For Japan model SERVICE MANUAL MODEL Ver. 1 DCD-SA100 SUPER AUDIO CD PLAYER 注 意 サービスをおこなう前に、このサービスマニュアルを 必ずお読みください。本機は、火災、感電、けがなど に対する安全性を確保するために、さまざまな配慮を おこなっており、また法的には「電気用品安全法」に もとづき、所定の許可を得て製造されております。 従ってサービスをおこなう際は、これらの安全性が維 持されるよう、このサービスマニュアルに記載されて いる注意事項を必ずお守りください。 本機の仕様は性能改良のため、予告なく変更すること があります。 ● 補修用性能部品の保有期間は、製造打切後8年です。 ● For purposes of improvement, specifications and design are subject to change without notice.
DCD-SA100 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
DCD-SA100 3 レーザーピックアップ取扱い上の注意と交換 1. 分解 /Disassembly 本メカニズムは、専門工場で、精密に組立て調整しております。安易に分解、調整を行わないで下さい。 Do not disassemble or adjust this mechanism due to precision component. 2. 保管 /Storage 高温、あるいは高湿度下での保管は避けて下さい。静電気、塵埃対策を行い異常な外力が加わらないように保管して下さ い。 Do not leave this mechanism in high temperature and humidity. Be sure to prevent this mechanism from static electricity, dust and excessive forces. 放置する場合は、必ず静電袋に入れて塵埃を避けて下さい。 Do not leave this mechanism without a unti-static cover for the dust. 3.
DCD-SA100 4 対物レンズ、アクチュエータ、レーザーダイオード、光検出器、及び半固定抵抗には絶対に触れいで下さい。 Never touch the objective lens, actuator, laser diode, photo detector and the trim-potentiometer. 対物レンズに、塵埃や汚れが付かないように充分注意して下さい。 Be sure no dust or soil on the objective lens. 対物レンズに埃が付いた場合、きれいな空気を吹き付けて取り去って下さい。 If dust is on the objective lens, below it away by clean air.
DCD-SA100 5 DIAGNOSTICS OF OPTICAL PICKUP 光ピックアップの故障診断とトラバース AND REPLACING TRAVERSE UNIT ユニットの交換 Make failure diagnostics of the Optical Pickup as follows. If the laser drive current (Iop) becomes more than 1.5 times of the initial value, the Optical Pickup should be replaced. The laser drive current is registered on the seal attached to the rear of the Mecha.Unit. In case of replacing the Pickup, change the whole part of the Traverse Unit. No mechanical adjustment is necessary after the replacement.
DCD-SA100 1. Label Indication of SACD Mechanism. DVD CD 6 1. SACD メカのラベル表示 mA mA メカ背面のレーザー電流初期値 2. Note for Handling the Laser Pick-Up 2. レーザーピックアップの取扱注意 the protection for the damage of laser diode. If you want to change the optical device unit from any other units, you must keep the following. (1) It should be done at the desk already took measures the static electricity in care of removing the OPU's (Optical device unit) connector cable. (2) Workers should be put on the "Earth Band".
DCD-SA100 4.1. DVD Laser current measurement 7 4.1. DVD レーザー電流測定 LD(DVD) LD(DVD) +5V-A2 +5V-A2 Oscilloscope Oscilloscope (1) Connect the oscilloscope to +5V-M2 of test point for GND side and LD(DVD) of test point for signal side. (2) Playback the multilayer track 1 of the SACD Test Disc. (3) Measure the voltage between +5V-M2 and LD(DVD), calculate Iop by the formula as shown below.
DCD-SA100 8 トラバースユニットの交換方法 1. トラバースユニット交換準備 (1) クランプベースダンパーのはずしかた クランプベースダンパー (a) 2.
DCD-SA100 9 4. 組立 (1) (1) ピックアップのショートはずし ピックアップの 24P-FFC を基板へ接続後、2ヶ所の ショートをはずします。 クランプベース (2) クランプベースの仮置き レーザーから目を保護する為、クランプベースを仮置 きします。 (3) トラバースユニットをアップする。 SACD モジュール基板の接続ワイヤー (a) CY082 : 電源用の 8P-PH ワイヤー接続 (b) CX052 : ローディング用の電源 (1) ワイヤー接続 (c) CX053 : ローディング用の電源 (2) ワイヤー接続 (d) CX151 : スピンドル用 15P-FFC 接続 (e) CY251 : データ転送用 25P-FFC 接続 (f) CY252 : データ転送用 25P-FFC 接続 5.
DCD-SA100 7.
