Graphical User Interface Use this manual in combination with the operating guide displayed on the GUI screen. GUI Menu Operation (vpage 15) GUI Menu Map (vpage 16) Language (vpage 21) VIDEO PROCESSOR DVP-602CI Owner’s Manual DVP602CI_ENG_6th.
SAFETY INSTRUCTIONS n SAFETY PRECAUTIONS 1. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
FCC INFORMATION (For US customers) n NOTE ON USE / HINWEISE ZUM GEBRAUCH 1. COMPLIANCE INFORMATION Product Name: VIDEO PROCESSOR Model Number: DVP-602CI This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation.
Getting Started Connections Contents Setup Playback Getting Started Accessories······················································································2 Cautions on Handling······································································2 Cautions on Installation··································································2 About the Remote Control Unit·····················································3 Inserting the Batteries···················································
• Before turning the ON/STANDBY switch on Check once again that all connections are correct and that there are no problems with the connection cables. Getting Started Thank you for purchasing this DENON product. To ensure proper operation, please read these owner’s manual carefully before using the product. After reading them, be sure to keep them for future reference. (For North America model) b Wall • Cautions on using mobile phones Using a mobile phone near this unit may result in noise.
Getting Started Connections About the Remote Control Unit Inserting the Batteries q Lift the clasp and remove the rear lid. Operating Range of the Remote Control Unit Point the remote control unit at the remote sensor when operating it. w Load the two batteries properly as indicated by the marks in the battery compartment. R03/AAA Setup Playback 30° 30° Information e Put the rear cover back on. Approx.
Getting Started Connections Part Names and Functions For buttons not explained here, see the page indicated in parentheses ( ).
Getting Started Connections Rear Panel Q1 Q0 o i u Setup Playback Information Troubleshooting q Specifications q TRIGGER OUT jack····································································(14) w REMOTE CONTROL jacks·························································(14) e RS-232C connector····································································(14) r S-VIDEO connector···································································(12) w e r t t VIDEO connector····
Q1 q Q2 w Q4 u i Q5 Q6 Q7 o Q0 NOTE Specifications y (PROGRESSIVE)··········································· (22) Q4 Source select buttons (SOURCE)········· (19, 21) Q5 ASPECT button············································ (22) Q6 STATUS button··········································· (24) Q7 ENTER button·············································· (15) Q8 RETURN button··········································· (15) Troubleshooting Q3 Information t Playback r q Transmission indic
Getting Started Connections Preparations Connections Setup Connections for all compatible audio and video signal formats are described in this owner’s manual. Please select the types of connections suited for the equipment you are connecting. With some types of connections, certain settings must be made on the DVP-602CI. For details, refer to the instructions for the respective connection items below. Cables Used for Connections Select the cables according to the equipment being connected.
Getting Started Connections Video Conversion Function • This function automatically converts various formats of video signals input to the DVP-602CI into the format used to output the video signals from the DVP-602CI to a monitor.
Getting Started Connections Connecting Equipment with HDMI connectors n Connecting a TV to the DVP-602CI via an AV amplifier Player With HDMI connections, the video and audio signals can be transferred with a single cable. )%.* 065 AV amplifier )%.* */ )%.* 065 Connecting an HDMI-compatible player n Connecting a TV directly to the DVP-602CI Setup Player Playback )%.
n Connecting a TV directly to the DVP-602CI Player TV "6%*0 015*$"065 %7* % 065 n Connecting a TV to the DVP-602CI via an AV amplifier TV Player "6%*0 015*$"065 n Connecting to a TV without passing through the AV amplifier TV Player "6%*0 %7* % 065 )%.* */ 015*$"065 %7* % 065 )%.* */ )%.* */ AV amplifier AV amplifier )%.* 065 Setup "6%*0 )%.
Getting Started Connections n Connecting a TV to the DVP-602CI via an AV amplifier Connecting Equipment with COMPONENT connectors TV Player Carefully check the inputs and outputs, and be sure to interconnect correctly. "6%*0 7*%&0 015*$"065 $0.10/&/5 7*%&0 065 13 1# : n Connecting to a TV without passing through the AV amplifier TV Player )%.* */ "6%*0 7*%&0 015*$"065 $0.10/&/5 7*%&0 065 13 1# : )%.
Carefully check the inputs and outputs, and be sure to interconnect correctly. n Connecting a TV to the DVP-602CI via an AV amplifier TV Player "6%*0 015*$"065 7*%&0 065 TV Player "6%*0 7*%&0 4 7*%&0 065 n Connecting to a TV without passing through the AV amplifier )%.* */ 015*$"065 7*%&0 4 7*%&0 065 7*%&0 065 )%.* */ n Connecting a TV directly to the DVP-602CI Player "6%*0 4 7*%&0 065 AV amplifier 7*%&0 065 )%.* */ AV amplifier "6%*0 or )%.* */ )%.
Getting Started Connections Required system Connections to Other Devices Carefully check the inputs and outputs, and be sure to interconnect correctly. For firmware update and web control. Setup Computer Playback Modem Information To WAN side Troubleshooting Router n Modem • A contract with an ISP is required to connect to the Internet. No additional contract is needed if you already have a broadband connection to the Internet. • The types of routers that can be used depend on the ISP.
Getting Started Connections Connecting the Power Cord External Controller Wait until all connections have been completed before connecting the power cord. RS-232C connector To household power outlet Power cord (included) This connector is used for an external controller. b If you wish to control the DVP-602CI from an external controller using the RS-232C connector, perform the operation below beforehand. q Turn on the DVP-602CI’s power. w Turn off the DVP-602CI’s power from the external controller.
