DENON AVR control protocol Ver.03 Application model : AVR-4520CI/AVR-4520 Application terminal: Ethernet RS-232C Rev 8.1.0 Connector specification .
RJ-45(10BASE-T/100BASE-TX) .
NETWORK SETUP of AVR-4520CI/AVR-4520 >Procedure of Network Setup mode. (1)Press SETUP MENU button, then Menu appears on FL-display(and GUI) (2)Select “Setup Menu > Network > Settings ” . (3)Set parameters described below. "On"---Use this setting when DHCP server is on the local network. "Off"---Use this setting when DHCP server is not on the local network. When sets "Off”, please set IP address. When sets "On”, you can confirm the IP address that is set by server.
Protocol specification The following three data forms are defined. COMMAND : The message sent to a system(AVR) from a controller(Touch Panel etc.) A command to a system is given from a controller. EVENT : The message sent to a controller (Touch Panel etc.) from a system (AVR) The result is sent, when a system is operated directly and a state changes. *The form of EVENT presupposes that it is the same as that of COMMAND. **Refer to the following table for the contents of COMMAND and EVENT.
The example of a command * is the meaning of 0x0D.
Others A) COMMAND is receivable also during transmission of EVENT. B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels returns as EVENT. C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case, the data of an intact channel is set to "50".
COMMAND and PARAMETER list PARAMETER function example ON POWER ON/STANDBY change PWON STANDBY PWSTANDBY ? Return PW Status PW? MV UP MASTER VOLUME UP/DOWN , direct change to **(**dB) MVUP DOWN MVDOWN **:00 to 98 by ASCII , 80=80(0dB), 00=-0(--dB)(MIN) ** MV80 ? Return MV Status MV? CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP FL DOWN ---FRONT Lch CVFL DOWN FL ** **:38 to 62 by ASCII , 50=0dB CVFL 50 FR UP CVFR UP FR DOWN ---FRONT Rch CVFR DOWN
PARAMETER function example SBR UP ---SURROUND BACK Rch (SBch 2SP) CVSBR UP SBR DOWN CVSBR DOWN SBR ** **:38 to 62 by ASCII , 50=0dB CVSBR 50 SB UP ---SURROUND BACKch (SBch 1SP) CVSB UP SB DOWN CVSB DOWN SB ** **:38 to 62 by ASCII , 50=0dB CVSB 50 FHL UP CVFHL UP FHL DOWN ---FRONT HEIGHT Lch CVFHL DOWN FHL ** **:38 to 62 by ASCII , 50=0dB CVFHL 50 FHR UP CVFHR UP FHR DOWN ---FRONT HEIGHT Rch CVFHR DOWN FHR ** **:38 to 62 by ASCII , 50=0dB CVFHR 50 FWL UP CVFWL
COMMAND SI ZM PARAMETER AUX3 AUX4 AUX5 AUX6 AUX7 HDRADIO NET PANDORA SIRIUSXM SPOTIFY LASTFM FLICKR FAVORITES IRADIO SERVER USB/IPOD USB IPD IRP FVP ? ON OFF ? function ---AUX3(Additional Source) ---AUX4(Additional Source) ---AUX5(Additional Source) ---AUX6(Additional Source) ---AUX7(Additional Source) ---HD RADIO(North America model Only) ---NETWORK (North America model Only) (North America model Only) (North America & Europe model Only) (Europe model Only) example SIAUX3 SIAUX4 SIAUX5 SIAU
COMMAND ZM SR PARAMETER FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE4 FAVORITE1 MEMORY FAVORITE2 MEMORY FAVORITE3 MEMORY FAVORITE4 MEMORY CD | USB/IPOD SOURCE ? function FAVORITE STATION 1-4 MODE SELECT FAVORITE STATION 1-4 MODE MEMORY example ZMFAVORITE1 ZMFAVORITE2 ZMFAVORITE3 ZMFAVORITE4 ZMFAVORITE1 MEMORY ZMFAVORITE2 MEMORY ZMFAVORITE3 MEMORY ZMFAVORITE4 MEMORY REC SELECT mode set , and select source ---The name of PARAMETER is the same as that of the time of SI COMMAND.
COMMAND SD DC SV SLP PARAMETER AUTO HDMI DIGITAL ANALOG EXT.
