For U.S.A., Canada, Europe, U.K., Asia, China, Taiwan R.O.C., Korea & Japan model SERVICE MANUAL MODEL Ver. 1 DN-S1000 TABLE TOP SINGLE CD PLAYER 注 意 サービスをおこなう前に、このサービスマニュアルを 必ずお読みください。本機は、火災、感電、けがなど に対する安全性を確保するために、さまざまな配慮を おこなっており、また法的には「電気用品安全法」に もとづき、所定の許可を得て製造されております。 従ってサービスをおこなう際は、これらの安全性が維 持されるよう、このサービスマニュアルに記載されて いる注意事項を必ずお守りください。 本機の仕様は性能改良のため、予告なく変更すること があります。 ● 補修用性能部品の保有期間は、製造打切後8年です。 ● For purposes of improvement, specifications and design are subject to change without notice.
DN-S1000 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
DN-S1000 DISASSEMBLY (Follow the procedure below in reverse order when reassembling.) 1. Bottom Plate (1) Remove 6 screws 57 and pull out Bottom Plate. 57 Bottom Plate 57 2. Top Cover unit (1) Remove 6 screws 61 and 2 screws 59. (2) Disconnect FFC Cable. (3) Detach Top Cover unit. 61 61 59 61 59 FFC Cable 61 CX251 Top Cover Note: z Do not pull out aslant to prevent FFC cable damage. z Do not fail to pull AC cord from wall outlet before disconnect FFC Cable.
DN-S1000 3. Shield Bracket (1) Remove 4 screws 58 and 2 screws 67. (2) Detach Shield Bracket. 58 Shield Bracket 58 67 4. Mecha unit (1) Remove 2 screws 53 and 2 screws 55. (2) Disconnect FFC cable. (3) Detach Mecha Unit. 55 53 53 Mecha unit FFC Cable CX301 Note: z Do not pull out aslant to prevent FFC cable damage. z Do not fail to pull AC cord from wall outlet before disconnect the FFC cable.
DN-S1000 5. Power P.W.B. (1) Remove 5 screws 58, a screws 60 and a screws 61. (2) Detach Power P.W.B. 58 60 Power P.W.B. 61 6. Main P.W.B. (1) Short-circuit the short land above. (2) Remove a screws 54 and a screws 56. (3) Disconnect FFC Cable and FPC Cable. (4) Detach Main P.W.B. 54 Main P.W.B. FPC Cable 56 Short land for laser diode FFC Cable Note: z Do not pull out aslant to prevent FFC cable damage.
DN-S1000 7. CD Mecha (1) Remove 2 screws 53 and pull out Main Pwb Bracket. (2) Remove 2 screws 55 and pull out Disc Guide. Main Pwb Bracket 53 53 CD Mecha Disc Guide 55 55 8. Scratch Disc unit (1) Remove a screws 66 and pull out Scratch Disc unit.
DN-S1000 9. Disc Switch P.W.B. (1) Detach Slip mat, Anti-Static Sheet and Spring Plate. (2) Remove 4 screws 56. (3) Detach Disc Switch P.W.B. Slip Sheet Anti-Static Sheet Slip mat Spring Plate Disc Switch P.W.B. 56 56 10. Sensor P.W.B. and Scale unit (1) Remove 2 screws 56 and pull out Sensor Cover and Sensor P.W.B. (2) Remove a screw 51 and pull out Scale unit. 56 Sensor Cover Sensor P.W.B.
DN-S1000 BLOCK DIAGRAM MAIN UNIT POWER UNIT X'tal 11.2M LV393 25M 64M SDRAM D/A PCM1748 AMP Analog Out Digital Out ABCK/ALRCK CD MECHA DBCK/DLRCK SERVO DSP MN6627933 ±5VA ADATA Driver AN8785BS Head Amp AN2002A +8V +5V BCK/LRCK Data 3.
DN-S1000 CONFIRMING THE SERVO サービスモード What is Service Program サービスモードについて Service program is a special program intended for confirming servo functions etc. This manual use both as DN-S1000 and DN-D6000 ｻｰﾋﾞｽﾓｰﾄﾞは、ｻｰﾎﾞ状態などを確認するための特別なﾌﾟﾛｸﾞﾗﾑです。 このﾏﾆｭｱﾙは DN-S1000、DN-D6000 兼用です。 Required Measuring Implement 確認に必要な測定器具 Reference disc (TCD784 or CO-74176) ﾘﾌｧﾚﾝｽﾃﾞｨｽｸ：TCD784、CO-74176 1. Contents of Service Program 1.
