For U.S.A., Canada, Europe, Korea & Japan model 3 SERVICE MANUAL DN-C635 MODEL Ver. 3 Please refer to the MODIFICATION NOTICE. STEREO CD/MP3 PLAYER 注 意 サービスをおこなう前に、このサービスマニュアルを 必ずお読みください。本機は、火災、感電、けがなど に対する安全性を確保するために、さまざまな配慮を おこなっており、また法的には「電気用品安全法」に もとづき、所定の許可を得て製造されております。 従ってサービスをおこなう際は、これらの安全性が維 持されるよう、このサービスマニュアルに記載されて いる注意事項を必ずお守りください。 本機の仕様は性能改良のため、予告なく変更すること があります。 ● 補修用性能部品の保有期間は、製造打切後8年です。 ● For purposes of improvement, specifications and design are subject to change without notice.
DN-C635 2 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
DN-C635 DISASSEMBLY 3 各部のはずしかた (To reassemble, reverse disassembly) （組み立てるときは、逆の順序で行ってください。） 1. TOP COVER 1. TOP COVER (1) Remove 4 screws on both sides, 1 screw on the rear side, and 1 screw on the top side. (1) 両側面のねじ 4 本、後部のねじ 1 本と上面のねじ 1 本を はずします。 (2) Detach the Top Cover as shown in the arrow direction. (2) 上カバーを矢印の方向に取りはずします。 Top cover 2. FRONT PANEL 2. FRONT PANEL (1) Remove 2 upper screws, 3 lower screws and 2 screws on the both side.
DN-C635 3. MECHANISM UNIT 4 3. MECHANISM UNIT (1) Remove the Loder Panel. (1) ローダーパネルをはずします。 (2) Remove 4 screws fixing the Mechanism Unit and detach the Mechanism Unit.
DN-C635 5 BLOCK DIAGRAM 16M DRAM MUTE P. TRANS DIGITAL OUT CD MECH. MOTOR ACTUATOR ±5V DAC DRIVER DSP AN8785SB ST/MONO SELECT PCM1716E MUTE CD OUT ±12V MN662791 HEAD AMP CLOCK FIX/VARI SELECT P.U AN22002A CLOCK GEN. XLR OUT ±5V MUTE 3.3V 5V I/F TC74HCT7007 H/P OUT SYSTEM µCOM 4M FLASH ROM BUFFER MN102H60KDA SERIAL/ PARALLEL CONVERSION TALLY OUT PARALLEL KEY RS232C /422 LED SERIAL ±12V EXT IN ±5V +5V ROTALY REMOTE ENCORDER +3.
DN-C635 LEVEL DIAGRAM IC215 1 (7) RCA IC601 (602) 7 1 IC106 1 (7) +30dB +20dB +10dB 0dB 0dB -10dB +2.
DN-C635 7 WIRING DIAGRAM GU-3511-3 H/P UNIT CY231 CY052 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 CX231 GND 10 10 CAS IN 11 CAS OUT 12 11 CDOUT R GND CDOUT L GU-3511-2 1 SLIDE VR. 2 UNIT 3 CW041 4 1 2 3 4 PITCH MUTE PITCHC H/P R GND GND +3.3V H/P L CX041 EXT I/O 13 12 13 XLR UNIT -12V +12V GU-3511-5 MUTE (RD) GND KEYIN1 KEYIN0 PTHL KEYIN2 PLYL PRGL CUEL PUSH- TRSLB- TRSLA- GND GND +3.3V +3.
DN-C635 SERVICE PROGRAM サービスプログラム Required Measuring Implement 確認に必要な測定器具 z Reference disc (TCD784 or CO-74176) ● 1. What is Service Program サービスプログラムとは、サーボ機能等を確認するための特別なプログラムです。 2. µcom Version Check 2. マイコンバージョン確認 z Refer to "Preset Functions and Operations" of the instruction manual. z You can check the µcom version. ● ● 3.
