HOME THEATER SYSTEM DHT-M330DV OPERATING INSTRUCTIONS BEDIENUNGSANLEITUNG MODE D’EMPLOI ISTRUZIONI PER L’USO INSTRUCCIONES DE OPERACION GEBRUIKSAANWIJZING BRUKSANVISNING AVR-M330 DVD-M330 SYS-M330 (SC-AM330) • DVD-M330(DVD PLAYER): (SC-CM330) DSW-M330) (SC-AM330) Please refer to the operating Instructions of the DVD-M330. • DVD-M330 (DVD-PLAYER): Bitte beziehen Sie sich auf die Bedienungsanleitung des DVD-M330. • DVD-M330 (LECTEUR DVD): Veuillez vous référer au mode d’emploi du DVD-M330.
ENGLISH DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANCAIS DEUTSCH ENGLISH NOTE ON USE / HINWEISE ZUM GEBRAUCH /OBSERVATIONS RELATIVES A L’UTILISATION/ NOTE SULL’USO/NOTAS SOBRE EL USO / ALVORENS TE GEBRUIKEN / OBSERVERA • Avoid high temperatures. Allow for sufficient heat dispersion when installed on a rack. • Vermeiden Sie hohe Temperaturen. Beachten Sie, daß eine ausreichend Luftzirkulation gewährleistet wird, wenn das Gerät auf ein Regal gestellt wird.
ENGLISH 2 INTRODUCTION Thank you for choosing the DENON DHT-M330DV HOME THEATER SYSTEM. This remarkable component has been engineered to provide superb surround sound listening with home theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favourite music sources. As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the contents of this manual before proceeding.
ENGLISH 1 BEFORE USING Pay attention to the following before using this unit: • Moving the set To prevent short circuits or damaged wires in the connection cords, always unplug the power cord and disconnect the connection cords between all other audio components when moving the set. • Before turning the power switch on Check once again that all connections are proper and that there are not problems with the connection cords.
ENGLISH WARNING: • When installing the speaker systems on the ceiling or wall, to ensure safety, have specialists do the installation work. • Be sure to fasten the speaker cords to a wall, etc., to prevent people from tripping over them or otherwise pulling on them accidentally, causing the speaker systems to fall. • Be sure to check for safety after installing the speaker systems. Afterwards, perform safety inspections at regular intervals to be sure there is no danger that the speaker systems will fall.
ENGLISH 5 CONNECTIONS • Do not plug in the AC cord until all connections have been completed. • Be sure to connect the left and right channels properly (left with left, right with right). • Insert the plugs securely. Incomplete connections will result in the generation of noise. • Note that binding pin plug cords together with AC cords or placing them near a power transformer will result in generating hum or other noise.
ENGLISH Be sure to turn the amplifier’s power off when connecting the speaker systems. • Use the included cables to connect the input terminals on the back of the speaker systems (see diagram) to the amplifier’s speaker output terminals. Inverting the polarities will result in unnatural sound, with the phase off or no low bass sound. • Connect the side of the included connection cord with the colored label to the “+” (plus) side.
ENGLISH Replacing the speaker connection cords • The speaker connection cords can be replaced, for example when you want to extend the included connection cords. q Press the release button on the side opposite the lock level to detach the cord from the plug. q w w Peel off the sheathing at the tip of the cord you want to replace, and twist firmly so the tip remains tightly wound.
ENGLISH (2) Connecting the DVD Player and TV • Connect the DVD player’s video signals directly to the TV and switch the picture on the TV. • When making connections, also refer to the operating instructions of the other components. Connecting the AUDIO Jack Connecting the DIGITAL Jack • Connect the video disc player’s analog audio output jacks (ANALOG AUDIO OUT) to the DVD IN jacks using pin plug cords.
ENGLISH (3) Connecting the Audio Signals of a Digital Satellite Tuner and VCR • Connect the video signals directly to the TV and switch the picture on the TV. • When making connections, also refer to the operating instructions of the other components. Digital satellite/cable tuner Connection to the optical digital input terminal • Only audio signals are input to the optical digital input terminal.