DCD-SA100 CD テストモード & サービスモード OPEN/CLOSE+PLAY+AC_ON モデル名表示 (DCD-SA100) H.R.NORMAL動作 TOCﾘｰﾄﾞ→ﾃﾞｨｽｸ全 曲再生→OPEN→ CLOSE→TOCﾘｰﾄﾞ を繰り返す。 又は B/Eマイコン Ver.表示 H.R.NORMAL表示 + H.R.SHORT動作 TOCﾘｰﾄﾞ→ﾃﾞｨｽｸ最 終曲再生→OPEN→ CLOSE→TOCﾘｰﾄﾞ を繰り返す。 + + H.R.SHORT表示 + テストモード + H.R.CHACKING動作 TOCﾘｰﾄﾞ→OPEN→ CLOSE→TOCﾘｰﾄﾞ を繰り返す。 F/Eマイコン Ver.表示 H.R.
DCD-SA100 SETTING UP THE TEST MODE テストモード (1) Setting up • In order to set up the test mode, you press STOP button and REV button simultaneously in the heat-run mode.Fundamentaly, you can set up the test mode at the stop state after disc loading. (Heat-run mode is set up by pressing PLAY button,holding OPEN/CLOSE button. If it becomes heat run mode, PLAY indicator and PAUSE indicator will light up.
DCD-SA100 (b) In the case of trace mode (error rate display) (refer to table 2 trace mode details) 13 (b) トレースモード ( エラーレート表示 ) の場合（ 表 2 ト レースモード詳細 参照） FL display (The display part of 13 digits) FL 管の表示 (13 桁の表示部 ) 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 Ｔ Ｙ Ｙ Ｆ Ｆ Ｆ Ｆ Ｆ Ｆ Ｆ Ｆ Ｆ Ｆ Ｔ Ｙ Ｙ Ｆ Ｆ Ｆ Ｆ Ｆ Ｆ Ｆ Ｆ Ｆ Ｆ (YY: select mode [71--94] ,F: address and an error rate display F at the time of undecided) (ＹＹ: 選択モード [71 ∼ 94]、Ｆ: アドレス及びエラーレート
DCD-SA100 (7) Test mode detailed table (7) テストモード詳細一覧表 Table 1: servo adjustment value display mode details ＸＸ Contents Contents suppleme nt 31 RFP FE Offset 32 RFP TE Gain 表 1 サーボ調整値表示モード詳細 Contents explanation ＸＸ 内容 内容補足 内容説明 layer 0 PI of CXD1881AR An offset value and FE An offset value is displayed. Pi offset is shown in higher rank 1Byte. FE offset is shown in low rank 1Byte.
DCD-SA100 15 48 Fcs AGC layer 1 The inside focus gain (setting 0x2000 to 1) value of CXD1885Q is displayed. Therefore, 0x1FF2 and in the case of 0x2012, it is as follows. 0x1FF2(8178) / 0x2000(8192) = 0.998291015625(fold) 0x2012(8210) / 0x2000(8192) = 1.002197265625(fold) Notes: The inside of ( ) is a decimal system equivalent. 48 Fcs AGC レイヤ 1 CXD1885Q 内 部フォ ーカス ゲイン (0x2000 を 1 として ) 値を表示。 0x1FF2 や 0x2012 の場合、以下のよ うになる。 0x1FF2(8178) / 0x2000(8192) = 0.
DCD-SA100 Table 2: trace mode details ＹＹ Contents 表 2 トレースモード詳細 Contents supplement ＹＹ 内容 補足説明 1 層内周の PO 誤り検出数とアド レスの表示 CD 時は無効。 71 A display of PO error detection number of the inner circumference of 1-layer and an address. It is invalid at the time of CD operation. 71 72 A display of PO uncorrectable number of the inner circumference of 1-layer and an address. It is invalid at the time of CD operation.
DCD-SA100 Table 3:Disc distinction information Mirr Count No Disc Mirr Width 17 表３ ディスク判別情報 FZC Count Except 2 and 3 - - CD High reflection 2 More than 0x8ED - CD Low reflection 2 More than 0x8ED DVD High reflection 2 DVDLow reflection Mirr Count PI Level No Disc - Mirr Width FZC Count PI Level 2 と 3 以外 - - - 2 0x8ED 以上 - 0x99 以上 CD 高反射 More than 0x99 CD 低反射 2 0x8ED 以上 - 0x98 以下 - Less than 0x98 DVD 高反射 2 0x8ED 以下 1 0x81 以上 DVD 低反射 2 0x8ED 以下 1 0x80 以下 Less t
DCD-SA100 18 ブロックダイヤグラム FGSA100 16M SD-RAM FRONT END SACD DECODER PROSESSOR [CXD2753] CD 16M D-RAM SPDIF RF AMP [CXD1881AR] MECHA UNIT [TD-5HPC] AL24 DXP7001 SEL FILTER AMP [CXD1885Q] ACT.DRIVER [FAN8042] DAC FILTER AMP SEL SP.
