ. HD12 I/O Host data bus line 12. I/O Aux2 data I/O. HD9 133 AUX2[1] HD10 134 AUX2[3] AUX2[4] 135 136 C2PO I HD13 I/O Host data bus line 13. I/O Aux2 data I/O. AUX2[5] 137 SP I HD14 C2PO error correction flag from CD-ROM. 16550 UART serial port input.
PAGE 22
S-301 p Name ( Pin Numbers HRD# DCI_ACK# 150 AUX4[6] HIOCS16# CAMCLK 151 AUX3[4] ) I/O Definition O Host read (active-low). O DVD channel data valid (active-low). I/O Aux4 data I/O. I Device 16-bit data transfer (active-low). I Camera port pixel clock input. I/O Aux3 data I/O. O Host select 1 (active-low). I/O Aux3 data I/O. O Host select 3 (active-low). I/O Aux3 data I/O. I/O Host address bus. I/O Aux4 data I/Os. I/O Auxiliary port 0 (open collector). I/O I2C data I/O.
PAGE 23
S-301 FLI2310 (IC403: 1U-3692) HSYNC1_PORT1 VSYNC1_PORT1 FIELD ID1_PORT1 IN_CLK1_PORT1 HSYNC2_PORT1 PLL_PVDD PLL_PVSS AVDD_PLL_BE2 AVDD_PLL_BE1 AVSS_PLL_BE1 160 165 AVDD_PLL_SDI AVSS_PLL_SDI AVSS_PLL_BE2 R_VSS AVSS_PLL_FE AVDD_PLL_FE R_VSS R_VDD1.
PAGE 24
S-301 Pin details Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Pin Name HSYNC1_PORT1 VSYNC1_PORT1 FIELD ID1_PORT1 IN_CLK1_PORT1 HSYNC2_PORT1 VSYNC2_PORT1 FIELD ID2_PORT1 VDD1 VSS IN_CLK2_PORT1 B/Cb/D1_0 B/Cb/D1_1 B/Cb/D1_2 B/Cb/D1_3 B/Cb/D1_4 VDDcore1 VSScore B/Cb/D1_5 B/Cb/D1_6 B/Cb/D1_7 R/Cr/Cb Cr_0 R/Cr/Cb Cr_1 R/Cr/Cb Cr_2 R/Cr/Cb Cr_3 R/Cr/Cb Cr_4 R/Cr/Cb Cr_5 R/Cr/Cb Cr_6 R/Cr/Cb Cr_7 G/Y/Y_0 VDD2 VSS G/Y/Y_1 G/Y/Y_
PAGE 25
S-301 Pin No 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 Pin Name SCLK SDATA RESET_N VDD3 VSScore SDRAM DATA(0) SDRAM DATA(1) SDRAM DATA(2) SDRAM DATA(3) SDRAM DATA(4) SDRAM DATA(5) SDRAM DATA(6) SDRAM DATA(7) SDRAM DATA(8) SDRAM DATA(9) SDRAM DATA(10) SDRAM DATA(11) VDD4 VSS SDRAM DATA(12) SDRAM DATA(13) SDRAM DATA(14) SDRAM DATA(15) VDDcore3 VSScore SDRAM DATA(16) SDRAM DATA(17) SDRAM DATA(18) SDRAM DATA(19) SDRAM DA
PAGE 26
S-301 Pin No 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 Pin Name VSS TEST IN SDRAM ADDR(10) SDRAM ADDR(9) SDRAM ADDR(8) SDRAM ADDR(7) SDRAM ADDR(6) VDDcore5 VSScore SDRAM ADDR(5) SDRAM ADDR(4) SDRAM ADDR(3) SDRAM ADDR(2) SDRAM ADDR(1) SDRAM ADDR(0) SDRAM WEN SDRAM RASN SDRAM CASN SDRAM BA1 SDRAM BA0 SDRAM CSN SDRAM DQM SDRAM CLKOUT VDD6 VSS SDRAM CLKIN TEST3 TEST OUT0 TEST OUT1 / Interrupt 117 Out 118 CTLOUT0 119 CTLOUT1 120 CTLOUT2 121 CTLOUT3 122
PAGE 27
S-301 Pin No 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 Pin Name VDD7 VSS B/U/Pb_OUT_2 B/U/Pb_OUT_3 B/U/Pb_OUT_4 B/U/Pb_OUT_5 B/U/Pb_OUT_6 B/U/Pb_OUT_7 R/V/Pr_OUT_0 R/V/Pr_OUT_1 VDDcore7 VSScore R/V/Pr_OUT_2 R/V/Pr_OUT_3 R/V/Pr_OUT_4 R/V/Pr_OUT_5 R/V/Pr_OUT_6 R/V/Pr_OUT_7 VDD8 VSS G/Y/Y_OUT_0 G/Y/Y_OUT_1 G/Y/Y_OUT_2 G/Y/Y_OUT_3 G/Y/Y_OUT_4 G/Y/Y_OUT_5 G/Y/Y_OUT_6 G/Y/Y_OUT_7
PAGE 28
S-301 Pin No 172 173 174 175 176 177 178 179 180 Pin Name DAC_AVSSB DAC_GOUT DAC_AVDDG DAC_AVSSG DAC_ROUT DAC_AVDDR DAC_AVSSR DAC_COMP DAC_RSET 181 DAC_VREFOUT 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 Note: DAC_VREFIN DAC_AVDD DAC_AVSS DAC_GR_AVSS DAC_GR_AVDD DAC_PVDD TEST0 TEST1 TEST2 XTAL IN XTAL OUT VDD9 VSS IN_CLK_PORT 2 D1_IN_0 VDDcore8 VSScore D1_IN_1 D1_IN_2 D1_IN_3 D1_IN_4 D1_IN_5 D1_IN_6 D1_IN_7 FIELD ID_PORT 2 VSYNC_ PORT 2 HSY
PAGE 29
S-301 CXD1885Q (IC805: 1U-3692) AVDD33 DA0 (TSCON) DA1 (SLED) DA2 (FSCON) DA3 (SLED2_TILT) AVSS FG SPWM1 SPWM2 D/A GPWM0 GPWM1 GPWM2 GPWM3 GPWM4 GPWM5 XLCAS XUCAS XMOE RA11 RA10 DVSS RA9 RA8 RA7 RA6 RA5 DVDD33 RA4 RA3 RA2 DVDD18 RA0 RA1 XRAS XMWR PWM.
PAGE 30
S-301 16/4M DRAM BCA HFD Data Slicer HF ECC Core Memory manager DVD Demodulation EDC MPEG I/F ASP VSTEM Serial I/F ASP Serial I/F PWM ATC Mecha control Servo singnal GIO Direction ROM/RAM A/D ICU Terminal Name Audio CMD/ RSP reg. DSP Data RAM VSTEM DSP CLK/Mode Audio I/F MCU I/F MCU ICU Servo control X'tal D/A PWM Timer Functions Peri.
PAGE 31
S-301 No. Terminal Name I/O A/D 31 SYSCK O D Clock Classification Clock Monitor output. Function VDD & GND Digital 1.8V Power. (Internal logic system power) 32 DVDD18 P 33 XI I D Clock Crystal oscillation input. 34 XO O D Clock Crystal oscillation output. 35 DVSS P VDD & GND Digital Ground. 36 VDT7 O D VSTEM A/V MPEG data output 7. 37 VTD6 O D VSTEM A/V MPEG data output 6. 38 DVSS P 39 VDT5 O 40 VDT4 41 VDT3 42 VDD & GND Digital Ground.
PAGE 32
S-301 No. 92 Terminal Name AD1 I/O A/D I A ADC Classification Function A ADC AD2 Input. VDD & GND Analog 3.3V Power. 93 AD2 I 94 AVDD33 P 95 AD3 I A ADC AD3 Input. 96 AD4 I A ADC AD4 Input. 97 AD5 I A ADC AD5 Input. 98 AD6 I A ADC AD6 Input. 99 AD7 I A ADC AD7 Input. 100 AD8 I A ADC AD8 Input. 101 AD9 I A ADC AD9 Input. 102 VREFH I/O A ADC Max Reference Voltage input for ADC.