DN-C635 6. Test Mode (Heat Run mode) 6. テストモード（ヒートランモード） z Switch on the power while pushing the FOLDER button and TIME button at the same time. "000TroHR0000" is displayed. And the tray is opened. (1)Hold the disc by the edges and place it on the disc tray. (2)Starting with the OPEN/CLOSE button, it repeats open/close of the tray and playback. ***TrxHRXXXX ***: Track No. x : o, c, s, t, r, and p XXXX: Cycle quantity All tracks are played back if the track count is less than 20.
DN-C635 Error Code Error 25 CONTENTS Error Code Retried searching repeatedly, but the sound could not be connected, resulting in an interruption of the sound. Error 26 The error rate when recording on the memory is over the regulation value. Error 27 The subcode jump more than regulation. Error 28 The servo was turned on when the power was turned on, but did not start up in the regulation time. Error 29 There was a subcode Q interruption, but the content of the subcode Q is abnormal.
DN-C635 CONFIRMING THE AUDIO オーディオの確認方法 1. Necessary Equipment for Adjustment 1. 必要な測定器具 Distortion--Factor Meter VTVM Low-Pass Filter (20kHz) AF Oscillator (20Hz ~ 20kHz, +18dBu) Reference Disc; DENON Audio Technical CD (38C39-7174) ひずみ率計 VTVM 測定用フィルタ (20kHz) AF オシレータ (20Hz ∼ 20kHz, +18dBu) 調整用ディスク ; DENON Audio Technical CD (38C39-7174) 2. Output Level Adjustment 2. 出力レベル調整 (1) Connect VTVM to the output connector of DN-C635.
DN-C635 SEMICONDUCTORS IC’s MN102H60KDA (IC103) 51 75 50 76 100 26 25 1 MN102H60KDA Terminal Function Pin No. Pin Name Symbol PCDMUTE I/O Det Ext Res Ini O - Pd L L Function 1 P60, WAIT, SBT2 Mute for CD 2 P61, _RE RD- O - Pu Hi-Z - Read signal 3 P62, _WEL WR- O - Pu Hi-Z - Write signal 4 P63, _WE, _WEH EXTIN- I - - Hi-Z - EXT.
DN-C635 Pin No.
DN-C635 Pin No. Pin Name Symbol I/O Det Ext Res Ini 14 Function 72 P75,SBO1 MLD O - - Hi-Z H DSP interface latch 73 TEST1 TEST1 I - Pu - - Pull up 33 - 50K 74 TEST2 TEST2 I - Pu - - Pull up 33 - 50K 75 _NMI -- I Lv Pu Hi-Z - Not used.
DN-C635 MN6627911AC (IC210) 41 60 40 61 80 21 20 1 MN6627911AC Terminal Function Pin No. Pin Name I/O I Function 1 DRVDD 2 D0 I/O Power supply for DRAM interface (Pin No.
DN-C635 Pin No.
DN-C635 AN8785SB (IC202) L: All mute Hiz: ch2,4 ON H: Active 1 [ Others ] [ Loading ] Standby PVcc2 28 D2+ D2- [ Traverse ] [ Spindle ] D4- D3- M 16 7 10 12 D4+ M 11 [ Tracking ] [ Focus ] D3+ PVcc3 D1- D1+ D5- D5+ PVcc1 13 28 26 25 M 17 18 14 1 19 24 22 Protection Circuit 8 21 14 15 Standby Band-gap Vcc/Vref Reser Circuit 4 IN-+ -+ -+ -+ -+ -+ -+ -+ -+ -+ 5 IN+ -+ 1.25V 3 OUT -+ -+ -+ -+ -+ -+ 6 Vref switch 7 0.1µ 9 IN2+ 23 20 15 21 8 ch.
DN-C635 PCM 1716E (IC211) LRCIN 1 28 ML/IIS DIN 2 27 MC/DM1 BCKIN 3 26 MD/DM0 CLKO 4 25 MUTE XTI 5 24 MODE XTO 6 23 CS/IWO DGND 7 22 RST VDD 8 21 ZERO 9 20 VCC2L AGND2R 10 19 AGND2L EXTR 11 18 EXTL VCC2R PIN NAME I/O 1 LRCIN IN Left and Right Clock Input. This clock is equal to the sampling rate - fS.(1) DESCRIPTION 2 DIN IN Serial Audio Data Input(1) 3 BCKIN IN Bit Clock Input for Serial Audio Data.(1) 4 CLKO OUT Buffered Output of Oscillator.
