Ver. 1 SERVICE MANUAL MODEL DN-S700 JP E3 E2 EK E2A E2C E1K EUT 3 3 TABLE TOP SINGLE CD/MP3 PLAYER ● For purposes of improvement, specifications and design are subject to change without notice. ● Please use this service manual with referring to the operating instructions without fail. ● Some illustrations using in this service manual are slightly different from the actual set. PROFESSIONAL BUSINESS COMPANY X0457 V.
SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. if the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
232 m m DIMENSION 88 m m 106.
WIRE ARRANGEMENT If wire bundles are untied or moved to perform adjustment or parts replacement etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation.
DISASSEMBLY • Disassemble in order of the arrow of the figure of following flow. • In the case of the re-assembling, assemble it in order of the reverse of the following flow. • In the case of the re-assembling, observe "attention of assembling" it. TOP / BOTTOM Refer to "DISASSEMBLY 1.TOP / BOTTOM" and "EXPLODED VIEW" TOP BOTTOM SWITCHING POWER VFD/CONTROL PCB ASS'Y SLOT-IN FEEDER MECHA ASS'Y Refer to "DISASSEMBLY 2.SWITCHING POWER Refer to "DISASSEMBLY 3.VFD/CONTROL Refer to "DISASSEMBLY 6.
1. TOP / BOTTOM Proceeding : TOP / BOTTOM (1) Remove the screws. Direction of photograph: B Direction of photograph: C Direction of photograph: D (2) Disconnect the connector wires and FFC cable. CN1 CN3 CN2 Direction of photograph: A Rearrange the wiring of the wire. Refer to the WIRE ARRANGEMENT (4 page).
2. SWITCHING POWER Proceeding : TOP / BOTTOM → TOP → SWITCHING POWER (1) Remove the screws, then detach the ISOLATION COVER ASS'Y.
3. VFD/CONTROL PCB ASS'Y Proceeding : TOP / BOTTOM → TOP → VFD/CONTROL PCB ASS'Y (1) Pull up the KNOB, then remove the NUT. NUT KNOB (2) Remove the screws, then detach the ISOLATION COVER ASS'Y. Direction of photograph: B ISOLATION COVER ASS'Y (3) Disconnect the FFC cable, then remove the screws.
4. TURNTABLE ASS'Y Proceeding : TOP / BOTTOM → TOP → VFD/CONTROL PCB ASS'Y → TURNTABLE ASS'Y (1) Detach the KNOB, then remove the E RING.. KNOB E RING Direction of photograph: B KNOB 5. TURNTABLE FRAME Proceeding : TOP / BOTTOM → TOP → VFD/CONTROL PCB ASS'Y → TURNTABLE ASS'Y → TURNTABLE FRAME (1) Remove the screws.
6. SLOT-IN FEEDER MECHA ASS'Y Proceeding : TOP / BOTTOM → BOTTOM → SLOT-IN FEEDER MECHA ASS'Y (1) Disconnect the FFC cable and connector wires, then remove the screws. FFC cable CN11 FFC cable CN102 7. MAIN PCB ASS'Y Proceeding : TOP / BOTTOM → BOTTOM → SLOT-IN FEEDER MECHA ASS'Y → MAIN PCB ASS'Y Please refer to "EXPLODED VIEW" for the disassembly method of MAIN PCB ASS’Y.
SERVICE MODE CONFIRMING THE SERVO What is Service Program Service program is a special program intended for confirming servo functions etc. This manual use as DN-S700 Required Measuring Implement Reference disc (TCD784 or CO-74176) 1. Contents of Service Program Turn on the power while pressing both B button and the PARAMETER knob to set the service mode of DN-S700.
CUE button FLT all light check performed while button pressed. BEND- button FLT all off check performed while button pressed. The disc loading/eject roller turns. The dirt can be cleaned off the roller by gently pressing a cotton swab with "Isopropyl alcohol", against the roller. (Perform this operation with the top panel/cover removed and the disc ejected.) Servo automatic adjustment read-out value Adjustment Item Adjustment Value indication at character portions.