DCD-SA100 19 SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. 主な半導体を記載しています。汎用の半導体は記載を省略しています。 1. IC’s Note: Abbreviation ahead of IC No. indicates the name of P.W.B., etc. 注 ): IC No. の前の記号は、基板の名称を表します。 CS: CD/SACD P.W.B. PD: Power/Display P.W.B. SM: SACD module P.W.B.
DCD-SA100 20 Block Diagram 16/4M DRAM BCA HFD Data Slicer HF ECC Core Memory manager DVD Demodulation EDC MPEG I/F ASP VSTEM Serial I/F ASP Serial I/F PWM ATC CD-ROM Header Dec. TC Mecha control Servo singnal GIO Direction ROM/RAM A/D ICU Data RAM Terminal Name MCU I/F MCU ICU Servo control X'tal D/A PWM Timer Functions Audio CMD/ RSP reg. DSP VSTEM DSP CLK/Mode Audio I/F JTAG No. Serial Command Spindle TZC Video CD-DSP (DDCD) Data-PLL Peri.
DCD-SA100 No. Terminal Name I/O A/D 31 SYSCK O D Clock Classification Clock Monitor output. Function VDD & GND Digital 1.8V Power. (Internal logic system power) PU 21 PD SMT 32 DVDD18 P 33 XI I D Clock Crystal oscillation input. 34 XO O D Clock Crystal oscillation output. 35 DVSS P VDD & GND Digital Ground. 36 VDT7 O D VSTEM A/V MPEG data output 7. 37 VTD6 O D VSTEM A/V MPEG data output 6. 38 DVSS P VDD & GND Digital Ground.
DCD-SA100 No. 92 Terminal Name AD1 I/O A/D I A ADC Classification Function A ADC AD2 Input. VDD & GND Analog 3.3V Power. PU 22 PD SMT AD1 Input. 93 AD2 I 94 AVDD33 P 95 AD3 I A ADC AD3 Input. 96 AD4 I A ADC AD4 Input. 97 AD5 I A ADC AD5 Input. 98 AD6 I A ADC AD6 Input. 99 AD7 I A ADC AD7 Input. 100 AD8 I A ADC AD8 Input. 101 AD9 I A ADC AD9 Input. 102 VREFH I/O A ADC Max Reference Voltage input for ADC.
DCD-SA100 No. Terminal Name I/O A/D 151 RD13 I/O D Classification 152 RD12 I/O D DRAM I/F DRAM data input/output terminal 12. * 153 RD11 I/O D DRAM I/F DRAM data input/output terminal 11. * 154 RD10 I/O D DRAM I/F DRAM data input/output terminal 10. * 155 RD9 I/O D DRAM I/F DRAM data input/output terminal 9. * DRAM I/F Function DRAM data input/output terminal 13. 156 DVDD18 P VDD & GND Digital 1.8V Power.
DCD-SA100 CXD2753R (SM: IC401) Pin Assignment Block Diagram 24 24
DCD-SA100 Terminal Functions Pin Name I/O Functions 1 VSC - It fixed to ground.( for Core) 2 XMSLAT I Latch input for µCOM serial communication. 3 MSCK I Shift clock input for µCOM serial communication. 4 MSDATI I Data input for µCOM serial communication. 5 VDC - +2.5V Power for Core. 6 MSDATO O Data output for µCOM serial communication. “Hi-Z” potential except the output mode. 7 MSREADY O Completion flag of output preparation for µCOM serial communication.
DCD-SA100 Pin Name I/O Functions 51 TESTI I Input for TEST. It fixed to “L” potential. 52 53 TESTI I Input for TEST. It fixed to “L” potential. TESTO O Output for TEST. (open) 54 VDC - +2.5V Power for CORE. 55 DSADML O DSD Data output terminal for Lch Down Mix. 56 DSADMR O DSD Data output terminal for Rch Down Mix. 57 BCKASL I I/O selection terminal of the Bit clock for DSD data output. L=input (Slave), H=output (Master) 58 VSDSD - Ground terminal for DSD data output.
DCD-SA100 Pin Name 97 I/O Functions TESTI Ipu TEST input terminal. It fixed to “H” potential. 98 TESTO O TEST output terminal. (open) 99 VDC - +2.5V Power for CORE. 100 TESTI I TEST input terminal. It fixed to “L” potential. 101 TESTI I TEST input terminal. It fixed to “L” potential. 102 TESTI I TEST input terminal. It fixed to “L” potential. 103 TESTI I TEST input terminal. It fixed to “L” potential. 104 TESTI I TEST input terminal. It fixed to “L” potential.