COMMAND MS PARAMETER MOVIE MUSIC GAME DIRECT PURE DIRECT STEREO STANDARD DOLBY DIGITAL DTS SUROUND MCH STEREO WIDE SCREEN SUPER STADIUM ROCK ARENA JAZZ CLUB CLASSIC CONCERT MONO MOVIE MATRIX VIDEO GAME VIRTUAL ? QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK1 MEMORY QUICK2 MEMORY QUICK3 MEMORY QUICK4 MEMORY QUICK5 MEMORY QUICK ? function Select SURROUND mode ---MULTI CH STEREO mode Return MS Status QUICK SELECT 1-5 MODE SELECT QUICK SELECT 1-5 MODE MEMORY Return MSQUICK Status - 12 - example MSMOVIE M
COMMAND VS PARAMETER ASPNRM ASPFUL ASP ? MONIAUTO MONI1 MONI2 MONI ? SC48P SC10I SC72P SC10P SC10P24 SC4K SCAUTO SC ? SCH48P SCH10I SCH72P SCH10P SCH10P24 SCH4K SCHAUTO SCH ? AUDIO AMP AUDIO TV AUDIO ? VPMAUTO VPMGAME VPMMOVI VPM ? VST ON VST OFF VST ? function Set Aspect Ratio to 4:3 mode Set Aspect Ratio to 16:9 mode Return VSASP Status Set HDMI MONITOR automatic detection Set HDMI MONITOR OUT-1 Set HDMI MONITOR OUT-2 Return VSMONI Status Set Resolution to 480p/576p Set Resolution to 1080i Set Resolutio
MODE: ? LOM ON LOM OFF LOM ? PHG LOW PHG MID PHG HI PHG ? SP:FH SP:FW SP:SB SP:HW SP:BH SP:BW SP:OFF SP: ? function PARAMETER setting TONE CONTROL ON/OFF Return PSTONE CONTROL Status CINEMA EQ. ON/OFF Return PSCINEMA EQ.Status CINEMA / MUSIC / GAME mode change (This parameter can change DOLBY PL2,PL2x,NEO:X mode.
COMMAND PS PARAMETER MULTEQ:AUDYSSEY MULTEQ:BYP.
PARAMETER function DSX ONHW Audyssey DSX ON(Heights & Wides) PSDSX DSX ONH Audyssey DSX ON(Heights) PSDSX DSX ONW Audyssey DSX ON(Wides) PSDSX DSX OFF Audyssey DSX OFF PSDSX DSX ? Return PSDSX Status PSDSX STW UP STAGE WIDTH UP/DOWN, direct change to **dB PSSTW STW DOWN **:00 to 99 by ASCII, 50=0dB PSSTW STW ** ---AVR-4520 can be operated from -10 to +10(40 to 60) PSSTW STW ? Return PSSTW Status PSSTW STH UP STAGE HEIGHT UP/DOWN , direct change to **dB PSSTH STH DOWN **:00 to 99 by ASCII , 50=0dB PSSTH STH
PARAMETER function BSC UP Bass Sync UP/DOWN , direct change to **dB PSBSC BSC DOWN **:00 to 99 by ASCII , 00=0 PSBSC BSC ** ---AVR-4520 can be operated from 0 to 16(50 to 66) PSBSC BSC ? Return PSBSC Status PSBSC DEH OFF Dialogue Enhancer direct change PSDEH DEH LOW PSDEH DEH MED PSDEH DEH HIGH PSDEH DEH ? Return PSDEH Status PSDEH LFE UP LFE UP/DOWN , direct change to **dB PSLEE LFE DOWN **:00 to 99 by ASCII , 00=0dB, 10=-10dB PSLFE LFE ** ---AVR-4520 can be operated from 0 to -10 PSLFE LFE ? Return PSLFE
PARAMETER function example PAN ON PANORAMA ON/OFF PSPAN ON PAN OFF PSPAN OFF PAN ? Return PSPAN Status PSPAN ? DIM UP DIMENSION UP/DOWN , direct change to **dB PSDIM UP DIM DOWN **:00 to 99 by ASCII , 00=0, PSDIM DOWN DIM ** --- AVR-4520 can be operated from 0 to 6 PSDIM ** DIM ? Return PSDIM Status PSDIM ? CEN UP CENTER WIDTH UP/DOWN , direct change to **dB PSCEN UP CEN DOWN **:00 to 99 by ASCII , 00=0 PSCEN DOWN CEN ** --- AVR-4520 can be operated from 0 to 7 PSCEN 07
COMMAND PS PARAMETER RSTR OFF RSTR MODE1 RSTR MODE2 RSTR MODE3 RSTR ? FRONT SPA FRONT SPB FRONT SPA+B FRONT? function AUDIO RESTORER direct change Return PSRSTR Status FRONT SPEAKER direct change Return PSFRONT Status - 19 - example PSRSTR OFF PSRSTR MODE1 PSRSTR MODE2 PSRSTR MODE3 PSRSTR ? PSFRONT SPA PSFRONT SPB PSFRONT A+B PSFRONT?
