User Guide

9
DN-X400
1
16
17 32
33
48
4964
SEMICONDUCTORS


 IC’s
TMP86CM41F-3GH8 Terminal Function
TMP86CM41F-3GH8 (Main unit : IC314)
FunctionI/O DET Ext Ini Res
No.
Name
1VSS VSS —————GND
2XIN XIN — — — — — Osc. input pin, 16.00MHz
3XOUT XOUT — — — — — Osc. output pin
4 TEST(H:Vup) TEST — — — — — Fixed to GND
5VDD VDD — — — — — Power (+5.0V)
6 P21 STOP1 O — Pu H H Fader start CD1 back cue output
7 P22 PLAY1 O — Pu H H Fader start CD1 play start output
8 RESET_ RESET_ — — — — — Reset input
9 P20 ASWST0 O — Pu L H Analog SW data strobe signal 0
10 P30 YBLKCK O — — H — DIT sub code block clock
11 P31 ASWST2 O — Pd L L Analog SW data strobe signal 2
12 P32 ASWST3 O — Pd L L Analog SW data strobe signal 3
13 P33(SCK_) ASWCLK O — — L — Clock for analog SW data transfer
14 P34 LVM1 O — Pu H H Stereo level (ProgLch&Rch), L: Sel
15 P35(SO) ASWDAT O — — L — Analog SW data
16 P36 LVM2 O — Pu H H MONO LEVEL(CueAllMix&ProgAllMix), L: Sel
17 P37 ASWST1 O — Pd L L Analog SW data strobe signal 1
18 P40 — O — — L — Not used
19 (RxD1) — O — — L — Not used
20 (TxD1) — O — — L — Not used
21 P43 MUTE O — Pu H H Output mute, H: Mute
22 P44 PLAY2 O — Pu H H Fader start CD2 play start output
23 P45 STOP2 O — Pu H H Fader start CD2 back cue output
24 P46(INT3) TGSW3 I Ed Pu — — SW input interrupt signal for CH3 line select (PANEL1-B)
25 P47(INT4) TGSW4 I Ed Pu — — SW input interrupt signal for CH4 line select (PANEL1-B)
26 (AIN00) KEYIN10 I — Pu — H Key input 10 (PANEL1-B)
27 (AIN01) KEYIN12 I — Pu — H Key input 12 (PANEL1-B)
28 (AIN02) KEYIN13 I — Pu — H Key input 13 (ASSIGN-A) (PANEL1-B)
29 (AIN03) KEYIN11 I — Pu — H Key input 11 (PANEL1-F)
30 (AIN04) KEYIN14 I — Pu — H Key input 14 (ASSIGN-B) (PANEL1-F)
31 (AIN05) KEYIN20 I — Pu — H Key input 20 (PANEL2)
32 (AIN06) LVM-L I — — — — Signal input for level meter Lch
33 (AIN07) LVM-R I — — — — Signal input for level meter Rch
34 (AIN10) CRS-F I — — — — Cross fader voltage input signal
35 (AIN11) CH1-F I — — — — CH1 fader voltage input signal
36 (AIN12) CH2-F I — — — — CH2 fader voltage input signal
37 (AIN13) CONTOUR I — — — — Contour voltage input signal
38 (AIN14) — I — — — L Fixed to GND
Symbol