DCD-SA100 Pin Name 149 A10 I/O Functions O Address output terminal for SDRAM. 150 VSC - Ground for CORE. 151 A9 O Address output terminal for SDRAM. 152 A8 O Address output terminal for SDRAM. 153 VDC - +2.5V Power for CORE. 154 A7 O Address output terminal for SDRAM. 155 A6 O Address output terminal for SDRAM. 156 A5 O Address output terminal for SDRAM. 157 A4 O Address output terminal for SDRAM. 158 VSIO - Ground for I/O.
DCD-SA100 M30624FGNGP (SM: IC731) Pin Assignment 29 29
DCD-SA100 30 M30624FGNGP Port Assignment Pin Port Function I/O Initial Mode Action Note 備考 (USER1:Ｈ/USER2:Ｈ) 1 P94/DA1/TB4IN P94 O H MULT_LED MULTI SURROUND(LED L=ON) 2 P93/DA0/TB3IN P93 O 3 P92/TB2IN/SOUT3 SOUT3 O H DSCS1 CHIP SELECT for FRONT DAC H DSDO CONTOROL SERIAL DATA for ALL DAC DCD1792/DXP7001 の control data 4 P91/TB1IN/SIN3 P91 I USER1 MODEL SELECT 1 Ｈ 5 P90/TB0IN/CLK3 CLK3 O DSCLK DATA CLOCK for ALL DAC DSD1792/DXP7001 の control data clock 6 BYTE
DCD-SA100 Pin Port Function I/O Initial Mode Action Note 38 P56/ALE P56 I OPEN1 OPEN(anytime) Flash(w: pull up) 39 P55/HOLD~ P55 I P_UP2 10K PULL UP(NON CONECT) Flash(w: GND) 40 P54/HLDA~ P54 - OPEN2 OPEN 41 P53/BCLK P53 - OPEN3 OPEN 42 P52/RD~ RD~ O MRD READ STROBE for XD1885Q 43 P51/WRH~/BHE~ P51 - OPEN4 OPEN 44 P50/WRL~/WR~ WR~ O MWR WRITE STROBE for XD1885Q 45 P47/CS3~ CS3~ O H MCS CHIP SELECT for CXD1885Q 46 P46/CS2~ CS2~ O H MCS2 CHIP SE
DCD-SA100 Pin Port Function I/O Initial Mode Action Note 32 備考 83 P03/D3 D3 I/O D3 8bit DATA LINE 84 P02/D2 D2 I/O D2 8bit DATA LINE 85 P01/D1 D1 I/O D1 8bit DATA LINE 86 P00/D0 D0 I/O D0 8bit DATA LINE 87 P107/AN7/KI3~ P107 O H MODE CD/SACD SWITCHING SIGNAL(L:CD,SACD:H) SACD と CD の digital audio data の切り換えを する。(L=CD, H=SACD) 一旦確定したら、次の DISC の認知までホールド する。 88 P106/AN6/KI2~ P106 O L FCS DISPLAY CHIP SERECT for FL DRIVER ML9207-01GP chip select 89 P105/AN5/KI1
DCD-SA100 ML9207-01 (PD: IC604) 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 AD2 AD1 VDISP2 NC VFL2 P4 P3 P2 P1 VDD DA CP CS RESET OSC1 OSC0 GND VFL1 COM24 COM23 ML9207-01 (PD: IC101) 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34 SEG35 VDISP1 COM1 COM2 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 AD3 AD4 SEG1 S
DCD-SA100 SDEN SDATA SCLK V33 LCP LCN MNTR CE FE TE PI V25 V125 TPH DFT LINK CXD1881AR (SM: IC501) 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 RX 49 32 MEVO MEV 50 31 MIN VNA 51 30 MLPF FNN 52 29 MB FNP 53 28 MP DIP 54 27 MIRR DIN 55 26 LDON 25 VNB 24 CDPD VPA 58 23 DVDPD AIP 59 22 COLD AIN 60 21 DVDLD ATON 61 20 VC ATOP 62 19 VPB RFSIN 63 18 CD_E RFDC 64 17 CD_F BYP 56 CXD1881AR 1 2 3 4 5 6 7 8 9 10 11 12 13
DCD-SA100 RFAC 59 DIP AIP 60 DIN AIN 61 FNN ATON 62 FNP ATOP Block Diagram 53 52 55 54 57 FCCR b7-0 FBCR b6-0 CGR b1 OUTPUT INHIBIT AGC DVDRFP 1 DVDRFN 2 MUX 4 RFSIN 63 SIGR b3 INPUT SEL RFCR b5-4 INPUT IMP SEL SSOUT RFCR b7-6 INPUT IMP SEL 56 BYP AGCO W/LPF GCA B W/LPF GCA C W/LPF GCA D W/LPF GCA SIGR b2-0 12dB is added @ high gain mode (CDR b5=1) GCA CD_A 16 B 11 CD_B 15 MUX C 10 2 CAR b3-2 SIGDET B+D A 49 RX Clamp & Env 2 CAR b1-0 Env/Clamp TENV A 12 AGC CHA
DCD-SA100 Terminal Function Power Supply Pins Name I/O Function VPA - Power for RF and serial port VPB - Power for servo VNA - GND for RF and serial port VNB - GND for servo V33 - Power for output buffer V25 - Reference Power for servo output Input Pins Name I/O Function DVDRFP,DVDRFN I RF signal input RFSIN I RF signal input AIP,AIN I AGC amp.
