DENON AVR control protocol Ver.04 Application model : AVR-3313CI/AVR-3313 Application terminal: Ethernet RS-232C Rev 8.7.0 Connector specification Page P1, P9,P30 -1- .
RJ-45(10BASE-T/100BASE-TX) .
NETWORK SETUP of AVR-3313CI/AVR-3313 >Procedure of Network Setup mode. (1)Press SETUP MENU button, then Menu appears on FL-display(and GUI) (2)Select “Setup Menu > Network > Settings ” . (3)Set parameters described below. "ON"---Use this setting when DHCP server is on the local network. "OFF"---Use this setting when DHCP server is not on the local network. When sets "OFF”, please set IP address. When sets "ON”, you can confirm the IP address that is set by server.
Protocol specification The following three data forms are defined. COMMAND : The message sent to a system(AVR) from a controller(Touch Panel etc.) A command to a system is given from a controller. EVENT : The message sent to a controller (Touch Panel etc.) from a system (AVR) The result is sent, when a system is operated directly and a state changes. *The form of EVENT presupposes that it is the same as that of COMMAND. **Refer to the following table for the contents of COMMAND and EVENT.
The example of a command * is the meaning of 0x0D.
Others A) COMMAND is receivable also during transmission of EVENT. B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels returns as EVENT. C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case, the data of an intact channel is set to "50".
COMMAND and PARAMETER list PARAMETER function example ON POWER ON/STANDBY change PWON STANDBY PWSTANDBY ? Return PW Status PW? MV UP MASTER VOLUME UP/DOWN , direct change to **(**dB) MVUP DOWN MVDOWN **:00 to 98 by ASCII , 80=80(0dB), 00=-0(--dB)(MIN) ** MV80 ? Return MV Status MV? CV FL UP CHANNEL VOLUME UP/DOWN , direct change to **dB CVFL UP FL DOWN ---FRONT Lch CVFL DOWN FL ** **:38 to 62 by ASCII , 50=0dB CVFL 50 FR UP CVFR UP FR DOWN ---FRONT Rch CVFR DOWN
PARAMETER function example SB UP ---SURROUND BACKch (SBch 1SP) CVSB UP SB DOWN CVSB DOWN SB ** **:38 to 62 by ASCII , 50=0dB CVSB 50 FHL UP CVFHL UP FHL DOWN ---FRONT HEIGHT Lch CVFHL DOWN FHL ** **:38 to 62 by ASCII , 50=0dB CVFHL 50 FHR UP CVFHR UP FHR DOWN ---FRONT HEIGHT Rch CVFHR DOWN FHR ** **:38 to 62 by ASCII , 50=0dB CVFHR 50 FWL UP CVFWL UP FWL DOWN ---FRONT WIDE Lch CVFWL DOWN FWL ** **:38 to 62 by ASCII , 50=0dB CVFWL 50 FWR UP CVFWR UP FWR DOW
COMMAND SI ZM SR PARAMETER PANDORA SIRIUSXM SPOTIFY LASTFM FLICKR FAVORITES IRADIO SERVER USB/IPOD USB IPD IRP FVP ? ON OFF ? FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE4 FAVORITE1 MEMORY FAVORITE2 MEMORY FAVORITE3 MEMORY FAVORITE4 MEMORY CD | USB/IPOD SOURCE ? function (North America model Only) (North America model Only) (North America & Europe model Only) (Europe model Only) example SIPANDORA SISIRIUSXM SISPOTIFY SILASTFM SIFLICKR SIFAVORITES SIIRADIO SISERVER Select iPod/