DN-C635 M66005FP (IC504) 1 1 0 2 0 9 3 0 8 4 0 7 5 0 6 6 0 5 7 0 4 8 D IG D IG D IG D IG R E S E C S C S D A T 0 3 9 0 2 1 0 0 1 1 1 0 0 1 2 S E S E S E S E S E S E S E S E S E T 1 3 S 1 4 K 1 5 A 1 6 P I 1 7 P O 1 8 V c c 1 1 9 X out 2 0 X in 2 1 V s s 2 2 G 35 2 3 G 34 2 4 G 33 2 5 G 32 2 6 G 31 2 7 G 30 2 8 G 29 2 9 G 28 3 0 G 27 3 1 V p 3 2 6 4 D 6 3 D 6 2 D 6 1 D 6 0 V 5 9 S 5 8 S 5 7 S 5 6 S 5 5 S 5 4 S 5 3 S 5 2 S 5 1 S 5 0 S 4 9 S 4 8 S 4 7 S 4 6 S 4 5 S 4 4 S 4 3 S 4 2 S
DN-C635 LOCK S2 S1 M2 M1 CKO Vss BU2090F (IC104) VDD TC9246F (IC217) Vss 1 16 15 14 13 12 11 10 9 DATA 2 Microcomputer Interface AN80L18RMS (IC208) Control Circuit 12-Bit Shift Register CLOCK 3 Lock Ditection Circuit Latch Q0 4 SW 5 16 VDD 15 Q11 GND 4 14 Q10 NC 3 13 Q9 Output Buffer (Open Drain) Q1 5 12 Q8 Programmable Counter VAR Q2 6 11 Q7 Phase Comparator Q3 7 10 Q6 Q4 8 9 Q5 Selector VDDA AMPI 5 6 7 8 XO 4 XI 3 VSSA 2 AMPO 1 PD VCO REF REF 1
DN-C635 FL DISPLAY BJ899GN (FL501) 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G S1 S3 S2 S2 S3 1-1 2-1 3-1 4-1 5-1 2a 3 b 3 c 1a 1 1 f 1g b 1 1 e c 1d Dp 13G 12G 1-2 1-3 1-4 1-5 1-6 1-7 [1G~11G] B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 [13G] Pin connection Pin No.
DN-C635 PRINTED WIRING BOARD GU-3510 MAIN P.W.B.
DN-C635 Parts List FOIL SIDE 23 23
DN-C635 GU-3511 DISPLAY P.W.B.
DN-C635 Parts List FOIL SIDE 25 25
DN-C635 NOTE FOR PARTS LIST l Part indicated with the mark " " are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused. l When ordering of part, clearly indicate "1" and "I" (i) to avoid missupplying. l Ordering part without stating its part number can not be supplied. l Part indicated with the mark " " is not illustrated in the exploded view. l Not including Carbon Film Resister ±5%, 1/4W Type in the P.W.Board parts list.
DN-C635 27 PARTS LIST OF P.W.B. UNIT Note: The symbols in the column "Remarks" indicate the following destinations. E3: U.S.A./Canada model E2K: Korea model E2: Europe model JP: Japan model 00DGU-3510 MAIN P.W.B. UNIT ASS'Y Ref. No. Part No. Part Name Remarks SEMICONDUCTORS GROUP IC101 00D GEN 6322 IC102 00D 263 0913 905 PST600C TP DNC635 SYSTEM ROM IC103 00D 262 3171 000 MN102H60KDA IC104 00D 262 2745 903 BU2090F(E2) 4M FLASH MEM.
DN-C635 Ref. No. Part No. Part Name D901,902 00D 276 0717 903 1SS355 TE-17 D903,904 00D 276 0550 908 1SR139-200T-62 D906 00D 276 0550 908 1SR139-200T-62 D908 00D 276 0550 908 1SR139-200T-62 D910 00D 276 0550 908 1SR139-200T-62 D912 00D 276 0550 908 1SR139-200T-62 D913 00D 276 0338 007 S4VB20F +C ZD101-108 00D 276 0692 905 RD24SB-T1 ZD201 00D 276 0450 901 HZS2B-1TD +C ZD901 00D 276 0643 983 MTZJ5.