Error Indication TR displays the track No. in MIN SEC FRAM Displays the time at which error occurred. which error occurred. CHARACTER H ＊＊＊＊ Operation count E ＊＊＊＊ Error code 4. µcom update With the DN-S700, the servo μcom, system μcom and DSP can be updated from a disc. (1) Creating the update disc Use the procedure described below to create the disc for updating the servo system microprocessor and DSP.
TROUBLE SHOOTING 㪝㪣㪦㪮㩷㪚㪟㪘㪩㪫㩷㪥㪦㪅㪈䇭㩿㪤㪘㪠㪥㪆㪧㪦㪮㪜㪩㩷㪬㪥㪠㪫㪀 䇭㪫㪿㪼㩷㫇㫆㫎㪼㫉㩷㪺㪸㫅㫅㫆㫋㩷㪹㪼㩷㫋㫌㫉㫅㪼㪻㩷㫆㫅㪅 㪥㫆 䇭㪠㫊㩷㫋㪿㪼㩷㪽㫌㫊㪼㩷㫅㪸㫆㫉㫄㪸㫃䋿 㪰㪼㫊 㪠㫊㩷㫅㫆㫉㫄㪸㫃㩷㫊㫋㪸㫋㪼㩷㫉㪼㫊㫋㫆㫉㪼㪻㩷㫎㪿㪼㫅㩷㫆㫅㪺㪼㩷㫌㫅㫇㫃㫌㪾㪾㪼㪻 㫇㫆㫎㪼㫉㩷㪺㫆㫉㪻㩷㫀㫊㩷㫇㫃㫌㪾㪾㪼㪻㩷㪸㪾㪸㫀㫅㩷㪸㪽㫋㪼㫉㩷㫊㪼㫍㪼㫉㪸㫃㩷㫊㪼㪺㫆㫅㪻㫊㪖 㪥㫆 㪰㪼㫊 㪥㫆 㩷㩷㪠㫊㩷㫋㪿㪼㩷㪂㪎㪭㩷㫃㫀㫅㪼㩷㫍㫆㫃㫋㪸㪾㪼㩷㫅㫆㫉㫄㪸㫃㪖 㪰㪼㫊 㪥㫆 㩷㩷㪠㫊㩷㫋㪿㪼㩷㪂㪌㪭㩷㫃㫀㫅㪼㩷㫍㫆㫃㫋㪸㪾㪼㩷㫅㫆㫉㫄㪸㫃㪖 㪚㪿㪼㪺㫂㩷㫀㪽㩷㫋㪿㪼㫉㪼㩷㫀㫊㩷㪸㫅㫐㩷㫃㪼㪸㫂㩷㫆㫉㩷㫊㪿㫆㫉㫋㪄㪺㫀㫉㪺㫌㫀㫋㫀㫅㪾㩷㫆㫅㩷㫋㪿㪼 