Owner`s manual
~
button:
\l
button:
ZONE
6button :
ZONE
5button :
® Use the following buttons to input the address and press the
SELECT/ENTER
knob.
* Button functions when entering address
SELECTJENTER
knob: Turn Select
Press
··
Confirm
Cursor to right
Cursor
to
left
Setting during address entry
Cancel entry
df~:
Set the
IP
address within the ranges shown below. The Network
function cannot
be
used if other
IP
addresses are set.
CLASS
A:
10.0.0.0 - 10.255.255.255
CLASS
B:
172.16.0.0 - 172.31.255.255
CLASS
C:
192.168.0.0 - 192.168.255.255
i~.~~:
When connecting
an
xDSL modem or terminal adapter directly
to
the
POA·3012CI,
input the subnet mask indicated
in
the
documentation supplied by. your provider. Normally input
255.255.255.0.
!,~.~~~,;.
When connected to a gateway (router), input its
IP
address.
t~~PN$,.~~DNS
If
there
is
only one DNS address indicated in the documentation
supplied by your provider, input it at "Primary DNS".
If
there are
two
or more
DNS
addresses, input the first one at "Secondary
DNS".
® Press the
SELECT/ENTER
knob.
Setup is complete.
*When connecting to the network
via
a Proxy server, select
"Proxy" and press the
SELECT/ENTER
knob (Gr"page
16
"Proxy
settings").
.....
4f
..
'-.L;,-
L·'
!"",!,=.
Sec
0
no::!
.::t~-."/
r
~
Select ·DHCP
W
•
,I
:
;1{:'~lt
______
'--_
-_
~_.-:.:-:-
·:~~
..
::I'=@=2
=Se=t=·Q=F=F
M
=.
'1-
IP
Addre~~
1
[Ti;~:r.;~:~:::~~:::}:}.
d
..
••••
..
•••••
..
:
I
..
_~J~
S'!·!.f;.
!_1'L~~t:_
---
-
-.
I :
, I
.-::.
C'
t:'
.-::,0=1:"
.')
t::'
0=
.:"~:-.&
•••••
'
••
It
lit
'"
.'
i1*'
'.
'~'.l_'_~'.l_''''''''''-'''''''
'-'_~.
•
·
..
•
........,
"------;:================-~
.
•
P
t;'_!-'j§.!-~':~
_
I~i2
..
:
~£1.
...
~J
[1
fL~
••••
4)._
'-;::====::=:=:===========~
:
·
·
Use
this procedure to configure the Wired
LAN
settings.
Wired LAN settings
I® Input the
add
res;.
CD
Select"
DHCP"
and
press the
SELECTJENTER
knob.
@
Turn
the
SELECT/ENTER
knob to set "DHCP" to "OFF", then
press the
SELECTJENTERknob.
The
DHCP
function
is
disabled.
1Connect the LAN cable
(t::V'
page 8).
2
Tum
on the POA-3012CI (t::V'page 17).
POA-3012CI
performs automatic network setup due
to
the
DHCP
function
..
When connecting
to
a network that
has
no
DHCP
function,
perform the setting
in
step
3.
3
Set the IP address at the menu "Network Setup" -
"Network Setup".
I
'
·~fittwork
'§~p
..
,
.•.
i
Mak~settingsfor'~!f~:LAN.
Network Setup
o Networklnfonnation
Network Setup
It:,
..
to::
•
Menu
tree
•
• If
you
are
using a broadband router
(DHCP
function). there is no need
to make the settings at "Setting the
IP
Address"
and
"Setting the
Proxy", since the
DHCP
function
is
set to
"ON"
in
the POA-3012CI's
default settings.
• If the
POA-3012CI
is
being used connected to a network without the
DHCP
function, the network settings must
be
made.
In
this case,
some knowledge of networks
is
required.
For
details, consult a
network administrator.
• If
you
cannot connect
to
the Internet, recheck the connections
and
settings (Gr"page
8)
• If
you
do
not understand about Internet connection, contact your
ISP
(Internet Service Provider) or the store from which you purchased
your computer.
aNetwork,Infonnation
DisplaY
~etwork
.Information.'
,,'
Network Setup
Make network settings.
Main Setup
• DHCP (Dynamic Host Configuration Protocol) :
These are systems by which the
IP
address
and
other network
settings are automatically set for the
POA-3012CI,
computer,
broadband router
and
network devices.
• DNS (Domain
Name
System) :
This
is
a system for converting the domain names used when
browsing Internet sites (for example,
..
www.denon.jp
..
) into the
IP
addresses actually used for communications (for example,
"202.221.192.106").
[Items
to
be checked]
h.PttCP.
ON
or
Off
..
.
.,
Address
:'~<<>:i,
,'''''''''''~;:'':
-!h:,;;-_"~':~':'U':;,};_
Wj(L~~;~
,tfA~6!!!tel
ENGLISH
•
15