PAGE 33
S-301 No. Terminal Name I/O A/D 150 RD14 I/O D DRAM I/F DRAM data input/output terminal 14. * 151 RD13 I/O D DRAM I/F DRAM data input/output terminal 13. * 152 RD12 I/O D DRAM I/F DRAM data input/output terminal 12. * 153 RD11 I/O D DRAM I/F DRAM data input/output terminal 11. * 154 RD10 I/O D DRAM I/F DRAM data input/output terminal 10. * 155 RD9 I/O D * 156 DVDD18 157 DVDD33 158 RD8 I/O D DRAM I/F DRAM data input/output terminal 8.
PAGE 34
S-301 BCOIC-DM850-CQL (IC101: 1U-3693) 34
PAGE 35
S-301 Pin Name Pin Name Pin Name Pin Name 1 VSSIO 53 USBREF 105 A[19] 157 VSSIO 2 AV0CLK 54 VSSIOUSB 106 A[20] 158 VDDIO 3 VDDIO 55 VDDIOUSB 107 A[21] 159 A[5] 4 AV0DATA[0] 56 VDDUSBPLL 108 NWE 160 A[6] 5 AV0DATA[1] 57 VSSUSBPLL 109 NCS[2] 161 AV1DATA[0] 6 AV0DATA[2] 58 VSSIO 110 NCS[1] 162 AV1DATA[1] 7 AV0DATA[3] 59 USBXTALI 111 NCS[0] 163 AV1DATA[2] 8 GPIO[0] 60 USBXTALO 112 VSSIO 164 AV1DATA[3] 9 GPIO[6] 61 VDDIO 113 VDDIO 165
PAGE 36
S-301 CXD2753R (IC602: 1U-3692) Pin Assignment Block Diagram 36
PAGE 37
S-301 Terminal Functions Pin Name 1 I/O Functions VSC - It fixed to ground.( for Core) 2 XMSLAT I Latch input for µCOM serial communication. I Shift clock input for µCOM serial communication. I Data input for µCOM serial communication. 5 VDC - +2.5V Power for Core. 6 MSDATO O Data output for µCOM serial communication. “Hi-Z” potential except the output mode. 7 MSREADY O Completion flag of output preparation for µCOM serial communication. “L” is outputted at the time of completion.
PAGE 38
S-301 Pin Name I/O Functions 50 TESTO O Output for TEST. (open) 51 TESTI I Input for TEST. It fixed to “L” potential. 52 TESTI I Input for TEST. It fixed to “L” potential. 53 TESTO O Output for TEST. (open) 54 VDC - +2.5V Power for CORE. 55 DSADML O DSD Data output terminal for Lch Down Mix. 56 DSADMR O DSD Data output terminal for Rch Down Mix. 57 BCKASL I I/O selection terminal of the Bit clock for DSD data output.
PAGE 39
S-301 Pin Name I/O Functions 96 TESTI I TEST input terminal. It fixed to “L” potential. 97 TESTI Ipu TEST input terminal. It fixed to “H” potential. 98 TESTO O TEST output terminal. (open) VDC - +2.5V Power for CORE. 100 99 TESTI I TEST input terminal. It fixed to “L” potential. 101 TESTI I TEST input terminal. It fixed to “L” potential. 102 TESTI I TEST input terminal. It fixed to “L” potential. 103 TESTI I TEST input terminal. It fixed to “L” potential.
PAGE 40
S-301 Pin Name I/O Functions 148 A11 O Address output terminal for SDRAM. (MSB) 149 A10 O Address output terminal for SDRAM. 150 VSC - Ground for CORE. 151 A9 O Address output terminal for SDRAM. 152 A8 O Address output terminal for SDRAM. 153 VDC - +2.5V Power for CORE. 154 A7 O Address output terminal for SDRAM. 155 A6 O Address output terminal for SDRAM. 156 A5 O Address output terminal for SDRAM. 157 A4 O Address output terminal for SDRAM.
PAGE 41
S-301 ADSP-21266SKSTZ-1C (IC906: 1U-3694) 109 144 108 1 PIN 1 INDICATOR TOP VIEW 73 36 72 37 ADSP-21266SKSTZ-1C Terminal Function Pin Name LQFP Pin # Pin Name LQFP Pin # Pin Name LQFP Pin # Pin Name LQFP Pin # VDDINT CLKCFG0 CLKCFG1 BOOTCFG0 BOOTCFG1 GND VDDEXT GND VDDINT GND VDDINT GND VDDINT GND FLAG0 FLAG1 AD7 GND VDDINT GND VDDEXT GND VDDINT AD6 AD5 AD4 VDDINT GND AD3 AD2 VDDEXT GND AD1 AD0 WR VDDINT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
PAGE 42
S-301 M30627FHPGP (IC202: 1U-3694) PIN NO Port Function Port setting Port Name Explanation 1 VREF I VREF Reference Voltage Input for A/D converter 2 AVcc I AVcc Positive power 3 SIN4 O FL_CS Chip Enable output to FLD 4 SOUT4 SO FL_DA Serial Data output to FLD 5 CLK4 SO FL_CK Serial Clock output to FLD 6 P94 I BUSY1 Interrupt request from DSP 7 P93 ACK1 Interrupt request from DSP 8 SOUT3 SO DSPMOSI Serial Data output to DSP I 9 SIN3 SI DSPMISO Serial Data in
PAGE 43
S-301 PIN NO Port Function Port setting Port Name Explanation 27 P80 O LD_CONT LD power control signal output. H:DVD L:CD 28 P77 I USB_REQ Interrupt Request from USB Module. 29 P76 O V_CONT DVD LOADER control signal output. (PWM) 30 P75 I VOL JOG-B VOL encoder Pulse-B input 31 P74 I VOL JOG-A VOL encoder Pulse-A input 32 P73 O USB_CE Chip Enable output to USB Module. 33 P72 USB_MODE Status signal input from USB Module.
PAGE 44
S-301 PIN NO Port Function Port setting Port Name Explanation 82 P122 O 83 P121 O DIR RST Reset output to DIR Not Used: N. C. 84 P120 O CLATCH Latch Output to AD1837. 85 VCC2 86 P30 O CODEC_RST Reset output to AD1837 87 VSS 88 P27 O TU_POWER 89 P26 I STEREO "STEREO" indicator input from FM/AM TUNER pack 90 P25 I TUNED "TUNED" detect input from FM/AM TUNER pack 91 P24 O TMUTE MUTE output to TUNER. L:MUTE Positive power GND TUNER Power ON/OFF output.
PAGE 45
S-301 HY57V6432320DTP (IC404: 1U-3692) PIN CONFIGURATION BLOCK DIAGRAM I/O Control Data Input Register 512K x 32 Output Buffer 512K x 32 512K x 32 Sense AMP ADD Row Decoder CLK 512K x 32 Col. Buffer LCBR Column Decoder Latency & Burst Length LCKE Programming Register LRAS LCBR LWE LCAS LWCBR LDQM Timing Register CLK CKE CS RAS CAS WE DQM PIN FUNCTION DESCRIPTION Pin LWE LDQM Bank Select LRAS VSS DQ15 VSSQ DQ14 DQ13 VDDQ DQ12 DQ11 VSSQ DQ10 DQ9 VDDQ DQ8 N.C VSS DQM1 N.C N.
PAGE 46
S-301 IN22 IN21 IN12 IN11 ROUT32 ROUT31 ROUT22 ROUT21 ROUT12 ROUT11 AGND10 GOUT2 VIN2 AGND9 GOUT1 VIN1 BD3811K1 (IC504: 1U-3694) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 IN31 1 64 TNF2 IN32 2 63 TNF1 IN41 3 62 BNF11 61 BNF21 60 BNF12 TREBLE IN42 4 IN51 5 BASS IN52 6 59 BNF22 IN61 7 58 BBNF2 IN62 8 57 OUT2 IN71 9 56 BBNF1 55 OUT1 54 AGND8 53 AGND7 IN72 10 IN81 11 BASS BOOST 5.