㫇㫉㫀㫄㪸㫉㫐㩷㫆㫉㩷㫊㪼㪺㫆㫅㪻㫃㫐㩷㪺㫀㫉㪺㫌㫀㫋㩷㪺㫆㫄㫇㫆㫅㪼㫅㫋㩷㫆㪽㩷㪪㪮㪠㪫㪚㪟㪠㪥㪞㩷㪧㪦㪮㪜㪩 㪪㪬㪧㪧㪣㪰㩷㪬㪥㪠㪫㪃㩷㪸㫅㪻㩷㫉㪼㫇㫃㪸㪺㪼㩷㫀㫋㩷㫀㪽㩷㪻㪼㪽㪼㪺㫋㫀㫍㪼㪅 㪰㪼㫊 㪥㫆 㩷㩷㪠㫊㩷㫋㪿㪼㪄㪏㪭㩷㫃㫀㫅㪼㩷㫍㫆㫃㫋㪸㪾㪼㩷㫅㫆㫉㫄㪸㫃㪖 㪰㪼㫊 㪥㫆 䇭㪠㫊㩷㫋㪿㪼㩷
㪝㪣㪦㪮㩷㪚㪟㪘㪩㪫㩷㪥㪦㪅㪋䇭㩿㪧㪘㪥㪜㪣㩷㪬㪥㪠㪫㪀 䇭㪫㪿㪼㩷㫂㪼㫐㩷㫆㫇㪼㫉㪸㫋㫀㫆㫅㩷㫀㫊㩷㫅㫆㫋㩷㪽㫌㫅㪺㫋㫀㫆㫅㫀㫅㪾㪅 㪥㫆 㪘㫉㪼㩷㫋㪿㪼㩷㪺㫆㫅㫋㪸㪺㫋㩷㫇㫆㫀㫅㫋㩷㪸㫅㪻㩷㫋㪿㪼㩷㫀㫅㫊㫋㪸㫃㫃㪸㫋㫀㫆㫅㩷㫊㫋㪸㫋㪼㩷㫆㪽㩷㫋㪿㪼㩷㫋㪸㪺㫋 㫊㫎㫀㫋㪺㪿㪼㫊㩷㫅㫆㫉㫄㪸㫃㪖 㪩㪼㪄㫀㫅㫊㫋㪸㫃㫃㩷㫋㪿㪼㩷㫊㫎㫀㫋㪺㪿㪼㫊㩷㪺㫆㫉㫉㪼㪺㫋㫃㫐㩷㫆㫉㩷㫉㪼㫇㫃㪸㪺㪼㩷㫋㪿㪼㩷㫇㫆㫆㫉㩷㫊㫎㫀㫋㪺㪿㪅 㪰㪼㫊 㪥㫆 㪛㫆㪼㫊㩷㪣㪜㪛㩷㫃㫀㪾㪿㫋㩷㪺㫆㫉㫉㪼㪺㫋㫃㫐㩷㪖 㪚㪿㪼㪺㫂㩷㫋㪿㪼㩷㪠㪚㪉㪇㪊䇮㪠㪚㪉㪇㪋㩷㪸㫅㪻㩷㫋㪿㪼㫀㫉㩷㫇㪼㫉㫀㫇㪿㪼㫉㫐㪃㩷㪸㫅㪻㩷㫊㪼㫉㫍㫀㪺㪼㩷㫀㫋㩷㫀㪽 㪻㪼㫋㪼㪺㫋㫀㫍㪼㪅 㪰㪼㫊 㪥㫆 㪮㪿㪼㫅㩷㫇㫉㪼㫊㫊㫀㫅㪾㩷㪼㪸㪺㪿㩷㫊㫎㫀㫋㪺㪿㪼㫊㪃㩷㪻㫆㩷㫋㪿㪼㩷㫍㫆㫃㫋㪸㪾㪼㩷㫆㪽㩷㪼㪸㪺㪿㩷㫇㫀㫅㩷㫆㪽 㪠㪚㪉㪇㪈㩿㫊㪿㫆㫎㫅㩷㪹㪼㫃㫆㫎㪀㩷㫀㫅㪺㫉㪼㪸㫊㪼㪖 㪚㪿㪼㪺㫂㩷㫋㪿㪼㩷㫊㫎㫀㫋㪺㪿㪼㫊㩷㪸㫅㪻㩷㫋㪿㪼㫀㫉㩷㫇㪼㫉㫀㫇㪿㪼㫉㫐㪃㩷㪸㫅㪻㩷㫊㪼㫉㫍㫀㪺㪼㩷㫀㫋㩷㫀㪽 㪻㪼㫋㪼㪺㫋㫀㫍㪼㪅 㪰㪼㫊 㪩㪼㫇㫃㪸㪺㪼㩷㪠㪚㪉㪇㪈㪅 㪝㪣
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1.
