Owner's Manual

10
ENGLISH
11
2QWKH
STEP3
VFUHHQXVHui
WRVHOHFW³1H[Wo&DOFXODWLRQ´DQG
WKHQSUHVV
ENTER
Measuring results are analyzed, and the
frequency response of each speaker in the
listening room is determined.
$8'<66(<$8726(783

67(3&DOFXODWLRQ
1RZFDOFXODWLQJ3OHDVHZDLW

• Analysis takes several minutes to complete. The
time required for this analysis depends on the
number of speakers connected.
The more connected speakers there are, the
longer it takes to perform analysis.
Set up speakers (Audyssey
®
Auto Setup)
STEP 4
Calculation
STEP 5
Check
12
8VHuiWRVHOHFWWKHLWHP\RXZDQW
WRFKHFNDQGWKHQSUHVV
ENTER
$8'<66(<$8726(783

5(7851
1H[W6WRUH
6HOHFWLWHPWRFKHFN
(QWHU &DQFHO
&URVVRYHU&KHFN
&K/HYHO&KHFN
'LVWDQFH&KHFN
6SNU&RQILJ&KHFN
67(3&KHFN
&KHFNSURFHVVLQJUHVXOWV
7RSURFHHGSUHVV´1H[Wµ
• Subwoofers may measure a greater reported
distance than the actual distance due to added
electrical delay common in subwoofers.
• If you want to check another item, press
RETURN.
13
8VH ui WR VHOHFW ³1H[W o 6WRUH´
DQGWKHQSUHVV
ENTER
14
6HOHFW³6WRUH´DQGWKHQSUHVVENTER
Save the measurement results.
$8'<66(<$8726(783

67(36WRUH
1RZVWRULQJ3OHDVHZDLW

$8'<66(<$8726(783

5(7851
$SSO\DQGVWRUHPHDVXUHPHQWUHVXOW
(QWHU &DQFHO
6WRUH
67(36WRUH
3UHVV´6WRUHµWRVWRUHFDOFXODWLRQUHVXOWV
• Saving the results requires about 20 seconds.
• If the measuring results are not to be saved,
press
RETURN. A message “Cancel auto
setup?” will be displayed. Press o then select
“Yes”. All the measured Audyssey Auto Setup
data will be erased.
NOTE
During saving of measurement results, be sure
not to turn off the power.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confi rm the setting Return to previous menu
NOTE
• If the result differs from the actual connection
status, or if “Caution!” is displayed, see “Error
messages” (vpage11). Then carry out Audyssey
Auto Setup again.
• If the result still differs from the actual connection
status after remeasurement or the error message
still appears, it is possible that the speakers
are not connected properly. Turn this unit off,
check the speaker connections and repeat the
measurement process from the beginning.
• If you change speaker positions or orientation,
perform Audyssey Auto Setup again to fi nd the
optimal equalizer settings.
STEP 6
Store
Finish
15
8QSOXJWKHVHWXSPLFURSKRQHIURP
WKHXQLW¶V6(7830,&MDFN
16
6HW'\QDPLF9ROXPH


$8'<66(<$8726(783

1R
<HV
7XUQ'\QDPLF9ROXPHRQDQGH[LW$XWR6HWXS
([LW
)LQLVK
6WRULQJFRPSOHWH
$XWR6HWXSLVQRZILQLVKHG
3OHDVHXQSOXJPLFURSKRQH
7XUQRQ'\QDPLF9ROXPH"
• For details of Dynamic Volume settings, see
page 90.
n When turning Dynamic Volume on
Use u to select “Yes“, and then press ENTER.
• The unit automatically enters “Evening” mode.
n When turning Dynamic Volume off
Use i to select “No“, and then press ENTER.
NOTE
• After performing Audyssey Auto Setup, do not
change the speaker connections or subwoofer
volume. In event of a change, perform Audyssey
Auto Setup again.
• After performing Audyssey Auto Setup with two
subwoofers, do not change the channel distances
and levels of both subwoofers.