PAGE 47
S-301 M66005-0001AHP (IC301: 1U-3681) SEG02 SEG01 SEG00 Vcc2 DIG15/SEG39 DIG14/SEG38 DIG13/SEG37 DIG12/SEG36 DIG11 DIG10 DIG09 DIG08 DIG07 DIG06 DIG05 DIG04 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 M66005-0001AHP SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 Vp SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 BLOCK DIAGRAM Display code RAM Bank 1 : 8bit x 16 Bank 2 : 8bit x 64 ・ CGROM (35bit x 160) code write CS 14 SCK 15 SDATA 16 XIN 21 XOUT 20
PAGE 48
S-301 AVDD_OSC XTL_IN XTL_OUT AVSS_OSC DVSS PWM_AP_1 PWM_AM_1 VALID_1 PWM_AP_2 PWM_AM_2 VALID_2 PWM_AP_3 PWM_AM_3 VALID_3 NC NC TAS5066 (IC805: 1U-3683) 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 NC MCLK_IN AVDD_PLL PLL_FLT_OUT PLL_FLT_RET AVSS_PLL NC DVSS1 RST ERR_RCVRY MUTE PDN SDA SCL CS0 DVSS1 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 DVDD_RCL DVSS_RCL NC DVDD_PWM DVSS_PWM PWM_AP_4 PWM_AM_4 VALID_4 PWM_AP_5 PWM_AM_5 VALID_5 P
PAGE 49
S-301 ADV7310 (IC302, 501: 1U-3692) 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 GND_IO CLKIN_B S9 S8 S7 S6 S5 DGND VDD S4 S3 S2 S1 S0 S_HSYNC S_VSYNC ADV7300 (MA: IC706) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 TOP VIEW 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 S_BLANK R SET 1 VREF COMP1 DAC A DAC B DAC C VAA AGND DAC D DAC E DAC F COMP2 R SET 2 EXT_LF RESET ADV7310 Terminal Function Pin No.
PAGE 50
S-301 SDEN SDATA SCLK V33 LCP LCN MNTR CE FE TE PI V25 V125 TPH DFT LINK CXD1881AR (IC802: 1U-3692) 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 RX 49 32 MEVO MEV 50 31 MIN VNA 51 30 MLPF FNN 52 29 MB FNP 53 28 MP DIP 54 27 MIRR DIN 55 26 LDON 25 VNB 24 CDPD VPA 58 23 DVDPD AIP 59 22 COLD AIN 60 21 DVDLD ATON 61 20 VC ATOP 62 19 VPB RFSIN 63 18 CD_E RFDC 64 17 CD_F BYP 56 8 DVDRFN A2 B2 C2 D2 CP CN 9 10 11 12 13
PAGE 51
S-301 RFAC 59 DIP AIP 60 DIN AIN 61 FNN ATON 62 FNP ATOP Block Diagram 53 52 55 54 57 FCCR b7-0 FBCR b6-0 AGC DVDRFP 1 DVDRFN 2 ATT MUX 4 RFSIN 63 SIGR b3 INPUT SEL RFCR b5-4 INPUT IMP SEL SSOUT RFCR b7-6 INPUT IMP SEL 56 BYP AGCO A D W/LPF GCA SIGR b2-0 12dB is added @ high gain mode (CDR b5=1) GCA MUX C 10 70kHz +/-6dB, 4bit Offset cancel LPF GCA +/-4dB A+C W/LPF GCA CD_B 15 CCR b4-0 FE offset 5 C B 11 Level DAC SUM Amp.
PAGE 52
S-301 Power Supply Pins Name I/O Function VPA - Power for RF and serial port VPB - Power for servo VNA - GND for RF and serial port VNB - GND for servo V33 - Power for output buffer V25 - Reference Power for servo output Input Pins Name I/O Function DVDRFP,DVDRFN I RF signal input RFSIN I RF signal input AIP,AIN I AGC amp.
PAGE 53
S-301 Analog Pins Name I/O Function BYP - RF AGC integration capacitor connecting terminal CP - Differential phase tracking LPF terminal CN - Differential phase tracking LPF terminal LCP - Lens shift offset cancel LPF terminal LCN - Lens shift offset cancel LPF terminal MP - MIRR top hold terminal MB - MIRR bottom hold terminal MEV - RFDC bottom envelope terminal MLPF - Mirror LPF terminal TPH - PI top hold terminal VC - Reference voltage output V125 - Reference voltag
PAGE 54
S-301 M12L64164A (IC103: 1U-3692) W986416DH (MA: IC103) VCC 1 DQ0 2 54 VSS 53 DQ15 VCCQ 3 52 VssQ DQ1 4 51 DQ14 DQ2 5 50 DQ13 VSSQ 6 49 VCCQ DQ3 7 48 DQ12 DQ4 8 47 DQ11 VCCQ 9 46 VSSQ DQ5 10 45 DQ10 DQ6 11 VSSQ 12 44 DQ9 43 VCCQ DQ7 13 42 DQ8 VCC 14 41 VSS LDQM 15 40 NC 39 UDQM WE 16 CAS 17 38 CLK RAS 18 37 CKE CS 19 36 NC BS0 20 35 A11 BS1 21 34 A9 A10/AP 22 33 A8 A0 23 32 A7 A1 24 31 A6 A2 25 A3 26 30 A5 29 A4 28 Vss Vcc 27 Terminal Function Pin No.
PAGE 55
S-301 IS42S16400B (IC201: 1U-3693) V DD DQ 0 V DDQ DQ 1 DQ 2 VSSQ DQ 3 DQ 4 VDDQ DQ 5 DQ 6 V SSQ DQ 7 V DD LDQM /W E /CAS /RAS /CS BA0 BA1 A10/A P A0 A1 A2 A3 V DD 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 V SS DQ15 V SSQ DQ14 DQ13 V DDQ DQ12 DQ 11 V SSQ DQ10 DQ 9 V DDQ DQ 8 V SS NC UD QM CLK CKE NC A11 A9 A8 A7 A6 A5 A4 V SS PIN DESCRIPTION PIN PIN NAME DESCRIPTION CLK Clock The system
PAGE 56
S-301 DGND CCLK COUT ASDATA ODVDD MCLK ALRCLK ABCLK DSDATA4 DSDATA3 DSDATA2 DSDATA1 DGND AD1837 (IC711: 1U-3694) 52 51 50 49 48 47 46 45 44 43 42 41 40 39 DVDD DVDD 1 38 DBCLK CLATCH 2 37 DLRCLK CIN 3 36 M/S PD/RST 4 35 AGND AGND 5 NC 6 34 OUTR4 TOP VIEW OUTL1 7 33 NC NC 8 32 OUTL4 OUTR1 9 31 NC AGND 10 30 AGND AVDD 11 29 AVDD NC 12 28 OUTR3 OUTL2 13 DVDD DVDD ODVDD 14 15 16 17 18 19 20 21 22 23 24 25 26 NC OUTR2 AGND FILTD FILTR AVDD A
PAGE 57
S-301 29 A6 28 A5 27 A4 26 VSS A2 23 VDD 25 A3 24 30 A7 A1 22 31 A8 A0 21 A10/AP 20 33 N.C 32 A9 BA 19 34 CKE CS 18 37 N.
PAGE 58
S-301 SM5819AF (IC608: 1U-3692) VSS EXIFLR EXICSW EXISLR EXILRCK EXIBCK VDDH EXIMCK VSS MCK TOUT2 VDDL 36 35 34 33 32 31 30 29 28 27 26 25 Pin Assignment 17 MCKOUT DIRDSCK 45 16 VSS SYNC 46 15 FMTPCM INIT 47 14 DIRPCK VSS 48 13 VDDL VSS 12 44 TOUT1 11 VDDH DSISR TEST3 10 18 9 43 TEST2 PBCK DSISL 8 19 TEST1 42 7 PLRCK DSISW VDDH 20 6 41 XMTPCM POSLR DSICT 5 21 DSGAIN 40 4 POCSW DSIFR SELEXT 22 3 39 SEL4FS POFLR DSIFL 2 VSS
PAGE 59
S-301 PIN DESCRIPTION No. Name I/O Property1 Input voltage 1 VDDL − − 2.5V Core power supply 2 SEL1FS I PD 3.3V PCM output rate select 1 L: 2fs/4fs, H: fs 3 SEL4FS I PD 3.3V PCM output rate select 2 L: 2fs, H: 4fs 4 SELEXT I PD 3.3V fs/2fs/4fs output and external data output select L: fs/2fs/4fs data, H: external data (EXI**) 5 DSGAIN I PD 3.3V DSD signal gain setting L: 100% modulation = 0dB, H: 50% modulation = 0dB 6 XMTPCM I PD 3.
PAGE 60
S-301 No. Name I/O Property1 Input voltage 39 DSIFL I − 3.3V DSD data input: front left-channel 40 DSIFR I − 3.3V DSD data input: front right-channel 41 DSICT I − 3.3V DSD data input: center channel Description 42 DSISW I − 3.3V DSD data input: subwoofer channel 43 DSISL I − 3.3V DSD data input: surround left-channel 44 DSISR I − 3.3V DSD data input: surround right-channel 45 DIRDSCK I PD 3.