ENGLISH (4) Connecting the antenna terminals AM LOOP ANTENNA (Supplied) FM INDOOR ANTENNA (Supplied) DIRECTION OF BROADCASTING STATION FM ANTENNA 75 Ω/ohms COAXIAL CABLE FM ANTENNA ADAPTER (Option) GROUND AM OUTDOOR ANTENNA • An PAL-type FM antenna cable plug can be connected directly. • If the FM antenna cable’s plug is not of the PAL-type, connect using the PAL-type antenna adapter (Option). AM loop antenna assembly Connection of AM antennas Connect to the AM antenna terminals.
ENGLISH (5) Using the active subwoofer • Use Subwoofer jack to connect in case you had additional active subwoofer. • You can connect a larger active subwoofer to the system. Connect the active subwoofer to the SW (Subwoofer) PRE-OUT jack using a shielded audio cable. AV SURROUND RECEIVER (AVR-M330) ACTIVE SUBWOOFER (6) Using SURROUND BACK PRE OUT (SBL/SBR) • Use SURR. BACK PRE OUT jack to connect additional POWER AMPLIFIER and speaker systems. You can enjoy 6.1CH or 7.1CH surround system.
ENGLISH (7) Connecting the audio components (DVD-M330) • The AVR-M330 can be used connected in a system with the DVD-M330 DVD player. • For instructions on operating the DVD-M330 DVD player, refer to their respective operating instructions. • Only the DVD-M330 DVD player can be connected directly to the AVR-M330 using system connections. NOTES: • This system includes digital circuitry which may cause interference such as color blotching or changes in the color on TVs.
ENGLISH 6 PART NAMES AND FUNCTIONS AV SURROUND RECEIVER (AVR-M330) Front Panel • For details on the functions of these parts, refer to the pages given in parentheses ( ). !0 !1 q w e r t q Power operation switch (ON/STANDBY)..................................(29) w Remote control sensor.............................................................(19) e Surround mode button (SURROUND MODE)..........................(30) r Super Dynamic Bass/Preset EQ button (SDB/P.EQ) ................
ENGLISH Remote control unit • For details on the functions of these parts, refer to the pages given in parentheses ( ). • Some of the buttons on the remote control unit have some functions. The functions are switched using the remote control mode selector switches. q @4 w @5 @6 @7 @8 @9 #0 #1 e r t y u i o !0 !1 !2 !3 !4 !5 !6 #2 #3 #4 #5 #6 !7 !8 #7 #8 #9 $0 !9 $1 @0 @1 @2 @3 $2 $3 $4 $5 q Transmission indicator w Sleep timer button ............................................................
ENGLISH Names and functions of remote control unit buttons on the DHT-M330DV • Buttons in sections q ~ e can be operated regardless of the position of mode switches 1 and 2. • Consider as standard positions, and switch as necessary to operate. q 3 q 1 e 2 w q 3 q 3 1 Set mode switch 1 to the “DVD” position. 2 Set mode switch 2 to the position of the function you want to operate (DVD, TUNER or AMP.). Downloaded From TheatreSystem-Manual.
ENGLISH 3 Operate the DHT-M330DV. [3] Tuner system buttons (Operated with mode switch 2 set to “TUNER”) [1] Surround amplifier system buttons (Operated with mode switch 2 set to “AMP.”) • These operations are possible with mode switch 1 at any position.
ENGLISH 7 REMOTE CONTROL UNIT • The included remote control unit (RC-996) can be used to operate not only this unit but other remote control compatible DENON components as well. In addition, the memory contains the control signals for other remote control units, so it can be used to operate non-DENON remote control compatible products. (1) Inserting the batteries q Remove the remote control unit’s rear cover. w Set three R6P/AA batteries in the battery compartment in the indicated direction.
ENGLISH • The included remote control unit (RC-996) can be used to operate not only the DHT-M330DV but also and to operate other remote control compatible DENON products. In addition, the remote control operation codes of other major brands of TVs and video decks are also stored in the remote control unit, so the unit can be used to operate these TVs and video decks as well.
ENGLISH (4) TV and video deck preset memories • Components of other brands can be operated with the included remote control unit by storing their codes in the preset memory. Note that depending on the model some operations may not be possible and some buttons may not operate properly.
