For U.S. & Canada model Hi-Fi Personal Component System SERVICE MANUAL MODEL D-107 PERSONAL AUDIO SYSTEM Some illustrations using in this service manual are slightly different from the actual set.
D-107 SAFETY PRECAUTIONS The following check should be performed for the continued protection of the customer and service technician. LEAKAGE CURRENT CHECK Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the unit is defective.
D-107 DISASSEMBLY (Follow the procedure below in reverse order when reassembling) Note: This system has a feature to back-up various settings such as function selected, volume level, etc. By performing disassembly or checking of the system, this back-up function can be a cause of error, and the system may not work normally when power on after re-assembling. To avoid this error, short-circuit both leads (+ and - terminals) of C110 on 1U-3398-1 (Main PWB) for more than 60 sec.
D-107 Cable E 2. Main P.W.B. A 1) Disconnect connector 2) Remove 4 screws 4 and cable E . 4 Connector A 4 . 4 4 3. I/O P.W.B. 1) Remove 2 screws 5 5 I/O P.W.B. . 5 4. Door Panel 1) Turn the pulley counter-clockwise to open the Door about 10mm horizontally. Note: Be careful not to disengage or twist the belt. 2) Remove 2 screws direction.
D-107 5. Top Panel Top Panel (A) 1) Open rear of the Top Panel in the arrow direction (A). 2) Pull it out horizontally as shown in the arrow direction (B). (B) 6. Control P.W.B. 1) Remove 2 screws 7 to separate the Top Panel and Tact Knob Bracket. 2) Remove 2 screws 8 . 7 7 8 Control P.W.B. Tact Knob Bracket 9 9 7. Mecha. Unit 1) Remove 4 screws 9 . 2) Remove 2 screws . 3) Lift up the Mecha. and disconnect the cable. 4) Open the Mecha. and remove 1 screw fixing the wire.
D-107 8. Display P.W.B. 1) Remove 2 screws . 2) Detach the P.W.B. with lifting as shown and sliding in the arrow direction. Display P.W.B. 9. OP/CL SW P.W.B., Play P.W.B. 1) Remove 1 screw ! . 2) Detach the P.W.B. by moving to the arrow direction. ! (The same for the other P.W.B., right and left symmetrical.) # 10. Interface P.W.B. 1) Remove 1 screw from its clamper. " and 2 screws " # , and release the wire # 11.
D-107 TR MECHA SUB ASS'Y DISASSEMBLY 1. Remove 4 Cut Washers and 2 Slide Cams on both sides of the Mecha. Slide Cam Cut Washer Slide Cam Cut Washer 2. Disconnect 10P ZH-ZH Connector Cord from CX101, then detach the Door Ass’y. Note: When re-assembling Door Ass'y, align the groove on Door Shaft P with the slit of Mecha Chassis respectively. CX101 Door Shaft P Door Ass'y 10P ZH-ZH Conn.
D-107 3-1. Disengage one each side of 2 TR Springs. Only TR Holder side, don’t disengage Mecha Chassis side. 3-2. Disconnect 2P ZR Connector Cord from CX021, and 4P ZH-ZH Connector Cord from CX042. 3-3. Remove 4 pcs of Special Screw fixing the TR Holder. TR Holder TR Spring Mecha Chassis Special Screw Disengage TR Holder side (lower hook) only CX021 TR Spring CX042 Special Screw 2P ZR Conn. Cord 4P ZH-ZH Conn. Cord 4-1. Release 4 PWB Holders for IF Unit. P.W.B. Holder (H=6.35) 4-2.
D-107 5. Short-circuit the Shorting Land on FPC of TR Mecha Sub Ass'y by soldering on the pattern. Pick-up SF-P200R FPC Note: Be sure to short-circuit while FPC is still connected with IF Unit. Also, remove solder on the Shorting Land after connecting it with IF Unit. Seen from the pattern side Shorting Land 2.6×6 Screw(P)-Z FPC 6-1. Detach FPC of TR Mecha Sub Ass'y from IF Unit, then disconnect it from CX162. 6-2. Remove 4 pcs of 2.
