For Hong Kong, U.S.A. and Canada model Hi-Fi Personal Audio System SERVICE MANUAL MODEL D-A03 PERSONAL AUDIO SYSTEM VERTICAL LOADING SYSTEM COMPACT DISC PLAYER VERTICAL LOADING SYSTEM COMPACT DISC PLAYER POWER POWER CD CD PERSONAL AUDIO SYSTEM/CD-MD RECEIVER SDB FM/AM D-A03 MD AUX MENU FM/AM AUX EQ TUNING VOLUME VOLUME TUNING/ PRESET SLEEP TIMER TUNING/ PRESET OFF TOTAL RANDOM INTOR SCAN ROCK POP JAZZ DANCE FLATT N.SPEED HI.
D-A03 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective. SPECIFICATIONS (There is no MD Section in the U.S.A.
D-A03 DISASSEMBLY (Follow the procedure below in reverse order when reassembling) 1. Rear Cover & Front Panel 1) Remove 14 rear screws 1 and 4 (E3: 2) bottom screws 2 on the Rear Cover. 2) Disconnect connectors and wire 3 ~ 7 on the Front Panel. The Rear Cover and Front Panel can be detached respectively. 1 1 2 1 4 5P Connector 6 11P Connector 7 1P Earth Lug 5 6P Connector 3 4P Connector 2. Main P.W.B. 8 1) Remove 5 screws 8 . 2) Disconnect 2 FFCs, 10 connectors on the Main P.W.B.
D-A03 9 3. MD Mecha. 1) Remove 3 screws 9 . 2) Disconnect 1 each FFC and connector on the Main P.W.B. Connector MD Mecha. FFC 4. CD Mecha. Chassis 1) Remove 4 each screws and from the front side to detach the CD Door Lens and CD Door Bracket. 2) Remove 6 screws and take off the Main Chassis. Main Chassis CD Door Bracket CD Door Lens 5. CD Mecha. 1) Remove 4 screws ! fixing the Bracket. 2) Detach the CD Mecha. upward as shown to the arrow direction.
D-A03 6. Speaker Box (L & R) Speaker Box (L) 1) Remove 4 screws " . 2) Disconnect 2 connectors. Speaker Box (R) " " 7. Tuner P.W.B. 1) Remove 2 screws # . Tuner P.W.B. # 8. Power P.W.B. 1) Remove 6 screws $ . 2) Disconnect 1 connector. Power P.W.B.
D-A03 ADJUSTMENT TUNER SECTION Connections and adjustment point AM SG Modulation frequency: 400Hz Modulation factor: 30% Modulation frequency: 1kHz L+R: 90% (67.5kHz Dev.) Pilot: 10% (7.5kHz Dev.) 75kHz Dev.
D-A03 CD SECTION 1. RF level Confieming Connection Oscilloscope CD Servo Micon PWB Probe RF0 V REF Oscilloscope V H 50mV/div + − 10:1 Step Check 1. Press CD Play/Pause ( 0.2µs/div or 0.5µs/div ) button to make it playback state. A 2. Check RF level with oscilloscope. 3. Confirm that the waveform is in good • Set input mode to ALTERNATE or CHOPPER. A=0.8~1.2V shape. ( eye pattern in center must be able to discriminate clearly.) Eye Pattern 2. Pickup Connection Step 1.
D-A03 BLOCK DIAGRAM 1 4 3 2 5 6 7 8 TACT KEY REMOTE Sensor A DISPLAY UNIT LCD 8com,60seg MAIN UNIT BACK light MICRO COMPUTER M38199 DSP TC94A14FA Door driver BA6286 Motor driver LA6558 CD DOOR CD MECHA CD4LXWNK RF AMP TA2157F LCD Controller LC75811W B Reset MD UNIT MDM08AD 74VHC08 ELE.VR SYSTEM LC75342M TUNER UNIT (Hong Kong Model) 4p Terminal P.W.B.