DN-C635 Ref. No. Part No.
DN-C635 Ref. No. Part No.
DN-C635 Ref. No. Part No.
DN-C635 Ref. No. Part No.
DN-C635 Ref. No. Part No.
DN-C635 34 00DGU-3511/3511A/3511B DISPLAY P.W.B. UNIT ASS'Y Ref. No. Part No.
DN-C635 Ref. No. Part No.
DN-C635 Ref. No. ! Part No. Part Name C804 00D 257 0512 903 CK73F1E104ZT +1608 C805-807 00D 257 0511 904 CK73F1H103ZT +1608 C983 00D 253 8022 707 CK45F2EAC103MC Remarks Q'ty 36 New OTHERS PARTS GROUP CW041 00D 203 6181 098 4P KR-DS CON CORD CW052 00D 203 8224 047 5P PH-SAN CON.CORD * CW081 00D 204 2451 042 8P EH-SCN CON.CORD * CW131 00D 204 6253 026 13P KR-DA CON CORD CX021 00D 205 0581 001 2P VH CONNECTOR BASE CX022 00D 205 0768 002 2P VH CON.
DN-C635 EXPLODED VIEW WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
DN-C635 38 PARTS LIST OF EXPLODED VIEW Note: The symbols in the column "Remarks" indicate the following destinations. E3: U.S.A./Canada model E2K: Korea model E2: Europe model JP: Japan model Ref.No. Part No. Remarks Q'ty 1 00DGU-3510 MAIN P.W.B. UNIT ASS'Y 2 00DGU-3511 DISPLAY P.W.B. UNIT ASS'Y for E3 1 2 00DGU-3511A DISPLAY P.W.B. UNIT ASS'Y for E2, E2K 1 2 00DGU-3511B DISPLAY P.W.B. UNIT ASS'Y for JP 1 2-1 FLT UNIT 2-2 SLIDE VR.
DN-C635 Ref.No. ★ Part No.
DN-C635 40 EXPLODED VIEW OF CD MECHANISM UNIT (CD11FT3NF) 2 1 3 4 4 3 A 20 17 3 16 8 16 7 11 B 2 6 12 C 1 10 5 15 9 18 13 14 19 PARTS LIST OF CD MECHANISM UNIT Ref. No. 1 2 3 4 5 6 7 8 9 10 Part No.
DN-C635 41 PACKING VIEW 203 ~ 207 202 209 201 202 208 210 211 210 PARTS LIST OF PACKING & ACCESSORIES Note: The symbols in the column "Remarks" indicate the following destinations. E3: U.S.A./Canada model E2K: Korea model E2: Europe model JP: Japan model Ref.No. ★ Part No. Part Name Remarks Q'ty 201 00D 505 8092 007 LAMINATE ENVELOPE 1 202 00D 503 1001 507 CUSHION 2 203 00D 505 0038 030 POLY COVER 204 00D 515 0923 304 S.S.LIST COM.
DN-C635 NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 1. 2. 3. 4. CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
DN-C635 43 SCHEMATIC DIAGRAMS (1/3) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F ( ) G SIGNAL LINE SCHEMATIC DIAGRAMS (1/3) H GU-3510 MAIN UNIT(1/2) 43
DN-C635 44 SCHEMATIC DIAGRAMS (2/3) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F ( ) G SCHEMATIC DIAGRAMS (2/3) H GU-3510 MAIN UNIT(2/2) 44
DN-C635 45 SCHEMATIC DIAGRAMS (3/3) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (3/3) GU-3511-1 DISPLAY UNIT GU-3511-2 SLIDE VR. UNIT GU-3511-3 H/P UNIT GU-3511-4 P.
DN-C635 DOCUMENTS FOR WEEE Details of Recycle parts (DN-C635) ＊ You have to remove the parts that marked “WEEE Mark ◆ “ when the recycling processing. (Europe model only) WEEE Mark Ref. No. Part Name Material Q'ty 1 ◆ MAIN P.W.B. UNIT ASS'Y COMPLEX 2-1 ◆ FLT UNIT COMPLEX 1 1 2-2 ◆ SLIDE VR.