SERVO Block MIRR DFCT FOK SYSM SQSO SQCK SBSO EXCK DATA XLAT CLOK SENS SCOR C2PO WDCK EMPH WFCK XUGF GFS SCLK ATSK SSTP COUT CXD3059 Block diagram CPU Interface SERVO Interface Bass Boost Block LMUT MIRR DFCT FOK RMUT LPF LOCK MDP LPF DAC SFDR SRDR AOUT2 VREFR VREL AOUT1 EMPHI TFDR PWM Generator TRDR LRCKI PCMDI FFDR BCKI FRDR XTACN SERVO DSP XTSL CD Signal Processor Block TEI A/D Converter FEI Clock Generator XTAI XTAO VCTL Servo Auto Sequencer VPCO Digital OUT
CXD3059 Pin discription Power supply Pin No. Symbol I/O Description 1 MIRR I/O 1, 0 Mirror signal input/output. 2 DFCT I/O 1, 0 Defect signal input/output. 3 FOK I/O 1, 0 Focus OK signal input/output. 4 VSS — — 5 LOCK I/O 1, 0 6 MDP O 1, Z, 0 Spindle motor servo control output. 7 SSTP I 8 IOVSS1 — — 9 SFDR O 1, 0 Sled drive output. 10 SRDR O 1, 0 Sled drive output. 11 TFDR O 1, 0 Tracking drive output. 12 TRDR O 1, 0 Tracking drive output.
Power supply RFamp 3.3V ASYM 3.3V DC/DC 3.3V — Digital I/O = 3.3V Internal = 2.5V Pin No. Symbol 35 EQ_IN I Equalizer circuit input. 36 LD O APC amplifier output. 37 PD I 38 NC — 39 RFC 40 AVSS4 — 41 RFACO O RFAC signal output. 42 RFACI I RFAC signal input or EFM signal input. 43 AVDD3 — 44 BIAS I Asymmetry circuit constant current input. 45 ASYI I Asymmetry comparator voltage input. 46 ASYO O 47 VPCO O 1, Z, 0 Wide-band EFM PLL charge pump output.
Power supply Digital I/O = 3.3V Internal = 2.5V — X'tal 2.5V Lch 3.3V Rch 3.3V — Digital I/O = 3.3V Internal = 2.5V Pin No. Symbol 70 IOVDD2 — — 71 DOUT O 1, 0 72 TEST I Test pin. Normally GND. 73 TES1 I Test pin. Normally GND. 74 IOVss2 — — 75 NC — — 76 XVSS — — 77 XTAO O Crystal oscillation circuit output. 78 XTAI I Crystal oscillation circuit input. 79 XVDD — — Master clock power supply. 80 AVDD1 — — Analog power supply.
Power supply Pin No. Symbol 105 CLOK I/O I Description Serial data transfer clock input from CPU. 106 VDD — — 107 SENS O 1, 0 108 SCLK I 109 ATSK I/O 1, 0 Anti-shock input/output. 110 WFCK O 1, 0 WFCK output. 111 XUGF O 1, 0 XUGF output. Output MNT0, RFCK, SOUT by command switch. 112 XPCK O 1, 0 XPCK output. Output MNT1, SOCK by command switch. O 1, 0 GFS output. Output MNT2, XROF, XOLT by command switch. O 1, 0 C2PO output. Output MNT3, GTOP by command switch.
DN-S700
BA6392FP Pin discription 23 DN-S700
PTG5/XTAL BKGD/MS VREFL 58 57 56 55 54 53 52 51 50 64 PTC4 1 PTG4/KBI1P4 PTG6/EXTAL 59 PTD4/TPM2CLK/AD1P12 VSS 60 PTD5/AD1P13 PTC0/SCL1 61 PTD6/TPM1CLK/AD1P14 PTC1/SDA1 62 VREFH PTC2/MCLK 63 PTD7/KBI1P7/AD1P15 PTC3/TxD2 PTC5/RxD2 MC9S08AW32CPUE (IC103, 201) 49 48 PTG3/KBI1P3 2 47 PTD3/KBI1P6/AD1P11 RESET 3 46 PTD2/KBI1P5/AD1P10 PTF0/TPM1CH2 4 45 VSSAD PTF1/TPM1CH3 5 44 VDDAD PTF2/TPM1CH4 6 43 PTD1/AD1P9 PTF3/TPM1CH5 PTD0/AD1P8 IRQ 7 42 PTF4/TPM2CH0 8
MC9S08AW32CPUE Terminal Function Pin No.
