Owner's Manual

9
Basic version Advanced version Information
ENGLISH
Simple version
Set up speakers (Audyssey
®
Auto Setup)
STEP 1
Preparation
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confi rm the setting Return to previous menu
STEP 2
Detection & Measurement
(Main listening position)
STEP 3
Measurement
(2nd – 8th listening position)
7
7KHGHWHFWHGVSHDNHUVDUHGLVSOD\HG
$8'<66(<$8726(783

5(7851
1H[W0HDVXUHPHQW
5HWU\
67(36SHDNHU'HWHFWLRQ&KHFN
)URQW
&HQWHU
6XEZRRIHU
6XUURXQG
6XUURXQG%DFN
)URQW+HLJKW
<HV
<HV
VSNU
<HV
VSNUV
1R
3URFHHGWR67(3DIWHUFKHFNLQJVSHDNHUFRQQHFWLRQUHVXOW
(QWHU &DQFHO
NOTE
If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.
8
8VHuiWRVHOHFW³1H[Wo
0HDVXUHPHQW´DQGWKHQSUHVV
ENTER
• In STEP 3, you will perform measurements at
multiple positions (two to eight positions) other
than the main listening position.
• You can achieve a more effective correction of
distortion within the listening area by performing
measurements at multiple positions.
9
0RYHWKHVHWXSPLFURSKRQHWR
SRVLWLRQXVH
uiWRVHOHFW
³0HDVXUH´DQGWKHQSUHVV
ENTER
The measurement of the second position
starts. Measurements can be made in up to
eight positions.
$8'<66(<$8726(783

5(7851
1H[W&DOFXODWLRQ
0HDVXUH
67(30HDVXUHPHQWQGWK
3OHDVHSODFHWKHPLFURSKRQHDWHDU
KHLJKWDWQG,LVWHQLQJSRVLWLRQ
6WDUWPHDVXUHPHQW2XWSXWODUJHWHVWWRQHGXULQJPHDVXULQJ
(QWHU &DQFHO
If you want to omit measurements from the next
position onward, select “Next o Calculation”.
(Go to
STEP4 Calculation
)
10
5HSHDWVWHSPHDVXULQJSRVLWLRQV
WR
When measurement of position 8 is
completed, a “Measurements fi nished.”
message is displayed.
$8'<66(<$8726(783

5(7851
1H[W&DOFXODWLRQ
3URFHHGWR67(3&DOFXODWLRQ
(QWHU &DQFHO
5HWU\
67(30HDVXUHPHQWQGWK
0HDVXUHPHQWVILQLVKHG
NOTE
If “Caution” is displayed:
Go to “Error messages” (vpage 11), check
any related items, and perform the necessary
procedures.
When performing Audyssey Auto
Setup over again
Press ui to select “Retry”, and then press ENTER .
When measuring has stopped
Press RETURN, to the “Cancel auto setup?” prompt
is displayed.
Press
o to select “Yes”, then press ENTER.
Setting up the speakers again
Repeat the operation from step 4 of
STEP1 Preparation
.
• In STEP 2, you will perform measurements at the
main listening position.
• This step automatically checks the speaker
confi guration and speaker size, and calculates the
channel level, distance, and crossover frequency.
It also corrects distortion in the listening area.
6
6HOHFW ³0HDVXUH´ DQG WKHQ SUHVV
ENTER
$8'<66(<$8726(783

5(7851
0HDVXUH
67(3'HWHFWLRQ0HDVXUHPHQWPDLQ
3OHDVHSODFHWKHPLFURSKRQHDWHDU
KHLJKWDWPDLQ,LVWHQLQJSRVLWLRQ
6WDUWPHDVXUHPHQW2XWSXWODUJHWHVWWRQHGXULQJPHDVXULQJ
(QWHU &DQFHO
q Measure the subwoofer level
• To stop measuring, select “Cancel” and then
press
ENTER.
• When “Subwoofer” is set to “Skip” with
“Channel Select”, this measurement is not
taken, and the process proceeds to “w
Measure each speaker”.
w Measure each speaker
• Once the measurements in step q are
complete, the measurements in step w start
automatically.
• The measuring channel changes depending
on the setting of “Set up “Amp Assign””
(vpage63) and “Set up “Channel Select””
(vpage64).
• Measurement requires several minutes.
4
&RQQHFWWKHVHWXSPLFURSKRQHWRWKH
6(7830,&MDFNRIWKLVXQLW
$8'<66(<$8726(783

$PS$VVLJQ
5(7851
$XWR6HWXS6WDUW
&KDQQHO6HOHFW
67(33UHSDUDWLRQ
&RQQHFWWKHVSHDNHUVDQGSODFHWKHPDFFRUGLQJ
VQVJGUHFRPPHQGDWLRQVLQWKHPDQXDO
6HWWKHIROORZLQJLWHPV
,IQHFHVVDU\
6WDUW$XWR6HWXS
(QWHU &DQFHO
When the setup microphone is
connected, the following screen is
displayed.
This screen provides the method for setting
up 7.1-channel playback using surround back
speakers. For the method of setting up speakers
other than the 7.1-channel system, select “Amp
Assign” and perform step 3 and 7 of “Set up
“Amp Assign”” (vpage63).
If unused channels are set with “Channel Select”,
measuring time can be shortened. Also, set
“Channel Select” to measure two subwoofers.
For setting, perform steps 9 to 14 of “Set up
“Channel Select”” (vpage64).
5
8VHuiWRVHOHFW³$XWR6HWXS6WDUW´
DQGWKHQSUHVV
ENTER