D-A03 TEST MODE (There is no MD Section in the U.S.A. and Canada model) From power off state to TEST mode To enter into the TEST mode, plug the AC cord to the wall outlet while pressing the CD PLAY (CD ) button and TUNER button simultaneously. The version information is displayed initially. Thereafter press the SKIP UP/DOWN button to select the TEST mode and then press the CD STOP button to determine it. Press the DIRECT key during version display to obtain the designated TEST mode directly. TEST MODE No.
D-A03 1. CD test Outline: Readout of the set value after automatic adjustment (for judging difference from initial value) Forced operation of pickup (Inner/Outer circumference feed) During the PLAY mode, the number of errors accumulated for 10 seconds (750 frames) is displayed. Basic CD operation by CD-PLAY button During the TEST mode, the display is turned on and the following buttons become effective. TNO Display N: Normal speed H: Double speed Time Display Operation 1.
D-A03 Double-speed mode Press the MD-REC button in the stop mode to switch to the double/constant-speed mode cyclically. During the double-speed mode, lights up. CD TEST STEP NO Display N:NORMAL SPEED TNO Display H:HIGH SPEED Time Display N H Lights when double-speed mode STEP NO Display TNO Display Time Display 1.STEP NO. : 0 when stopped 2.Time display: Blank from the stop mode to STEP 4 Coefficient name Coefficient Readout of coefficient 2. MD test mode (Refer to page 12 and after.
D-A03 MD SECTION Enter the test mode, adjust or set as shown in the following table according to the repair operations.
D-A03 Entering the specific mode Whenever the CD PLAY (CD ) button is pressed, the mode is changed. If the REC button is pressed instead, the mode will change in the opposite order.
D-A03 2. AUTO pre-adjustment mode (Low reflection disc only) Step No.
D-A03 5. EEPROM Setting Mode A) Focus Setting Step No.
D-A03 C) Tracking Setting Step No.
D-A03 D) Slide Setting Step No.
D-A03 G) Adjust Setting Step No.
D-A03 6. Test-play Mode (For checking playback performance at the address defined.) Step No.
D-A03 Lead-in SW Position Measurement Mode 1. Adjustment Load the high reflection test disc TGYS1. Note: Adjust the lead-in switch position to FF85 ~ FFD2. 1. Loosen 1 screw (A1) fixing the Mecha. SW P.W.B. 2. Loosen the screw once and retighten it with pushing the P.W.B. to the A direction if the lead-in switch position is less than FF85 before loosening the screw, or with pushing to the B direction if the position is more than FFD2.
D-A03 Detailed Description of Error Indication Error Indication Content of Error Remedy Can't REC DEFECT occured continuously for 10 times during REC-PLAY Record enable cluster become 0 due to DEFECT occurrence during REC-PLAY. Unable to read address. However repeating try, unable to enter REC mode in 20 seconds. Is there any scratch, dust, finger print, black spot, etc. on the disc? Check for eccentricity, warp, etc. of disc.
D-A03 Error Indication Content of Error Remedy Can't WRITE As abnormality occurred during UTOC rewriting, unable to perform correct rewriting. Scratch, etc. on the disc. Replace with the other disc. FOCUS ERROR Unable to lead in FOCUS as the disc is inserted. Is there any scratch, dust, finger print, black spot, etc. on the disc? Check for considerable eccentricity, warp etc. disc. BLANK MD As a result of reading UTOC, all TNO and NAME character number is 0.
D-A03 EEPROM WRITING PROCEDURE EEPROM (IC1402) writing procedure 1. Method for setting the reference temperature value (This setting should be performed quickly at a room temperature, between 21 to 29 when the PWB is not hot.) 1) When replacing the EEPROM, wait until it has cooled down. 2) Connect the main unit using the single MD main PWB. 3) Enter the test mode as shown on page 12. EJECT 4) Press the TUNER (BAND) button.