DCD-SA100 Analog Pins Name I/O Function BYP - RF AGC integration capacitor connecting terminal CP - Differential phase tracking LPF terminal CN - Differential phase tracking LPF terminal LCP - Lens shift offset cancel LPF terminal LCN - Lens shift offset cancel LPF terminal MP - MIRR top hold terminal MB - MIRR bottom hold terminal MEV - RFDC bottom envelope terminal MLPF - Mirror LPF terminal TPH - PI top hold terminal VC - Reference voltage output V125 - Reference vol
DCD-SA100 29 A6 28 A5 27 A4 26 VSS A2 23 VDD 25 A3 24 30 A7 37 N.C/RFU A1 22 38 VDDQ LDQM 14 31 A8 39 DQ8 VDDQ 13 A0 21 40 DQ9 A10/AP 20 41 VSSQ DQ6 11 DQ7 12 33 N.
DCD-SA100 FAN8042 (SM: IC508) 42 41 40 39 PVCC1 43 PS 44 OPOUT2 VREF 45 OPIN2- SVCC 46 OPIN2+ OPOUT1 47 GND OPIN1- 48 GND OPIN1+ Pin Assignments 38 37 IN1+ 1 36 DO1+ IN1- 2 35 DO1- OUT1 3 34 DO2+ IN2+ 4 33 DO2- IN2- 5 32 DO3+ GND 6 31 GND GND 7 30 GND OUT2 8 29 DO3- IN3+ 9 28 DO4+ IN3- 10 27 DO4- OUT3 11 26 DO5+ 12 25 DO5- 39 OUT4 CTL FWD REV GND 19 20 21 22 23 24 PVCC2 18 TSD-M 17 MUTE4 16 MUTE123 15 SGND 14 GND
DCD-SA100 Pin Definitions Pin Number Pin Name I/O Pin Function Description 1 IN1+ I CH1 op-amp input (+) 2 IN1- I CH1 op-amp input (-) 3 OUT1 O CH1 op-amp output 4 IN2+ I CH2 op-amp input (+) 5 IN2- I CH2 op-amp input (-) 6 GND - Ground 7 GND - Ground 8 OUT2 O CH2 op-amp output 9 IN3+ I CH3 op-amp input (+) 10 IN3- I CH3 op-amp input (-) CH3 op-amp output 11 OUT3 O 12 IN4+ I CH4 op-amp input (+) 13 IN4- I CH4 op-amp input (-) 14 OUT4 O CH4 op-amp out
DCD-SA100 Block Diagram SVCC OPIN1OPIN1+ OPOUT1 VREF GND 48 47 46 45 44 43 GND 42 OPOUT2 OPIN2+ OPIN2PS 41 40 39 38 POWER SAVE IN1+ 1 10K OUT1 3 10 K 10 K IN2+ 4 35 DO1- 40K 40K 40K 10K 10 K 10K 33 DO2- 40K 40K 32 DO3+ 5 40K GND 34 DO2+ 10K 40K IN2- 36 DO1+ 40 K 2 IN1- PVCC1 37 10 K 10K 40K 6 10 K 10 K 31 GND 40K 40K 10K 40K GND 7 30 GND 40K OUT2 8 10 K IN3+ 9 10 K 10 K IN3- 10 10 K 29 DO340K 40K 28 DO4+ 27 DO4- 40K OUT3 11 S M S C W + D - D 26 DO5+ IN4+ 1
DCD-SA100 42 DXP7001AF (CS: IC205) 23 33 34 22 44 12 1 11 DXP7001AF Terminal Function Pin No. Pin Name I/O Pin No.