DN-S1000 CUE button FLT all light check performed while button pressed. CUE ﾎﾞﾀﾝ ﾎﾞﾀﾝを押している間、FLT の全点灯ﾁｪｯｸを行います。 BEND+ button FLT all off check performed while button pressed. BEND+ ﾎﾞﾀﾝ ﾎﾞﾀﾝを押している間、FLT の全消灯ﾁｪｯｸを行います。 BEND- button BEND- ﾎﾞﾀﾝ Disc eject status set while button pressed. The disc loading/eject roller turns. The dirt can be cleaned off the roller by gently pressing a cotton swab with "Isopropyl alcohol", against the roller.
DN-S1000 Error Indication TR displays the track No. in MIN SEC Displays the time at which error occurred. which error occurred. ｴﾗｰ表示 FRAM CHARACTER ﾄﾗｯｸ H ＊＊＊＊ Operation count ｴﾗｰが発生したﾄﾗｯｸ番号 分 秒 ﾌﾚｰﾑ ｴﾗｰが発生した時間 (A ﾀｲﾑ ) E ＊＊＊＊ Error code ｷｬﾗｸﾀｰ H ＊＊＊＊ 動作回数 E ＊＊＊＊ ｴﾗｰｺｰﾄﾞ 4. µcom update 4. ﾏｲｺﾝｱｯﾌﾟﾃﾞｰﾄ With the DN-S1000 and DN-D6000, the system µcom and DSP can be updated from a disc.
DN-S1000 SEMICONDUCTORS ／半導体一覧表 Only major semiconductors are shown, general semiconductors etc. are omitted to list. 主な半導体を記載しています。汎用の半導体は記載を省略しています。 1. IC’s MN102H730F (IC101) 96 65 97 64 TOP VIEW 128 33 32 1 MN102H730F Terminal Function Pin No. Pin Name Simbol I/O DET Ext Ini Res Function 1 CS0_ CS0_ O - Pu - - Ext. memory chip select 0 (Frash ROM CS) 2 CS1_ CS1_ O - - - - Not used 3 D00 DQ0 I/O - - - - Ext.
DN-S1000 Pin No. Pin Name Simbol I/O DET Ext Ini Res Function 29 VDD VDD - - - - - Power (+3.3V) 30 OSCI OSCI I - - - - Oscillation input, 32.
DN-S1000 Pin No. Pin Name 80 PD4 81 PD5 82 83 Simbol I/O DET Ext Ini Res Function KIN0 I - Pu - H DNS1000: Key scan input signal 0 EJECT I - Pu - H DND6000: Disc eject button input signal KIN1 I - Pu - H DNS1000: Key scan input signal 1 CDSEL I - Pu - H DND6000: CD mecha.
DN-S1000 ADSP-BF531 (IC401) 176 1 133 132 PIN 1 TOP VIEW 89 88 44 45 ADSP-BF531 Terminal Function Pin No. Pin Name Symbol I/O DET Ext Ini Res Function 1 GND GND - - - - - GND 2 GND GND - - - - - GND 3 GND GND - - - - - GND 4 VROUT2 O - - - - Ext. FET drive output 2 5 VROUT1 VROUT1 O - - - - Ext. FET drive output 1 6 VDDEXT VDDEXT I - - - - I/O power supply (+3.
DN-S1000 Pin No. Pin Name Symbol I/O DET Ext Ini Res Function 40 GND GND - - - - - GND 41 GND GND - - - - - GND 42 GND GND - - - - - GND 43 GND GND - - - - - GND 44 GND GND - - - - - GND 45 VDDEXT VDDEXT I - - - - I/O power supply (+3.
DN-S1000 Pin No. Pin Name Symbol I/O DET Ext Ini Res Function 95 BMODE1 BMODE1 I - - - - Boot mode strap 1 96 BMODE0 BMODE0 I - - - - Boot mode strap 0 97 GND GND - - - - - GND 98 DATA15 D15 I/O - - - - Ext. bus data 15 99 DATA14 D14 I/O - - - - Ext. bus data 14 100 DATA13 D13 I/O - - - - Ext. bus data 13 101 DATA12 D12 I/O - - - - Ext. bus data 12 102 DATA11 D11 I/O - - - - Ext. bus data 11 103 DATA10 D10 I/O - - - - Ext.
DN-S1000 Pin No. Pin Name Symbol I/O DET Ext Ini Res Function 150 _ABE1 SDQM1 I/O - - - - SDRAM data mask 1 151 _ABE0 SDQM0 I/O - - - - SDRAM data mask 0 O - - H H Async memory write enable O - - H H Async memory read enable O - - - - Async memory output enable 152 _AWE 153 _ARE _ARE 154 _AOE 155 GND GND - - - - - GND 156 VDDEXT VDDEXT I - - - - I/O power supply (+3.3V) 157 VDDINT VDDINT I - - - - Core power supply (+1.