D-107 SUB WOOFER DISASSEMBLY Caution:Be sure to check that there is no jarring sound from sub-woofer or no air-leak through joints of parts after reassembling by playing CD source (ordinary music source) with volume indication level 30. 1. SP Terminal Unit, System Conn. Unit AC Conn. Unit 1) Remove 4 screws 1 to detach the Rear Plate. 2) Disconnect 1 cable from the AC Conn. Unit and 3 cables from the System Conn. Unit. 3) Disengage fasten terminal on SP Terminal right.
D-107 3. Back Cabinet, Front Cabinet 1) Remove 10 screws 9 . 2) With holding the Back Cabinet, pull both sides of the Front Cabinet in the arrow direction. Front Cabinet arrow part Note: Use a rubber hammer etc. to hit the of the Front Cabinet if it’s hard to remove. 9 3) Push the Front Cabinet to the arrow direction to make a gap between the Back Cabinet. 4) Cut the wire clamp band near the Front Cabinet, and disconnect 4 cables on the Pre Amp Unit.
D-107 SPEAKER DISASSEMBLY 1. Front Panel 1) Remove 2 screws 1 . 2) Lift up bottom end of the Front Panel as shown to release the hook. Note: Unit change will be necessary if farther disassembling is needed.
D-107 NOTE IN HANDLING FOR LASER PICK-UP Caution for Handling the Laser Pick-up The laser pick-up is assembled and precisely adjusted using a sophisticated manufacturing process in our plant. Do not disassemble or attempt to readjust it. Please observe the following instructions carefully in handling the pick-up. 1. Handle with Care (1) Storage Do not store the pick-up in dusty, high-temperatured or high-humidity environments.
D-107 MECHANISM AND FUNCTION OF CD MECHA 1. Traverse Mecha : TR Mecha Sub Ass’y (GEN5327) 2. Door Open/Close Mechanism: Driven by the door open/close motor, Open SW and Close SW are equipped for checking stop position. 3. Disc Transfer Mechanism: Driven by the holder up-down motor, Out SW, Clamp SW, and In SW are equipped for checking stop position.
D-107 2 1 3 4 5 6 7 8 Loader Mecha Timing Chart Timing Chart when close 1 sec. 49 pin DISC_SW Hi 50 pin 12cm_SW 46 pin CLOSE_SW Descends holder after 1sec. when DISC_SW(H) and 12cm_SW (L) conditions are satisfied. Lo Hi ↑ 1. Disc Detect Defines as 8cm disc insertion in case of DISC_SW(H) and 12cm_SW (H), and repeats holder up/down 10 times. Lo Hi 47 pin OPEN_SW ↑ 7. Door Close Stop Lo Hi ↓ 9. Holder Retract End (pulse decline stop) Lo ↓ 6.
D-107 2 1 3 4 5 6 7 8 Loader Mecha Timing Chart Timing Chart when open ↓ Unload Disc ↓ Open Key Press 49 pin DISC_SW Hi A Lo 50 pin 8cm_SW Hi Lo Hi 46 pin CLOSE_SW ↑ 4. Door Open Start Hi ↑ 5. Door Open Stop ↑ 6. Holder Up Start Lo 43 pin IN_SW (Retract Position) Hi Lo ↓ 3. Door Pulse Open Start (pulse open) ↓ 2. Holder Receiving End (pulse rise stop) 44 pin Hi CLAMP_SW 33 pin DISC_DOWN Hi B ↑ 1. Holder Receiving Start (pulse rise start) ↑ 7.
