Owner's Manual

113
Basic versionSimple version Information
ENGLISH
Advanced version
Erasing the code by each equipment input source
1
3UHVVDQGKROGPOWER ONDQG
ZONE/DEVICE ONIRUDWOHDVW
VHFRQGV
“SETUP” flashes twice on the remote
control unit.
2
8VHuiWRGLVSOD\³5(6(7´
RQWKHUHPRWHFRQWUROXQLWDQG
SUHVV
ENTER
3
:KHQ³/($51´DSSHDUVRQ
WKHUHPRWHFRQWUROXQLWSUHVV
ENTER
4
:KHQ³02'("´DSSHDUVRQWKH
UHPRWHFRQWUROXQLWSUHVVWKH
LQSXWVRXUFHVHOHFWEXWWRQRIWKH
$9HTXLSPHQWWKDW\RXZDQWWR
HUDVH
5
:KHQ³$//"´DSSHDUVSUHVVENTER
“RESET” flashes four times on the remote control unit and the
normal operation mode is restored.
Operating the main remote control unit
Operating macro function
• When the macro function is used, operations that usually require a
complicated series of multiple button operations can be performed
easily just by pressing the
MACRO button.
• This device can remember up to 3 macro functions.
• Each macro can record a maximum of 18 steps.
[Example] All system power on
q Turn the TV’s power on
↓
w Turn this unit’s power on
↓
e Switch this unit’s input source to DVD
↓
r Turn the DVD’s power on
n Recording macro operations
1
3UHVV DQG KROG POWER ON DQG ZONE/DEVICE ON
IRUDWOHDVWVHFRQGV
“SETUP” flashes twice on the remote control unit.
2
8VH ui WR GLVSOD\ ³0$&52´
RQ WKH UHPRWH FRQWURO XQLW DQG
SUHVV
ENTER
3
:KHQ³0&1R"´DSSHDUVRQWKH
UHPRWHFRQWUROXQLWSUHVVWKH
QUICK SELECTEXWWRQWKDW\RX
ZDQWWRVWRUH
Button Macro number
QUICK SELECT 1 MACRO-1
QUICK SELECT 2 MACRO-2
QUICK SELECT 3 MACRO-3
4
3UHVVWKHEXWWRQVWREHVWRUHGRQH
E\RQH
• The step number for the storing procedure and mode are alternately
displayed on the remote control unit.
• You cannot store the macros for the
ZONE SELECT, SOURCE
SELECT
and BACK LIGHT buttons.
5
3UHVVMACROWRH[LWWKHPDFURIXQFWLRQ
“SET” flashes four times on the remote control unit and the
normal operation mode is restored.
n Adjusting the interval time of macro operations
transmitting
The macro operation transmission interval can be adjusted.
• The factory setting is “0.5 sec”.
1
3UHVVDQGKROGPOWER ONDQG
ZONE/DEVICE ONIRUDWOHDVW
VHFRQGV
“SETUP” flashes twice on the remote
control unit.
2
8VHuiWRGLVSOD\³0$&52´
RQWKHUHPRWHFRQWUROXQLWDQG
SUHVV
ENTER
3
:KHQ³0&1R"´DSSHDUVRQWKH
UHPRWHFRQWUROXQLWSUHVVWKH
QUICK SELECTEXWWRQWKDW\RX
ZDQWWRVHW
Button Macro number
QUICK SELECT 1 MACRO-1
QUICK SELECT 2 MACRO-2
QUICK SELECT 3 MACRO-3
4
3UHVVMACROPDQ\WLPHVWRVHWWKHPDFURRSHUDWLRQ
WUDQVPLVVLRQLQWHUYDODQGSUHVV
ENTER
“SET” flashes four times on the remote control unit and the
normal operation mode is restored.
Remote control unit display
Time values that you can
set
0.25 0.25 sec
0.50 0.5 sec
0.75 0.75 sec
1.00 1 sec
1.25 1.25 sec