ENGLISH Combinations of preset codes for different brands TV Admiral 045, 121 Fujitsu Adventura 122 Funai 004, 062 004, 062 Aiko 054 Futuretech 004 Akai 016, 027, 046 GE 020, 036, 037, 040, 044, 058, 066, 088, 119, 120, Alleron 062 A-Mark 007 Goldstar 015, 029, 031, 039, 048, 051, 056, 057, 067, Amtron 061 125, 147 068, 069, 116, 165 Anam 006, 007, 036 Grundy 062 Anam National 061, 147 Hitachi 029, 031, 051, 052, 070, 111, 112, 113, 124, 134 AOC 003, 007, 033, 038, 039, 04
ENGLISH TV National Quenties 002 Sharp NEC 031, 038, 039, 048, 057, 084, 086, 135, 147 Siemens 013 Nikko 054 Signature 045, 144 NTC 054 Simpson 050 Optimus 128 Sony 043, 046, 138, 146, 150 Optonica 011, 012, 093, 121 Soundesign 030, 050, 062 Orion 004, 139 Spectricon 007, 033 Panasonic 002, 009, 017, 036, 037, 071, 141, 143, 147 Squareview 004 Philco 005, 010, 030, 050, 051, 056, 079, 085, 127, 131, Supre-Macy 032, 122 132, 145, 147 Supreme 046 005, 015, 017, 050, 051,
ENGLISH VCR 081 JVC 004, 005, 006, 026, 029, 043, 044, 045, 046, 085 095 Kenwood 004, 005, 006, 026, 029, 033, 045, 085, 090 Aiwa 009 Kodak 088 Akai 026, 027, 070, 072, 082, 083, 084 Lloyd 009, 094 Alba 055 LXI 088 Amstrad 009 Magnavox 015, 016, 042, 049, 063, 106 ASA 042 Magnin 087 Asha 087 Marantz 004, 005, 006, 015, 042, 049, 085, 090 Audio Dynamic 005, 085 Marta 088 088 MEI 049 Beaumark 087 Memorex Broksonic 086, 093 Calix 088 Metz 123, 124, 125, 126, 127, 1
ENGLISH VCR Randex 088 Symphonic 009, 094 RCA 007, 013, 019, 023, 058, 063, 064, 065, 073, 080, Tandy 009 082, 087 Tashiko 009, 088 Realistic 009, 021, 031, 033, 049, 053, 081, 087, 088, 091, Tatung 004, 026, 030 094, 097, 098 Teac 004, 009, 026, 094 Ricoh 055 Technics 024, 049 Salora 033, 041 Teknika 009, 010, 022, 049, 088, 094 Samsung 007, 011, 051, 059, 070, 083, 087, 089, 113 TMK 087, 092 Sanky 081 Toshiba 013, 017, 020, 041, 059, 089, 098, 099, 117 Sansui 005, 026,
ENGLISH (5) Operating the TV/video deck after storing its remote control signals in the preset memory 3-w 3-q 3-q 3 Monitor TV (TV) and video deck (VCR) system buttons q TV system buttons TV POW 0~9 TV IN TV VOL +, – TV CH +, – : : : : : Power on/off Channel numbers TV input switching Volume up/down Channel switching w Video deck system buttons 1 2 3-w 1 Set mode switch 1 to the “DVD” position. 2 Set mode switch 2 to the “TV/VCR” position. 3 Operate the video component.
ENGLISH 8 SETTING UP THE SYSTEM (1) Quick setup procedure • Generally used system settings have already been made on the DHT-M330DV upon shipment from the factory, so the DHT-M330DV can be used as such if there is no need to make changes to the system. • In the cases described below, use the Quick Setup function to make the system settings before using the DHT-M330DV. q When expanding the system configuration to a 6.1- or 7.
ENGLISH (2) Speaker system layout Basic system layout • The following is an example of the basic layout for a system consisting of eight speaker systems and a television monitor: Center speaker system (SC-CM330) Subwoofer (DSW-M330) AV surround amplifier Front speaker systems (SC-AM330) Set these at the sides of the TV or screen with their front surfaces as flush with the front of the screen as possible. Downloaded From TheatreSystem-Manual.