COMMAND SD DC SV SLP PARAMETER AUTO HDMI DIGITAL ANALOG ? AUTO PCM DTS ? DVD BD TV SAT/CBL MPLAY GAME AUX1 AUX2 CD SOURCE ? OFF *** ? function set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG) set force HDMI INPUT mode set force DIGITAL INPUT (Optical,Coaxial)mode set force ANALOG INPUT mode Return SD Status set DIGITAL INPUT AUTO mode set DIGITAL INPUT force PCM mode set DIGITAL INPUT force DTS mode Return DC Status VIDEO SELECT mode set , and select source ---Blu-ray ---TV AUDIO ---CBL/SAT ---MediaPlaye
COMMAND MS PARAMETER MOVIE MUSIC GAME DIRECT PURE DIRECT STEREO STANDARD DOLBY DIGITAL DTS SUROUND MCH STEREO ROCK ARENA JAZZ CLUB MONO MOVIE MATRIX VIDEO GAME VIRTUAL ? QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK1 MEMORY QUICK2 MEMORY QUICK3 MEMORY QUICK4 MEMORY QUICK5 MEMORY QUICK ? function Select SURROUND mode ---MULTI CH STEREO mode Return MS Status QUICK SELECT 1-5 MODE SELECT QUICK SELECT 1-5 MODE MEMORY Return MSQUICK Status - 11 - example MSMOVIE MSMUSIC MSGAME MSDIRECT MSPURE
COMMAND VS PARAMETER ASPNRM ASPFUL ASP ? MONIAUTO MONI1 MONI2 MONI ? SC48P SC10I SC72P SC10P SC10P24 SC4K SCAUTO SC ? SCH48P SCH10I SCH72P SCH10P SCH10P24 SCH4K SCHAUTO SCH ? AUDIO AMP AUDIO TV AUDIO ? VPMAUTO VPMGAME VPMMOVI VPM ? function Set Aspect Ratio to 4:3 mode Set Aspect Ratio to 16:9 mode Return VSASP Status Set HDMI MONITOR automatic detection Set HDMI MONITOR OUT-1 Set HDMI MONITOR OUT-2 Return VSMONI Status Set Resolution to 480p/576p Set Resolution to 1080i Set Resolution to 720p Set Resolut
MODE: ? LOM ON LOM OFF LOM ? FH:ON FH:OFF FH: ? PHG LOW PHG MID PHG HI PHG ? SP:FH SP:FW SP:SB SP:OFF SP: ? function PARAMETER setting TONE CONTROL ON/OFF Return PSTONE CONTROL Status SURROUND BACK SP MODE set Return PSSB: Status CINEMA EQ. ON/OFF Return PSCINEMA EQ.Status CINEMA / MUSIC / GAME / PL mode change (This parameter can change DOLBY PL2,PL2x,NEO:6 mode.
COMMAND PS PARAMETER MULTEQ:AUDYSSEY MULTEQ:BYP.
PARAMETER function BAS UP BASS UP/DOWN , direct change to **dB PSBAS BAS DOWN **:00 to 99 by ASCII , 50=0dB PSBAS BAS ** ---AVR-3313 can be operated from -6 to +6(44 to 56) PSBAS BAS ? Return PSBAS Status PSBAS TRE UP TREBLE UP/DOWN , direct change to **dB PSTRE TRE DOWN **:00 to 99 by ASCII , 50=0dB PSTRE TRE ** ---AVR-3313 can be operated from -6 to +6(44 to 56) PSTRE TRE ? Return PSTRE Status PSTRE DRC AUTO Dynamic Compression direct change PSDRC DRC LOW PSDRC DRC MID PSDRC DRC HI PSDRC DRC OFF PSDRC DRC
PARAMETER function example PAN ON PANORAMA ON/OFF PSPAN ON PAN OFF PSPAN OFF PAN ? Return PSPAN Status PSPAN ? DIM UP DIMENSION UP/DOWN , direct change to **dB PSDIM UP DIM DOWN **:00 to 99 by ASCII , 00=0, PSDIM DOWN DIM ** --- AVR-3313 can be operated from 0 to 6 PSDIM ** DIM ? Return PSDIM Status PSDIM ? CEN UP CENTER WIDTH UP/DOWN , direct change to **dB PSCEN UP CEN DOWN **:00 to 99 by ASCII , 00=0 PSCEN DOWN CEN ** --- AVR-3313 can be operated from 0 to 7 PSCEN 07
COMMAND PS PARAMETER RSTR OFF RSTR MODE1 RSTR MODE2 RSTR MODE3 RSTR ? FRONT SPA FRONT SPB FRONT SPA+B FRONT? function AUDIO RESTORER direct change Return PSRSTR Status FRONT SPEAKER direct change Return PSFRONT Status - 17 - example PSRSTR OFF PSRSTR MODE1 PSRSTR MODE2 PSRSTR MODE3 PSRSTR ? PSFRONT SPA PSFRONT SPB PSFRONT A+B PSFRONT?
