Ver. 1 SERVICE MANUAL MODEL JP E3 DVM-1845/745 E2 EK E2A E1C E1K EUT 3 DVD VIDEO AUTO CHANGER 注 意 サービスをおこなう前に、このサービスマニュアルを 必ずお読みください。本機は、火災、感電、けがなど に対する安全性を確保するために、さまざまな配慮を おこなっており、また法的には「電気用品安全法」に もとづき、所定の許可を得て製造されております。 従ってサービスをおこなう際は、これらの安全性が維 持されるよう、このサービスマニュアルに記載されて いる注意事項を必ずお守りください。 ● For purposes of improvement, specifications and design are subject to change without notice. ● Please use this service manual with referring to the operating instructions without fail.
DVM-1845/745 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
DVM-1845/745 SPECIFICATIONS Item 1. Video Output Conditions 75 load 2. Optical Digital Out Unit Nominal Limit Vpp 1.0 ± 0.1 dBm -18 Vrms 2.0 dB 120 3. Audio (PCM) 3-1. Output Level 1 kHz, 0 dB 3-2. S/N 3-3. Freq. Response DVD fs = 48 kHz, 20 Hz ~ 22 kHz dB ± 1.0 CD fs = 44.1 kHz, 20 Hz ~ 20 kHz dB ± 1.0 DVD 1 kHz, 0 dB % 0.004 CD 1 kHz, 0 dB % 0.004 3-4. THD+N Notes: 1. All Items are measured without pre-emphasis unless otherwise specified. 2.
DVM-1845/745 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts, and wires have been returned to their original positions. Afterwards, do the following tests and confirm the specified values to verify compliance with safety standards. 1.
DVM-1845/745 STANDARD NOTES FOR SERVICING Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is indicated as shown. When soldering, be sure to use the Pb free solder. How to Remove / Install Flat Pack-IC Top View Out Bottom View In 1. Removal Input With Hot-Air Flat Pack-IC Desoldering Machine: 1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1) 2.
DVM-1845/745 With Soldering Iron: 3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it. CBA 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig.
DVM-1845/745 With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3) 1. Using desoldering braid, remove the solder from the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily. 2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5. 2.
DVM-1845/745 Instructions for Handling Semiconductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body. 2.
DVM-1845/745 CABINET DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart ID/ LOC. No. This flowchart indicates the disassembly steps to gain access to item(s) to be serviced. When reassembling, follow the steps in reverse order. Bend, route, and dress the cables as they were originally.
DVM-1845/745 Reference Notes (L-1) CAUTION 1: Locking Tabs (L-1) are fragile. Be careful not to break them. (B) 1-1. To release eight Locking Tabs (L-1), first release five Locking Tabs (A), and then three Locking Tabs (B). (Fig. D2) (L-1) CAUTION 2: Electrostatic breakdown of the laser diode in the optical system block may occur as a potential difference caused by electrostatic charge accumulated on cloth, human body etc., during unpacking or repair work.
DVM-1845/745 Screw A [5] Slide Tray Assembly Chuck arm Rotary tray washer Rotary tray spring Rotary tray washer A CN2103 (S-4) Turn B [7] Power Switch CBA (L-2) CN2201 Slide Tray Assembly Short the three short lands by soldering. (Either of two places.) (L-2) Slide Tray [6] Function CBA Gear (B) Fig. D4 FPC Cable View for A Relay CBA CN5001 CN5004 FFC cable from the DVD Main CBA Unit FFC cable from the Changer CBA View for B (Relay CBA) Fig.
DVM-1845/745 [12] Slide Tray Gear (B) (S-5) (S-6) [8] Rear Panel (S-11) [13] Slide Tray Gear (A) (P-1) (S-5) (S-10) (S-6) (S-5) (S-6) [15] Switch CBA Belt L [11] Loading Pulley (S-12) (S-7) (S-5) [16] Tray Guide (R) (L-4) [14] Motor Assembly Fig. D6 Fig. D8 [9] Tray Guide (L) (S-14) (S-14) (S-8) [18] AV CBA (S-9) (S-13) CN3102 CN3301 CN1601 CN1001 (S-13) [17] Changer CBA CN3003 CN3004 [10] Tray Guide (R) Unit Fig. D7 Fig.
DVM-1845/745 (S-15) [19] DVD Main CBA Unit [20] PCB Holder Fig.
DVM-1845/745 SLIDE TRAY ASSEMBLY DISASSEMBLY INSTRUCTIONS 1. Disassembly Flowchart This flowchart indicates the disassembly steps to gain access to item(s) to be serviced. When Reassembly, follow the steps in reverse order. Bend, route, and dress the cables as they were originally.