DN-S1000 MN6627933 (IC201) MN6627933 Terminal Function Pin No.
DN-S1000 Pin No.
DN-S1000 Pin No. Pin Name I/O Function 73 MDATA I µcom command data signal input 74 MLD I µcom command load signal input 75 *STAT O Status signal output 76 *BLKCK O Subcode block clock signal output 77 *SMCK O 4.2336MHz/8.4672MHz clock signal output 78 *PMCK O 88.
DN-S1000 M66005AFP (IC601) 1 1 0 2 0 9 3 0 8 4 0 7 5 0 6 6 0 5 7 0 4 8 D IG D IG D IG D IG R E S E C S C S D A T 0 3 9 0 2 1 0 S E S E S E S E S E S E S E S E S E 1 1 1 2 T 1 3 S 1 4 K 1 5 A 1 6 P I 1 7 P O 1 8 V c c 1 1 9 X out 2 0 X in 2 1 V s s 2 2 G 35 2 3 G 34 2 4 G 33 2 5 G 32 2 6 G 31 2 7 G 30 2 8 G 29 2 9 G 28 3 0 G 27 3 1 V p 3 2 0 1 0 0 6 4 D 6 3 D 6 2 D 6 1 D 6 0 V 5 9 S 5 8 S 5 7 S 5 6 S 5 5 S 5 4 S 5 3 S 5 2 S 5 1 S 5 0 S 4 9 S 4 8 S 4 7 S 4 6 S 4 5 S 4 4 S 4 3 S 4 2 S 4
DN-S1000 AN8785SB (IC202) L: All mute Hiz: ch2,4 ON H: Active 1 [ Others ] [ Loading ] Standby PVcc2 28 D2+ D2- [ Traverse ] [ Spindle ] D4- D3- M 16 7 10 12 D4+ M 11 D1+ D5- D5+ PVcc1 13 28 26 25 M 17 18 [ Tracking ] [ Focus ] D3+ PVcc3 D1- 14 1 19 24 22 Protection Circuit 8 21 14 15 Standby Band-gap Vcc/Vref Reser Circuit 4 IN-+ -+ -+ -+ -+ -+ -+ -+ -+ -+ 5 IN+ -+ 1.25V 3 OUT -+ -+ -+ -+ -+ -+ 6 Vref switch 7 9 IN2+ 0.1µ 23 20 15 21 8 ch.
DN-S1000 PCM1748 (IC106) BCK 1 16 SCK DATA 2 15 ML LRCK 3 14 MC DGND 4 13 MD VDD 5 12 ZEROL/NA VCC 6 11 ZEROR/ZEROA VOUTL 7 10 VCOM VOUTR 8 9 AGND PCM1748 BCK LRCK Serial Input I/F DAC 8x Oversampling Digital Filter with Function Controller ML Enhanced Multi-Level Delta-Sigma Modulator Function Control I/F VCOM DAC Output Amp and VOUTR Low-Pass Filter MD System Clock VCC AGND ZEROR 24 VDD Power Supply Zero Detect DGND System Clock Manager ZEROL SCK
DN-S1000 64M SDRAM (IC210) 128M SDRAM (IC402) Pin Assignment 1 54 Pin No. 22, 23~26, 29~35 20, 21 Pin Name A0~A11 BS0, BS1 2, 4, 5, 7, 8, DQ0~ 10,11, 13, 42, DQ15 44,45, 47, 48, 50, 51, 53 19 CS# Bank Select Data Input/Output 18 RAS# 17 16 15, 39 CAS# WE# UDQM/ LDQM 38 37 CLK CKE 1, 14, 27 28, 41, 54 3, 9, 43, 49 6, 12, 46, 52 36, 40 Vcc Vss VccQ VssQ NC 28 Description Multiplexed pins for row and column address. Row address: A0~A11. Column address: A0~A8.
DN-S1000 2.
DN-S1000 Segment Designation Anode Connection 27
DN-S1000 PRINTED WIRING BOARDS GU-3607 MAIN P.W.B.
DN-S1000 GU-3608 PANEL P.W.B.
DN-S1000 FOIL SIDE 30
DN-S1000 NOTE FOR PARTS LIST l Part indicated with the mark " " are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused. l When ordering of part, clearly indicate "1" and "I" (i) to avoid missupplying. l Ordering part without stating its part number can not be supplied. l Part indicated with the mark " " is not illustrated in the exploded view. l Not including Carbon Film Resister ±5%, 1/4W Type in the P.W.Board parts list.