D-A03 Table of EEPROM Contents (Version: 01) (a) Focus Setting (c) Tracking Setting Item Setting Item Setting FG______$$ 9BH TG______$$ 49H FG2_____$$ B1H TG2_____$$ 6BH FF0_____$$ 10H TF0_____$$ 10H FF1_____$$ 70H TF1_____$$ 6BH FF2_____$$ E0H TF2_____$$ F0H FZHLEV__$$ EDH FT3_____$$ 08H FOKLEVh_$$ 07H SVCNT4__$$ 01H FOKLEVt_$$ 09H TRBLVo__$$ 62H FOSTn___$$ 2CH TRBLVt__$$ 4CH DSCJG__$$ 0DH TRKLVo__$$ 5BH TRKLVt__$$ 2BH TDPWo___$$ 67H TDPWt___$$ 21H SLCTo
D-A03 (d) Slide Setting (e) Control Setting (f) ADJSET Display Setting Display Setting SLG_____$$ 46H CONTRL1_$$ 08H COK___$$ 58H SL2_____$$ 10H CONTRL2_$$ 02H FAT___$$ C0H SLDLIM__$$ 7FH ADJTTM__$$ 14H TAT___$$ 3EH SLDLEV__$$ 14H HDEQAD__$$ 92H CAT___$$ 40H SLKLVk__$$ 60H LDEQAD__$$ 8EH FAB___$$ (64H) * SLKLVt__$$ 34H GDEQAD__$$ 91H STR___$$ 0BH SLKLVm__$$ 60H GDEQAD2_$$ 91H SFS___$$ 0DH SLBKm__$$ 08H HDEQBC__$$ 8CH STC___$$ 0DH SLKrio__$$ 64H LDEQB
CN1501 8 DSCK CN1501 12 DSTB Test mode command transmission period 13.6ms (Until CMD RCV received) CN1501 8 DSCK CN1501 12 DSTB IC1401 80 XRST 3.2ms IC1401 80 XRST CN1501 19 PCONTO CN1501 5 PDOWN CN1401 1 , 2 TRY+/TRY- 3.2ms Set the system microcomputer to "H" by this point (10ms) IC1401 12 RESET CN1401 1 , 2 TRY+/TRY- CN1501 19 PCONTO CN1501 5 PDOWN IC1401 12 RESET CN1501 6 RESET CN1501 6 RESET 30ms±2ms IC1401 15 MCCK 1.5ms TP1800 3.2V CN1501 7 MD-ST IC1401 15 MCCK TP1800 3.
D-A03 TROUBLESHOOTING OF CD CD SECTION When the CD does not function When the CD section does not operate when the objective lens of the optical pickup is dirty, this section may not operate. Clean the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check the following items. Remove the cabinet and follow the trouble shooting instructions.
D-A03 The laser does not light up Is 1.5V applied to the LDO terminal of pin 7 of IC146 ? No IC146 is defective Yes No Is +1.8V applied to the collector of TR101 ? Yes Is +3.3V applied to C109 of R108 ? No R108 is defective. Yes Check the +3.3V stabilization circuit of IC145 and L103. No Is +1.8V applied to pin 10 of CX151 ? Yes The optical pickup is defective if CX151 is normal. The PWB pattern has been cut between TR101 and pin 10 of CX151.
D-A03 The triangular wave for focus servo does not appears Is +3.3V applied to pin 6 of IC149 ? No The +3.3V line of IC149 is defective. Yes Does the triangular wave appear at pin 33 on IC149 ? No Check the parts around pin 33 on IC149. If OK, IC149 is defective. Yes Does the triangular wave appear at pin 13 on IC145 ? No The connection of signal lines between pin 33 on IC149 and pin 13 on IC145 is poor.
D-A03 No sound is heard Is the digital signal outputted from the pin 4 (digital OUT) of IC149 ? No Check the parts around IC149. If OK, IC149 is defective. Yes Is digital signal outputted from the pin 8 (digital OUT) of IC150 ? No Check the parts around IC150. If OK, IC150 is defective. Yes Is the digital signal sent to the pin 26 of CX281 ? No Check the CD/MD connection sections.
