Owner's Manual
Table Of Contents
- Owners Manual
- Reset
- Features
- Table of Contents
- Panel Lock Function
- Video Comversion
- Supplied Accessories
- Parts & Controls
- Connections
- Cables Used for Connection
- Speaker Installation / Placement
- Connecting Speakers
- Subwoofer
- About Cable Labels
- Speaker Configuration and Amp Assign Settings
- Bi-Amp Connection
- Multi-Zone Speakers
- TV
- Playback Devices
- USB Device
- Antennas
- Home Network
- Connecting an External Control Device
- Zone 2 / Zone 3 Connections
- Power Cord
- Playback
- Power On
- Selecting the Input Source
- Volume / Mute
- Playing a Blu-ray / DVD Player
- USB Device
- Bluetooth
- FM / AM Radio
- Internet Radio
- Playing Back Files Stored On a PC and NAS
- Getting the HEOS App
- AirPlay
- Spotify Connect
- Convenience Functions
- Adding to HEOS Favorites
- Playing back HEOS Favorites
- Deleting a HEOS Favorites
- Adjusting the Audibility of Dialog and Vocals (Dialog Enhancer)
- Adjusting the Volume of each Channelto Match the Input Source (Channel Level Adjust)
- Adjusting the Tone (Tone)
- Displaying your Desired Video During Audio Playback (Video Select)
- Adjusting the Picture Quality for your Viewing Environment (Picture Mode)
- Playing the Same Music in All Zones (All Zone Stereo)
- Selecting a Sound Mode
- HDMI Control Function
- Smart Menu Function
- Sleep Timer
- Quick Select Plus Function
- Panel Lock Function
- Remote Lock Function
- Web Control Function
- Playback in ZONE 2 / ZONE 3
- Settings
- About HDMI
- Relationship Between Video Signals and Monitor Output
- Personal Memory Plus
- Last Function Memory
- Sound Modes and Channel Output
- Sound Modes and Surround Parameters
- Types of Input Signals and Corresponding Sound Modes
- Glossary
- Tips
- Troubleshooting
- Specs
- Index
- Quick Start Guide
- Microphone Stand Assembly Instructions
- Speaker Wire Labels
- IMAX DTS Firmware Update Information
- Spotify
- Warranty
o
About the main listening position
The main listening position is the position where listeners would
normally sit or where one would normally sit alone within the listening
environment. Before starting Audyssey
®
Setup, place the Sound
calibration microphone in the main listening position.
Audyssey MultEQ
®
XT32 uses the measurements from this position to
calculate speaker distance, level, polarity, and the optimum crossover
value for the subwoofer.
o
About Audyssey Sub EQ HT™
Audyssey Sub EQ HT™ makes the integration of dual subwoofers
seamless by first compensating for any level and delay differences
between the two subwoofers and then applying Audyssey MultEQ
®
XT32 to both subwoofers together.
To run Audyssey Sub EQ HT™ you must select “Measure (2 spkrs)” in
“Channel Select”. (v p. 212).
NOTE
0
Make the room as quiet as possible. Background noise can disrupt the room
measurements. Close windows and turn off the power on electronic devices
(radios, air conditioners, fluorescent lights, etc.). The measurements could be
affected by the sounds emitted by such devices.
0
During the measurement process, place cell phones outside the listening room.
Cell phone signals could disrupt the measurements.
0
Do not stand between the speakers and Sound calibration microphone or allow
obstacles in the path while the measurements are being made. Also, install the
Sound calibration microphone at least 20 inches (50 cm) away from the wall.
Failure to do so will result in inaccurate readings.
0
During the measurement process, audible test tones will come from the speakers
and subwoofer(s), but this is part of normal operation. If there is background noise
in the room, these test signals will increase in volume.
0
Operating VOLUME d f on the remote control unit or MASTER VOLUME on the
main unit during the measurements will cancel the measurements.
0
Measurement cannot be performed when headphones are connected. Unplug the
headphones before performing Audyssey
®
Setup.
Contents
Connections Playback Settings Tips Appendix
210
Front panel Display Rear panel Remote Index