D-107 CONFIRMATION METHOD OF ADJUSTMENT In the µcom of this system, there is a built-in function “adjustment confirmation mode” to check various servo control easily with CD operation buttons. Also, focus offset, tracking offset, tracking balance, focus gain, and tracking gain are all adjusted automatically as the digital servo control is built in the system. 1. Activating Adjustment Confirmation Mode (1) Load the test disc TCD-784 or Mozart (CO-74176) at the function CD.
D-107 Table1 Servo Adjust Value Confirmation List Fdoffset Tdoffset EAh~0Eh EAh~0Eh EAh~FFh EAh~FFh or or 00h~0Eh 00h~0Eh Tbal Fogain Trgain 6Bh~9Ah 28h~56h 28h~56h Value indicated are hexadecimal (HEX) Fbal value indicated fourth in the item of adjusted value check will be displayed always as 00h because no adjustment is made. When out of the range value appears, open and close the door once, then check the value again.
D-107 3. How to Check HF Level (1) Measuring instruments required a) Oscilloscope b) Test disc: TCD-784 (A-BEX) or Mozart (CO-74176) (2) Attaching connection wire for checking HF level a) Disassemble 1U-3398-1 (Main PWB) → Refer to “DISASSEMBLY” on page 3, 4. b) Solder wires to RF and VC test points for connecting the probe of oscilloscope. (Length of the wires should be less than 20 cm) → Refer to 1U-3398-1 drawing on page 32. c) Assemble 1U-3398-1, see the diagram below.
D-107 BLOCK DIAGRAMS 1 2 3 4 5 6 7 8 UD-107 BLOCK & WIRING DIAGRAM FG350 POWER ON/ STANDBY LED CX211 IC201 IC202 MOTOR DRIVER IC204 DSP TACT SW A CY051 5P FFC (P=1) 16P FFC (P=1) (Mecha side inserted) ) 21P FFC (P=1) (Mecha side inserted) CX161 1U-3398-7 CONTROL UNIT 1U-3398-8 MAIN UNIT IC203 MP3 CX051 B IC208 DRAM IC204 IC203 IC208 IC207 Reg. +3.3V V +5V-D1 AUX IN AUX OUT IC101 µCOM 11P TWGP OPT.OUT IC305 EQ&VR 1U-3398-4 AUDIO I/O UNIT TUNER PACK CX151 15P FFC (P=1.
D-107 2 1 3 4 5 6 7 8 USW-107 BLOCK & WIRING DIAGRAM UD-107 A 20P DISM CY031 CX031 6P PH-PH CX061 CY061 6P PH-PH 10P EH-EH CY101 IC202 Reg. +6V 11P PH-PH CY111 AUDIO SIG. HPF/LPF ALC CX101 IC201 Reg. +12V CX111 12P PH-PH CX121 CY121 1U-3445-1 SYSTEM CONN UNIT 1U-3417-1 POWER AMP UNIT 1U-3400-1 POWER SUPPLY UNIT TR201 Reg.
D-107 LEVEL DIAGRAM 1 2 3 4 5 6 7 8 D-107 LEVEL DIAGRAM UD107 USW107 LC75396NE TUNER SOURCE CD INPUT FUNCTION SWITCH AUX IN EQ V O L U M E A L/R POWER AMP HPF 200Hz L/R SPEAKER SUB WOOFER BPF PEAK 70Hz ALC SUB WOOFER AUX OUT B +30dBV SUB WOOFER +20dBV L/R +10dBV AUX INPUT 2V AUX 0dBV L/R ALC ON CD 0dB -10dBV C VOLUME -10dB STEP54 ALC OFF -20dBV VOLUME -20dB STEP44 -30dBV D E 22 D107_Level.p65 Page 6-7 02/01/15, 17:03 Adobe PageMaker 6.
D-107 SEMICONDUCTORS Pin No. IC’s S46/PF6 S45/PF5 S44/PF4 S43/PF3 S42/PF2 S41/PF1 S40/PF0 S39/PE7 S38/PE6 S37/PE5 S36/PE4 S35/PE3 S34/PE2 S33/PE1 S32/PE0 S31/PD7 S30/PD6 S29/PD5 S28/PD4 S27/PD3 S26/PD2 S25/PD1 S24/PD0 VSS2 VDD2 Note: Indication before IC No. (SW) denotes “USW-107”.