PAGE 61
S-301 FAN8042 (IC803: 1U-3692) 42 41 40 39 PVCC1 43 PS 44 OPOUT2 VREF 45 OPIN2- SVCC 46 OPIN2+ OPOUT1 47 GND OPIN1- 48 GND OPIN1+ Pin Assignments 38 37 IN1+ 1 36 DO1+ IN1- 2 35 DO1- OUT1 3 34 DO2+ IN2+ 4 33 DO2- IN2- 5 32 DO3+ GND 6 31 GND GND 7 30 GND OUT2 8 29 DO3- IN3+ 9 28 DO4+ IN3- 10 27 DO4- OUT3 11 26 DO5+ 12 25 DO5- 17 18 19 20 OUT4 CTL FWD REV GND GND SGND 61 21 22 23 24 PVCC2 16 TSD-M 15 MUTE4 14 MUTE123
PAGE 62
S-301 Block Diagram SVCC OPIN1OPIN1+ OPOUT1 VREF GND 48 47 46 45 44 43 GND 42 OPOUT2 OPIN2+ OPIN2PS 41 40 39 38 POWER SAVE IN1+ 1 10K OUT1 3 10 K 10 K IN2+ 4 35 DO1- 40K 40K 40K 10K 10 K 10K GND 5 40K 10 K 10 K 33 DO2- 40K 40K 32 DO3+ 10 K 10K 6 34 DO2+ 10K 40K IN2- 36 DO1+ 40 K 2 IN1- PVCC1 37 40K 31 GND 40K 40K 10K 40K GND 7 30 GND 40K OUT2 8 10 K IN3+ 9 10 K 10 K IN3- 10 10 K 29 DO340K 40K 28 DO4+ 27 DO4- 40K OUT3 11 S M S C W IN4+ 12 + D - D MUTE123
PAGE 63
S-301 Pin Number Pin Name I/O 1 IN1+ I Pin Function Descrition CH1 op-amp input (+) 2 IN1- I CH1 op-amp input (-) 3 OUT1 O CH1 op-amp output 4 IN2+ I CH2 op-amp input (+) 5 IN2- I CH2 op-amp input (-) 6 GND - Ground 7 GND - Ground 8 OUT2 O CH2 op-amp output 9 IN3+ I CH3 op-amp input (+) CH3 op-amp input (-) 10 IN3- I 11 OUT3 O CH3 op-amp output 12 IN4+ I CH4 op-amp input (+) 13 IN4- I CH4 op-amp input (-) 14 OUT4 O CH4 op-amp output 15 CTL I CH5
PAGE 64
S-301 LC89057W (IC707: 1U-3694) 2 3 4 5 8 9 10 44 45 46 47 37 DO 36 RERR Input Selector Demodulation & Lock Detect Data Selector 21 RDATA 24 SDIN LPF 13 TMCK/PIO0 TBCK/PIO1 TLRCK/PIO2 TDATA/PIO3 Microcontroller I/F C bit, U bit XMODE 41 PLL Clock Selector Modulation or Parallel Port I/N 16 17 20 22 23 RMCK RBCK RLRCK SBCK SLRCK DO DI CE CL XMODE DGND DVDD TMCK/PIO0 TBCK/PIO1 TLRCK/PIO2 TDATA/PIO3 TXO/PIOEN TXO/PIOEN 48 29 XIN 28 XOUT 27 XMCK 37 38 39 40 41 42 43 44 45 46 47 48 TOP VIE
PAGE 65
S-301 Pin No. 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Pin Name XOUT XIN DVDD DGND EMPHA/UO AUDIO/VO CKST INT RERR DO DI CE CL XMODE DGND DVDD TMCK/PIO0 TBCK/PIO1 TLRCK/PIO2 TDATA/PIO3 TXO/PIOEN Function I/O O I — — I/O I/O I/O I/O O O I I I I — — I/O I/O I/O I/O O/I X’tal osc. connecting output terminal X’tal osc. connection, external clock input terminal (24.576MHz or 12.
PAGE 66
S-301 LH28F800BJE (IC907: 1U-3694) Y OFFSET SW DAC2 DAC1 DAC Vcc (5V) 41 PEDESTAL CLAMP C Vcc (5V) 42 Y DL 1H DL CONTROL SECAM CONTROL Y2 INPUT 25 㪛㪚㪛㪄㪪㪘㪈㪇 PEDESTAL CLAMP 24 SW GND HI: 20h/LOW: 24h SW YUV RGB MATRIX CW MATRIX SW TINT DEMO P / N ID LPF / fsc TRAP SW BPF NOSE DET V SEP H.
PAGE 67
S-301 CY7C1049CV-33-10ZC (IC908, 910: 1U-3694) Top View WE A5 A6 A7 A8 A9 NC NC NC NC NC A18 A17 A16 A15 OE I/O7 I/O6 VSS VCC I/O5 I/O4 A14 A13 A12 A11 A10 NC NC NC I/O0 INPUT BUFFER A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 I/O1 I/O2 SENSE AMPS CE I/O0 I/O1 VCC VSS I/O2 I/O3 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 ROW DECODER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 NC NC A0 A1 A2 A3 A4 512K x 8 ARRAY I/O3 I/O4 I/O5 POWER DOWN COLUMN DECODER CE I/O6 I/O7
PAGE 68
S-301 TAS5121 (IC101, 201, 301, 401: 1U-3683) GND PWM_BP GND RESET DREG_RTN GVDD M3 DREG DGND M1 M2 DVDD SD DGND OTW GND PWM_AP GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 GVDD_B GVDD_B GND BST_B PVDD_B PVDD_B OUT_B OUT_B GND GND OUT_A OUT_A PVDD_A PVDD_A BST_A GND GVDD_A GVDD_A 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 Terminal Functions TERMINAL NAME DKD FUNCTION(1) DESCRIPTION BST_A 22 P High-side bootstrap supply (BST), external resistor and capacitor to OUT_A required BST
PAGE 69
S-301 DSD1791DBR (IC118: 1U-3692) PLRCK PBCK PDATA DBCK SCK RST VDD DGND AGNDF VCCR AGNDR VOUTR– VOUTR+ VCOM 28 27 26 25 24 23 22 21 20 19 18 17 16 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 MS MC MDI DSDL DSDR ZEROL ZEROR VCCF VCCL AGNDL VOUTL– VOUTL+ AGNDC VCCC Block Diagram PLRCK ⋅8 Oversampling Digital Filter and Function Control DBCK DSDL DSDR RST Bias and Vref Current Segment DAC and I/V Buffer Function Control I/F MS VOUT R+ VOUT R– D/S and Filter System Clock Manager 69 VCCL AGNDC VCCF
PAGE 70
S-301 Terminal Functions TERMINAL I/O DESCRIPTIONS NAME PIN PLRCK 1 I Left and right clock (fs) input for PCM-format operation. WDCK clock input in external DF mode. Connected to ground in DSD mode (1) PBCK 2 I Bit clock input for PCM mode. Connected to GND for DSD mode (1) PDATA 3 I Serial audio data input for PCM mode (1) DBCK 4 I Bit clock input for DSD mode.
PAGE 71
S-301 BH7868FS (IC305: 1U-3692) (IC301, 302: 1U-3695) Vcc1 1 S1 2 6MHz LFP 75Ω S-DCOUT LPF 32 COUT 31 S-DCOUT 30 CVOUT 29 CVOUT 28 GND 27 YOUT 26 YOUT SAG 25 GND 24 Py/G OUT 23 Py/G OUT SAG 22 GND 21 Pb/B OUT 20 Pb/B OUT SAG 19 GND 18 Pr/R OUT 17 Pr/R OUT SAG L S2 3 CIN 4 MUTE1 5' CVIN 6 SEL (CV/MIX) 7 YIN 8 BIAS 9 SEL (BIAS/CLAMP) 10 6MHz LFP H 75Ω 6dB Bias MUTE1 Clamp Clamp 6MHz LFP 6dB 75Ω 6dB 12MHz LFP 6dB Bias Bias H Clamp L 75
PAGE 72
S-301 LC72720NM (IC506: 1U-3694) FLOUT VREF CIN Vddd Vdda 24 SYR Vref 1 REFERENCE VOLTAGE 23 CE MPXIN 2 Vdda 3 22 DI Vssa 4 21 CL CIN 6 CLOCK RECOVERY (1167.