D-A03 WAVEFORMS OF CD CIRCUIT Tracking error Foucus servo on T CH2=2V DC 10:1 2000/09/18 15:29:21 CH3=2V DC 10:1 2ms/div (2ms/div) NORM:500kS/s IC146 15pin FEO Disc playback When there is no wound in the disc. 1 T Stopped CH1=500mV DC 10:1 2000/09/18 16:56:26 5ms/div (5ms/div) NORM:200kS/s Stopped CH1=200mV DC 10:1 3 When a door was closed, disc dovetail 1 IC145 4pin FO+ T 1 4 IC146 11pin TEO T 2 5 CH1 V/DIV CAL VAR =Offset= =Filter= 0.000V Smoothing : ON CH1 : BW : 20MHz CH2 : 0.
D-A03 Feed motor and tracking output during the track jump Stopped CH1=200mV DC 10:1 9 Normal track actuator drive 2000/09/18 17:12:20 100ms/div (100ms/div) NORM:10kS/s CH2=1V DC 10:1 Stopped CH1=1V DC 10:1 IC146 40pin FMO T 1 IC145 5pin TR+ 2 CH1 V/DIV VAR CAL =Offset= =Filter= 0.000V Smoothing : ON CH1 : BW : 20MHz CH2 : 0.00V CH3 : 0.00V CH4 : 0.00V CH1 V/DIV 200mV =Record Length= Main : 10K Zoom : 5K CH1 V/DIV VAR CAL =Offset= =Filter= 0.00V Smoothing : ON CH1 : BW : 20MHz CH2 : 0.
D-A03 TROUBLESHOOTING OF MD (Hong Kong model) When MD Inoperative Clean the object lens first then check the playback function because no operation may be caused by dirty object lens of the optical pickup. Follow the steps below if it's still inoperative after the cleaning. When the object lens is unclean with dust or etc., problems such as skipping or no TOC indication may happen. Check whether the lens is clean or not before adjustment, and clean as follows if it's dirty.
D-A03 Disc Loading Not Normal When disc insertion, does the loading operation start ? Yes No Is the voltage at 17, 18pin of CN1501 +5.0 ~ +6.0V ? No Check Power, System PWB, and CN1501. Yes When reset power on, does pulse signal enter into 6pin of CN1501 ? No Check System PWB and CN1501. Yes No Is the voltage at 62pin of IC1401 +3.2V ? Check around Q1804 and IC1401. Yes Does pulse signal 8.4672MHz add to 15pin of IC1401 ? Yes No Check IC1201.
D-A03 Recording/playback Operation Set to Rec/play Test Mode after confirming audio output at playback with low ref. disc insertion. No No recording from the start address. Isn't the disc set to record prohibited position ? Yes Is there RF waveform at TP1201 or 1pin of IC1201(Mecha.) when playback after recording ? Yes No Is there any level change between recording and playback at 3, 26, 39pin of IC1401? No Check IC1401 peripherals. Yes No Is there RF waveform at 50pin of IC1201(Mecha.
D-A03 WAVEFORMS OF MD CIRCUIT (Hong Kong model) 36
D-A03 37
D-A03 SEMICONDUCTORS IC’s M38199 (IC601) E1H (1~600) M38199MP-276 (262 2963 206) E3, E1H (600~) M38199MP-285 (262 2963 303) 100 81 1 80 TOP VIEW 51 30 31 50 M38199 Terminal Function Pin No.
D-A03 Pin No.
D-A03 33 FOO 34 TRO 35 VREF 36 RFGC 37 TEBC 38 SEL 39 AVDD3 40 FMO 41 DMO 42 VSS3 43 VDD3 44 TESIN 45 XVSS3 46 XI 47 XO 48 XVDD3 TC94A14FA (IC149) DVSS3 49 32 TEZI Clock generator RO 50 + - PWM 31 TEI D/A 30 SBAD DVDD3 51 LPF DVR 52 1-bit DAC 29 FEI + - A/D Servo control 28 RFRP LO 53 DVSS3 54 27 RFZI + - ZDET 55 Correction circuit VSS5 56 BUS0 57 BUS1 58 16k RAM Synchronous guarantee EFM decoder BUS3 60 Audio out circuit 24 RFI 23 SLCO 22 AVSS3 VCO 21 VCOF Digit
D-A03 Pin No.