PCM1716 (IC105) PIN ASSIGNMENTS LRCIN 1 28 ML/IIS DIN 2 27 MC/DM1 BCKIN 3 26 MD/DM0 CLKO 4 25 MUTE 2 DIN IN Serial Audio Data Input(1) 3 BCKIN IN Bit Clock Input for Serial Audio Data.(1) 4 CLKO OUT XTI 5 24 MODE XTO 6 23 CS/IWO DGND 7 22 RST PCM1716E 21 PIN NAME I/O 1 LRCIN IN DESCRIPTION Left and Right Clock Input. This clock is equal to the sampling rate - fS.(1) Buffered Output of Oscillator. Equivalent to System Clock.
74AHC595DR (IC203, 204) QB QC QD QE QF QG QH GND 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 VCC QA SER OE RCLK SRCLK SRCLR QH′ LC75710NE (IC205) 27 DN-S700
SCF5249LAG120 (U1) CD ROM Block Decoder Encoder CD Text Interface QSPI 8K byte I-Cache ColdFire V2 I Addr Gen I Fetch 96K Byte SRAM Instr Buf Dec&Sel Op A Gen & Ex B u s Serial Audio Interface 3 x I2S Rx 2 x I2S Tx C o n t r o l SPDIF/EBU Transmitter 12-bit ADC IDE Interface Flash Media Interface DUART EMAC Timers Debug Module DMA M-bus (I2C) SDRAM Cntr & Chip Selects General Purpose I/O SPDIF/EBU Receiver PLL Frequency Synthesizer Pin discription 144 QFP Pin Number Name Type 01 SCL/Q
144 QFP Pin Number Name Type 10 SCLK_OUT/GPIO15 I/O MemoryStick/SD 11 BCLKE O sdram clock enable output 12 SDA/QSPI_DIN I/O IIC data/QSPI data in function select is PLLCR(11) 13 DATA24 I/O data 14 A22 O SDRAM address / static adr 15 SDUDQM O SDRAM UDQM 16 EF/GPIO19 I/O error flag input 17 DATA25 I/O data 18 DATA26 I/O data 19 DATA27 I/O data 20 PAD-GND 21 DATA28 I/O data 22 DATA29 I/O data 23 SDATA3/GPIO56 I/O SD interface data line 24 DATA30 I/O d
144 QFP Pin Number Name Type 36 A20 O SDRAM address / static adr 37 TEST2 I test 38 SDRAM-CS1 O SDRAM chip select out 1 39 SDATA1_BS1/GPIO9 I/O Memory Stick / SD 40 SDRAS O SDRAM RAS 41 SDCAS O SDRAM CAS 42 SDWE O SDRAM write enable 43 SDLDQM O SDRAM LDQM 44 GPIO5 I/O GPIO5 45 QSPI_CS0/GPIO29 I/O QSPI chip select 0 46 QSPI_DOUT/GPIO26 I/O QSPI data out 47 GPIO6 I/O GPIO6 48 DATA21 I/O data 49 DATA19 I/O data 50 QSPI_CS2/GPIO21 I/O QSPI chip selec
144 QFP Pin Number Name Type 62 EBUIN2/GPI37 I 63 CORE-VDD 64 SCL2/GPIO3 I/O 65 RSTI I Reset 66 TOUT1/ADOUT/GPO35 O timer output 1 / AD output 67 LRCK2/GPIO44 O audio interfaces EBU out 1 68 OE O Output Enable 69 SDA2/GPIO55 I/O IIS2 data 70 SDATAO2/GPO41 O audio interfaces serial data output 2 71 SCLK2/GPIO48 I/O audio interfaces serial clock 2 72 PAD-GND 73 TEST3 I 74 SDATAO1/GPIO25 I/O audio interfaces serial data output 1 75 LRCK1 I/O audio interfaces w
144 QFP Pin Number Name Type 89 IDE-DIOW/GPIO14 I/O 90 CRIN I crystal 91 IDE-DIOR/GPIO13 I/O ide dior 92 IDE-IORDY/GPIO16 I/O ide iordy 93 MCLK1/GPO39 O Audio master clock output 1 94 MCLK2/GPO42 O Audio master clock output 2 95 XTRIM/GPO38 O audio interfaces X-tal trim 96 TRST/DSCLK I Debug / interrupt monitor output 2 97 CORE-VDD 98 RW_B O Bus write enable 99 TMS/BKPT I JTAG/debug 100 CORE-GND 101 TCK 102 PAD-GND 103 PST3/GPIO62 I/O debug 104 CNPSTCLK