DVM-1845/745 Reference Notes 2. Disassembly Method 1. Disassembly note Slide the Rotary Tray slowly in the direction of the front while rotating it. 2. Reassembly note Align the rails on the Rotary Tray with the slot on the sensor and align pin A with hole A on the Rotary Tray. 3. Reassembly note Re-solder the leads on the Rotary Motor Assembly or the Detector Switch as shown in Fig. MD4. 4.
DVM-1845/745 (S-1) Slide Tray [1] Chuck Arm (P-1) (W-1) (W-1) Clamper Yoke Magnet [9] Detector Switch Desolder Fig. MD1 Hole A [8] Mecha Cable Desolder Lead clamper [10] Rotary Motor Assembly [7] Gear Plate (S-8) [6] Belt L (S-6) (S-7) (S-6) 1 (S-5) [5] Plate Spring (L-1) (L-1) 2 (S-6) CN5002 Rails on the Rotary Tray [2] Rotary Tray Slot on the sensor CN5101 [8] Mecha Cable (L-1) Bottom View of the Slide Tray Pin A Fig.
DVM-1845/745 CN5005 [13] Rotary Stopper Slide Tray CN5003 [15] Motion Gear Slot A Pin B Pin D (P-2) turn [12] Slot Lever Slot B (S-9) (S-9) Slot C Pin C Pin E [14] Mecha Holder Assembly Pin E [11] Relay CBA + Sensor CBA Bottom View of the Slide Tray Pin D A Slot A Pin C Slide Tray Bottom View of the Mecha Holder Assembly Short the three short lands by soldering. (Either of two places.) Hole B Cavity A Rib A FPC Cable View for A Fig.
DVM-1845/745 [21] Slide Tray Chassis [20] Idler Arm [19] Idler Pad [17] Rotary Tray Gear [18] Idler Gear (P-3) [16] Loading Pulley (W-3) (W-2) (W-4) (S-10) (S-11) Fig.
DVM-1845/745 TROUBLESHOOTING FLOW CHART NO.1 The power cannot be turned on. Is the fuse normal? Yes Is normal state restored when once unplugged power cord is plugged again after several seconds? Yes Is the CHG +3.3V line voltage normal? Yes Is each voltage of the secondary side normal? Yes When pressing POWER button (SW2101), is the voltage of 0V supplied to pin(42) of IC3001? Yes Is the voltage of 3.3V supplied to pin(1) of IC3001? Yes Replace IC3001. No See FLOW CHART No.2
DVM-1845/745 FLOW CHART NO.6 P-ON+10V (EV+10V) is not outputted. Is 10V voltage supplied to the emitter of Q1002? No Check D1030, C1035, C1048, L1009 and the periphery circuit, and service it if defective. Yes No Is the voltage of base on Q1002 lower than the voltage of emitter on Q1002 when turning the power on? Check Q1016 and service it if defective. Yes Replace Q1002. FLOW CHART NO.7 P-ON+5V is not outputted. (P-ON+10V is outputted normally.
DVM-1845/745 FLOW CHART NO.12 The fluorescent display tube does not light up. No Is 3.3V voltage supplied to Pin(13) and Pin(43) of IC2001? Yes Is the voltage of approximately -19V supplied to Pin(30) of IC2001? Yes Replace the fluorescent display tube or IC2001. Check the P-ON+3.3V line and service it if defective. No Check the -FL line and service it if defective. FLOW CHART NO.13 The key operation is not functioning.
DVM-1845/745 FLOW CHART NO.14 No operation is possible from the remote control unit. Operation is possible from the DVD, but no operation is possible from the remote control unit.
DVM-1845/745 FLOW CHART NO.18 [No Disc] indicated. (When the focus servo is not functioning.) Replace the DVD Main CBA Unit. No improvement can be found. Yes No Original DVD Main CBA Unit is poor. Replace the DVD Mechanism. FLOW CHART NO.19 [No Disc] indicated. (When the laser beam does not light up.) Replace the DVD Main CBA Unit. No improvement can be found. Yes No Original DVD Main CBA Unit is poor. Replace the DVD Mechanism. FLOW CHART NO.
DVM-1845/745 FLOW CHART NO.21 Picture does not appear normally. Set the disc on the disc tray, and playback. Are the video signals outputted to each pin of CN1601 on the AV CBA? CN1601 CN1601 CN1601 CN1601 CN1601 1PIN 3PIN 5PIN 7PIN 9PIN No S-Y(I) Pr/Cr Pb/Cb S-Y(I/P) S-C Yes Are the video signals shown above inputted into each pin of IC1402 and IC1403? IC1402 IC1402 IC1402 IC1403 IC1403 3PIN 6PIN 8PIN 1PIN 3PIN Replace the DVD Main CBA Unit or DVD Mechanism.