PARAMETER function OFF Picture Mode=OFF STD Picture Mode=STANDARD MOV Picture Mode=MOVIE VVD Picture Mode=VIVID STM Picture Mode=STREAM CTM Picture Mode=CUSTOM ? Return PSPV Status CN UP CONTRAST UP/DOWN , direct change to **dB CN DOWN **:44 to 56 by ASCII , 50=0 CN ** --- AVR-4520 can be operated from -6 to +6(44 to 56) CN ? Return PSCN Status BR UP BRIGHTNESS UP/DOWN , direct change to **dB BR DOWN **:00 to 12 by ASCII , 00=0 BR ** --- AVR-4520 can be operated from 0 to 12 BR ? Return PSBR Status CM UP CH
COMMAND Z2 PARAMETER PHONO | USB/IPOD USB IPD IRP FVP SOURCE UP DOWN ** ON OFF ? Z2MU ON OFF ? Z2CS ST MONO ? Z2CV FL UP FL DOWN FL ** FR UP FR DOWN FR ** ? Z2HPF ON OFF ? Z2 Z2CV COMMAND : "*" function ZONE2 mode set , and select source ---The name of PARAMETER is the same as that of the time of SI COMMAND.
PARAMETER function BAS UP ZONE2 BASS UP/DOWN , direct change to **dB BAS DOWN **:00 to 99 by ASCII , 00=0dB BAS ** ---AVR-4520 can be operated from -10 to +10(40 to 60) BAS ? Return Z2PSBAS Status TRE UP ZONE2 TREBLE UP/DOWN , direct change to **dB TRE DOWN **:00 to 99 by ASCII , 00=0dB TRE ** ---AVR-4520 can be operated from -10 to +10(40 to 60) TRE ? Return Z2PSTRE Status Z2SLP OFF ZONE2 SLEEP TIMER setting *** ***:001 to 120 by ASCII , 010=10min ? Return Z2SLP Status FAVORITE1 Z2 ZONE2 FAVORITE STATION 1
COMMAND Z3 PARAMETER PHONO | USB/IPOD USB IPD IRP FVP SOURCE UP DOWN ** ON OFF ? Z3MU ON OFF ? Z3CS ST MONO ? Z3CV FL UP FL DOWN FL ** FR UP FR DOWN FR ** ? Z3HPF ON OFF ? Z3 Z3CV COMMAND : "*" function ZONE3 mode set , and select source ---The name of PARAMETER is the same as that of the time of SI COMMAND.
PARAMETER function BAS UP ZONE3 BASS UP/DOWN , direct change to **dB BAS DOWN **:00 to 99 by ASCII , 00=0dB BAS ** ---AVR-4520 can be operated from -10 to +10(40 to 60) BAS ? Return Z3PSBAS Status TRE UP ZONE3 TREBLE UP/DOWN , direct change to **dB TRE DOWN **:00 to 99 by ASCII , 00=0dB TRE ** ---AVR-4520 can be operated from -10 to +10(40 to 60) TRE ? Return Z3PSTRE Status Z3SLP OFF ZONE3 SLEEP TIMER setting *** ***:001 to 120 by ASCII , 010=10min ? Return Z3SLP Status FAVORITE1 Z3 ZONE3 FAVORITE STATION 1
COMMAND Z4 Z4SLP PARAMETER DVD | SOURCE ON OFF ? OFF *** ? function ZONE4 mode set , and select source ---The name of PARAMETER is the same as that of the time of SI COMMAND that is assigned HDMI INPUT.