ENGLISH 9 OPERATING THE SURROUND FUNCTIONS Achieving the optimum surround sound • Surround sound can be achieved using the settings made upon shipment from the factory (the default settings), but to achieve even more optimum surround sound, we recommend using the test tones to adjust the levels of the different channels, set the speaker distances (delay time), etc. For details, make the settings referring to page 39.
ENGLISH (2) Input mode setting 1 5 1 3 2 3 5 1 Press the FUNCTION button to select the input function to be played. Main unit Input mode selection function • The input mode can be selected when the input function is set to DVD, TV/AUX1, AUX2. • Different input modes can be selected for each input function. The selected input mode is stored in the memory for the individual input functions.
ENGLISH 4 Start playback on the selected component. • For operating instructions, refer to the component’s manual. 5 Either turn the MASTER VOLUME dial on the main unit or use the VOLUME buttons on the remote control unit to adjust the volume. Input mode display • In the AUTO mode DI G I T AL DVD The volume level is displayed on the display. + Lit • In the DIGITAL PCM mode One of these lights, depending on the input signal.
ENGLISH (3) After starting playback [1] Adjusting the sound quality (SDB/P.EQ) [2] Adjustment the Sound Enhancer The SDB/P.EQ function will not work in the direct mode. The SOUND ENHANCER function will not work in the direct mode. 1 1 1 1 Press the SOUND ENHANCER button. • The tone switches as follows each time the SOUND ENHANCER button is pressed. Remote control unit ENHANCER OFF VOCAL ENH SURR.ENH ENHANCER OFF • The SOUND ENHANCER setting is turned off.
ENGLISH 10 SURROUND PLAYBACK (1) Before playing with the surround function • Adjustments using the test tones can only be performed in the “Auto” mode and are only valid for the AUTO DECODE Surround modes. The adjusted levels are automatically stored in the memory. • Even after adjusting using the test tones, the various channels can be adjusted using the procedure described below to suit the program source and your preferences. 1, 4 2, 4 1, 3 2 3 1 4 3 Press the TEST TONE button. 1 Press the CH.
ENGLISH (2) Playing in the AUTO DECODE mode • In the auto decode mode it is possible to play in the Dolby Digital or DTS Surround mode, depending on the format of the input signal. • It is also possible to play in the Auto Stereo, Dolby Pro-Logic II Cinema/Music/Game or DTS NEO:6 Cinema/Music mode, according to the 2channel mode setting.
ENGLISH [2] 2-channel mode settings • In the AUTO DECODE mode, it is possible to automatically conduct multi-channel playback in the Dolby Digital or DTS surround mode or play in the stereo 2-channel mode (AUTO STEREO mode: factory default setting). For 2-channel input signals, one of four play modes can be set with the 2-channel mode setting (Auto Stereo, Dolby Pro Logic II Cinema, Dolby Pro Logic II Music and Dolby Pro Logic II Game).
ENGLISH Surround parameters (1) (2-channel mode) AUTO-ST (auto stereo) mode 2-channel sources are played in 2-channel stereo. When this mode is selected in the auto decode mode, multi-channel sources (DVD, BS digital, etc.) are played in the multi-channel mode, while 2-channel sources (CDs, etc.) are automatically played in stereo. PLII CINEMA / PLII MUSI / PLII GAME Even 2-channel sources undergo Dolby Pro Logic II processing and are played in the multi-channel mode.
ENGLISH 4 Select and set the surround parameters. (On the remote control unit, use the , cursor buttons to set the parameters.) Surround parameters (2) Main unit If nothing is done for 4 seconds from when the parameter is displayed, the normal display reappears. B Setting the DOLBY VS mode 2SP Ref. Remote control unit 2SP Wide The mode is not displayed if it cannot be selected. Once the surround parameters have been set, stop operating the buttons.
ENGLISH (5) Playback using the Dolby Headphone mode • The AVR-M330 is equipped with the Dolby Headphone mode, a technology developed jointly by Dolby Laboratories and Lake Technology for achieving 3D sound over regular headphones. • The Dolby Headphone mode is set when headphones are connected to the AVR-M330’s headphones jack. • There are actually four Dolby Headphone modes creating different sound field effects: DH1, DH2, DH3 and Bypass (normal stereo playback).
