Owner`s manual

ENGLISH
:;t
o
c:
C"
~
tJ>
:::r
o
o
=.
::J
\Q
@ Load the four batteries
properly
as indicated by
the marks in the battery
compartment.
CD Lift the clasp and remove
the rear lid.
® Put the rear cover back on.
1
Inserting the batteries
em.
• Use a LR03/AAA battery for the remote control unit.
• If
you try to operate the RC-7000CI / 7001 RCI near the
device you want to operate but the device does not operate.
replace the batteries with
new ones. (The included batteries
are only meant for verifying operation Replace them with
new batteries soon.)
• When inserting the batteries.
be sure to do so in the proper
direction. following the
"®" and "e" marks in the battery
compartment.
•
To prevent damage or leakage of battery fluid:
• Do not use a
new battery together with an old one.
• Do not use
two different types of batteries.
• Do not attempt to charge dry batteries.
• Do not short-circuit. disassemble. heat or dispose of
batteries
in flames.
• If the battery fluid should leak. carefully wipe the fluid off the
inside of the battery compartment
and insert new batteries.
• Remove the batteries from the remote control unit if it will
not
be in use for long periods.
• When replacing the batteries. have the new batteries ready
and insert them as quickly as possible.
•
"LOW BATIERY"appears on the LCD when the remaining
battery power decreases. When this happens. replace the
battery
as soon as possible.
RC·7000CI Editor function 26
RC-7000CI Editor installation· · · 26
Using RC-7000CI Editor · 26
Deleting signals registered with the learning function··
·18
Deleting signals registered with the macro function 19
Deleting favorites · 19
Deleting the registered punch-thru function · · .. · 19
Operational reset···· .. · .. ····· .. ··· .. ······· .. ·· .. ·········· ·· .. ··· .. ·· 20
User reset········ .. · .. ·· .. ···· .. ·· .. · .. ·· .. ····· .. ······ .. ···· .. ·· .. ·· · .. ·· 20
Lock function 21
Unlock function· .. ·········· .. ··· .. · .. ········· .. ········ .. ······· .. ······ .. ·21
Accessories
I Troubleshooting 27 1
Check that the following parts are supplied with the product.
INetwork function 221
Operations using nodes
Adding nodes (1 ) 23
Adding nodes (2) 23
Deleting nodes 24
Viewing nodes
.. · · · · .. · · .. · 24
Changing node labels 25
Setting the receiver display mode (ROM) · 25
Checking the remote control unit version · 25
CD Owner's Manual 1
@ Remote control 1
® LR03/AAA batteries 4
®CD-ROM 1
® USB cable (Cord length: Approx. 3.3 ft /1 m) 1
I PC Application
ISpecifications 27I
Contents
Getting Started
Accessories , 1
Inserting the batteries 1
Operating range of the remote control unit · 2
Part names and functions 2
Introduction··· .... ·· .... ····· ····· .. ·· .. · ···.·· · · .. · ·· .. ··3
Settings menu map 4
Operation the LCD button 5
Settings
Setting the screen display time 5
Setting the backlight
on time · 6
Adjusting the contrast 6
Completing the setting 6
Various settings
Using the preset memory function · 7
Using the learning function
7. 8
Using the Macro function
8, 9
Using the delay time function 9
Using the code search function · 9
Favorites settings ·10.
11
Using the punch through function ·· 11
Editing pages 11. 12
Editing devices · ·12 - 15
Editing buttons 15 - 18
Thank you for purchasing this DENON product. To ensure
proper operation. please
read these owner's manual carefully
before using the product.
After reading them.
be sure to keep them for future
reference.
IGetting Started
IOperation