DCD-SA100 43 M11L16161SA (SM: IC503) Vcc I/O0 I/O1 I/O2 I/O3 Vcc I/O4 I/O5 I/O6 I/O7 NC 1 2 3 4 5 6 7 8 9 10 11 44 43 42 41 40 39 38 37 36 35 34 Vss I/O15 I/O14 I/O13 I/O12 Vss I/O11 I/O10 I/O9 I/O8 NC NC NC WE RAS NC NC A0 A1 A2 A3 Vcc 12 13 14 15 16 17 18 19 20 21 22 33 32 31 30 29 28 27 26 25 24 23 NC CASL CASH OE A9 A8 A7 A6 A5 A4 Vss PIN DESCRIPTIONS PIN NO.
DCD-SA100 44 AN8471SA (SM: IC505) 32 BC4 BC3 BC2 BC1 VPUMP VLP VM1 16 VDD 1 18 16 15 14 13 12 32 31 OSC FG 10 Booster Logic Circuit FG2 20 Pin No.
DCD-SA100 45 T14L1024N (SM: IC732) DSD1792DBR (CS: IC206, 207, 502, 503) 1 DSDL VCC2L 28 2 DSDR AGND3L 27 3 DBCK IOUTL– 26 4 PLRCK IOUTL+ 25 5 PDATA AGND2 24 6 PBCK VCC1 23 7 SCK VCOML 22 8 DGND VCOMR 21 9 VDD IREF 20 10 MS AGND1 19 11 MDI IOUTR– 18 12 MC IOUTR+ 17 13 MDO AGND3R 16 14 RST VCC2R 15 terminal functions T E R M INAL I/O NAME PIN DSDL 1 I/O DESCRIPTIONS L-channel audio data input for DSD and external DF modes‡ PCM mode zero flag
DCD-SA100 T E R M INAL I/O DESCRIPTIONS NAME PIN PBCK 6 I Bit clock input. Connected GND for DSD mode† SCK 7 I System clock input† DGND 8 - Digital ground VDD 9 - Digital power supply, +3.3 V MS 10 I/O Chip select for mode control‡ MDI 11 I Mode control data input† MC 12 I Mode control clock input† MDO 13 I/O RST 14 I Reset† VCC2R 15 - Analog power supply (R-channel DACFF), +5.
DCD-SA100 TC74VHC157FT (SM: IC736) TC74VHC74FT (SM: IC734) AT24C04 (SM: IC737) BD4928G (PD: IC601) A0 1 8 VCC A1 A2 2 3 7 6 WP SCL GND 4 5 SDA VOUT 1 VDD 2 5 N.C. GND 3 4 N.C. VDD 2 Pin Configurations Function Pin Name A0 - A2 1 VOUT Address lnputs Sedrial Data SDA SCL Sedrial Clock lnput Write Protect No Connect WP NC Vref 3 GND S-80843C (SM: IC733) 4 3 1 OUT 2 VDD 3 N.C. 4 VSS GND 2 1 2.
DCD-SA100 48 3. FL DISPLAY 17-ST-04GNK (PD: FL601) 1 66 COLOR ILLUMINATION Reddish Orange ----- Above pattern Green ------------------ Other part PIN CONNECTION 11111111 11 22 22 22 2 1234 5678 901234567 89 01 23 45 6 PPPP PPPPPPPPP CONNECTION F N N N P P P P P P P P P 1 1 1 1 1 1 1 1 1 1 2 2 2 - XPP1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 PIN NO. 5555555556666666 1234567890123456 111 CONNECTION 2 1 0 9 8 7 6 5 4 3 2 1 N N N F GGGG GGGG GG GG P P X + PIN NO.
DCD-SA100 49 PRINTED WIRING BOARDS 1U-3532 CD/SACD P.W.B.
DCD-SA100 FOIL SIDE 50 50
DCD-SA100 51 1U-3533 POWER/DISPLAY P.W.B.
DCD-SA100 FOIL SIDE 52 52
DCD-SA100 1U-3562 SACD MODULE P.W.B.
DCD-SA100 54 NOTE FOR PARTS LIST l Part indicated with the mark " " are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused. l When ordering of part, clearly indicate "1" and "I" (i) to avoid missupplying. l Ordering part without stating its part number can not be supplied. l Part indicated with the mark " " is not illustrated in the exploded view. l Not including Carbon Film Resister ±5%, 1/4W Type in the P.W.Board parts list.
DCD-SA100 55 PARTS LIST OF P.W.B. UNIT ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります 1U-3532 CD/SACD P.W.B. UNIT ASS'Y Ref. No. Part No.
DCD-SA100 Ref. No. Part No.
