e Ver. 1 SERVICE MANUAL MODEL JP DP-200USB E3 E2 EK K2A E1C E1K EUT P P FULL AUTOMATIC TURNTABLE SYSTEM ● For purposes of improvement, specifications and design are subject to change without notice. ● Please use this service manual with referring to the operating instructions without fail. ● Some illustrations using in this service manual are slightly different from the actual set. e Denon Brand Company, D&M Holdings Inc. X0392 V.
SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. leakage current check Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. if the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
DIMENSION DP-200USB
WIRE ARRANGEMENT Lea SW f SW1 AC cord Sgnal wire DP-200USB Leaf SW
CARTRIDGE REPLACEMENT (The cartrige forms a single body with the head shell. Use the following procedure to replace it.) 1. Remove the screw on the bottom of the head shell as shown in the diagram. 2. Rotate the entire head shell gently in both directions. The neck of the head shell is attached to the pipe arm. Turn it gently until the shell comes loose. 3. Carefully remove the head shell. (Be careful not to break the lead wire.) 4. Remove the tip of the lead wire from the carridge terminal. 5.
BLOCK DIAGRAMS DP-200USB
METHOD OF ADJUSTMENT 1.Relationship between belt and pulley. Check that the belt is not touching the collars (A) of the motor pulley. If it is, remove the turntable and reattach the belt at the center of the turntable skirt. 2.Speed adjustment If the speed is off, adjust it with the variable resistor on the motor control board. Adjust for 33 r.p.m first, then set at 45 r.p.m and check. After adjusting, check the two speeds (33 and 45 r.p.m) once again. 3.
4.Stylus tip height adjustment (1) Adjust the stylus tip height under standard conditions. (Standard conditions: with the turntable, turntable sheet, and record set) (2) The stylus tip theight should be adjusted to about 6mm when returned (5-7mm at the outermost position for 17cm records). (3) If the stylus tip is too high, sound may be distorted and the stylus may not advance. If it is too low, it may scratch the record when returning. (4) Adjust using the lifter screw.
7 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 GP27 SCOR/GP28 BCLK/GP29 DATA/GP30 LRCK/GP31 SBDT/GP32 SBCK/GP33 GP23 VDD VSS NTRST RESETN IOVSS XTI XTO TEST XI XO IOVDD USBD+ USBDIOVSS PLL2VSS FILTER2 PLL2VDD PLL1VSS FILTER1 PLL1VDD ADIN5 ADIN4 ADIN3 ADIN2 GP02 GP01 XI16EN/SPIDI ECSN EOEN/GP38 EWEN EAD20/GP37 EAD19/GP36 EAD18/GP35 EAD17/GP34 WEN CASN SDCLK IOVSS IOVDD RASN CKE VSS VDD SDSCN UDQM/EAD16 LDQM/EAD15 BA1/EAD14 BA0/EAD
Terminal Function 10 DP-200USB
DP-200USB
DP-200USB
IS42S16100E-7TL (IC203） 13 DP-200USB
DP-200USB
SST39LF/VF400A (IC204） BLOCK DIAGRAM PIN FUNCTION 15 DP-200USB
PRINTED WIRING BOARDS REC P.W.B.
REC P.W.B.
PH/LI/SPEED/AC SW/AC/DC P.W.B.
PH/LI/SPEED/AC SW/AC/DC P.W.B.
NOTE FOR PARTS LIST 1. Parts for which "nsp" is indicated on this table cannot be supplied. 2. When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying. 3. Ordering part without stating its part number can not be supplied. 4. Part indicated with the mark "★" is not illustrated in the exploded view. 5. Not including General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.) 6.
PARTS LIST OF P.W.B. UNIT ＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊ P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts. ＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note:The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A.
Ref No. Part No.
PH/LI PCB ASS'Y Ref No. Part No.
Ref No. C622 C623 C624 C625 C626 C627 C628 C629,C630 Part No. 941134000430S 941134000510S 941134000520S nsp 941134000520S nsp 00D9587032806 nsp Part Name ELEC.CAPACITOR(22uF/25V,M,TAPING 5*11) ELEC. CAPACITOR(220uF/16V,M,105( ,TAPING 6*7,MINI) E.C.(4.7uF/25V,MINI) CHIP CAPACITOR(4700pF/50V,K,0603 TAPING,X7R) E.C.(4.7uF/25V,MINI) CHIP CAPACITOR(4700pF/50V,K,0603 TAPING,X7R) ELEC. CAPACITOR(100uF/16V,M,105 ,TAPING 6.
SPEED/AC SW/AC/DC PCB ASS'Y Ref No. Part No.
-MEMO- 26 DP-200USB
EXPLODED VIEWS WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
POINTS OF GREASING <φ1.2> (8.0mg <φ2.5>) <φ3.5> <φ1.5> <φ1.5> <φ1.5> (8.0mg <φ2.5>) <φ1.5> <φ1.5> <φ3.5> <φ2> <φ1.5> <φ1.5> <φ1.2> <φ2> <φ1.5> <φ1.5> <φ1.2> Grease CR-S Maker Note Daizo Corporation (Nichimoly) Synthetic oil based resin-use lithium grease PG671 Dow Corning Toray Co., Ltd. Non-silicone grease, COMPOSITION : Poly-α-olefin, Lithium soap, PTFE etc. KF-96H Shin-Etsu Chemical Co., Ltd. Dimethyl silicone fluid 100.000mm2/s G-488M Kanto Kasei Co., Ltd.
PARTS LIST OF EXPLODED VIEW ＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊ P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts. ＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note:The symbols in the column "Remarks" indicate the following destinations. BKE3 : U.S.A.
Ref.No. z z z z Part No.
Ref.No. Part No. Part Name 41 42 44 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 00D9410003902 00D9410025401 nsp nsp nsp nsp nsp 00D9410005803 00D9410007209 00D9410007403 00D9410007500 00D9410007607 00D9410008101 941472000660S 00D9410008004 941472000670S 941472000680S 00D9410008703 00D9410008907 00D9580035402 00D9410008800 941409000690S 00D9410009100 CAUTION LABEL(70*10mm,t=0.1mm) LABEL(BARE,36*8mm,t=1.2mm) RATING LABEL(97*25mm,t=0.08mm) RATING LABEL(97*25mm,t=0.08mm) SEGREGATE SHEET(87.
PACKING VIEW e y r u q t Q2 w Q3 Q1 Q0 i o Q1 Q3 PARTS LIST OF PACKING & ACCESSORIES ＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. BKE3 : U.S.A. & Canada model (Black model) BKE2 : Europe model (Black model) SPE2 : Europe model (Premium Silver model) Ref.No.
-MEMO- 33 DP-200USB
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
C 241 470u/10 C 242 0.1u R 238 47K C 221 0.0012u 0 R 235 0 R 236 0 R 237 C 220 0.
1 2 3 4 5 6 7 8 A 12V 12V B C 12V D E SCHEMATIC DIAGRAMS (2/3) F DP-200USB
1 2 3 4 5 6 7 8 A B C D E SCHEMATIC DIAGRAMS (3/3) F DP-200USB