DN-C635 WEEE Mark Ref. No. Part Name Material Q'ty SCREWS 101 3X6 CBS-B STEEL 102 3X6 FHHS MFZNII-B STEEL 8 103 3X6 CBTS(S)-Z STEEL 17 104 4X8 CBTS (S)-Z STEEL 3 105 3X6 CBTS(S)-B STEEL 22 106 3X10 CBTS (P)-B STEEL 4 107 SPECIAL SCREW STEEL 2 108 SPECIAL SCREW STEEL 2 109 3W-B STEEL 6 110 FIXING SCREW STEEL 7 111 3P.
DN-C635 Exploded view of DN-C635 unit (Europe model) 108 15 You have to remove the parts that marked “WEEE Mark ◆ “ when the recycling processing.
DN-C635 49 Exploded view of CD Mechanism unit (CD11FT3NF) 2 1 3 4 4 3 20 A ◆ 17 3 16 8 16 7 11 B 2 6 12 C 1 10 5 15 9 18 ◆ 13 14 19 Details of Recycle parts for CD Mechanism unit ＊ You have to remove the parts that marked “WEEE Mark ◆ “ when the recycling processing. (Europe model only) Ref. No.
DN-C635 Details of Recycle parts for Power transformer (Ref. No. 9) 26 25 5 7 5 24 9 11 14 16 17 19 18 20 15 21 1 2 4 3 23 22 13 12 10 8 3 No. No.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 1 page of 39 Specification for Serial Interface DN-C635 Denon, Ltd.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 2 page of 39 Histories Rev. Date Name 1.0 Jan.,28,’03 J.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 3 page of 39 Contents 1 Serial communication interface ---------------------------------------------------------------------------- 4 1.1 Physical interface ------------------------------------------------------------------------------------------- 4 1.
Revision1.0 Date 2003-01-28 1 DN-C635 Serial Interface Specification 4 page of 39 Serial communication interface 1.1 Physical interface a) DN-C635 has pin Dsub female connector for serial interface. b) Table 1 indicates pin assignment of connector signals. RS-232C and RS-422A can be selected with software switch on DN-C635. Terminal # 1 2 3 4 5 6 7 8 9 RS-232C Signal NC TxD RxD NC S.GROUND NC NC NC NC I/O O I - RS-422A Signal NC TxDRxD NC S.GROUND NC TXD RXDNC I/O O I O I - Table 1.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 5 page of 39 1.
Revision1.0 Date 2003-01-28 2 DN-C635 Serial Interface Specification 6 page of 39 Command format and answer format The DN-C635 uses commands each of which consists of a data row (some commands no need PC) composed of command codes (CC) and parameter codes (PC). The host shall be designed to send block check characters (BCC) following ETX, with the data row enclosed in STX (text start: 0x02) and ETX (text termination: 0x03). The DN-C635 shall complete command receive with correct BCC codes.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 7 page of 39 2.1 Protocol for data transmission and reception This device’s serial protocol is based on half-duplex communication. Therefore the host shall transmit commands and receive answers according to the following procedure. Basic procedure 1) The host selects a prefer command and transmit codes to device. The host shall not send each byte within 40µsec because the device cannot receive within 40µsec after previous byte.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 8 page of 39 2.2 Command / Answer sequence Figure 3 is examples of command and answer sequence for DN-T645/625. DEVICE HOST STX Command Transmission CC PC0 PC1 PC2 Min 40µsec Max 40msec PCn ETX BCC Check BCC Max 5 sec. STX RC AC PC0 PC1 PCn ETX Check BCC BCC STX Next Command Transmission CC PC0 Figure 3.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 9 page of 39 2.3 List of command codes No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Command Code (ASCII) Destination Syste CD m 0x20(‘SP’) X 0x21(‘!’) X PLAY 0x30(‘0’) X Reset Sleep Request CD Status Request Firmware Rev.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 10 page of 39 2.4 List of answer codes No. 1 2 3 4 5 6 Status Command OK Invalid Format Error None track requested None time requested Condition Error Code (ASCII) Description 0x20(SP) Received the command correctly. 0x30(‘0’) Received invalid command or parameter. 0x31(‘1’) Received inappropriate format command. 0x32(‘2’) Requested track does not exit. 0x33 (‘3’) Requested time does not exit. 0x35 (‘5’) Condition error occurs. Table 3.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 11 page of 39 2.6 Command specification 2.6.1 RESET command This command resets the device. After RESET command the device will do some operations for reset and return Answer code. At last the device resets itself. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 STX( 0x02 ) Command code(‘SP’) Reserve( 0x00 ) Reserve( 0x00 ) Reserve( 0x00 ) Reserve( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 1 0 Table 5.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 12 page of 39 2.6.2 SLEEP command The SLEEP command forces the device to enter sleep mode. The device will stop all of operations, turns off displays and returns Answer code. To wake up, send Operation command (ex. Play, Pause, Stop…).