Getting Started Connections Examples of GUI Screen Displays GUI Menu Operations With the DVP-602CI, settings and operations for most functions can be performed by operating while looking at the GUI menus displayed on the monitor screen. Some typical examples are described below. Example: Browse Menu (Top Menu) The same operation is possible on the main unit or remote control unit. Setup Playback When an x.v.Color signal or a 1080p component video signal and computer resolution (ex.
Getting Started Connections GUI Menu Map INFORMATION (vpage 24) n Status n HDMI Information Setup SOURCE SELECT (vpage 21, 22) Playback n HDMI 1 ~ 6, COMP.
Getting Started Connections Setup s RGB Range g Monitor Out Make settings for RGB output range. Make settings for HDMI monitor output. [Selectable items] Normal Enhanced Make detail settings for various parameters. Setup Make settings for HDMI video/audio output. Playback HDMI Setup F Menu tree F • When “YCbCr” is selected under “Color Space”, “RGB Range” will have no effect. • The computer resolution output will be “Enhanced” irrespective of this setting. The image is displayed in full-screen.
Make network settings. F Menu tree F Setup Network Setup a Network Setup s Power Saving Use this procedure to configure the Wired LAN settings. 1 2 Connect the LAN cable (vpage 13). 3 Set the IP address at the GUI menu “Setup” – “Network Setup” – “Network Setup”. Turn on the DVP-602CI (vpage 24). DVP-602CI performs automatic network setup due to the DHCP function. When connecting to a network that has no DHCP function, perform the setting in Operation 3.
Getting Started Connections n Proxy settings Make this setting when connecting to the Internet via a proxy server. t Use the ui p button to input the proxy server address or domain name and press the ENTER button. When “Address” is selected in Operation r : Input the address When “Name” is selected in Operation r : Input the domain name y Use the uio p button to input the proxy server port number and press the ENTER button. u Use the i button to select “Exit” and press the ENTER button.
Change the GUI background. [Selectable items] Picture Black Gray Blue Format d Trigger Out h Maintenance Mode Select the conditions to turn on the trigger out with respect to the input source, HDMI monitor, etc. For details about the trigger out function, see page 14. This sets the function for maintenance by a DENON serviceperson or installer. (For professional use only.) ON [Selectable items] ––– NOTE Select the video output signal format to match the monitor.
Getting Started Connections k Add New Feature Display the new functions (payment required) which can be purchased for downloading to the DVP-602CI and upgrade. When you purchase a new function and register your user information, “Registered” is displayed on this menu and you can proceed with the upgrade. Upgrade Language Source Select F Menu tree F Setup Use this procedure to select the input source and make the settings related to playing input sources.
• This can be set when “i/p Scaler” is set to “ON”. • To enjoy 1080p/24 Hz video images, use a monitor which supports 1080p/24 Hz video signals. • With film source (24 Hz), you can enjoy a film-like image. It is recommended that you use 1080p/60 Hz for video source and mixed source. • It is not possible to convert a 50 Hz signal to 1080p/24 Hz. It is output at a resolution of 1080p/50 Hz. • It is not possible to convert a 1080p/60 Hz signal to 1080p/24 Hz. F Menu tree F Source Select HDMI 1 ~ 6, COMP.
Getting Started Connections f Hue Picture Adjust Adjust color hue. Adjust the picture quality. Parameter [Variable range] F Menu tree F ~ –6 0 ~ +6 Parameter Picture Adjust Audio Setup Adjust various audio parameters. Playback F Menu tree F a Contrast g DNR s Brightness Reduce overall picture noise. d Chroma Level g DNR Parameter Information Compensate for mismatched timing between video and audio. Troubleshooting This sets the delay time for audio signals.
Getting Started Connections Playback Information Preparations Status Shows information about current settings. Setup Turning the Power On Press the or [POWER ON] button.
Getting Started Connections Operating the DVP-602CI Using a Browser (Web control) This function lets you operate the DVP-602CI using Internet Explorer. Setup Playback [ALL OFF] 1 Switch “OFF” the “Power Saving” setting under “Setup” – “Network Setup” on the GUI menu (vpage 19). 2 Check the DVP-602CI’s IP address with “Setup” – “Network Setup” – “Network Information” on the GUI menu (vpage 19).
After entering characters, click “Set” to set, or click “Def” to return to initial setting Other Operations and Functions Personal Memory Plus Function Click “SAVE” when you want to save settings, and click “LOAD” when you want to call settings Last Function Memory This stores the settings as they were directly before the standby mode was set. When the power is turned back on, the settings are restored to as they were directly before the standby mode was set.
Getting Started Connections Resolution input/output conversion table Other Information MONITOR OUT Resolution Setup Input Formats HDMI (High-Definition Multimedia Interface) Setup Playback Information HDMI is a digital interface standard for next generation TVs based on DVI (Digital Visual Interface) standards and optimized for use in consumer equipment. Non-compressed digital video and multi-channel audio signals are transmitted with a single connection.
Symptom Troubleshooting Cause Countermeasure Page Display is off. • The “Dimmer” setting is set to • Set to something other than “OFF”. “OFF”. 20 Power turns off suddenly and power indicator flashes red. • Set is damaged. • Turn off the power and contact a DENON service center. – Set does not work • Batteries are worn. properly when • You are operating outside of the remote control specified range. unit operated. • Obstacle between main unit and remote control unit.
Getting Started Connections Specifications n General Setup Power supply: Power consumption: Maximum external dimensions: Weight: North America model : AC 120 V, 60 Hz European model : AC 230 V, 50 Hz North America model : 90 W European model : 90 W 0.3 W (Standby) 434 (W) x 107 (H) x 280 (D) mm (17-3/32” x 4-7/32” x 11-1/32) 4.
www.denon.com Denon Brand Company, D&M Holdings Inc. Printed in Japan 00D 511 4750 005 DVP602CI_ENG_6th.