ENGLISH (6) Setting the speaker distance • Input the distances from the listening position to the speakers and set the surround delay time. • The default settings below are set upon shipment from the factory. Preparations: Measure the distances from the listening position to the speakers (L1 to L3 on the diagram at the right).
ENGLISH 2 Table of Surround Mode Parameters (1) Presence/absence of signals and controllability in the various modes DH DVS AUTO DECODE Surround Mode DVS: Dolby Virtual Speaker DH: Dolby Headphone SP/PREOUT PREOUT FRONT L/R SPEAKER CENTER SURROUND L/R SUB-WOOFER SUB-WOOFER DOLBY DIGITAL C C C C E DTS SURROUND C C C C E DOLBY PLII C C C C E AUTO STEREO C E E C E DTS NEO:6 C C C C D DOLBY PLIIx D D D D D DOLBY DIGITAL EX/+PLIIx D D D D D DTS SURR.
ENGLISH 2 Table of Surround Mode Parameters (3) Presence/absence of signals and controllability in the various modes DH DVS AUTO DECODE Surround Mode DVS: Dolby Virtual Speaker DH: Dolby Headphone Surround parameter SDB/P.EQ (Default: DEFEAT all OFF) DH Mode DVS Mode Analog 2-channel DH1/2/3/BYPASS Front ch Ref./Wide 2ch Mode Digital 2-channel SDB ON DRC ON *1 P.
ENGLISH 11 LISTENING TO THE RADIO (1) Tuning 1 Set the remote control selector switches Switch1 to DVD Switch2 to TUNER 2 2 3 1 2, 3 2 Example: Tuning in FM/AM stations 1 Select the FUNCTION “TUNER”. Main unit 2 Remote control unit Select “FM” or “AM”. • The selected “FM AUTO”, “FM MONO” or “AM” is displayed. • When using the remote control, the mode button is used to select FM AUTO and MONO. Main unit 3 NOTE: A humming sound may be heard when using a TV nearby while receiving AM programs.
ENGLISH (2) Presetting stations (remote control unit only) 2 A total of 40 stations (including both FM and AM stations) can be preset. 2 Preset stations using the including remote control unit. Set the remote control selector switches Switch1 to DVD Switch2 to TUNER 3 2, 3 3 Use the“+” and “–” preset buttons to select the preset number then press the MEMO button again to store that station at the selected number.
ENGLISH (4) Listening to preset stations (remote control unit only) Example: Listening to the station preset at number P03 (This operation is only possible from the remote control unit.) Set the remote control selector switches Switch1 to DVD Switch2 to TUNER 1 Use the “+” and “–” preset buttons to select preset number “3” or press the “3” button on the numeric keypad to display preset number “P03”.
ENGLISH (6) RDS search Use this function to automatically tune to FM stations that provide RDS service. 1 Set the band to “FM”. Remote control unit 2 Set the remote control selector switches Switch1 to DVD Switch2 to TUNER 2 1 3 Press the RDS button until “RDS” appears on the display. Remote control unit 3 Press the TUNING + (UP) or – (DOWN) button to automatically begin the RDS search operation.
ENGLISH (8) TP search Use this function to find RDS stations broadcasting traffic program (TP stations). 1 3 Set the band to “FM”. Press the TUNING + (UP) or – (DOWN) button TP search begins. Remote control unit 2 Press the RDS button until “TP” appears on the display. Remote control unit 4 Remote control unit The station name is displayed on the display after searching stops. • If no TP station is found when all the frequencies are searched, “NO PROGRAMME” is displayed.
ENGLISH 12 EXPANDING TO A 6.1- OR 7.1-CHANNEL SYSTEM • The DHT-M330DV is equipped with a decoder function allowing 6.1- or 7.1-channel playback (Dolby Digital EX, DTS-ES, Dolby Pro-Logic IIx, etc.), as well as PRE OUT connectors for surround back channels (SBL and SBR). • The DHT-M330DV is also equipped with a pre-out connector for a subwoofer channel, so the system can be improved using a commercially available superwoofer with built-in amplifier.