144 QFP Pin Number Name Type 116 DDATA2/GPIO2 I/O 117 CTS2_B/ADIN3/GPI31 I 118 DDATA0/GPIO0 I/O 119 RXD2/GPI28/ADIN2 I second UART receive data input / AD input 2 120 TDSO O JTAG/debug 121 RTS2_B/GPO31 O second UART request to send 122 SDATAI3/GPI41 I audio interfaces serial data input 3 123 CTS1_B/GPI30 I first UART clear to send 124 TXD2/GPO28 O second UART transmit data output 125 RTS1_B/GPO30 O first UART request to send 126 EBUIN4/ADIN1/GPI39 I audio interface
K4S641632D (U2) VDD DQ0 VDDQ DQ1 DQ2 VSSQ DQ3 DQ4 VDDQ DQ5 DQ6 VSSQ DQ7 VDD LDQM WE CAS RAS CS BA0 BA1 A10/AP A0 A1 A2 A3 VDD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 VSS DQ15 VSSQ DQ14 DQ13 VDDQ DQ12 DQ11 VSSQ DQ10 DQ9 VDDQ DQ8 VSS N.C/RFU UDQM CLK CKE N.C A11 A9 A8 A7 A6 A5 A4 VSS 54Pin TSOP (II) (400mil x 875mil) (0.
K4S641632D Block diagram I/O Control Data Input Register LWE LDQM Bank Select 1M x 16 1M x 16 Output Buffer 1M x 16 Sense AMP Row Decoder ADD Row Buffer Refresh Counter Column Decoder Col.
XC9536-10-VQ44C (U8) 36 DN-S700
BLOCK DIAGRAM CONTROL PCB 1 FADER EEPROM AT93C46 LC75710NE VF D DRIVER VF D 3 2 74595 LED DRIVER LED K EY, ENCODER 1 CD LOADER P.I. MC9S08AW32 UI CPU 2 WHEEL SERVO PCB SLED + + M M - 3 2 1 RS232 DRI VE UNI T DI SC FADER L R G ISO. TX. CD PICK UP BA6392F P DRI VER 4641632 RAM M29W800 ROM BUF FER 74HC14 BUF FER D.
PRINTED WIRING BOARDS MAIN PCB UNIT (1/2) COMPONENT SIDE 38 DN-S700
MAIN PCB UNIT (2/2) FOIL SIDE 39 DN-S700
CONTROL PCB UNIT (1/2) COMPONENT SIDE 40 DN-S700
CONTROL PCB UNIT (2/2) FOIL SIDE 41 DN-S700
VFD PCB UNIT COMPONENT SIDE FOIL SIDE MOTOR PCB UNIT SW PCB UNIT COMPONENT SIDE 42 DN-S700
NOTE FOR PARTS LIST 1. Parts for which "nsp" is indicated on this table cannot be supplied. 2. When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying. 3. Ordering part without stating its part number can not be supplied. 4. Part indicated with the mark "★" is not illustrated in the exploded view. 5. Not including General-purpose Carbon Film Resistor in the P.W.Board parts list. (Refer to the Schematic Diagram for those parts.) 6.
PARTS LIST OF P.W.B. UNIT ＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. MAIN PCB ASS'Y Ref. No. Part No.
Ref. No. Part No. Part Name Remarks Q'ty New R104 nsp CHIP RESISTOR(10K OHM,1/10W,0603,J,TP ,50V) 412-CDVD2001-534 R105 nsp CHIP RESISTOR(100K OHM,1/10W,0603 ,J,TP ,50V) 412-CDVD2001-537 R106,127 nsp CHIP RESISTOR(1M OHM,1/10W,0603,J,TP ,50V) 412-CDVD2001-546 R107 nsp CHIP RESISTOR470K OHM,1/10W, 0603,J,TP,50V) 412-007USB-707 R108 nsp CHIP RESISTOR(3.