PARAMETER function CN UP CONTRAST UP/DOWN , direct change to **dB CN DOWN **:44 to 56 by ASCII , 50=0 CN ** --- AVR-3313 can be operated from -6 to +6(44 to 56) CN ? Return PSCN Status BR UP BRIGHTNESS UP/DOWN , direct change to **dB BR DOWN **:00 to 12 by ASCII , 00=0 BR ** --- AVR-3313 can be operated from 0 to 12 BR ? Return PSBR Status CM UP CHROMA LEVEL UP/DOWN , direct change to **dB CM DOWN **:44 to 56 by ASCII , 50=0 CM ** --- AVR-3313 can be operated from -6 to +6(44 to 56) CM ? Return PSCN Status
COMMAND Z2 PARAMETER PHONO | USB/IPOD USB IPD IRP FVP SOURCE UP DOWN ** ON OFF ? Z2MU ON OFF ? Z2CS ST MONO ? Z2CV FL UP FL DOWN FL ** FR UP FR DOWN FR ** ? Z2HPF ON OFF ? Z2 Z2CV COMMAND : "*" function ZONE2 mode set , and select source ---The name of PARAMETER is the same as that of the time of SI COMMAND.
PARAMETER function BAS UP ZONE2 BASS UP/DOWN , direct change to **dB BAS DOWN **:00 to 99 by ASCII , 00=0dB BAS ** ---AVR-3313 can be operated from -10 to +10(40 to 60) BAS ? Return Z2PSBAS Status TRE UP ZONE2 TREBLE UP/DOWN , direct change to **dB TRE DOWN **:00 to 99 by ASCII , 00=0dB TRE ** ---AVR-3313 can be operated from -10 to +10(40 to 60) TRE ? Return Z2PSTRE Status Z2SLP OFF ZONE2 SLEEP TIMER setting *** ***:001 to 120 by ASCII , 010=10min ? Return SLP Status FAVORITE1 Z2 ZONE2 FAVORITE STATION 1-4
COMMAND Z3 PARAMETER PHONO | USB/IPOD USB IPD IRP FVP SOURCE UP DOWN ** ON OFF ? Z3MU ON OFF ? Z3CS ST MONO ? Z3CV FL UP FL DOWN FL ** FR UP FR DOWN FR ** ? Z3HPF ON OFF ? Z3 Z3CV COMMAND : "*" function ZONE3 mode set , and select source ---The name of PARAMETER is the same as that of the time of SI COMMAND.
PARAMETER function BAS UP ZONE3 BASS UP/DOWN , direct change to **dB BAS DOWN **:00 to 99 by ASCII , 00=0dB BAS ** ---AVR-3313 can be operated from -10 to +10(40 to 60) BAS ? Return Z3PSBAS Status TRE UP ZONE3 TREBLE UP/DOWN , direct change to **dB TRE DOWN **:00 to 99 by ASCII , 00=0dB TRE ** ---AVR-3313 can be operated from -10 to +10(40 to 60) TRE ? Return Z3PSTRE Status Z3SLP OFF ZONE3 SLEEP TIMER setting *** ***:001 to 120 by ASCII , 010=10min ? Return SLP Status FAVORITE1 Z3 ZONE3 FAVORITE STATION 1-4
ANALOG TUNER(FM) Control function TUNER Frequency UP/DOWN --- ****.** MHz at FM band (<050000 is FM.) Return TF Status TUNER PRESET CH UP/DOWN , direct change to No.** ** 01-56 01=CH01,56=CH56 Return TP Status TUNER PRESET MEMORY TUNER PRESET MEMORY, Preset stored at No.** ** 01-56 01=CH01,56=CH56 Return TM Status ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode example TFANUP TFANDOWN TFAN008750 (87.
HD RADIO Control(AVR-3313CI North America model only) example TFHDUP TFHDDOWN TFHD105000 (1050.00kHz at AM) TFHDMC2 --- ****.** kHz at AM band (>050000 is AM.) ****.** MHz at FM band (<050000 is FM.) ---HD Multi Cast CH Select (* Multi Cast 1-8) ---Frequency and HD Multi Cast CH Select Return TFHD Status HD PRESET CH UP/DOWN , direct change to No.** ** 01-56 01=CH01,56=CH56 HD? HDUP HDDOWN HD** (PRESET No.