PAGE 73
S-301 PCM1802 (IC803; 1U-3683) PCM1802 (TOP VIEW) 1 2 3 4 5 6 7 8 9 10 VINL VINR VREF1 VREF2 VCC AGND PDWN BYPAS FSYNC LRCK 20 19 18 17 16 15 14 13 12 11 MODE1 MODE0 FMT1 FMT0 OSR SCKI VDD DGND DOUT BCK block diagram VINL 5th Order Delta-Sigma Modulator Single-End /Differential Converter BCK LRCK 1/64 ( 1/128) Decimation Filter with DC Cut Filter VREF1 Reference VREF2 VINR Serial Interface DOUT Mode/ Format Control 5th Order Delta-Sigma Modulator Single-End /Differential Converter FSYNC FMT
PAGE 74
S-301 SM8701BM (IC113: 1U-3692) SM8701BM Terminal Function Pin Name Pin No. MLEN/R2 1 20 MCK/R1 P/S 2 19 MDT/R0 VDD 3 18 RSTN GND 4 17 SO3 XTO 5 16 VDDO XTI 6 15 GNDO GNDP 7 14 SO2 VDDP 8 13 SO4 VDD3 9 12 SO1 11 MON MO 10 I/O 1 MLEN/R2 Ip1 2 P/S Ip1 3 4 5 VDD GND XTO   O 6 XTI 7 8 9 10 11 12 13 14 15 16 17 18 GNDP VDDP VDD3 MO MON SO1 SO4 SO2 GNDO VDDO SO3 RSTN    O O O O O   O Ip2 I 19 MDT/R0 Ip1 20 MCK/R1 Ip1 Function Control signal input.
PAGE 75
S-301 SN74LV244APW (IC708, 719: 1U-3694) SN74HCT244APW (IC205: 1U-3694) OE I0 O4 I1 O5 I2 O6 I3 O7 GND 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 1A 2 SEL VSS 1 OE2 DATA 2 CLOCK 3 12-bit SHIFT REGISTER LCK 4 12-bit STRAGEREGISTER O1 Q0 5 I5 Q1 6 Q2 7 Q3 8 11 Q6 Q4 9 10 Q5 O0 I4 O2 I6 O3 CONTROL CIRCUIT 17 OE 16 Q11 15 Q10 14 Q9 OUTPUTBUFFER(OPENDRAIN) 13 Q8 12 Q7 I7 1Y 4 2A 5 12 4Y 2B 6 11 3A 2Y 7 10 3B GND 8 9 3Y SN74LVC139APWR (IC902:
PAGE 76
S-301 SN74CBTLV325PWB (IC209: 1U-3694) 1A (TOP VIEW) S 1B1 1B2 1A 2B1 2B2 2A GND 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 VCC OE 4B1 4B2 4A 3B1 3B2 3A 4 2 SW 3 SW 2A 7 5 SW 6 SW 3A 9 11 SW 10 SW 4A 12 14 SW 13 SW S OE 1B1 1B2 2B1 2B2 3B1 3B2 4B1 4B2 1 15 NJM2595 (IC507, 508: 1U-3695) 16 9 1 8 BU4053BCF (IC510: 1U-3695) BU4052BCF (IC518: 1U-3695) 16 VDD Y0 1 Y 15 Y Y2 2 Z1 X 14 X COMMON Y 3 Z X1 13 X1 Y3 4 Z0 X0 12 X0 Y1 5 Y1 1 Y0 2 Y0 Y
PAGE 77
S-301 MIC2025 (IC102: 1U-3693) Pin Description MIC2025/75 EN Pin Number Pin Name 1 EN Switch Enable (Input): Active-high (-1) or active-low (-2). 2 FLG Fault Flag (Output): Active-low, open-drain output. Indicates overcurrent or thermal shutdown conditions. Overcurrent condition must exceed tD in order to assert FLG.
PAGE 78
S-301 CY2302 (IC115: 1U-3692) Block Diagram Pin Configuration FBIN 1 8 OUT2 IN 2 7 VDD GND 3 6 OUT1 FS0 4 5 FS1 External feedback connection to OUT1 or OUT2, not both FBIN FS0 ÷Q FS1 Configuration Options FBIN FS0 FS1 OUT1 OUT2 OUT1 0 0 2 X REF REF OUT1 1 0 4 X REF 2 X REF OUT1 0 1 REF REF/2 OUT1 1 1 8 X REF 4 X REF OUT2 0 0 4 X REF 2 X REF OUT2 1 0 8 X REF 4 X REF OUT2 0 1 2 X REF REF OUT2 1 1 16 X REF 8 X REF Phase Detector IN Reference
PAGE 79
S-301 BD9781HFP (IC810: 1U-3695) 5~35V 1 EN/SYNC V IN ON/OFF 1μF 220μF Vref SOFT START 24KΩ BD9781HVFP INV COMPARATOR LATCH 150KΩ Vref 2 3 4 5 6 DRIVER SW 33μH 330μF TSD OSC 7 V IN CURRENT LIMIT 4 GND 5 FB 3 RT 390KΩ 0.
PAGE 80
S-301 SN74LVC2G14 (IC113: 1U-3693) LOGIC DIAGRAM (POSITIVE LOGIC) 1A GND 2A 1 6 2 5 3 4 1Y VCC 2Y 1A 2A 1 6 3 4 1Y 2Y STR-F6238S (IC902: 1U-3682: E3) STR-F6267S (IC902: 1U-3682: E2) 3 D 4 V IN DR V .R E G S tart Latch O.V .P R g3 R eg. FRONT VIEW R g2 R g1 DR V T .S .D. 2 G ND 1 O.C .P O.C .P O.L.P O.C.P. G ND D VIN F .B O. S . C INH1 INH2 C urre nt M ir r o r F .B 5 F .B TC7S08F (IC806: 1U-3692) BD4828G (IC203: 1U-3694) LM3671 (IC912: 1U-3694) VIN 1 5 N.C .
PAGE 81
S-301 SI-8120E (IC901: 1U-3682) BA00BCOWFP (IC304: 1U-3681) KIA78R00API (IC208: 1U-3694) VIN SWOUT GND VOS ON/OFF FRONT VIEW 12345 1. CLT 2. Vcc 3. N.C. 4. OUT 5. N.C. FIN:GND BA18BCOFP (IC402, 605: 1U-3692) BA25BCOFP (IC401, 604: 1U-3692) BA50BCOFP (IC703: 1U-3692) BA33B00FP (IC207: 1U-3694) NJM7809DL (IC505: 1U-3695) 1234 PC123 (IC906: 1U-3682) 4 TOP VIEW ANODE CATHODE 1 VCC 2 N.C 3 OUT 1 2 3 4 GND LM1117MPX-1.
PAGE 82
S-301 NJM7912FA (IC807: 1U-3695) (IC905: 1U-3682) LM2990T-5.0 (IC809: 1U-3695) SE-B2 (IC908: 1U-3682) C 2 FRONT VIEW 1 REF Common Input Ou tpu t REF COLLECTOR GROUND FRONT VIEW NJM78L07UA (IC512: 1U-3694) 3 GND NJM79L07AU (IC513: 1U-3694) 3 IN 3 OUT 2 GND 2 IN 1 OUT 1 COMMON BA05T (IC907: 1U-3682) BA033T (IC904: 1U-3682) NJM7805FA (IC712: 1U-3694) (IC801: 1U-3695) NJM7812FA (IC909: 1U-3682) (IC806: 1U-3695) LM2940CT-5.
PAGE 83
S-301 2.
PAGE 84
S-301 PRINTED WIRING BOARDS 1U-3692 DVD MECHA P.W.B.
PAGE 85
S-301 FOIL SIDE 85
PAGE 86
S-301 1U-3693 USB P.W.B.
PAGE 87
S-301 1U-3694 MAIN P.W.B.
PAGE 88
S-301 FOIL SIDE 88
PAGE 89
S-301 1U-3695 I/F P.W.B.
PAGE 90
S-301 FOIL SIDE 90
PAGE 91
S-301 1U-3681 DISPLAY P.W.B.
PAGE 92
S-301 FOIL SIDE 92
PAGE 93
S-301 1U-3682 SMPS P.W.B.
PAGE 94
S-301 FOIL SIDE 94
PAGE 95
S-301 1U-3683 AMP P.W.B.
PAGE 96
S-301 FOIL SIDE 96
PAGE 97
S-301 NOTE FOR PARTS LIST 部品表について • Part indicated with the mark "nsp" are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused. • When ordering of part, clearly indicate "1" and "I" (i) to avoid missupplying. • Ordering part without stating its part number can not be supplied. • Part indicated with the mark " ★ " is not illustrated in the exploded view. • Not including Carbon Film Resister ±5%, 1/4W Type in the P.W.