Ref. No. C27 C28 Part No. nsp Part Name CHIP CAPACITOR(0.1uF/50V,Z,0603 TYPE,Y5V) 00D9587032709 ELEC. CAPACITOR (220uF/10V,M,105 ℃ ,TAPING 6.3*7,MINI) Remarks Q'ty New 413-DCM280-773 413-HT801K-192 C29-31 nsp CHIP CAPACITOR(0.1uF/50V,Z,0603 TYPE,Y5V) 413-DCM280-773 C33 nsp CHIP CAPACITOR(0.1uF/50V,Z,0603 TYPE,Y5V) 413-DCM280-773 C39 nsp CHIP CAPACITOR(0.
Ref. No. C162 Part No. Part Name 00D9587032709 ELEC. CAPACITOR (220uF/10V,M,105 ℃ ,TAPING 6.3*7,MINI) C163,164 nsp CHIP CAPACITOR(0.1uF/50V,Z,0603 TYPE,Y5V) C165-168 00D9587056303 ELEC. CAPACITOR (10uF/25V,M,105 ℃ ,TAPING 4*7,MINI) C169,170 941139001560S POLYESTER CAPACITOR(0.0012uF/50V,J,TAPING) Remarks Q'ty New 413-HT801K-192 413-DCM280-773 413-SPPW3-235 413-HV3423K-343 C171,C172 nsp CHIP CAPACITOR(82pF/50V,J,0603 TYPE,NPO) 413-007USB-827 C174 nsp CHIP CAPACITOR(0.
Ref. No. Part No. Part Name Remarks Q'ty New L114 941119001530S INDUCTOR(100MH J 0707-444-W077) JK101 00D9587037102 2P RCA JACK(RJ-1060B*09-0520A) 420-100-189 JK102 00D9587037306 HEADPHONE JACK(φ3.5,2K6A/-3537*01-030) 420-HDJ7100-063 JK103 00D9587068100 1P RCA JACK(RJ-1081*31-0541A) 420-ST150-157 941661000320S POWER SW(SDDLB1177U-HF3) 403-C304-218 T101 00D9580020705 COIL(P-7GB) 415-RCC955A-091 W03 941612001880S 7P 2.
Control PCB ASS'Y Ref. No. Part No. Part Name Remarks Q'ty New SEMICONDUCTORS GROUP IC201 941239001660S CONTROL IC ASS'Y (MC9S08AW32CPUE,LQFP) 704-S700-8520 IC202 941239001600S IC(AT93C46DN-SH-B) 417-HDJ2460-657A IC203,204 00D9587058709 IC(74AHC595DR,SOP-16) 417-HDJ9800-643 Q201,202 00D9410046503 TRANSISTOR(DTC124EKAT146/DTC124EKA) 416-CDN88-044 D201 941263001070S LED(LTL1CHKGKNN,GREEN) 410-TT2A3SL-250 D201 nsp LED HOLDER(LED3-1A-B,H=1.
Ref. No. C207 Part No. Part Name Remarks 00D9587054907 ELEC. CAPACITOR (100uF/10V,M,105 ℃ ,TAPING 5*7,MINI) Q'ty New 413-HMA2200-5017 C208 nsp CHIP CAPACITOR(0.1uF/50V,Z,0603 TYPE,Y5V) 413-DCM280-773 C209,210 nsp CHIP CAPACITOR(0.01uF/50V,K,0603 TYPE,X7R) 413-DCM280-771 C211,212 nsp CHIP CAPACITOR(0.1uF/50V,Z,0603 TYPE,Y5V) 413-DCM280-773 C213 nsp CHIP CAPACITOR(0.01uF/50V,K,0603 TYPE,X7R) 413-DCM280-771 C214 nsp CHIP CAPACITOR(0.
---MEMO--- 51 DN-S700
EXPLODED VIEW WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
PARTS LIST OF EXPLODED VIEW ＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊ P.W.B. ASS'Y for which "nsp" is indicated on this table cannot be supplied. When repairing the P.W.B. ASS'Y, check the board parts table and order replacement parts. ＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3: U.S.A.