ANALOG TUNER(FM) Control function TUNER Frequency UP/DOWN --- ****.** MHz at FM band (<050000 is FM.) Return TF Status TUNER PRESET CH UP/DOWN , direct change to No.** ** 01-56 01=CH01,56=CH56 Return TP Status TUNER PRESET MEMORY TUNER PRESET MEMORY, Preset stored at No.** ** 01-56 01=CH01,56=CH56 Return TM Status ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode example TFANUP TFANDOWN TFAN008750 (87.
HD RADIO Control(AVR-4520CI North America model only) example TFHDUP TFHDDOWN TFHD105000 (1050.00kHz at AM) TFHDMC2 --- ****.** kHz at AM band (>050000 is AM.) ****.** MHz at FM band (<050000 is FM.) ---HD Multi Cast CH Select (* Multi Cast 1-8) ---Frequency and HD Multi Cast CH Select Return TFHD Status HD PRESET CH UP/DOWN , direct change to No.** ** 01-56 01=CH01,56=CH56 HD? HDUP HDDOWN HD** (PRESET No.
Network Audio/USB /iPod DIRECT Extended Control COMMAND NS PARAMETER 90 91 92 93 94 9A 9B 9C 9D 9E 9F 9G 9H 9I 9J 9K 9X 9Y 9Z NSA NSE NSD * 9W 9M function example “Cursor Up” Control NS90 “Cursor Down” Control NS91 “Cursor Left” Control NS92 “Cursor Right” Control NS93 “Enter (Play/Pause)” Control NS94 “Play” Control(iRadio/mServer/USB) NS9A “Play/Pause” Control(iPod Direct) “Pause” Control NS9B “Play/Pause” Control(iPod Direct) “Stop” Control NS9C “Skip Plus”
example NSB00 function Preset Call ** 00-55 00=CH01,55=CH56 Preset Memory, Preset stored at No.** ** 00-55 00=CH01,55=CH56 Return Preset Channel 01-56 status UTF-8 NSC00 - 29 - PARAMETER B** (PRESET No.) C** (PRESET No.
Cursor/Enter/Setup Menu COMMAND MN PARAMETER CUP CDN CLT CRT ENT RTN OPT INF MEN ON MEN OFF MEN? PRV ON PRV OFF PRV? ZST ON ZST OFF function “Cursor Up” Control “Cursor Down” Control “Cursor Left” Control “Cursor Right” Control “Enter” Control “RETURN” Control “OPTION” Control “INFO” Control “Setup Menu ON” Control “Setup Menu OFF” Control Return MNMEN(Menu) status “InstaPrevue ON” Control “InstaPrevue OFF” Control Return MNPRV(InstaPrevue) status “All Zone Stereo ON” Control “All Zone Stereo OFF” Control
Remote Lock/Panel Lock COMMAND SY PARAMETER REMOTE LOCK ON REMOTE LOCK OFF PANEL LOCK ON PANEL+V LOCK ON PANEL LOCK OFF function REMOTE CONTROL LOCK ON/OFF PANEL BUTTON (Except MASTER VOL.)CONTROL LOCK ON PANEL BUTTON & MASTER VOL. CONTROL LOCK ON PANEL BUTTUM & MASTER VOL.
EVENT(or RESPONSE) and PARAMETER list EVENT PW MV CV PARAMETER ON STANDBY ** function POWER ON/STANDBY change MASTER VOLUME change , **:00 to 98 by ASCII 98 = 18dB(MAX) 80 = 00dB 01 = -79dB 005 = -79.5dB 00 = ---(MIN) CHANNEL VOLUME change , **:00,38 to 62 by ASCII 62 = +12dB(MAX) 50 = 0dB 38 = -12dB(MIN) 00 = OFF (define ONLY SW&SW2ch in DIRECT mode.
EVENT SI PARAMETER PHONO CD TUNER DVD BD TV SAT/CBL MPLAY GAME AUX1 AUX2 AUX3 AUX4 AUX5 AUX6 AUX7 HDRADIO NET PANDORA SIRIUSXM SPOTIFY LASTFM FLICKR FAVORITES IRADIO SERVER USB/IPOD USB DIRECT IPOD DIRECT USB IPD IRP FVP function INPUT source change ---FM TUNER(Except North America model ) ---Blu-ray ---TV AUDIO ---CBL/SAT ---MEDIA PLAYER ---AUX1 ---AUX2 ---AUX3 (Additional Source) ---AUX4 (Additional Source) ---AUX5 (Additional Source) ---AUX6 (Additional Source) ---AUX7 (Additional Source) ---HD RADIO (
EVENT ZM SR SD DC PARAMETER ON OFF FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE4 FAVORITE1 MEMORY FAVORITE2 MEMORY FAVORITE3 MEMORY FAVORITE4 MEMORY PHONO | IPOD DIRECT SOURCE AUTO HDMI DIGITAL ANALOG EXT.IN ARC NO AUTO PCM DTS function MAIN ZONE ON/OFF change FAVORITE STATION 1-4 MODE SELECT FAVORITE STATION 1-4 MODE MEMORY REC SELECT source change ---The name of PARAMETER is the same as that of the time of SI COMMAND.