DCD-SA100 Ref. No. Part No.
DCD-SA100 Ref. No. Part No.
DCD-SA100 Ref. No. Part No. Part Name CX111 205 1091 024 CX131 205 0668 063 13P FFC CON.BASE CX231 205 1100 009 23P FFC BASE(P=1) CX251,252 205 1260 004 25P FFC BASE (9610SA CY031 205 0233 032 3P EH CONNECTOR BASE CY032 205 0343 032 3P CONN.BASE(KR-PH) CY051 205 0233 058 5P EH CONNECTOR BASE CY052 205 0343 058 5P CONN.
DCD-SA100 60 1U-3533 POWER/DISPLAY P.W.B. UNIT ASS'Y Ref. No. Part No.
DCD-SA100 Ref. No. Part No.
DCD-SA100 Ref. No. C859,860 ! Part No.
DCD-SA100 63 1U-3562 SACD MODULE P.W.B. UNIT ASS'Y Ref. No. Part No.
DCD-SA100 Ref. No. Part No.
DCD-SA100 Ref. No. Part No.
DCD-SA100 Ref. No. Part No.
DCD-SA100 Ref. No. Part No.
DCD-SA100 Ref. No. Part No. Part Name CX151 205 1224 901 15P FFC BASE(P=1.0)L CX241 205 1152 905 24P FFC BASE(FLZ-SM1 CY082 205 0863 981 8P PH CON.
DCD-SA100 69 EXPLODED VIEW 108 Parts List 印の部分は安全を維持するために重要 101 101 33 な部品です。従って交換時は必ず指定の 6 108 部品を使用して下さい。 108 54,55 108 104 104 39 15 61,62 58 56 57 101 35 56 14 57 34 106 1-2 101 63,64 2-1 30 109 101 101 5 101 18 4 108 20 12 50,51 11 101 59,60 13 36 101 101 1-1 50,51 50,51 101 101 19 3 32 107 17 1-3 37 21 52,53 105 101 2-3 2-4 101 107 103 29 107 25 28 103 50,51 7 29 31 24 2-2 26 27 8 101 101 23 9 10 101 102 22 69 101 102
DCD-SA100 70 PARTS LIST OF EXPLODED VIEW ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 Ref.No. Part No. 1 1U-3532 ! ★ ★ Q'ty New 1 FRONT AUDIO UNIT 1-2 SURROUND AUDIO UNIT 2 Remarks CD/SACD P.W.B UNIT 1-1 1-3 ! Part Name JUNCTION UNIT 1U-3533 POWER/DISPLAY UNIT 2-1 POWER UNIT 2-2 DISPLAY UNIT 2-3 LED UNIT 2-4 P.
DCD-SA100 Ref.No. Part No. Part Name Remarks 71 Q'ty New 57 - BUTYL TAPE(W50 T1) 長さ：80、B.TAPE に貼る 2 58 - BUTYL TAPE(W25 T1) 長さ：100、P.TRANS 下に貼る 1 59 - BUTYL TAPE(W25 T2) 長さ：100、M.BRACKET 上に貼る 2 60 - NITOFLON TAPE(W25 T0.08) 長さ：100、B.TAPE に貼る 2 61 - BUTYL TAPE(W50 T2) 長さ：260、T.C.DAMPER に貼る 1 62 - NITOFLON TAPE(W50 T0.08) 長さ：260、B.TAPE に貼る 1 63 - BUTYL TAPE(W50 T2) 長さ：100、R.PANEL に貼る 1 64 - NITOFLON TAPE(W50 T0.08) 長さ：100、B.
DCD-SA100 EXPLODED VIEW OF SACD MECHANISM Parts List 15 14 12 50 60 9 8 59 58 52 15 7 11 15 51 31 10 4 13 5 15 30 55 57 27 26 53 20 55 18 2 29 3 28 19 55 1 17 25 24 16 56 55 23 21 22 61 6 55 54 72 72
DCD-SA100 73 PARTS LIST OF SACD MECHANISM ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 Ref. No. Part No. Part Name Remarks Q'ty 1 411 1988 101 MECHA CHASSIS 1 2 431 0426 503 PLATE GEAR 1 3 9KA 2A40 3D GEAR BASE SUB ASS'Y 1 4 441 1952 109 GEAR BASE ASS'Y 1 5 9KM 01T1 32 LD MOTOR 1 6-1 9KA 85P0 05 DETECTOR SW P.W.B.