DVM-1845/745 FLOW CHART NO.22 Audio is not outputted. Set the disc on the disc tray, and playback. Are the analog audio signals outputted to each pin of CN1601 on AV CBA? No Replace the DVD Main CBA Unit or DVD Mechanism. CN1601 11PIN AUDIO(L) CN1601 13PIN AUDIO(R) Yes Are the analog audio signals inputted to each pin of IC1201. Check each line between each pin of CN1601 and each pin of IC1201 on AV CBA, and service it if defective.
DVM-1845/745 FLOW CHART NO.23 Rotary tray does not function. Is the normal control voltage inputted to pins (40, 41) of IC3001? For each terminal voltage, refer to FLOW CHART No.13 No Check the switches (SW2208, 2209, 2211 - 2214) and their periphery, and service it if defective. Yes No Is the voltage of 3.3V supplied to pin(1) of IC3001? Yes Is the normal control voltage outputted to pins (22, 23) of IC3001? Yes Check CHG 3.3V line and service it if detective.
M M SPINDLE MOTOR SLED MOTOR AUDIO-MUTE ADAC-MD ADAC-MC ADAC-ML FS TRAY-IN MECHA CBA TS PICK-UP UNIT TO AUDIO BLOCK DIAGRAM CN5003 1 2 4 5 6 CN5005 2 3 1 4 CN5001 12 9 13 14 11 CN5004 2 3 1 4 RELAY CBA CN3001 12 9 13 14 11 CN3301 15 14 12 11 10 SP(+) SP(-) SL(-) SL(+) TRAY-IN CN301 15 14 12 11 10 DVD MAIN CBA UNIT CHANGER CBA FS(+) FS(-) TS(+) TS(-) CN201 2 3 1 4 1 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT. 1 +3.
RM2 RM1 M TO SYSTEM CONTROL-1 BLOCK DIAGRAM CN401 CN1001 1 REMOTE1 SENSOR CBA UP/DOWN SW CN5002 9 8 CN3003 1 2 CHK-ON CHK-OFF GND 7 CN3001 7 5 28 AMP IC3510 (AMP) 1 TO POWER SUPPLY BLOCK DIAGRAM AV CBA TO SYSTEM CONTROL-1 BLOCK DIAGRAM CN301 5 6 7 4 CN5001 1 CHK-ON 3 CHK-OFF 4 2 4 2 JK3501 POWCON PWCHK PWSW CN3301 FP-STB FP-DIN FP-DOUT FP-CLK CN3001 1 3 CN5001 CN3001 8 D-SENS-A 8 6 RT-SENS-A 6 CN5001 7 RM2 5 RM1 RELAY CBA +3.
PICK-UP UNIT DETECTOR CD-LD DVD-LD PD-MONI GND(DVD-PD) GND(CD-PD) GND(LD) C D A B CD/DVD C D A B CD/DVD 2 13 42 53 CN201 16 18 17 15 19 SDRAM DATA(0-15) RELAY CBA CN5005 CN5004 Q253,Q254 CN201 10 CD-LD 10 AMP 10 8 DVD-LD 8 AMP 8 Q251,Q252 7 PD-MONI 7 7 6 GND(DVD-PD) 6 6 5 GND(CD-PD) 5 5 9 GND(LD) 9 9 CN5005 CN5004 16 16 18 18 17 17 15 15 19 19 ~ ~ ~ ~ 159 DATA RAM INST.
TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM YC(0-7) SPDIF PCM-DATA0 PCM-SCLK PCM-LRCK PCM-BCK I2C-SCL I2C-SDA CN1601 1 9 7 5 3 2dB AMP 2dB AMP 2dB AMP 10 11 13 7 DDC I/F 86 90 DVD MAIN CBA UNIT 12 10 83 VIDEO I/F 10 12 81 6 18 7 1 16 TMDS CLOCK- TMDS CLOCK+ TMDS DATA0+ TMDS DATA0- TMDS DATA1+ TMDS DATA1- TMDS DATA2+ TMDS DATA2- SDA CNF01 HDMI-CONNECTOR HOT PLUG 19 DETECT 15 SCL VIDEO-Pr/Cr OUT VIDEO-Pb/Cb OUT VIDEO-Y OUT 24 5 JK
TO SYSTEM CONTROL-1 BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM TO SYSTEM CONTROL-1 BLOCK DIAGRAM TO DIGITAL SIGNAL PROCESS BLOCK DIAGRAM AUDIO-MUTE PCM-SCLK ADAC-MD ADAC-MC ADAC-ML PCM-BCK PCM-DATA0 PCM-LRCK SPDIF 4 3 2 7 6 8 SERIAL CONTROL PORT AUDIO SERIAL PORT 5 SYSTEM CLOCK MANAGER ZERO DETECT ENHANCED MULTI-LEVEL DELTA-SIGMA MODULATOR DVD MAIN CBA UNIT 4X/8X OVERSAMPLING DIGITAL FILTER /FUNCTION CONTROLLER IC601 (AUDIO DAC) DAC DAC LPF+AMP LPF+AMP R-CH L-CH 16 1
AC1001 AC CORD V LINE FILTER L1001 32 LATCH Q1008 F1001 1A/250V A F AV CBA SWITCHING SWITCHING CONTROL HOT Q1031 Q1003 BRIDGE RECTIFIER D1001, D1002 D1004, D1005 HOT CIRCUIT. BE CAREFUL. CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply.
DVM-1845/745 SCHEMATIC DIAGRAMS / CBA’S AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
DVM-1845/745 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: F A V FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQES D'INCELE N'UTILISER QUE DES FUSIBLE DE MÊME TYPE. RISK OF FIRE-REPLACE FUSE AS MARKED. This symbol means fast operating fuse. Ce symbole represente un fusible a fusion rapide. 2.
DVM-1845/745 DVD Main 1/4 Schematic Diagram 1 NOTE: Either IC461 or IC462 is used for DVD MAIN CBA UNIT.
DVM-1845/745 DVD Main 2/4 Schematic Diagram 36
DVM-1845/745 DVD Main 3/4 Schematic Diagram 37
DVM-1845/745 DVD Main 4/4 Schematic Diagram 38
DVM-1845/745 AV 1/2 Schematic Diagram CAUTION ! Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail. F A V CAUTION ! For continued protection against fire hazard, replace only with the same type fuse.
DVM-1845/745 AV 2/2 Schematic Diagram 40
DVM-1845/745 Changer 1/2 , Function , Power Switch & Switch Schematic Diagram 41
DVM-1845/745 Changer 2/2 Schematic Diagram FL2001 MATRIX CHART 7G TL./GR. TR. /CP. 6G 5G 4G PSCAN DVD A 3G 2G 1G RPT ALL CD SACD A B a h h c h h f d g b e 7G 6G 5G 4G 3G 2G 1G a a a a a a a a b b b b b b b b c c c c c c c c d d d d d d d d e e e e e e e e f f f f f f f f g g g g g g g g h TL./GR. TR./CP. i 42 DVD h RPT.
DVM-1845/745 Relay , Sensor , Mecha & Pick Up Unit Schematic Diagram 43
DVM-1845/745 WAVEFORMS WF1 Pin 7 of CN1601 VIDEO-Y WF2 0.2V 0.2V Pin 13 of CN1601 AUDIO(R) 20µs Pin 9 of CN1601 VIDEO-C WF3 WF5 WF6 20µs 0.5V 0.5ms Pin 15 of CN1601 SPDIF 1V 0.1µs C1402 PLUS LEAD NOTE: VIDEO-CVBS 0.5V Measuring Disc DVD: DVDT-S01 CD : TCD-784 20µs Input Signal VIDEO: 75% NTSC COLOR BAR AUDIO: 1KHz, 0dB WF4 Pin 11 of CN1601 AUDIO(L) 0.5V 0.
M SLED MOTOR M TS FS MECHA CBA ROTARY MOTOR PICK UP UNIT 7 9 11 2 DETECTOR 3 6 5 4 TRAY-IN M SPINDLE MOTOR SLIDE TRAY ASSEMBLY UP/DOWN SWITCH 1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 TS(+) FS(+) FS(-) TS(-) GND(CD-PD) GND(DVD-PD) PD-MONI DVD-LD GND(LD) CD-LD GND NU VREF NU B C A D CD/DVD P-ON+5V RELAY CBA CN5004 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CN5005 TS(+) FS(+) FS(-) TS(-) GND(CD-PD) GND(DVD-PD) PD-MONI DVD-LD GND(LD) C
DVM-1845/745 FIRMWARE RENEWAL MODE The appearance shown in (*1) of Fig. c is described as follows: 1. Turn the power on and remove the disc on the tray. 2. To put the DVD player into version up mode, press [9], [8], [7], [6], and [SEARCH MODE] buttons on the remote control unit in that order. The tray will open automatically. Fig. a appears on the screen and Fig. b appears on the VFD. No. "*******" differs depending on the models. F/W Version Up Mode Appearance State 1 Reading...