EVENT SV SLP PARAMETER DVD BD TV SAT/CBL MPLAY GAME AUX1 AUX2 AUX3 AUX4 AUX5 AUX6 AUX7 CD SOURCE OFF *** function VIDEO SELECT mode source change ---Blu-ray ---TV AUDIO ---CBL/SAT ---MEDIA PLAYER ---GAME ---AUX1 ---AUX2 ---AUX3(Additional Source) ---AUX4(Additional Source) ---AUX5(Additional Source) ---AUX6(Additional Source) ---AUX7(Additional Source) MAIN ZONE SLEEP TIMER setting change - 35 - example SVDVD SVBD SVTV SVSAT/CBL SVMPLAY SVGAME SVAUX1 SVAUX2 SVAUX3 S
EVENT MS PARAMETER DIRECT PURE DIRECT STEREO MULTI CH IN M CH IN+PL2X C M CH IN+PL2X M M CH IN+PL2Z H M CH IN +DOLBY EX MULTI CH IN 7.
EVENT MS PARAMETER DTS NEO:X C DTS NEO:X M DTS NEO:X G DTS SURROUND DTS ES DSCRT6.1 DTS ES MTRX6.1 DTS+PL2X C DTS+PL2X M DTS+PL2Z H DTS+NEO:X C DTS+NEO:X M DTS+NEO:X G DTS96/24 DTS96 ES MTRX MCH STEREO ROCK ARENA JAZZ CLUB MONO MOVIE MATRIX VIDEO GAME VIRTUAL DOLBY D+ DOLBY D+ +EX DOLBY D+ +PL2X C DOLBY D+ +PL2X M DOLBY D+ +PL2Z H DOLBY D+ +NEO:X C DOLBY D+ +NEO:X M DOLBY D+ +NEO:X C function - 37 - example MSDTS NEO:X C MSDTS NEO:X M MSDTS NEO:X G MSDTS SURROUND MSDTS ES DSCRT6.
EVENT PARAMETER DOLBY TRUEHD DOLBY HD DOLBY HD+EX DOLBY HD+PL2X C DOLBY HD+PL2X M DOLBY HD+PL2Z H DOLBY HD+NEO:X C DOLBY HD+NEO:X M DOLBY HD+NEO:X G DTS HD DTS HD MSTR DTS HD+PL2X C DTS HD+PL2X M DTS HD+PL2Z H DTS HD+NEO:X C DTS HD+NEO:X M DTS HD+NEO:X G DTS ES 8CH DSCRT DTS EXPRESS MPEG2 AAC AAC+DOLBY EX AAC+PL2X C AAC+PL2X M AAC+PL2Z H AAC+NEO:X C AAC+NEO:X M AAC+NEO:X G function (JAPAN (JAPAN (JAPAN (JAPAN (JAPAN (JAPAN (JAPAN (JAPAN model model model model model model model model Only) Only) Only)
EVENT MS PARAMETER AUDYSSEY DSX PL2X C DSX PL2X M DSX PL2X G DSX PL2 C DSX PL2 M DSX PL2 G DSX QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK0 function QUICK SELECT mode change ---QUICK 1(or 2, 3, 4, 5) Change QUICK SELECT OFF - 39 - example MSAUDYSSEY DSX MSPL2X C DSX MSPL2X M DSX MSPL2X G DSX MSPL2 C DSX MSPL2 M DSX MSPL2 G DSX MSQUICK1 MSQUICK2 MSQUICK3 MSQUICK4 MSQUICK5 MSQUICK0
EVENT VS PARAMETER MONIAUTO MONI1 MONI2 ASPNRM ASPFUL SC48P SC10I SC72P SC10P SC10P24 SC4K SCAUTO SCH48P SCH10I SCH72P SCH10P SCH10P24 SCH4K SCHAUTO AUDIO AMP AUDIO TV VPMAUTO VPMGAME VPMMOVI VST ON VST OFF function HDMI MONITOR setting change ASPECT setting change NRM=4:3 , FUL=16:9 Resolution(analog) setting change Resolution(HDMI) setting change HDMI AUDIO Output setting change AMP=AVR Video Mode setting change VERTICAL STRETCH setting change - 40 - example VSMONIAUTOCR> VSMONI1 VSMONI2 V
EVENT PS PARAMETER TONE CTRL OFF TONE CTRL ON CINEMA EQ.ON CINEMA EQ.OFF MODE:CINEMA MODE:MUSIC MODE:GAME MODE:HEIGHT LOM ON LOM OFF PHG LOW PHG MID PHG HI SP:FH SP:FW SP:SB SP:HW SP:BH SP:BW SP:OFF MULTEQ:AUDYSSEY MULTEQ:BYP.LR MULTEQ:FLAT MULTEQ:MANUAL MULTEQ:OFF DYNEQ ON DYNEQ OFF function TONE CONTROL ON/OFF change CINEMA EQ.