DN-S1000 PARTS LIST OF P.W.B. UNIT ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります Note: The symbols in the column "Remarks" indicate the following destinations. E3: U.S.A. & Canada model E2: Europe model JP: Japan model GU-3607 MAIN P.W.B. UNIT ASS'Y Ref. No. Part No.
DN-S1000 Ref. No. C114 Part No.
DN-S1000 Ref. No. C239 Part No.
DN-S1000 Ref. No. Part No. Part Name X101 00D 399 0880 900 CSTLS32M0X53 X102 00D 399 0907 003 X'TAL(11.
DN-S1000 GU-3608 PANEL P.W.B. UNIT ASS'Y Ref. No. Part No.
DN-S1000 Ref. No. Part No.
DN-S1000 Ref. No. ! Part No.
DN-S1000 EXPLODED VIEW 30 Parts List 56 66 29 2-4 52 18 34 10 58 31 58 52 2-5 38 20 16 59 63 33 15 28 40 64 C 11 37 32 B 53 12 B 9 7 17 14 13 58 6 B 4 19 60 7 54 61 58 2-3 65 55 A 24 A 52 E C 8 56 23 56 D 2-2 67 27 26 22 39 56 53 51 25 5 61 61 55 35 21 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
DN-S1000 PARTS LIST OF EXPLODED VIEW ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 Note: The symbols in the column "Remarks" indicate the following destinations. E3: U.S.A. & Canada model E2: Europe model JP: Japan model Ref. No. Part No.
DN-S1000 Ref. No. ! Part No. Part Name Remarks Q'ty 42 00D 206 2085 003 AC CORD W/CON.DOM for JP 1 43 00D 415 0790 062 UL TUBE (14.3) BK for E2,JP for Ac cord 44 00D GEN 6760 F.CAUTION LABEL SUB for E3 45 00D 009 0196 063 25P FFC (1.0) 46 00D 009 0222 047 20P FFC (1.25) 47 00D 513 3826 004 E2 LASER CAUTION for E2 1 48 00D GEN 6335 -1 R.SHEET E3 for E3 1 48 00D GEN 6356 -1 R.SHEET E2 for E2 1 48 00D GEN 6686 R.SHEET J for JP 1 49 00D GEN 6154 MANUFAC.
DN-S1000 EXPLODED VIEW OF CD MECHANISM 42
DN-S1000 PARTS LIST OF CD MECHANISM UNIT ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 Ref. No. Part No.
DN-S1000 PACKING VIEW 202 201 202 203 ~ 208 210 PARTS LIST OF PACKING & ACCESSORIES ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 Note: The symbols in the column "Remarks" indicate the following destinations. E3: U.S.A. & Canada model E2: Europe model JP: Japan model Ref. No. Part No. 201 00D 505 0350 022 Part Name Remarks STYLEN PAPER Q'ty 1 202 00D 503 1486 009 CUSHION 2 203 00D 505 0038 030 POLY COVER 1 204 00D 511 4193 002 INST.
DN-S1000 WIRING DIAGRAM SLOT IN CD MECHA CD11-02 12PFFC SLEDSLED+ SPINDLE+ SPINDLELOAD START SW GND PICKUP INNER SW DISC SENSOR SENS LED LOAD+ LOADCHUCK SW 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 CX121 SLSL+ SP+ SP_LSSW GND _PISW DSENS SENS LED LOAD+ LOAD_CSW Pick Up 18PFFC Vcc Vref Vee N.C. E B C D A F MD VR LD GND F(-) T(-) T(+) F(+) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 CX181 Vcc Vref Vee N.C.
DN-S1000 NOTE FOR SCHEMATIC DIAGRAM 配線図について WARNING: Parts marked with this symbol ! have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. ! 印の部品は安全を維持するために重要な部品です。 従って交換時は必ず指定の部品を使用してください。 注） CAUTION: (1) 指定なき抵抗値は Ω、ｋ は ｋΩ、M は MΩ を示す。 Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.
DN-S1000 SCHEMATIC DIAGRAMS (1/3) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (1/3) H GU-3607 MAIN UNIT (1/2) 47
DN-S1000 SCHEMATIC DIAGRAMS (2/3) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (2/3) H GU-3607 MAIN UNIT (2/2) 48
DN-S1000 SCHEMATIC DIAGRAMS (3/3) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F SIGNAL LINE G SCHEMATIC DIAGRAMS (3/3) GU-3608-1 PANEL UNIT GU-3608-2 SLIDE_VR UNIT GU-3608-3 DISC_SENSOR UNIT GU-3608-4 DISC_SWITCH UNIT GU-3608-5 POWER UNIT H 49
