Manualshelf

Owner`s manual

ManualsBrandsDenon Manualsaudio & home theatreRCD-N8
11121314151617181920
14
Setting the general [General]
Speaker Optimization
An optimizing filter suited for the properties of the speakers (SC-N8)
can be used.
1
Press SETUP.
Turns on the Menu settings mode
and the Menu appears on the display
(vpage11 “Menu map”).
ADD
CALL
FAVORITE
SEARCH
. / ABC
DEF
GHI JKL
MNO
PQRS TUV WXYZ
1 2 3
4 5 6
7 8 9
VOLUME
SDB
TONE
MUTE
TOP MENU INFO
ENTER
SETUP
2
Use ui and ENTER to
select “General” – “Speaker
Optimization”, then press
ENTER or p.
“Speaker Optimization” menu appears.
3
Use ui to select “On”, then
press ENTER or p.
ON
The response is optimized for the speakers (SC-N8, sold
separately).
OFF
The response is flat.
Language
Sets the language for display the menu.
•The factory language setting is “English”.
1
Press SETUP.
Turns on the Menu settings mode
and the Menu appears on the display
(vpage11 “Menu map”).
ADD
CALL
FAVORITE
SEARCH
. / ABC
DEF
GHI JKL
MNO
PQRS TUV WXYZ
1 2 3
4 5 6
7 8 9
VOLUME
SDB
TONE
MUTE
TOP MENU INFO
ENTER
SETUP
2
Use ui and ENTER to select
“General” – “Language”, then
press ENTER or p.
English
/
Deutsch
/
Français
/
Italiano
/
Nederlands
/
Español
/
Svenska
Auto-Standby
When this unit is in the stop state and there is no input signal and
operation for 30 minutes, it automatically enters the standby mode.
For the input source “Analog In 1”, “Analog In 2” and “Portable
In” only, when no operation is performed for eight hours, this unit
automatically enters the standby mode.
•The default setting is “On”.
1
Press SETUP.
Turns on the Menu settings mode
and the Menu appears on the display
(vpage11 “Menu map”).
ADD
CALL
FAVORITE
SEARCH
. / ABC
DEF
GHI JKL
MNO
PQRS TUV WXYZ
1 2 3
4 5 6
7 8 9
VOLUME
SDB
TONE
MUTE
TOP MENU INFO
ENTER
SETUP
2
Use ui and ENTER to select
“General” – “Auto-Standby”,
then press ENTER or p.
“Select Auto-Standby” menu appears.
3
Use ui to select “On”, then
press ENTER or p.
The setting is entered.
NOTE
In the following situations, the Auto-standby function does not operate.
•When the source is “Tuner”, “iPod” (Remote mode) or “AirPlay”.
•During CD playback or pause.
Firmware
n Update
•In order to update the firmware, the environment and settings
required for connecting to broadband internet are needed
(vpage9).
•Perform the firmware update operation after at least 2 minutes has
elapsed since turning this unit’s power ON.
1
Press SETUP.
Turns on the Menu settings mode
and the Menu appears on the display
(vpage11 “Menu map”).
ADD
CALL
FAVORITE
SEARCH
. / ABC
a
/
A
DEF
GHI JKL
MNO
PQRS TUV WXYZ
*
1 2 3
4 5 6
7 8 9
+10 0
RC-1174
CH
-
+
CH
TUNE +TUNE
-
ANALOG IN
TUNER
DIGITAL IN
POWER
CLOCK DIMMERSLEEP
MUSIC
SERVER
INTERNET
RADIO
ONLINE
MUSIC
VOLUME
SDB
TONE
MUTE
TOP MENU INFO
MODE
CLEAR
USB
iPod CD
RANDOM
REPEAT PROGRAM
ENTER
SETUP
2
Use ui and ENTER to select
“General” – “Firmware” –
“Update”, then press ENTER or
p.
Check For Update
Check for firmware updates. You can also check
approximately how long it will take to complete
an update.
Update Start Execute the update process.
•If updating fails, the set automatically retries, but if updating is still
not possible, one of the messages shown below is displayed. If
the display reads as shown below, check the settings and network
environment, then update again.
Display Description
Updating fail Updating failed.
Login failed Failure to login to server.
Server is busy Server is busy. Wait a while then try again.
Connection fail Failure in connecting to server.
Download fail Downloading of the firmware has failed.
Preparations
Operations
Information
Preparations