D-107 MADRS0 MADRS1 MADRS2 MADRS3 MADRS4 MADRS5 MADRS6 MADRS7 VSS DVDD4 MADRS8 MADRS9 MADRS10 MADRS11 MADRS12 OEB CASUB CASLB WEB RASB 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 18 19 20 VCOC VPDO AVSS TOP VIEW 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 LRSY ADDATA ADBCK ADLRCK C2FIN VSS CKIN VSS CKOUT VSS DVDD1 PW SBSY SFSY SBCK AVDD VPRFR DVDD5 VSS STREQ STCK STDAT FSYNC CRCF DVDD6 VSS WOK CNTOK OVF CMDOUT CMDIN C
D-107 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 DATA DATACK LRSY ASDFIN ASDACK ASLRCK 16MOUT EFLG C2F XVSS FSX/16MIN XIN XOUT XVDD RVDD RCHO RVSS LVSS LCHO LVDD LC78645E (IC204) 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 TOP VIEW SLCO SLCIST EFMIN RF RFVDD RFVSS FIN1 FIN2 TIN1 TIN2 VREF REFI FE TEC TE RFMON JITTC ADAVDD ADAVSS TDO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CE CL DI DO ∗WRQ ∗RES DR
D-107 M66004FP (IC701) 1 1 0 2 0 9 3 0 8 4 0 7 5 0 6 6 0 5 7 0 4 D IG D IG D IG D IG R E S E C S C S D A T 0 3 0 2 8 9 1 0 0 1 1 1 0 0 1 2 S E S E S E S E S E S E S E S E S E T 1 3 S 1 4 K 1 5 A 1 6 P I 1 7 P O 1 8 V c c 1 1 9 X out 2 0 X in 2 1 V s s 2 2 G 35 2 3 G 34 2 4 G 33 2 5 G 32 2 6 G 31 2 7 G 30 2 8 G 29 2 9 G 28 3 0 G 27 3 1 V p 3 2 6 4 D 6 3 D 6 2 D 6 1 D 6 0 V 5 9 S 5 8 S 5 7 S 5 6 S 5 5 S 5 4 S 5 3 S 5 2 S 5 1 S 5 0 S 4 9 S 4 8 S 4 7 S 4 6 S 4 5 S 4 4 S 4 3 S 4 2 S 4 1 S
D-107 LA6559 (IC201) Pin No. Thermal Shutdown REV 1 S-VCC 2 VCC2 3 Input Power Supply (LOADING) (Forward/Reverse/ Break/OFF) Output Control VLO- 4 VLO+ 5 Signal System GND 34 MUTE2 CH1 Output ON/OFF MUTE1 33 MUTE1 31 VIN4- 11k 30 VIN4+ Level Shift 29 VREF-IN VO3- 9 28 VCONT(LOADING) Power System GND Power System GND PNP Tr Collector Level Shift VO2+ 10 VO2- 11 Level Shift VO1- 13 VIN1 15 3.
D-107 LF5 LTOUT LFIN 40 LF4C3 41 LF4C2 42 LF4C1 LF3C2 44 43 39 38 37 36 35 34 33 LF3C3 LF3C1 46 45 LF2C3 47 LF2C2 LF1C2 48 LF2C1 LF1C1 LF1C3 LTIN LC75396NE (IC305) LSELO 49 32 LFCOM LINVIN1 50 31 LFOUT L5 51 30 LRIN L4 52 29 LRCOM L3 53 28 LROUT L2 54 27 LVref L1 55 26 VSS VDD 56 25 CE TOP VIEW R1 57 24 DI R2 58 23 CL R3 59 22 Vref R4 60 21 RVref R5 61 20 RROUT RINVIN1 62 19 RRCOM RSELO 63 18 RRIN RTIN 64 7 8 9 10 RF1C2 RF1C3 RF2C1 RF2C2
D-107 BA033S (IC207) BA6417F (IC202) BA15218F (IC301, 303, 401) (SW: IC101, 102, 105, 106, 401 ) 3 OUT1 1 IN1 2 8 Vcc −1ch+ 2ch OUT1 1 8 GND 7 OUT2 VM 2 7 OUT2 6 Vcc 6 VRFF + − +IN1 3 1 2 4 5 VEE 4 IN2 5 +IN2 3 FIN 4 5 RIN 1.CTL 2.Vcc 3.GND 4.OUT 5.N. C.