PAGE 98
S-301 PARTS LIST OF P.W.B. UNIT ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. ＊ "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。＊ Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
PAGE 99
S-301 Ref. No. nsp Part No.
PAGE 100
S-301 Ref. No. nsp TH201 Part No.
PAGE 101
S-301 nsp Part No. C164-166 Ref. No.
PAGE 102
S-301 Ref. No. nsp Part No.
PAGE 103
S-301 Ref. No. nsp Part No.
PAGE 104
S-301 nsp Part No. C685 Ref. No.
PAGE 105
S-301 Ref. No. nsp C791,792 C793,794 nsp C795,796 C797 nsp C798 Part No.
PAGE 106
S-301 Ref. No. nsp C942 Part No.
PAGE 107
S-301 Ref. No. nsp ST201 Part No. - ST701-704 - T101 00D 231 8080 008 Part Name - 2P WIRE W711A,712A - 2P WIRE W713,714 - 2P WIRE W713A,714A - 2P WIRE nsp 00D 205 1034 007 Q'ty New STYLE PIN D/D TRANS(040525510A W711,712 W852 Remarks STYLE PIN * M3 SCREW TERMINAL X201 00D 399 0805 914 CSTLS16M0X51-A0 X501 00D 399 0178 007 X-TAL(4.332MHZ) X701 00D 399 1016 003 X-TAL(12.288MHZ) * X901 00D 399 1011 008 X-TAL(18.
PAGE 108
S-301 00D1U-3695A/B/C I/F P.W.B. UNIT ASS'Y Ref. No. nsp Part No.
PAGE 109
S-301 Ref. No. nsp Part No.
PAGE 110
S-301 Ref. No. nsp Part No.
PAGE 111
S-301 Ref. No. nsp Part No.
PAGE 112
S-301 Ref. No. CY131 nsp Part No.
PAGE 113
S-301 00D1U-3681A DISPLAY P.W.B. UNIT ASS'Y Ref. No. nsp Part No.
PAGE 114
S-301 nsp Part No. C332 Ref. No.
PAGE 115
S-301 Ref. No. nsp FL301 Part No.
PAGE 116
S-301 00D1U-3682A/B/C SMPS P.W.B. UNIT ASS'Y Ref. No. nsp Part No.
PAGE 117
S-301 Ref. No. nsp Part No.
PAGE 118
S-301 Ref. No. nsp Part No. nsp 00D 257 0512 903 C963,964 nsp 00D 257 0516 909 CK73B1E223KT +1608 C965,966 nsp 00D 257 0511 904 CK73F1H103ZT +1608 C967 nsp 00D 257 0512 903 CK73F1E104ZT +1608 C968 nsp 00D 257 0511 904 CK73F1H103ZT +1608 C962 Part Name CK73F1E104ZT Remarks Q'ty New +1608 OTHERS PARTS GROUP CX021 nsp 00D 205 0581 001 2P VH CONNECTOR BASE CY041 nsp 00D 205 0653 049 4P VH CON.
PAGE 119
S-301 00D1U-3683A AMP P.W.B. UNIT ASS'Y Ref. No. nsp Part No.
PAGE 120
S-301 Ref. No. C112 nsp Part No.
PAGE 121
S-301 Ref. No. nsp C542,543 C544 nsp C545 C546 nsp C547 Part No.
PAGE 122
S-301 Ref. No. nsp C835 Part No.
PAGE 123
S-301 Ref. No. nsp Part No. Part Name Remarks Q'ty New L301,302 00D 231 0091 008 60NH(AIR COIL) * L303,304 00D 235 0188 007 INDUCTOR DAL2210-4R7 * L401,402 00D 231 0091 008 60NH(AIR COIL) * L403,404 00D 235 0188 007 INDUCTOR DAL2210-4R7 * L801 00D 235 0070 911 INDUCTOR(220)ST RL801,802 00D 214 0217 007 RELAY(DS24D2) W501 - LUG PLATE W801 - LUG PLATE W803,804 - LUG PLATE X801 nsp 00D 399 1017 002 X-TAL(24.
PAGE 124
S-301 00D1U-3692A/B/C DVD MECHA P.W.B. UNIT ASS'Y Ref. No. nsp Part No.
PAGE 125
S-301 Ref. No. nsp TR509 Part No.
PAGE 126
S-301 Ref. No. nsp Part No.
PAGE 127
S-301 nsp Part No. C194 Ref. No.
PAGE 128
S-301 Ref. No. C347 nsp Part No.
PAGE 129
S-301 nsp Part No. C511,512 Ref. No.
PAGE 130
S-301 Ref. No. C704 nsp Part No.
PAGE 131
S-301 nsp Part No. C814,815 Ref. No.
PAGE 132
S-301 nsp Part No. C924 Ref. No.
PAGE 133
S-301 Ref. No. FB401 nsp Part No.
PAGE 134
S-301 00D1U-3693A USB P.W.B. UNIT ASS'Y Ref. No. nsp Part No.
PAGE 135
S-301 Ref. No. nsp JK311 W302 X131 nsp Part No. Part Name 00D 204 8714 000 USB CONNECTOR(TOPYANG BLACK) 00D 205 1034 010 M3 SCREW TERMINAL 00D 399 1030 908 HC-49/U03C24.
PAGE 136
S-301 EXPLODED VIEW WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
PAGE 137
S-301 PARTS LIST OF EXPLODED VIEW ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. ＊ "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。＊ Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
PAGE 138
S-301 Ref. No. nsp Part No.
PAGE 139
S-301 Ref. No. nsp Part No. ★ 82 nsp 00D 513 4101 003 CAUTION LABEL Part Name Remarks ★ 91 nsp 00D 203 5372 002 3P ZH-PH CON.CORD ★ 92 nsp 00D 203 8567 005 5P PH-PH CON.CORD ★ 93 nsp 00D 203 8568 004 5P PH-PH CON.CORD ★ 94 nsp 00D 203 8571 004 5P PH-PH USB WIRE 1 * ★ 95 nsp 00D 204 0570 035 6P PH-PH SHIELD CORD 1 * ★ 96 nsp 00D 204 0599 003 6P PH-PH CON.CORD 1 * ★ 97 nsp 00D 204 2996 002 7P PH-PH CON.CORD 1 * ★ 98 nsp 00D 204 2997 001 10P ZH-PH CON.
PAGE 140
S-301 EXPLODED VIEW OF DVD MECHANISM 14 26 3 46 47 26 32 47 31 30 63 8 32 44 38 2 72 43 12 37 15 39 33 34 28 50 42 43 35 21 21 70 36 52 29 1 6 23 27 52 51 5 23 51 71 7 49 24 49 11 49 48 23 24 24 54 49 27A 24 9 10 17 16 68 24 4 25 18 64 20 19 22 140 53 50 40 41
PAGE 141
S-301 PARTS LIST OF DVD MECHANISM UNIT ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. ＊ "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。＊ Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused. 00D 337 0133 109 DVD MECHA (TD-5HP-DE) Ref. No.
PAGE 142
S-301 Ref. No. nsp Part No. Part Name Remarks Q'ty 41 - FEED MOTOR ASS'Y 1 50 - POLY.SLIT WASHER 2.1X4X0.25C 2 53 - FEED GEAR 3RD 1 49 00D 9KC 1G04 3 DAMPER 4 51 - SPECIAL SCREW (FRONT) 2 SPECIAL SCREW (REAR) 2 52 - 54 00D 9KB 7P02 4 TRAY-SPRING-VXF 1 64 00D 9KC 1G04 2 RUBBER CUSHION 2 68 - TAPE W10X45 (NITTO NO.
PAGE 143
S-301 POINTS OF GREASING With Cemedine 575, glue 3 joint parts of Clamper-L and H hooks. (0.05mg each x 3) *As for greasing to the R rail groove and groove's side edge, apply grease to the outer face "intentionally". (Not only running a brush into the groove, use it with pressing to the outer face consciously.) After attaching cushions, apply Cemedine 575 to the joint parts of the cushions and tabs (both sides, left and right) from the tab's back side. (0.