DVM-1845/745 10. Press [CLEAR] button on the remote control unit. Fig. h appears on the screen. "*******" differs depending on the models. MODEL : ******* Version : *.** Region : * EEPROM CLEAR : OK EEPROM CLEAR : CLEAR EXIT: POWER Fig. h When “OK” appears on the screen, the factory default will be set. Then the firmware renewal mode is complete. 11. To exit this mode, press [ON/STANDBY] button.
DVM-1845/745 TRAY LOCK MODE Tray Lock Mode is defeated a tray-open/close to prevent a case of disc theft in demo mode. Enter this mode as the following procedure. 1. Confirm that the TV Monitor is connected. 2. With playback stopped, press [SETUP], [TOP MENU], [3], [AUDIO], [0] and [SETUP] buttons on the remote control unit in that order. "TRAY LOCK ON" will appear at upper right on the screen. 3.
DVM-1845/745 LEAD IDENTIFICATIONS 2SK3498 KTC3205-Y-AT/P KTA1273-Y-AT/P KRA110M-AT/P KRC110M-AT/P KTA1267-Y-AT/P KTC3199-GR-AT/P 2SC1815-GR(TE2 F T) 2SA966-Y(TE6 F M) 2SA1015-Y(TE2 F T) KTA1266-Y-AT/P KTC3203(Y) G D S E C B E C B 42 LD1117V UZ1086L-ADJ PT204-6B-12 M38503G4A-131FP BA6956AN 22 1 21 C 1 2 3 E KIA4558P/P RC4580IP UTC4558 CXA1511M-T4 MM1636XWRE 8 5 PST3229NR 5 1: Vin 2: Vo 3: GND 4 1: R 2: A 3: K 1 33 4 EL817(B,C) LTV-817C-F PS2561A-1(W) 23 34 22 12 44 1 16 9 1
DVM-1845/745 EXPLODED VIEWS Cabinet 1 2L021 2L021 2L021 2L021 A16 1B1 A2 2L021 2L021 Relay CBA 2L031 2B25 C 2B3 AC1001 2L031 2L032 W3004 B 2B6 JK3501 2L011 2L011 JK1401 JK1404 C' W3003 IC1204 E' JK1202 2B1 2L051 F' D' JK1201 2L041 A AV CBA SCOTCH TAPE 2L011 2L103 2L012 2L033 2L012 2L033 2L011 2B1 B' 2B7 DVD Main CBA Unit F 2L012 2L033 E 2L011 SCOTCH TAPE Changer CBA Power Switch CBA 2L041 A21 2B11 D 2L033 A' A17 2L043 2L012 A15 1L017 Switch CBA 1B33 1L016 1B31 1B
DVM-1845/745 Cabinet 2 L1-6 B1-26 B1-41 B1-43 B1-24 B1-42 B1-3 B1-22 B1-24 B1-30 B1-30 B1-2 Mecha Holder Assembly B1-20 B1-6 B1-19 B1-21 SW5001 B1-36 B1-7 B1-37 B1-8 L1-26 B1-52 L1-5 L1-25 B1-4 B1-38 B1-9 B1-5 L1-6 Rotary Motor Assembly W5001 B1-12 B1-13 L1-11 Sensor CBA L1-23 B1-14 L1-7 Relay CBA B1-16 L1-11 Relay CBA + Sensor CBA L1-11 L1-15 L1-11 51 B1-15
DVM-1845/745 PARTS LIST OF EXPLODED VIEW (CABINET1) ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 ＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. ＊ "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 ＊ Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused. Ref. No. nsp Part No.
DVM-1845/745 Ref. No. nsp Part No.
DVM-1845/745 PARTS LIST OF EXPLODED VIEW OF SLIDE MECHANISM UNIT (CABINET2) ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 ＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. ＊ "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 ＊ Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused. Ref. No.
Chief Ingredient of FAG-102R - Hydrocarbon synthetic oil - Lithium soap - Additives NOTE : Apply some grease to the Fill Color position.
DVM-1845/745 NOTE : Apply some grease to the Fill Color position.
DVM-1845/745 Packing X21 X22 X10 X5 X2 S3 S2 X4 S10 X1 S3 S2 S4 A22 A30 S1 A30 57 Unit
DVM-1845/745 PARTS LIST OF PACKING & ACCESSORIES ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 ＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. ＊ "nsp" 印の部品は常時在庫していませんので供給に長時間を要することがあります。場合によっては、供給をお断りする場合があります。 ＊ Part indicated with the mark “nsp” are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused. Ref. No. nsp Part No.