D-107 TRANSISTORS DTA114TK DTC114EK DTC323TK DTC114EK DTC323TK DTA114TK PNP Type 2SC3326 (A/B) NPN Type C 2 C 2 TOP VIEW B B 3 1 3 TOP VIEW R1 R1 R2 R2 1: GND/Emitter 2: Out/Collector 3: In/Base R2 R1 1: Emitter 2: Collector 3: Base E E R1 DTA114TK 10kohm 10kohm 1 R2 DTC114EK 10kohm 10kohm DTC323TK 2.2kohm 2.
D-107 PRINTED WIRING BOARDS 4 3 2 5 6 7 1U-3398 CD-TUNER UNIT ASS'Y 13 8 1 12 1 1 3 1 3 2 3 1 3 A 1 11 2 1 2 4 5 10 1 8 4 5 B 20 11 12 1 2 12 29 1 2 13 2 1 1 10 2 28 HF Level Check Point 5 8 C 4 15 1 2 21 10 20 11 2 1 1 20 1 21 16 80 61 40 60 41 15 1 14 2 1 2 2 49 48 16 33 26 25 51 13 17 76 100 32 20 1 21 80 28 29 D 1 75 24 5 1 50 64 1 4 1 1 12 61 40 41 60 E 6 1 SIDE - A 31 XX
D-107 1 4 3 2 5 6 7 8 1U-3398 CD-TUNER UNIT ASS'Y 32 1 33 64 A B HF Level Check Point 36 19 1 18 C 4 1 5 8 D 20 21 1 E 40 SIDE - B 32 32
D-107 1 4 3 2 5 6 7 8 1U-3400 POWER SUPPLY UNIT ASS'Y A 1 1 2 B 1 1 1 2 13 10 1 13 2 11 C 1 D 6 12 1 1 CUATION : C231, 205, 216, 246, 221, 220, 223, 247, 248, 249, RL201, AS201, AS218, and Heat Sink must be fixed with hot-melt or bond.
D-107 1 2 3 4 5 6 7 8 1U-3400 POWER SUPPLY UNIT ASS'Y A B 4 1 5 8 4 1 5 8 4 5 C 1 4 1 8 5 8 D FOIL SIDE E 34 XX
D-107 1 4 3 2 5 6 7 8 1U-3401 CD MECHA P.W.B. UNIT ASS'Y A 1 1 1 4 3 4 B 1 21 2 15 1 1 16 3 1 4 2 6 C 15 1 16 1 2 10 D 1 2 1 4 1 10 E 1 20 COMPONENT SIDE Two pieces of 1U-3401-7 LED Unit are arranged on the P.W.B., one for actual use and the other for spare.
D-107 1 2 4 3 5 6 7 8 1U-3417 POWER AMP UNIT ASS'Y 1 4 11 1 1 10 1 2 1 4 1 3 A 1 B 1 CUATION : C503~505, C513, C516, C703~705, C713, C716 L500, 501, L700, 701, RL500, and RL700, must be fixed with hot-melt or bond.