PAGE 144
S-301 DSW-S301 EXPLODED VIEW 105 1A 28 105 102 25 11 24 105 12 22 105 105 99 37 26 23 33 106 105 22 105 107 22 11 66 x4 21 35 102 34 44 27 101 105 77 88 33 x4 55 x4 105 14 x8 32 105 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
PAGE 145
S-301 DSW-S301 PARTS LIST OF EXPLODED VIEW ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. ＊ "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。＊ Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
PAGE 146
S-301 Ref. No. nsp Part No. ★ 44 nsp 00D 461 1238 021 Part Name Remarks ★ 45 nsp 00D 461 1238 034 PEF SHEET(10X280) ★ 46 nsp 00D 513 4082 009 RATING LABEL(S301E3) for E3 1 * ★ 46 nsp 00D 513 4083 008 RATING LABEL(S301E2) for E2 1 * ★ 46 nsp 00D 513 4084 007 RATING LABEL(JPN) for JP 1 ★ 48 nsp 00D 513 4093 001 DANGEROUS LABEL for E3 1 ★ 51 nsp 00D 203 6629 000 4P EH-EH CON.CORD 1 ★ 52 nsp 00D 204 2993 005 7P EH-EH CON.
PAGE 147
S-301 SC-S301 EXPLODED VIEW 10L for Lch 10R for Rch 147 9L for Lch 9R for Rch 13L for Lch 13R for Rch
PAGE 148
S-301 SC-S301 PARTS LIST OF EXPLODED VIEW ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. ＊ "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。＊ Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused.
PAGE 149
S-301 Ref. No. nsp Part No.
PAGE 150
S-301 PACKING VIEW 114 112 DVD SURROUNDRECIEVER ADV-S301 135 109 113 110 ACCESSORY BOX ASSY 111 SPEAKER SYSTEM SCS301SRM 104 103 105 SUB WOOFER 106 107 108 101 102 MASTER CARTON PARTS LIST OF PACKING & ACCESSORIES ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions.
PAGE 151
S-301 Ref. No. nsp Part No.
PAGE 152
S-301 WIRING DIAGRAM (1) S301 DSW-S301 SC-S301 ADV-S301 SC-S301 A B ITEM A B PART NO. 00D2046794006 00D2032439003 B PART NAME 25P D-SUB CABLE SP CABLE ASSY (2) DSW-S301 IN/OUT UNIT 1U-3683A-2 CX111 CX151 C1 C2 CY111 SMPS UNIT 1U-3682A(E3) 1U-3682B(E2) 1U-3682C(J) CX021 CX043 CX041 CX101 CX071 C6 C7 C8 C9 C3 CY031 C4 CY042 CX043 CX041 CX101 CX071 CX022 C10 SUB WOOFER UNIT AC INLET PART NO.
PAGE 153
S-301 (2) ADV-S301 DSW-S101 CY251 LOCAL POWER UNIT 1U-3695A-1(E3) 1U-3695B-1(E2) 1U-3695C-1(J) FAN CY072(E2) CONVERT UNIT 㧰3 CX061(E2) CX173 㧰1 㧰4 㧰5 CX162 (Board to Board) (Board to Board) CX051(E3) DVD UNIT 1U-3692A(E3) 1U-3692B(E2) 1U-3692C(J) 1U-3695A-2(E3) 1U-3695B-2(E2) 1U-3695C-2(J) CX161 㧰6 CX065 㧰2 CX141 (Board to Board) I/F BOARD UNIT CX073(E2) CY173 CY033 CX162 CY065 CX051(E3) CY061(E2) 1U-3695A-3(E3) 1U-3695B-3(E2) 1U-3695C-3(J) TUNER PACK (Board to Board) CX131
PAGE 154
S-301 ITEM D1 D2 D3 D4 D5 D6 D7 D8 D13 D14 D16 D17 D18 D19 D20 D21 D22 PART NO. 00D2035372002 00D2040599003 00D2048567005 00D0090265004 00D2040570022 00D2042996002 00D0090236020 00D2042997001 00D0090231012 00D0090233078 00D2038569003 00D2048568004 00D0090236065 00D2046800000 00D0090266003 00D0090227013 00D2038571004 PART NAME 3P ZH-PH CON.CORD 6P PH-PH CON.CORD 5P PH-PH CON.CORD 17P FFC CABLE 6P PH-PH SHIELD CORD 7P PH-PH CON.CORD 15P FFC CABLE 10P ZH-PH CON.
PAGE 155
S-301 WAVEFORMS ● 1U-3692 DVD PLAY Disc: TDV-520A CD PLAY DISC DETECT (CD) ③FSCON ⑥TE ②FE ①RFAC VC16 ⑦TSCON ⑧T+ ⑯PI ⑨T- CD PLAY ⑰MIRR DVD PLAY (INNER) Disc: TCD-784 ⑩DMO ①RFAC VC16 ⑪FG ⑫A3 DVD LOADING PLAY CD PLAY (INNER) ②FE ⑩DMO ③FSCON ④F+ ⑪FG ⑫A3 ⑤F- CD LOADING PLAY SEARCH TO OUTER CHAPTER (INNER ②FE ⑥TE ③FSCON ④F+ ⑬SLED ⑤F- ⑭SL+ ⑮SL- DVD PLAY ⑥TE DISC DETECT (DVD) ③FSCON ②FE ⑦TSCON ⑧T+ ⑨T- ⑯PI ⑰MIRR 155 OUTER)
PAGE 156
S-301 NOTE FOR SCHEMATIC DIAGRAM 配線図について WARNING: Parts marked with this symbol ! have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. ! 印の部品は安全を維持するために重要な部品です。従って交換時は必ず指定の部品を使用してください。注） CAUTION: (1) 指定なき抵抗値は Ω、ｋはｋΩ、M は MΩ を示す。 Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.
PAGE 157
S-301 SCHEMATIC DIAGRAMS (1/50) 1 2 3 4 5 6 7 8 9 10 11 1 2 6 A 16 B C D 13 8 15 7 SLD- 9 3 SLD+ E 14 4 5 F G 11 12 SIGNAL LINE 10 SCHEMATIC DIAGRAMS (1/50) 1U-3692 DVD/VIDEO UNIT (1/7) (E3 model only) H 157
PAGE 158
S-301 SCHEMATIC DIAGRAMS (2/50) 1 2 3 4 5 6 7 8 9 10 11 1 2 6 A 16 B C D 13 8 15 7 SLD- 9 3 SLD+ E 14 4 5 F G 11 12 SIGNAL LINE 10 SCHEMATIC DIAGRAMS (2/50) 1U-3692 DVD/VIDEO UNIT (1/7) (E2 model only) H 158
PAGE 159
S-301 SCHEMATIC DIAGRAMS (3/50) 1 2 3 4 5 6 7 8 9 10 11 1 2 6 A 16 B C D 13 8 15 7 SLD- 9 3 SLD+ E 14 4 5 F G 11 12 SIGNAL LINE 10 SCHEMATIC DIAGRAMS (3/50) 1U-3692 DVD/VIDEO UNIT (1/7) (JP model only) H 159
PAGE 160
S-301 SCHEMATIC DIAGRAMS (4/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (4/50) 1U-3692 DVD/VIDEO UNIT (2/7) (E3 model only) H 160
PAGE 161
S-301 SCHEMATIC DIAGRAMS (5/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (5/50) 1U-3692 DVD/VIDEO UNIT (2/7) (E2 model only) H 161
PAGE 162
S-301 SCHEMATIC DIAGRAMS (6/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (6/50) 1U-3692 DVD/VIDEO UNIT (2/7) (JP model only) H 162
PAGE 163
S-301 SCHEMATIC DIAGRAMS (7/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (7/50) 1U-3692 DVD/VIDEO UNIT (3/7) (E3 model only) H 163
PAGE 164
S-301 SCHEMATIC DIAGRAMS (8/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (8/50) 1U-3692 DVD/VIDEO UNIT (3/7) (E2 model only) H 164
PAGE 165
S-301 SCHEMATIC DIAGRAMS (9/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (9/50) 1U-3692 DVD/VIDEO UNIT (3/7) (JP model only) H 165
PAGE 166
S-301 SCHEMATIC DIAGRAMS (10/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (10/50) 1U-3692 DVD/VIDEO UNIT (4/7) (E3 model only) H 166
PAGE 167
S-301 SCHEMATIC DIAGRAMS (11/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (11/50) 1U-3692 DVD/VIDEO UNIT (4/7) (E2 model only) H 167
PAGE 168
S-301 SCHEMATIC DIAGRAMS (12/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (12/50) 1U-3692 DVD/VIDEO UNIT (4/7) (JP model only) H 168
PAGE 169
S-301 SCHEMATIC DIAGRAMS (13/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (13/50) 1U-3692 DVD/VIDEO UNIT (5/7) (E3 model only) H 169
PAGE 170
S-301 SCHEMATIC DIAGRAMS (14/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (14/50) 1U-3692 DVD/VIDEO UNIT (5/7) (E2 model only) H 170
PAGE 171
S-301 SCHEMATIC DIAGRAMS (15/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (15/50) 1U-3692 DVD/VIDEO UNIT (5/7) (JP model only) H 171
PAGE 172
S-301 SCHEMATIC DIAGRAMS (16/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (16/50) 1U-3692 DVD/VIDEO UNIT (6/7) H 172
PAGE 173