EVENT PS PARAMETER REFLEV 0 REFLEV 5 REFLEV 10 REFLEV 15 DYNVOL HEV DYNVOL MED DYNVOL LIT DYNVOL OFF LFC ON LFC OFF CNTAMT ** DSX ONHW DSX ONH DSX ONW DSX OFF STW ** STH ** BAS ** TRE ** BAS ** TRE ** DRC AUTO DRC LOW DRC MID DRC HI DRC OFF BSC ** DEH OFF DEH LOW DEH MED DEH HIGH function Reference Level Offset change DYNAMIC VOLUME change Audyssey LFC change Containment Amount change Audyssey DSX change STAGE WIDTH change STAGE HEIGHT change BASS change TREBLE change BASS change TREBLE change Dynamic
EVENT PS PARAMETER LFE ** LFL 00 LFL 05 LFL 10 LFL 15 EFF ON EFF OFF EFF ** DEL *** PAN ON PAN OFF DIM ** CEN ** CEG ** SWR ON SWR OFF RSZ S RSZ MS RSZ M RSZ ML RSZ L DELAY *** RSTR OFF RSTR MODE1 RSTR MODE2 RSTR MODE3 FRONT SPA FRONT SPB FRONT SPA+B function LFE change LFE Level change (When the Input Mode is “EXTERNAL IN” mode only) EFFECT ON/OFF change EFFECT LEVEL change DELAY change PANORAMA ON/OFF change DIMMENSION change CENTER WIDTH change CENTER GAIN change SW ON/OFF change ROOM SIZE change AUD
EVENT PV PARAMETER OFF STD MOV VVD STM CTM CN ** BR ** CM ** HUE ** DNR OFF DNR LOW DNR MID DNR HI ENH ** function Picture Mode=OFF Picture Mode=STANDARD Picture Mode=MOVIE Picture Mode=VIVID Picture Mode=STREAM Picture Mode=CUSTOM CONTRAST change BRIGHTNESS Change CROMA LEVEL change Hue Change DNR change ENHANCER change - 44 - example PVOFF PVSTD PVMOV PVVVD PVSTM PVCTM PVCN 50 PVBR 12 PVCM 50 PVHUE 50 PVDNR OFF PVDNR LOW PVDNR MID PVDNR HI PVENH
EVENT Z2 PARAMETER PHONO | USB DIRECT IPOD DIRECT SOURCE QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK0 FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE4 FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE4 ** Z2MU ON OFF ON OFF MEMORY MEMORY MEMORY MEMORY function ZONE2 source change ---The name of PARAMETER is the same as that of the time of SI COMMAND.
EVENT Z2CS Z2CV Z2HPF Z2PS PARAMETER ST MONO FL ** FR ** ON OFF BAS ** TRE ** function ZONE2 Channel setting **:38 to 62 by ASCII , 50=0dB **:38 to 62 by ASCII , 50=0dB ZONE2 HPF ON/OFF change ZONE2 BASS change ZONE2 TEBLE change - 46 - example Z2CSST Z2CSMONO Z2CVFL 50 Z2CVFR 50 Z2HPFON Z2HPFOFF Z2PSBAS 50 Z2PSTRE 50
EVENT Z3 PARAMETER PHONO | USB DIRECT IPOD DIRECT SOURCE QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK0 FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE4 FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE4 ** Z3MU ON OFF ON OFF MEMORY MEMORY MEMORY MEMORY function ZONE3 source change ---The name of PARAMETER is the same as that of the time of SI COMMAND.