D-107 1 4 3 2 1U-3445 I/F UNIT ASS'Y A B 1 10 20 1 1 6 12 C 1 COMPONENT SIDE 8 5 1 4 3 FOIL SIDE D E 37
D-107 NOTE FOR PARTS LIST l Part indicated with the mark " " are not always in stock and possibly to take a long period of time for supplying, or in some case supplying of part may be refused. l When ordering of part, clearly indicate "1" and "I" (i) to avoid mis-supplying. l Ordering part without stating its part number can not be supplied. l Part indicated with the mark " " is not illustrated in the exploded view. l Not including Carbon Film ±5%, 1/4W Type in the P.W.Board parts list.
D-107 PARTS LIST OF P.W.B. UNIT ASS'Y 1U-3398 CD-TUNER UNIT ASS'Y Ref. No. Part No.
D-107 Ref. No. Part No. Part Name Remarks Ref. No. Part No. Part Name Remarks R231 247 2010 956 Carbon chip 20 kohm 1/16W RM73B--203JT R382~384 247 2018 903 Carbon chip 0 ohm 1/16W RM73B--0R0KT R232~235 247 2010 969 Carbon chip 22 kohm 1/16W RM73B--223JT R385 247 2001 907 Carbon chip 2.2 ohm 1/16W RM73B--2R2KT R236,237 247 2011 913 Carbon chip 36 kohm 1/16W RM73B--363JT R386 247 2002 948 Carbon chip 8.
D-107 Ref. No. Part No. Part Name Remarks Ref. No. Part No. Part Name 254 4302 974 Electrolytic 100µF/10V Remarks C133 257 0512 903 Ceramic chip 0.1µF/25V CK73F1E104ZT C270 CE04W1A101MT(SRE) C134 257 0501 901 Ceramic chip 0.01µF/50V CK73B1H103KT (1608) C271,272 257 0512 903 Ceramic chip 0.1µF/25V CK73F1E104ZT C135,136 257 0512 903 Ceramic chip 0.
D-107 Ref. No. C373,374 Part No. Part Name 254 4193 934 Electrolytic 47µF/16V Remarks CE04W1C470MT (SRA) Ref. No. C543 Part No. Part Name 257 0512 903 Ceramic chip 0.1µF/25V Remarks CK73F1E104ZT C377,378 257 0506 951 Ceramic chip 100pF/50V CC73CH1H101JT C383 257 0512 903 Ceramic chip 0.1µF/25V CK73F1E104ZT C701~703 257 0506 951 Ceramic chip 100pF/50V CC73CH1H101JT C384,385 254 3068 905 Electrolytic 1µF/50V CE04D1H010MBPT(SRA) C704 257 0512 903 Ceramic chip 0.
D-107 1U-3400 POWER SUPPLY UNIT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty L201 235 0088 932 Chip inductor (4R7MF) 1 S801 212 0469 901 Tact switch 1 S803 212 0469 901 Tact switch 1 S805 212 0469 901 Tact switch S807 212 0469 901 Tact switch S809 Ref. No. Part No.
D-107 Ref. No. R178 Part No. Part Name Remarks Ref. No. Part No. Part Name Remarks 247 2009 983 Carbon chip 10 kohm 1/16W RM73B--103JT C191 257 0501 901 Ceramic chip 0.01µF/50V CK73B1H103KT (1608) R179 247 2008 984 Carbon chip 3.9 kohm 1/16W RM73B--392JT C192 257 0511 920 Ceramic chip 0.
D-107 1U-3401 CD MECHA P.W.B. UNIT ASS'Y Ref. No. Part No. Part Name Remarks Q'ty OTHERS PARTS GROUP Ref. No. Part No.
D-107 1U-3417 POWER AMP UNIT ASS'Y Ref. No. Part No. Part Name Remarks Ref. No. Part No.
D-107 Ref. No. Part No. Part Name Remarks Ref. No. Part No. Part Name Remarks Q'ty C533,534 254 4524 943 Electrolytic 1µF/50V CE04W1H010MT SMG/RE3 OTHERS PARTS GROUP C700 257 0512 903 Ceramic chip 0.1µF/25V CK73F1E104ZT C701 254 3056 920 Electrolytic 2.