D-A03 LA6558 (IC145) X2 VO4- 5 VO4+ 6 Level Shift VO5+ 4 28 VO2+ Level Shift VO5- 3 29 VO6- Level Shift VO3+ 2 30 VO6+ X2 Level Shift X2 Level Shift Level Shift X2 VO3- 1 26 VO1+ 27 VO2- 25 VO1Power System GND P-GND1 7 Power System GND + - S-GND 8 23 P-VCC(IN) Signal System GND VREF 9 IN-MUTE 10 0-RESET 11 3.3VREG Signal System VCC MUTE RESET 200 + 200 VIN5 13 Power System VCC Reference Voltage RESET OUTPUT L with VREF at 0.
D-A03 TA2157F (IC146) 1 3kΩ + - TNI 15pF 240kΩ + - X2 X0.5 k 5 + - + - + - X2 X0.5 1 4 22 RFO 180kΩ 60kΩ 94kΩ TPI 180kΩ + 60kΩ 22kΩ 3 23 RFN 40pF + 94kΩ FPI 1 2 3 4 5 6 7 3kΩ 22kΩ 2 40pF FNI Pin Symbol I/O No. 24 GND 30kΩ VCC TA2157F Terminal Function 21 AGCIN 20kΩ 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 15pF LDO 7 1.75kΩ 19 RFGO + 40kΩ 6 14kΩ 2kΩ PEAK BOTTOM 1kΩ 18 RFRPIN 20kΩ 8 50kΩ 12kΩ 1.
D-A03 LA1844 (IC402) 24 AL 23 22 21 AM OS AM MI AM RF. AM 20 19 18 17 AG 13 12 STEREO TUNING DRIVE FM DE 2 3 GN FF π 19K ∠ 2 FF PILOT 19K∠0 Vc 5 4 FF 38K VCO 304kHz IF RE 1 PILOT CANCEL COMP S-CURVE 1 13 AM/FM LEVEL DET FM IF Pφ AM DE AM IF TOP VIEW 14 15 DECODER ANTI-BIRDIE BUFF 24 16 6 7 8 9 10 11 12 LA1844 Terminal Function Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 Voltage (V) Function FM IF input 2.34 AM MIX output 5.14 REG 2.33 AM IF input 2.
D-A03 LC72131M (IC401) BA6286 (IC151) CONTROL LOGIC 20 XOUT POWER SAVE FRONT VIEW 15 VDD BO2 7 14 FMIN BO3 8 13 AMIN 4 5 6 7 8 9 10 FIN BO1 6 BA5415A (IC707) 3 VCC 16 PD 2 VM DO 5 1 OUT1 17 AIN 10 GND CL 4 1 RNF 18 AOUT OUT2 DI 3 VREF 19 Vss RIN CE 2 TSD GND XIN 1 FRONT VIEW 1 12 11 IFIN Vcc - + IO1 10 FILTER 12 IO2 ST.BY BO4 9 - + T.S.
D-A03 DIODES 1N4004 1N4148 1N5404 MTZJ5P6B MTZJ6P2A MTZJ7P5A REMOTE CONTROL SENSOR SVC321SP FRONT VIEW IC PROTECTOR RPM6938-V4 (IC604) ICP-N10T (IC152,153) TOP VIEW ROUT GND VCC FRONT VIEW LC DISPLAY TSB0716-UGTDPW (FL501) 68 35 1 34 Pin Connection S60 S59 S58 S57 S56 S55 S54 S53 S52 S51 S50 S49 S48 S47 S46 S45 S44 S43 S42 S41 S40 S39 S38 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 S37 8 S36 7 S35 6 S34 5 S33 4 S32 3 S31 2
D-A03 PRINTED WIRING BOARDS 1 3 2 4 5 6 7 8 MAIN P.W.B.