Ref. No. Part No. Part Name Remarks Q'ty New 37 nsp SCREW(SAE1018,PTP,M2.6*L8) 602-SL24F-099 24 38 nsp SCREW(SAE1018,ISOB,φ3*L8*P0.5) 602-HP1010K-178 3 39 nsp SCREW(SAE1018,BTB,φ3*L5) 602-QMX2BPM-322 2 40 nsp SCREW(SAE1018,WPTP,φ2.6*L6,CAPφ6.5) 602-ST150-434 2 41 nsp SCREW(SAE1018,PTB,φ3*L8) 602-DJ5500-452 8 42 nsp SCREW(SAE1018,PTB,φ2.6*L10) 602-MK8-604 2 43 nsp SCREW(SAE1018,ISOB,φ3*L10*P0.
PACKING VIEW PARTS LIST OF PACKING & ACCESSORIES ＊ Parts for which "nsp" is indicated on this table cannot be supplied. ＊ The parts listed below are for maintenance only, might differ from the parts used in the unit in appearances or dimensions. Note: The symbols in the column "Remarks" indicate the following destinations. E3 : U.S.A. & Canada model E2 : Europe mode Ref. No. Part No.
WIRING DIAGRAM CONTROL PCB CN1 SWITCHING POWER CN201A CONTROL PCB CN201A TO VFD PCB CN201B CN2 CN06B CN3 W03 AC POWER CORD W07 CN101 CN01 CN06A CN02 MAIN PCB CN102 CN03 CN1 CN11 56 DN-S700
---MEMO--- 57 DN-S700
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
L101 FB Q101 A933 C117 0.1 C102 100/10 C107 22/16 C103 A 100/10 A 3.3V L103 3.3V-3 FB C108 0.1 C112 C110 0.1 R103 C115 470K 100P ACKS ACKB D7 IC104 74HC04 22 1M -32V VF2 VF1 4 3 2 1 IC302 BD4745G R302 1 5 NC VCC 10K 2 SUB 3 4 GND VO C198 10P R111 0 R190 220 LRCK LRCK2 DB2 LRCK2 DB2 BCK2 BCK2 16.9M1 16.9M1 C121 C122 22/16 0.1 C123 D104 0.1 1SS132 R174 22 L111 FB C184 0.1 C150 0.01 CHASSIS C151 0.1 W07 4P C152 1000P CN02 1 2 3 C001 CN01 .
1 2 3 4 5 6 7 8 D C67 D01 D03 1SS132 1SS132 D02 1SS132 C21 0.1 0.1 A20 A18 A17 A9 A10 A11 A12 A13 C13 0.1 A23 A14 A15 A16 A19 A20 C05 0.1 K4S641632D R10 220 D3.3V R11 220 ACKS ACKS SCOR SCOR U6 74HC14 C06 C39 0.1 0.1 /OE ACKB R29 270 GPO55 D R09 220 DOUT C35 NC R12 0 R16 0 TP14 TP13 R17 0(NC) D3.3VL01 C30 0.1 C10 U5 0.1 C08 0.1 14 1A VDD 13 1Y 6A 12 2A 6Y 11 2Y 5A 10 3A 5Y 9 3Y 4A 8 GND 4Y FB C17 X1 R01 15P C07 0.1 DD TP22 TP12 TP11 C16 15P BCK 1M 16.
1 2 3 4 5 6 7 8 15K 3 R222 10K R220 15K R208 2.2K AD5V AD1 R218 560 WLB AD0 /OE STCP SHCP DS /OE STCP SHCP FILP PITCH VR201 10KB AD 5V SW203 SW204 SW205 PLAY CUE FLANGER ECHO FILTER D211 D212 D213 D214 6 10 B 16 SW206 SW207 FLIP SW208 SW209 A SW210 TIME/RELAY B KR3 C EXIT/RELOOP SW212 QUICK F. QUICK B.
1 2 3 4 5 6 7 8 A SW04 B C04 0.1 SW03 C03 0.1 SW02 GND SW4 SW3 SW2 SW1 CN01 1 2 3 4 5 MOTOR + CN901 A 1 2 - 2P C CON5 C02 0.1 SW01 SWITCH UNIT MOTOR UNIT C01 0.