ENGLISH (3) 6.1- or 7.1-channel surround playback z Changing the Quick Setup settings At “SPEAKER SETUP” under “Quick Setup procedure” (page 27), select the configuration to be used, “6.1CH” or “7.1CH”. x Checking and adjusting the playback level using test tones Before playing, use test tones to check and adjust the playback level of the different speakers. (Page 33) • Depending on the 6.1/7.1-channel setting, the surround back channel is also displayed and can be set.
ENGLISH 13 DOLBY/DTS SURROUND Surround The AVR-M330 is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same sense of presence as in a movie theater. Dolby Surround (1) Dolby Digital Dolby Digital is the multi-channel digital signal format developed by Dolby Laboratories. Dolby Digital consists of up to “5.
ENGLISH Sources recorded in Dolby Surround These are sources in which three or more channels of surround have been recorded as two channels of signals using Dolby Surround encoding technology. Dolby Surround is used for the sound tracks of movies recorded on DVDs, LDs and Video cassettes to be played on stereo VCRs, as well as for the stereo broadcast signals of FM radio, TV, satellite broadcasts and cable TV.
ENGLISH DTS-ES Extended Surround TM DTS-ES Extended Surround is a new multi-channel digital signal format developed by Digital Theater Systems Inc. While offering high compatibility with the conventional DTS Digital Surround format, DTS-ES Extended Surround greatly improves the 360-degree surround impression and space expression thanks to further expanded surround signals. This format has been used professionally in movie theaters since 1999. In addition to the 5.
ENGLISH Dolby Virtual Speaker Dolby Virtual Speaker technology uses proprietary technology of Dolby Laboratories to create a virtual surround sound field using only two speakers for the front channels, allowing the user to experience sound as if surround speakers were actually being used. 2 Features of Dolby Virtual Speaker sound B B B B Accurate surround sound field positioning The virtual surround speakers are positioned at 105° to the left and 105° to the right.
ENGLISH 14 USING THE SLEEP TIMER (1) Setting the sleep timer (remote control unit only) • The included remote control unit can be used to turn the power to the standby mode after a maximum of 120 minutes. (Sleep timer) • Use this function to automatically switch the power to the standby mode after a specific amount of time (minutes). Example: To set the power to the standby mode in 50 minutes according to the clock. Be sure to correct the current time setting.
ENGLISH 15 SYSTEM FUNCTIONS 2 Making system connections between the AVR-M330 and the DVD player (DVD-M330) makes operation even easier. (For instructions on connections, refer to “Connecting the audio components” on pages 14.) 2 System functions will not work properly if the input/output function settings are not right for the connected components. Be sure to set the input/output functions for the components being used. (See page 28.
ENGLI 16 LAST FUNCTION MEMORY • This unit is equipped with a last function memory which stores the input and output setting conditions as they were immediately before the power is switched off. This function eliminates the need to perform complicated resettings when the power is switched on. • The unit is also equipped with a back-up memory. This function provides memory storage when the power switch is off and with the power cord disconnected.
ENGLISH 18 TROUBLESHOOTING Check again before assuming the player is malfunctioning 2 Are all the connections correct ? 2 Are you following the instructions in the manual ? 2 Are the speakers and other components operating properly ? If this unit does not seem to be functioning properly, check the table below. If this does not solve the problem, this unit may be damaged. Turn off the power, unplug the power cord from the power outlet, and contact your store of purchase or nearest Denon sales office.
ENGLI 19 SPECIFICATIONS 2 2 2 2 2 2 Audio Section • Power Amplifier Section Rated output: Output terminals: • Analog Section Input sensitivity/Input impedance: Frequency response: Signal-to-noise ratio: Tuner Section Reception frequency range: Receiving sensitivity: FM stereo separation: • Digital Section Digital input/output: Timer Section Timer: General Power supply: Power consumption: Maximum external dimensions: Weight: Remote Control Unit Remote control method: Power supply: Speakers SYS-M330 •
MEMO Downloaded 382 From TheatreSystem-Manual.
Downloaded From TheatreSystem-Manual.
TOKYO, JAPAN www.denon.com Downloaded From TheatreSystem-Manual.