D-A03 1 2 4 3 5 6 7 8 MAIN P.W.B.
D-A03 1 2 4 3 DISPLAY P.W.B.
D-A03 NOTE FOR PARTS LIST l Part indicated with the mark " " are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused. l When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying. l Ordering part without stating its part number can not be supplied. l Part indicated with the mark " " is not illustrated in the exploded view. l Not including Carbon Film ±5%, 1/4W Type in the P.W.Board parts list.
D-A03 PARTS LIST OF P.W.B. UNIT ASS'Y MAIN P.W.B. UNIT ASSY Ref. No. Part No. Part Name Remarks SEMICONDUCTORS GROUP Note : The symbols in the column “Remarks” indicate the following destinations. E1H: Hong Kong model E3 : U.S.A. & Canada model Ref. No. Part No.
D-A03 Ref. No. Part No. Part Name Remarks Ref. No. Part No. Part Name R141 951 9002 655 Carbon chip 150 kohm 1/16W R419 951 9002 956 Carbon chip 7.5 kohm 1/16W R142 951 9002 927 Carbon chip 5.
D-A03 Ref. No. Part No. Part Name Remarks Ref. No. Part No. Part Name R620,621 951 9002 684 Carbon chip 1 kohm 1/16W R719,720 951 9002 684 Carbon chip 1 kohm 1/16W R622 951 9002 794 Carbon chip 2.2 kohm 1/16W R722 951 9002 639 Carbon chip 10 kohm 1/16W R623,624 951 9002 684 Carbon chip 1 kohm 1/16W Remarks R625,626 951 9002 794 Carbon chip 2.
D-A03 Ref. No. Part No. Part Name Remarks Ref. No. Part No. Part Name C152 951 9001 928 Ceramic chip 0.033uF/50V C406 951 9003 379 Electrolytic 10uF/25V C153 951 9001 931 Ceramic chip 0.047uF/50V C409 951 9001 915 Ceramic chip 0.022uF/50V C154 951 9003 586 Ceramic chip 0.068uF/16V C410 951 9003 395 Electrolytic 100uF/16V C155 951 9001 892 Ceramic chip 0.01uF/50V C412 951 9003 654 Electrolytic 22uF/16V C156 951 9001 928 Ceramic chip 0.
D-A03 Ref. No. Part No. Part Name Remarks Ref. No. Part No. Part Name C479 951 9001 753 Ceramic chip 22pF/50V C801-804 951 9003 719 Electrolytic 47uF/25V C480 951 9003 395 Electrolytic 100uF/16V C805,806 951 9002 516 Mylar film 0.22uF/50V C807,808 951 9003 405 Electrolytic 2200uF/10V 951 9003 803 Electrolytic 220uF/25V C601 951 9001 915 Ceramic chip 0.
D-A03 Ref. No. Part No. Part Name Remarks Part No. Part Name JK301 951 0059 801 Mini jack 1 UL PVC tube (1) JK302 951 0059 704 1P pin jack 1 UL PVC tube (2) JK303 951 0010 808 Mini jack 1 951 9002 600 Carbon chip 0 ohm 1/16W JP176,177 GP3 8002 006 Diode 1N4148 JP23-26 1 Ref. No.
D-A03 DISPLAY P.W.B. UNIT ASSY Ref. No. Part No. Part Name Remarks SEMICONDUCTORS GROUP IC501 951 0023 400 IC LC75811W D501 GP3 8002 006 Diode 1N4148 RESISTORS GROUP R501 951 0025 204 Metal oxide 2.2 ohm 1W R502 951 9002 820 Carbon chip 33 kohm 1/16W R503 951 9002 859 Carbon chip 3.3 kohm 1/16W R504 951 9002 875 Carbon chip 3.9 kohm 1/16W R505 951 9002 642 Carbon chip 12 kohm 1/16W R506 951 9003 476 Carbon chip 8.