D-107 1U-3445 I/F UNIT ASS'Y Ref. No. Part No. Part Name Remarks SEMICONDUCTORS GROUP IC401 263 0615 902 IC BA15218F-DXE2 RESISTORS GROUP R401~408 247 2009 983 Carbon chip 10 kΩ 1/16W RM73B--103JT CAPACITOR GROUP C401,402 257 0512 903 Ceramic chip 0.1 µF/25V C403,404 257 0506 951 Ceramic chip 100 pF/50V CC73CH1H101JT C601 257 0512 903 Ceramic chip 0.1 µF/25V CK73F1E104ZT C604,605 257 0512 903 Ceramic chip 0.1 µF/25V CK73F1E104ZT C610 257 0512 903 Ceramic chip 0.
D-107 EXPLODED VIEW 1 4 3 2 5 21 6 37 7 8 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
D-107 PARTS LIST OF EXPLODED VIEW Ref. No. 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Part No.
D-107 EXPLODED VIEW OF CD MECHANISM 1 4 3 2 5 6 7 8 106 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. 44 45 106 A 50-4 35 105 49 CAUTION: The No.100 screws (marked with , 4pieces) are provided for transportation and production (pully protection). Be sure to remove them after assembling into the unit.
D-107 PARTS LIST OF CD MECHANISM UNIT Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 50-1 50-2 50-3 50-4 Part No. Part Name Remarks Q'ty 411 1997 406 412 4863 006 425 0248 003 477 0315 005 424 0272 102 475 1157 046 424 0273 208 462 0171 001 431 0433 101 424 0271 006 GEN 5325 − 203 2412 004 423 0078 002 463 0948 101 431 0431 006 443 1559 003 445 8004 007 GEN 5327 Mecha chassis ass'y P.W.B.
D-107 EXPLODED VIEW OF SUB WOOFER 1 4 3 2 5 6 7 WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
D-107 PARTS LIST OF SUB WOOFER UNIT Ref. No. Part No.
D-107 PACKING VIEW USW-107 UD-107 225 226 215 216 211 USC-107 217 227 208 204 205 228 222 219 213 207 214 210 212 221 220 203 209 202 206 218 201 223 224 PARTS LIST OF PACKING & ACCESSORIES Ref. No. 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 Part No.
D-107 FORMING CUSHIONS How to Form USW Cushion Top * Solid lines: Convex shape. Doted lines: Concave shape. 1. USW CUSHION TOP-L 2. USW CUSHION TOP-R How to Form Spacer (Center) Cushion 3.
D-107 How to Form USW BTM-L/R Cushion * Solid lines: Concave shape. Doted lines: Convex shape. A Cut 4. USW CUSHION BTM-L Cut A 5. USW CUSHION BTM-R Hold the cushion in the order as shown (L-side). As for R-side, it is reverse directional from this Fig.
D-107 How to Form Cushion Top How to Form Cushion BTM * Solid lines: Convex shape. Doted lines: Concave shape. 1. UD CUSHION TOP-B 1. UD CUSHION BTM-B 2. UD CUSHION TOP-A 2. UD CUSHION BTM-A Assemble 2 cushions combining them vertically, top and bottom.