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 13 page of 39 2.6.3 REQUEST CD PLAY STATUS command Using this command, the host can get CD player information. The host shall send this command repeatedly to sense the CD player’s status.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 14 page of 39 Code 0x31(‘1’) 0x32(‘2’) 0x33(‘3’) 0x34(‘4’) 0x35(‘5’) 0x36(‘6’) 0x37(‘7’) Disc Type Reserved Reserved Reserved CD-DA MP3 UNKNOWN CD-Text Table 11. Disc type code Code 0x31(‘1’) 0x32(‘2’) 0x33(‘3’) Code 0x31(‘1’) 0x32(‘2’) 0x33(‘3’) 0x34(‘4’) 0x35(‘5’) 0x36(‘6’) Audio Format Reserved Reserved MPEG LPCM Reserved UNKNOWN Table 12. Audio format code Play mode Normal Program Random Table 14.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 15 page of 39 2.6.4 REQUEST FIRMWARE REVISION command This command requests the microprocessor firmware revision code. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 STX( 0x02 ) Command code (‘1’) Reserve( 0x00 ) Reserve( 0x00 ) Reserve( 0x00 ) Reserve( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 2 1 0 1 0 Table 17.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 16 page of 39 2.6.5 REQUEST ERROR CODE command With this command the host can get ERROR CODE from the device in case of something wrong.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 17 page of 39 2.6.6 REQUEST MACHINE ID command This command requests the machine ID.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 18 page of 39 2.6.7 REQUEST CD TOC command This command requests the device to send CD TOC data. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 STX( 0x02 ) Command code (‘7’) Reserve ( 0x00 ) Track number 100 digits (Table 36) Track number 10 digits (Table 36) Track number 1 digits (Table 36) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 Table 35.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 19 page of 39 2.6.8 REQUEST TEXT DATA command This command requests the device to send text data. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 STX( 0x02 ) Command code (‘8’) Data Type (Table 39) Track number 100 digits (Table 40) Track number 10 digits (Table 40) Track number 1 digits (Table 40) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 Table 38.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 20 page of 39 2) Answer format byte/bit 0 1 2 3 4 5 6 7-36 37 38 39 7 6 5 4 3 2 STX( 0x02 ) Reply code (‘8’) Answer code (Table 3) Data Type (Table 39) Track number 100 digits (Table 40) Track number 10 digits (Table 40) Track number 1 digits (Table 40) Text Data ( 30charactors ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) Table 41. Request Text Data answer 3) Special conditions None.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 21 page of 39 2.6.9 Request Display Status command This command acquires the display condition of the display. 1) Command format Byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 STX( 0x02 ) Command code (‘9’) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 2 1 0 Table 42.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 22 page of 39 2.6.10 Request Program Table command This command acquires 10 occurrences of information that is registered to program with unit. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 STX( 0x02 ) Command code (‘;’) Program Table Num (‘0’ – ‘9’) (Table 47) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 0 Table 46.