EVENT Z3CS Z3CV Z3HPF Z3PS PARAMETER ST MONO FL ** FR ** ON OFF BAS ** TRE ** function ZONE3 Channel setting **:38 to 62 by ASCII , 50=0dB **:38 to 62 by ASCII , 50=0dB ZONE3 HPF ON/OFF change ZONE3 BASS change ZONE3 TEBLE change - 48 - example Z3CSST Z3CSMONO Z3CVFL 50 Z3CVFR 50 Z3HPFON Z3HPFOFF Z3PSBAS 50 Z3PSTRE 50
ANALOG TUNER Control PARAMETER AN****** (6 digits) TP AN**(PRESET No.) function TUNER Frequency change --- ****.** MHz at FM band TUNER PRESET change to No.** ** 01-56 01=CH01,56=CH56 Change Preset Channel select OFF TUNER PRESET MEMORY ** 01-56 01=CH01,56=CH56 ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode TPAN01 (PRESET No.”01”) TPANOFF TPANMEM01 ANOFF ANMEM** example TFAN008750 (87.
HD RADIO Control(AVR-4520CI North America model only) EVENT example TPHD105000 (1050.00kHz at AM) TFHDMC2 TPHD01 (PRESET No.”01”) TPHDOFF TPHDMEM01 TP TF function --- ****.** kHz at AM band (>050000 is AM.) ****.** MHz at FM band (<050000 is FM.) ---HD Multi Cast CH change (* Multi Cast 1-8, Analog 0) HD**(PRESET No.) HD RADIO PRESET change to No.
EVENT HD PARAMETER PTY(18 digits) ARTIST(40 digits) TITLE(40 digits) ALBUM(40 digits) GENRE(23 digits) MODE HD HD HD HD HD HD function PROGRAM TYPE change ARTIST NAME change TITLE NAME change ALBUM NAME change GANRE change MODE(ANALOG/DIGITAL) - 51 - example HDPTY (18 digits) HDARTIST (40 digits) HDTITLE (40 digits) HDALBUM (40 digits) HDGENRE (23 digits) HDMODE DIGITAL HDMODE ANALOG
Network Audio/USB /iPod DIRECT Extended Control EVENT PARAMETER NSA 0 1 2 3 4 5 6 7 8 function Onscreen Display Information is Answered By the NSA Command.
EVENT PARAMETER NSE 0 1 2 3 4 5 6 7 8 function Onscreen Display Information(mServer/iRadio) is Answered By the NSE Command.
function example NSB00 NSC00 - 54 - Preset Call ** 00-55 00=CH01,55=CH56 Preset Memory, Preset stored at No.** ** 00-55 00=CH01,55=CH56 Return Preset Channel CH1-CH56 status UTF-8 ** 00-55 00=CH01,55=CH56 PARAMETER B** (PRESET No.) C** (PRESET No.
Cursor/Enter/Setup Menu COMMAND MN PARAMETER MEN ON MEN OFF PRV ON PRV OFF ZST ON ZST OFF function “Setup Menu ON” Control “Setup Menu OFF” Control “InstaPrevue ON” Control “InstaPrevue OFF” Control “All Zone Stereo ON” Control “All Zone Stereo OFF” Control example MNMEN MNMEN MNPRV MNPRV MNZST MNZST ON OFF ON OFF ON OFF TRIGGER CONTROL EVENT TR 1 1 2 2 PARAMETER ON OFF ON OFF function Trigger Trigger Trigger Trigger 1 1 2 2 example TR1 TR1 TR2 TR2 ON OFF ON OFF ON OF
Extension COMMAND The RC code can be sent from Serial protocol commands Protocol specification Command structure: COMMAND + RC FORMAT + RC DATA + CR (0x0D) COMMAND : ASCII CODE of 2 characters Ex. RC : RC CODE RC FORMAT : ASCII CODE of 3 characters Ex. KSK : KASEIKYO FORMAT SHP : SHARP FORMAT RC DATA : ASCII CODE of 7 characters For details of the RC CODE , please refer to the IR remote control code list.
The example of a command * is the meaning of 0x0D.
