Upgrade Instructions

ManualsBrandsDenon ManualsSawAVR-3808CI

Denon Brand Company

D&M Building, 2-1 Nisshin-cho, Kawasaki-ku, Kawasaki-shi,

Kanagawa, 210-8569, Japan

Denon Electronics (USA), LLC.Denon Electronics (USA), LLC.

100 Corporate Drive, Mahwah, New Jersey 07430 USA

TEL: 201-762-6500 usa.denon.com

10/1/2008

AVR-4308CI / 3808CI

Upgrade New Feature

Instructions

Table of Contents

1. Before Updating

- Requirements --------------------------------------- P1

- Recommendations ------------------------------------- P1

- Key Notes on Network Environment Conguraitons - P1

- About System Setup Memory ------------------------- P1

2. Basic Operations ---------------------------------------- P2

3. Install New Feature ---------------------------------------- P3 - P5

4. After The Upgrade ---------------------------------------- P6

Summary of content (7 pages)

PAGE 1
AVR-4308CI / 3808CI Upgrade New Feature Instructions Table of Contents 1. Before Updating - Requirements --------------------------------------- P1 - Recommendations ------------------------------------- P1 - Key Notes on Network Environment Configuraitons - P1 - About System Setup Memory ------------------------- P1 2. Basic Operations ---------------------------------------- P2 3. Install New Feature ---------------------------------------- P3 - P5 4.
PAGE 2
1. Before Updating AVR-4308CI AVR-3808CI Requirements - Broadband Internet Access - Cable/DSL Modem - Network Router or Hub - Proper configuration of the Denon A/V component to work on a particular Network Environment - Ethernet ‘Straight’ Cable for Direct connection to the Network Environment Recommentations - If you did not install, or configure, the Denon A/V Component with your Network Environment, please contact your Network Installer/Integrator to assist.
PAGE 3
2. Basic Operations AVR-4308CI AVR-3808CI Basic Operations Highlight Cursor Menu Icon Selectable Item Text guidance On-Screen Interactive Display A/V Receiver (shown 4308CI) 'MENU Key' : Show On-Screen Interactive Display 'ENTER Key' : Select 'Cursor Keys' : Move Highlight Cursor NOTE: Be sure 'AMP key' is flashing, and that the Front Panel remote is in "Main Zone" mode, see the Remote Control following instruction manual section "Remote ControlUnit Operations".
PAGE 4
3. Install New Feature (1/3) AVR-4308CI AVR-3808CI 1. Select "Manual Setup" - Press the ‘Menu’ key on the remote control or on the Front Panel of the AVR. - Pressing the ‘Down Cursor’ key, highlight the icon (shown as a pair of pliers, a screwdriver and a wrench) for “Manual Setup” - Press the ‘Right Cursor’ key to enter “Manual Setup” On-Screen Interactive Display Front Panel Display 2.
PAGE 5
3. Install New Feature (2/3) AVR-4308CI AVR-3808CI 4. Check "New Feature List" - With the "Upgrade" button highlighted, press the ‘Enter’ key to Execute the Upgrade Process Front Panel Display On-Screen Interactive Display 5. Confirming Upgrade - With the "Yes" button highlighted, press the 'Enter' key to execute the update. - If you do not wish to proceed with the update, press the 'Right Cursor' key to highlight the "No" button, then press the 'Enter' key to exit the update procedure.
PAGE 6
3. Install New Feature (3/3) AVR-4308CI AVR-3808CI 7. Firmware Upgrade is In Progress - Unit goes into update mode. - The 'Standby' power indicator will go "Red" and the On Screen Interface will turn off. - Update process information can be seen on the Front Panel Display. Power indicator will go RED 8. Complete Upgrade - Unit will automatically complete process and repower itself 'On'. - The "Standby Power" indicator will turn green. Power indicator will go Green 9.
PAGE 7
4. After The Upgrade AVR-4308CI AVR-3808CI Perform Audyssey MultEQ System Calibration - Once the Upgrade Feature Pack has been successfully downloaded and installed, you will need to perform the Audyssey MultEQ System Calibration Setup again. - Previous calibration settings have been erased as part of the upgrade. This is required due to the new Audyssey Features (Dynamic Volume and EQ) that were added as part of the upgrade. - No other settings in your System Setup have been changed or deleted.