Revision1.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 24 page of 39 2.6.11 PLAY command 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 STX( 0x02 ) Command code (‘@’) Mechanism select ( CD : ‘0’) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 1 0 Table 49.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 25 page of 39 2.6.12 STOP command This command stops playback. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 STX( 0x02 ) Command code (‘A’) Mechanism select ( CD : ‘0’) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 1 0 Table 51.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 26 page of 39 2.6.13 CD PAUSE command This command pause the CD. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 STX( 0x02 ) Command code (‘B’) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 2 1 0 4 3 2 STX( 0x02 ) Reply code (‘B’) Answer code (Table 3) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 Table 53.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 27 page of 39 2.6.14 Skip command This command does the music search of the CD. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 STX( 0x02 ) Command code (‘C’) Skip code (Forward : ’+’, Reverse : ’-‘) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 1 0 Table 55.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 28 page of 39 2.6.15 SEARCH command This command does the music search at designated speed in the CD playback. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 STX( 0x02 ) Command code (‘D’) Search Speed (Table 58) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 1 0 Table 57.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 29 page of 39 2.6.16 Open / Close Command This command opens and closes the loader of the CD. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 STX( 0x02 ) Command code (‘E’) Open / Close Code(Close : ‘0’, Open : ‘1’) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 0 Table 60.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 30 page of 39 2.6.17 Cue command This command transfers playback position in the queue point and Pause.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 31 page of 39 2.6.18 Program / Direct command This command Selects a program mode or a direct mode. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 STX( 0x02 ) Command code (‘G’) Program / Direct Code (Direct : ‘0’, Program : ‘1’, Program input : ‘2’, Program input end: ‘3’) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) Table 64.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 32 page of 39 2.6.19 Track Num Entry command This command designates the truck that should program playback truck, in the case of program mode in the case of a direct mode. 1) Command format Byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 STX( 0x02 ) Command code (‘H’) Reserve ( 0x00 ) Track number 100 digits Track number 10 digits Track number 1 digits ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 1 0 Table 66.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 33 page of 39 2.6.20 A-B command This command designates A point, B point in an A-B point designated repeating function 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 STX( 0x02 ) Command code (‘L’) A-B Code(A-B OFF : ‘0’, A-set : ‘1’, B-Set : ‘2’) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 0 Table 75.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 34 page of 39 2.6.21 Pitch command This command does pitch function On/off. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 STX( 0x02 ) Command code (‘N’) Pitch code (OFF : ‘0’, ON : ‘1’) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 1 0 Table 79.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 35 page of 39 2.6.22 Pitch Set command This command sets up the numerical value of pitch function. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 STX( 0x02 ) Command code (‘O’) Pitch symbol (‘+’,’-‘) Pitch 10 digits Pitch 1 digits Pitch 0.1 digits ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 2 1 0 4 3 2 STX( 0x02 ) Reply code (‘O’) Answer code (table 3) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 Table 81.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 36 page of 39 2.6.23 Time command This command changes Elapse/Remain/Total Remain time display. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 1 0 STX( 0x02 ) Command code (‘P’) Time Mode Code(Elapsed : ‘0’, Remain : ‘1’, Total Remain : ‘2’) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) Table 83.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 37 page of 39 2.6.24 Title command This command changes display. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 STX( 0x02 ) Command code (‘Q’) Title code(Table 86) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 2 1 0 4 3 2 STX( 0x02 ) Reply code (‘Q’) Answer code (Table 3) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 Table 85.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 38 page of 39 2.6.25 Repeat command This command changes repeating function. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 STX( 0x02 ) Command code (‘R’) Repeat Code(OFF : ‘0’, ON : ‘1’) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 1 0 Table 88.
Revision1.0 Date 2003-01-28 DN-C635 Serial Interface Specification 39 page of 39 2.6.26 Play Mode command This command changes playback function. 1) Command format byte/bit 0 1 2 3 4 5 6 7 8 7 6 5 4 3 2 STX( 0x02 ) Command code (‘S’) Play Mode Code (Table 91) Reserve ( 0x00 ) Reserve ( 0x00 ) Reserve ( 0x00 ) ETX( 0x03 ) BCCH( high-level ) BCCL( low-level ) 1 0 1 0 Table 90. Play Mode command CODE Play Mode Code 0x30 (‘0’) Single 0x31 (‘1’) Continue Table 91.