D-A03 EXPLODED VIEW 1 4 3 2 5 6 7 8 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
D-A03 (There is no MD section in the U.S.A. and Canada model.) Note : The symbols in the column “Remarks” indicate the following destinations. E1H : Hong Kong model E3 : U.S.A. & Canada model PARTS LIST OF EXPLODED VIEW Ref. No. 18 22 24 25 51 51 78 78 80 80 81 82 86 90 90 91 93 93 94 1 2 3F 3 5 6 7F 7 8 11 12 13F 13 16 17 20 20 21 23 28 28 29 30 31 33 34 36 38 39 40 42 42A 43 Part No.
D-A03 EXPLODED VIEW OF MD MECHANISM 1 2 3 4 (Hong Kong model) A B C D E 60
D-A03 PARTS LIST OF MD MECHANISM Ref. No. (For Hong Kong model) Part No.
D-A03 ADDEMDUM PARTS LIST OF MD MECHANISM MAIN P.W.B. UNIT ASS’Y (MDM08AD) (For Hong Kong model) Ref. No. Part No. Part Name Note: All parts, except for the following, are the same that of used of DMD-M50(MDM08A).
D-A03 PACKING VIEW 180 207 209 202 , 215 216 205 203 201 Note : The symbols in the column “Remarks” indicate the following destinations. E1H : Hong Kong model E3 : U.S.A. & Canada model PARTS LIST OF PACKING & ACCESSORIES Ref. No. 201 202 203 205 206 207 208 209 210 210 211 212 213 Part No.
D-A03 WIRING DIAGRAM 1 4 3 2 Japanese E1 E3 100V 50/60Hz AC 115V-230V 50Hz 120V 60Hz 5 6 7 8 A CORD HOLDER POWER TRANS EARTH WIRE CX034 CY111 GND L-out POWER/AMP P.W.B. B R-out GND F701 2.5A~250V F702 4A~125V CX035 TO SPEAKER POWER KEY P.W.B. CY061 OPEN/CLOSE KEY P.W.B. W104 FUNCTION-KEY P.W.B. CW 023 CX031 CX023 CX033 TO CD MECHANISM AUX/SWF P.W.B. CX022 CX151 CW031 CW 022 CD SWITCH C CD MOTOR CD SWITCH CX062 TUNER P.W.B.
D-A03 SCHEMATIC DIAGRAMS (1/5) 1 2 3 4 7 6 5 8 10 9 11 A E1H(1~600) E3, E1H(601~) R387, 388 8.2K R319, 320 10K 2K TR305, 306 OPEN DTC323TK R321, 322 OPEN 0 W R369 OPEN 0 W C341, 342 47/50 4.7/50 R365, 366 100K 1K 9V B 4.8V 9.7V R635 R693 E1H 10K OPEN E3 OPEN 10K 0V 4.8V 0V C 5V D 5V 0V 1.3V WARNING Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-A03 SCHEMATIC DIAGRAMS (2/5) 1 2 3 4 7 6 5 8 6 10 9 11 7 A 9 18 1 13 14 19 21 20 23 22 17 4 5 10 11 B 8 C 3 12 2 24 D E 15 F 16 NOTICE WARNING ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics.
D-A03 SCHEMATIC DIAGRAM (3/5) 1 4 3 2 R805,806 E1H 2K 5 6 7 8 E3 4.3K A B +10V C +8V +5.5V F701 F702 E1H T4A/250V T2.5/250V E3 4A/125V 2.5/250V D +6V SIGNAL LINE WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. NOTICE CAUTION: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD.
D-A03 SCHEMATIC DIAGRAM (4/5) 1 3 2 4 5 6 7 8 A B C D WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. NOTICE CAUTION: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
D-A03 SCHEMATIC DIAGRAM (5/5) 1 3 2 4 5 6 7 8 A B C D WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. NOTICE CAUTION: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.