DCD-SA100 POINTS OF GREASING (1/2) MOLYKOTE EM-30L 0.1mg x 2 points MOLYKOTE EM-30L 0.1mg MOLYKOTE EM-30L 0.1mg x 3 points MOLYKOTE EM-30L 0.1mg x 4 points MOLYKOTE EM-30L 0.1mg x 4 points MOLYKOTE EM-30L 0.1mg x 3 points MOLYKOTE EM-30L 0.1mg MOLYKOTE EM-30L 0.1mg x 3 points MOLYKOTE EM-30L 0.
DCD-SA100 POINTS OF GREASING (2/2) MOLYKOTE EM-30L 0.1mg x 4 points HANARL FL777 0.1mg MOLYKOTE EM-30L 0.1mg MOLYKOTE EM-30L 0.1mg x 5 points MOLYKOTE EM-30L 0.3mg 40~50mm MOLYKOTE EM-30L 0.1mg HANARL FL777 0.1mg MOLYKOTE EM-30L 0.
DCD-SA100 76 PACKING VIEW 203 202 203 205 210 204 212 211 CUSHION(A),(B)貼り付け箇所 (CARTON CASE上面から見た図) 203 214 CUSHIONを仮置きした 状態でCUSHION(A),(B) を貼り付ける 213 FRONT側 PARTS LIST OF PACKING & ACCESSORIES ＊本表に記載されている部品は、補修用部品のため製品に使用している部品とは一部、形状、寸法などが異なる場合があります。 Ref.No. Part No. Remarks Q'ty New 202 505 0131 076 CABINET COVER 1 203 503 9275 209 CUSHION 2 * 204 501 2053 037 CARTON CASE 1 * 205 505 0038 030 POLY COVER 1 206 511 4069 000 INST.
DCD-SA100 各部の波形 1 16 4 15 5 8 2 3 7 6 12 11 9 10 1U-3562 SACD MODULE P.W.B. unit foil side 13 14 1U-3532 JUNCTION P.W.B.
DCD-SA100 1. PLAY (1) CD (2) SACD TCD-784 1 RFAC (3) SACD Hybrid DAC Test Disc (4) SACD 3 FE 3 FE 2 FSCON 2 FSCON 6 FOK 6 FOK 4 PI 4 PI GND ; 15 VC16 GND ; 15 VC16 GND ; 15 VC16 4. PLAY start 2.
DCD-SA100 5.
DCD-SA100 NOTE FOR SCHEMATIC DIAGRAM 80 配線図について WARNING: Parts marked with this symbol ! have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. ! 印の部品は安全を維持するために重要な部品です。 従って交換時は必ず指定の部品を使用してください。 注） CAUTION: (1) 指定なき抵抗値は Ω、ｋ は ｋΩ、M は MΩ を示す。 Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.
DCD-SA100 SCHEMATIC DIAGRAMS (1/7) 1 2 3 4 5 6 7 8 9 10 81 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (1/7) 1U-3532-1 FRONT AUDIO UNIT 1U-3532-3 JUNCTION UNIT H 81
DCD-SA100 SCHEMATIC DIAGRAMS (2/7) 1 2 3 4 5 6 7 8 9 10 82 11 A B C D E F G SIGNAL LINE SCHEMATIC DIAGRAMS (2/7) 1U-3532-2 SURROUND AUDIO UNIT H 82
DCD-SA100 SCHEMATIC DIAGRAMS (3/7) 1 2 3 4 5 6 7 8 9 10 83 11 A B C D E F G SCHEMATIC DIAGRAMS (3/7) 1U-3533-1 POWER UNIT H 83
DCD-SA100 SCHEMATIC DIAGRAMS (4/7) 1 2 3 4 5 6 7 8 9 10 84 11 A B C D E F G SCHEMATIC DIAGRAMS (4/7) 1U-3533-2 DISPLAY UNIT 1U-3533-3 LED UNIT 1U-3533-4 P.
DCD-SA100 SCHEMATIC DIAGRAMS (5/7) 1 2 3 4 5 6 7 8 9 10 85 11 to OPU A B CY251 C D E to Traverse Mecha.
DCD-SA100 SCHEMATIC DIAGRAMS (6/7) 2 3 4 5 6 7 8 9 10 11 A B CY252 1 86 C D E CX131 F G SIGNAL LINE SCHEMATIC DIAGRAMS (6/7) 1U-3562 SACD MODULE UNIT (2/3) H 86
DCD-SA100 SCHEMATIC DIAGRAMS (7/7) 1 2 3 4 5 6 7 8 9 10 87 11 A CX052 B to 1U-3532-3 Junction Unit C D 1U-3533-1 E to 1U-3532-1 Front Audio Unit F G SIGNAL LINE SCHEMATIC DIAGRAMS (7/7) 1U-3562 SACD MODULE UNIT (3/3) H 87