S-301 SCHEMATIC DIAGRAMS (17/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (17/50) 1U-3692 DVD/VIDEO UNIT (7/7) (E3 model only) H 173
PAGE 174
S-301 SCHEMATIC DIAGRAMS (18/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (18/50) 1U-3692 DVD/VIDEO UNIT (7/7) (E2 model only) H 174
PAGE 175
S-301 SCHEMATIC DIAGRAMS (19/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (19/50) 1U-3692 DVD/VIDEO UNIT (7/7) (JP model only) H 175
PAGE 176
S-301 SCHEMATIC DIAGRAMS (20/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (20/50) 1U-3693 USB UNIT (1/2) H 176
PAGE 177
S-301 SCHEMATIC DIAGRAMS (21/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (21/50) 1U-3693 USB UNIT (2/2) H 177
PAGE 178
S-301 SCHEMATIC DIAGRAMS (22/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (22/50) 1U-3694 AUDIO UNIT (1/5) (E3 model only) H 178
PAGE 179
S-301 SCHEMATIC DIAGRAMS (23/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (23/50) 1U-3694 AUDIO UNIT (1/5) (E2 model only) H 179
PAGE 180
S-301 SCHEMATIC DIAGRAMS (24/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (24/50) 1U-3694 AUDIO UNIT (1/5) (JP model only) H 180
PAGE 181
S-301 SCHEMATIC DIAGRAMS (25/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (25/50) 1U-3694 AUDIO UNIT (2/5) H 181
PAGE 182
S-301 SCHEMATIC DIAGRAMS (26/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (26/50) 1U-3694 AUDIO UNIT (3/5) (E3 model only) H 182
PAGE 183
S-301 SCHEMATIC DIAGRAMS (27/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (27/50) 1U-3694 AUDIO UNIT (3/5) (E2 model only) H 183
PAGE 184
S-301 SCHEMATIC DIAGRAMS (28/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (28/50) 1U-3694 AUDIO UNIT (3/5) (JP model only) H 184
PAGE 185
S-301 SCHEMATIC DIAGRAMS (29/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (29/50) 1U-3694 AUDIO UNIT (4/5) (E3 model only) H 185
PAGE 186
S-301 SCHEMATIC DIAGRAMS (30/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (30/50) 1U-3694 AUDIO UNIT (4/5) (E2 model only) H 186
PAGE 187
S-301 SCHEMATIC DIAGRAMS (31/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (31/50) 1U-3694 AUDIO UNIT (4/5) (JP model only) H 187
PAGE 188
S-301 SCHEMATIC DIAGRAMS (32/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (32/50) 1U-3694 AUDIO UNIT (5/5) H 188
PAGE 189
S-301 SCHEMATIC DIAGRAMS (33/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (33/50) 1U-3695-3 CONVERT UNIT (1/2) (E3 model only) H 189
PAGE 190
S-301 SCHEMATIC DIAGRAMS (34/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (34/50) 1U-3695-3 CONVERT UNIT (1/2) (E2 model only) H 190
PAGE 191
S-301 SCHEMATIC DIAGRAMS (35/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (35/50) 1U-3695-3 CONVERT UNIT (1/2) (JP model only) H 191
PAGE 192
S-301 SCHEMATIC DIAGRAMS (36/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (36/50) 1U-3695-3 CONVERT UNIT (2/2) (E3 model only) H 192
PAGE 193
S-301 SCHEMATIC DIAGRAMS (37/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (37/50) 1U-3695-3 CONVERT UNIT (2/2) (E2 model only) H 193
PAGE 194
S-301 SCHEMATIC DIAGRAMS (38/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (38/50) 1U-3695-3 CONVERT UNIT (2/2) (JP model only) H 194
PAGE 195
S-301 SCHEMATIC DIAGRAMS (39/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (39/50) 1U-3695-1 LOCAL POWER UNIT (E3 model only) H 195
PAGE 196
S-301 SCHEMATIC DIAGRAMS (40/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (40/50) 1U-3695-1 LOCAL POWER UNIT (E2 model only) H 196
PAGE 197
S-301 SCHEMATIC DIAGRAMS (41/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (41/50) 1U-3695-1 LOCAL POWER UNIT (JP model only) H 197
PAGE 198
S-301 SCHEMATIC DIAGRAMS (42/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (42/50) 1U-3695-2 I/F BOARD UNIT H 198
PAGE 199
S-301 SCHEMATIC DIAGRAMS (43/50 ) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (43/50) 1U-3681-1 DISPLAY CENTER UNIT 1U-3681-2 DISPLAY RIGHT UNIT 1U-3681-3 DISPLAY LEFT1 UNIT 1U-3681-4 DISPLAY LEFT2 UNIT 1U-3681-5 DISPLAY H/P OUT UNIT 1U-3681-8 DISPLAY AUX UNIT H 199
PAGE 200
S-301 SCHEMATIC DIAGRAMS (44/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (44/50) 1U-3681-11 iPOD in UNIT H 200
PAGE 201
S-301 SCHEMATIC DIAGRAMS (45/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (45/50) 1U-3682-1 SMPS UNIT (E3 model only) H 201
PAGE 202
S-301 SCHEMATIC DIAGRAMS (46/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (46/50) 1U-3682-1 SMPS UNIT (E2 model only) H 202
PAGE 203
S-301 SCHEMATIC DIAGRAMS (47/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SCHEMATIC DIAGRAMS (47/50) 1U-3682-1 SMPS UNIT (JP model only) H 203
PAGE 204
S-301 SCHEMATIC DIAGRAMS (48/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (48/50) 1U-3683A-2 IN/OUT UNIT 1U-3683A-3 TERMINAL UNIT H 204
PAGE 205
S-301 SCHEMATIC DIAGRAMS (49/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (49/50) 1U-3683A-1 AMP UNIT (1/2) H 205
PAGE 206
S-301 SCHEMATIC DIAGRAMS (50/50) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (50/50) 1U-3683A-1 AMP UNIT (2/2) H 206
PAGE 207
S-301 DOCUMENTS FOR WEEE Details of Recycle Parts ＊ You have to remove the parts that marked “WEEE Mark ◆ ” when the recycling processing. (Europe model only) Recycle Parts for ADV-S301 Ref. No.
PAGE 208
S-301 Ref. No. WEEE Mark Part Name Material Q'ty 48 49 50 51 52 53 54 EMI G.
PAGE 209
S-301 Ref. No. 36 37 38 39 40 41 WEEE Mark Part Name Material Q'ty FERRITE CORE EARTH BRACKET POWER TRANS POWER TRANS CE68W2G331M35(KMM) FERRITE CRAMP081610N Complex STEEL Complex Complex Complex Complex 1 1 1 1 1 1 51 52 53 54 55 56 57 58 59 4P EH-EH CON.CORD 7P EH-EH CON.CORD 10P EH-EH CON.CORD 4P VH-VH CON.CORD 2P VH CON.CORD 3P EH-EH CON.CORD 4P VH-VH CON.CORD 11P EH-EH CON.CORD 15P PH-PH CON.
PAGE 210
S-301 Exploded view of ADV-S301 104 You have to remove the parts that marked "WEEE mark " when the recycling processing.
PAGE 211
S-301 Exploded view of DSW-S301 55 You have to remove the parts that marked "WEEE mark " when the recycling processing.
PAGE 212
S-301 Exploded view of SC-S301 You have to remove the parts that marked "WEEE mark " when the recycling processing.
PAGE 213
S-301 Details of Recycle parts for Power transformer Part No.38 : POWER TRANS No. Material 1 STEEL 2 STEEL 3 PA 4 PET 5 COPPER WIRE 6 COPPER WIRE 7 PBT 8 COPPER 9 COPPER Part No.39 : POWER TRANS No.