D-107 WAVE FORMS AC ON CD PLAY 1 2 11 3 4 CD PLAY CD PAUSE 5 12 6 13 7 14 8 15 FOCUS ON MP3 PLAY 5 16 6 17 7 18 8 FOCUS ON MP3 PLAY 5 19 6 7 20 21 8 CD STOP → PLAY 5 6 9 10 59
D-107 D-107 SCHEMATIC DIAGRAMS (1/6) 1 2 3 4 5 6 7 8 9 10 D-107 11 D-107 D-107 A D-107 D-107 B 1 C 3 2 D 4 E 16 17 18 15 14 13 12 21 20 11 19 7 8 F 6 5 9 + B LINE 10 - B LINE SIGNAL LINE WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. G CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
D-107 D-107 SCHEMATIC DIAGRAMS (1/6) 1 2 3 4 5 6 7 8 9 10 D-107 11 D-107 D-107 A D-107 A B 1 D-107 B C 3 2 D 4 E 16 17 18 15 14 13 12 21 20 11 C 19 7 8 6 5 9 D + B LINE 10 - B LINE SIGNAL LINE F WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 D-107 SCHEMATIC DIAGRAMS (1/6) 1 2 3 4 5 6 7 8 9 10 D-107 11 D-107 D-107 A D-107 D-107 B 1 C 3 2 D 4 E 16 17 18 15 14 13 12 21 20 11 19 7 8 F 6 5 9 + B LINE 10 - B LINE SIGNAL LINE WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. G CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
D-107 D-107 SCHEMATIC DIAGRAMS (1/6) 1 2 3 4 5 6 7 8 9 10 D-107 11 D-107 D-107 A D-107 D-107 B 1 C 3 2 D 4 E 16 17 18 15 14 13 12 21 20 11 19 7 8 F 6 5 9 + B LINE 10 - B LINE SIGNAL LINE WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. G CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
D-107 D-107 SCHEMATIC DIAGRAMS (1/6) 1 2 3 4 5 6 7 8 9 10 D-107 11 D-107 D-107 A D-107 D-107 B 1 C 3 2 D 4 E 16 17 18 15 14 13 12 21 20 11 19 7 8 F 6 5 9 + B LINE 10 - B LINE SIGNAL LINE WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. G CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
D-107 D-107 SCHEMATIC DIAGRAMS (1/6) 1 2 3 4 5 6 7 8 9 10 D-107 11 D-107 D-107 A D-107 D-107 B 1 C 3 2 D 4 E 16 17 18 15 14 13 12 21 20 11 19 7 8 F 6 5 9 + B LINE 10 - B LINE SIGNAL LINE WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture. G CAUTION: Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis resistance check.
D-107 SCHEMATIC DIAGRAMS (2/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (2/6) 1 2 3 4 5 6 7 8 9 10 11 A A B B C D E C D NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (2/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (2/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (2/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (2/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (3/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E + B LINE - B LINE SIGNAL LINE F G NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (3/6) 1 2 3 4 5 6 7 8 9 10 11 A A B B C D E C + B LINE - B LINE D SIGNAL LINE NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (3/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E + B LINE - B LINE SIGNAL LINE F G NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (3/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E + B LINE - B LINE SIGNAL LINE F G NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (3/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E + B LINE - B LINE SIGNAL LINE F G NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (3/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E + B LINE - B LINE SIGNAL LINE F G NOTICE WARNING: ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (4/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. F WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (4/6) 1 2 3 4 5 6 7 8 9 10 11 A A B B C D E C D NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. F WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (4/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. F WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (4/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. F WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (4/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. F WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (4/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. F WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (5/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. E WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (5/6) 1 2 3 4 5 6 7 8 9 10 11 A A B B C D NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. E WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (5/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. E WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (5/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. E WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (5/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. E WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (5/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. E WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (6/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE - B LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (6/6) 1 2 3 4 5 6 7 8 9 10 11 A A B B C D E C + B LINE - B LINE NOTICE D F ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (6/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE - B LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (6/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE - B LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (6/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE - B LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
D-107 SCHEMATIC DIAGRAMS (6/6) 1 2 3 4 5 6 7 8 9 10 11 A B C D E F + B LINE - B LINE NOTICE ALL RESISTANCE VALUES IN OHM. k=1,000 OHM M=1,000,000 OHM ALL CAPACITANCE VALUES IN MICRO FARAD. P=MICRO-MICRO FARAD EACH VOLTAGE AND CURRENT ARE MEASUERD AT MO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. G WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacture.