Network Audio/USB /iPod DIRECT Extended Control COMMAND NS PARAMETER 90 91 92 93 94 9A 9B 9C 9D 9E 9H 9I 9J 9K example NS90 NS91 NS92 NS93 NS94 NS9A NS9B NS9C NS9D NS9E NS9H NS9I NS9J NS9K NS9M 9M function “Cursor Up” Control “Cursor Down” Control “Cursor Left” Control “Cursor Right” Control “Enter (Play/Pause)” Control “Play” Control(iRadio/mServer/USB) “Play/Pause” Control(iPod Direct) “Pause” Control “Play/Pause” Control(iPod Direct) “Sto
example NSB00 function Preset Call ** 00-55 00=CH01,55=CH56 Preset Memory, Preset stored at No.** ** 00-55 00=CH01,55=CH56 Return Preset Channel 01-56 status UTF-8 NSC00 - 26 - PARAMETER B** (PRESET No.) C** (PRESET No.
Cursor/Enter/Setup Menu COMMAND MN PARAMETER CUP CDN CLT CRT ENT RTN OPT INF MEN ON MEN OFF function “Cursor Up” Control “Cursor Down” Control “Cursor Left” Control “Cursor Right” Control “Enter” Control “RETURN” Control “OPTION” Control “INFO” Control “Setup Menu ON” Control “Setup Menu OFF” Control example MNCUP MNCDN MNCLT MNCRT MNENT MNRTN MNOPT MNINF MNMEN ON MNMEN OFF TRIGGER CONTROL COMMAND TR 1 1 2 2 PARAMETER ON OFF ON OFF function example TR1 TR1 TR2
Remote Lock/Panel Lock COMMAND SY PARAMETER REMOTE LOCK ON REMOTE LOCK OFF PANEL LOCK ON PANEL+V LOCK ON PANEL LOCK OFF function REMOTE CONTROL LOCK ON/OFF PANEL BUTTON (Except MASTER VOL.)CONTROL LOCK ON PANEL BUTTON & MASTER VOL. CONTROL LOCK ON PANEL BUTTUM & MASTER VOL.
EVENT(or RESPONSE) and PARAMETER list EVENT PW MV CV PARAMETER ON STANDBY ** function POWER ON/STANDBY change MASTER VOLUME change , **:00 to 98 by ASCII 98 = 18dB(MAX) 80 = 00dB 01 = -79dB 005 = -79.5dB 00 = ---(MIN) CHANNEL VOLUME change , **:00,38 to 62 by ASCII 62 = +12dB(MAX) 50 = 0dB 38 = -12dB(MIN) 00 = OFF (define ONLY SWch in DIRECT mode.
EVENT SI PARAMETER PHONO CD TUNER DVD BD TV SAT/CBL MPLAY GAME AUX1 AUX2 HDRADIO NET PANDORA SIRIUSXM SPOTIFY LASTFM FLICKR FAVORITES IRADIO SERVER USB/IPOD USB DIRECT IPOD DIRECT USB IPD IRP FVP function INPUT source change ---FM TUNER(Except North America model ) ---Blu-ray ---TV AUDIO ---CBL/SAT ---MEDIA PLAYER ---AUX1 ---AUX2 ---HD RADIO (North America model Only) ---NETWORK (North America model Only) (North America model Only) (North America & Europe model Only) (Europe model Only) ---iPod/USB - 30
EVENT ZM SR SD DC SV SLP PARAMETER ON OFF FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE4 FAVORITE1 MEMORY FAVORITE2 MEMORY FAVORITE3 MEMORY FAVORITE4 MEMORY PHONO | IPOD DIRECT SOURCE AUTO HDMI DIGITAL ANALOG ARC NO AUTO PCM DTS DVD BD TV SAT/CBL MPLAY GAME AUX1 AUX2 SOURCE OFF *** function MAIN ZONE ON/OFF change FAVORITE STATION 1-4 MODE SELECT FAVORITE STATION 1-4 MODE MEMORY REC SELECT source change ---The name of PARAMETER is the same as that of the time of SI COMMAND.
EVENT MS PARAMETER DIRECT PURE DIRECT STEREO MULTI CH IN M CH IN+PL2X C M CH IN+PL2X M M CH IN+PL2Z H M CH IN +DOLBY EX MULTI CH IN 7.1 DOLBY PRO LOGIC DOLBY PL2 C DOLBY PL2 M DOLBY PL2 G DOLBY PL2X C DOLBY PL2X M DOLBY PL2X G DOLBY PL2Z H DOLBY DIGITAL DOLBY D EX DOLBY D +PL2X C DOLBY D +PL2X M DOLBY D +PL2Z H DTS NEO:6 C DTS NEO:6 M DTS SURROUND DTS ES DSCRT6.1 DTS ES MTRX6.
EVENT PARAMETER DTS+NEO:6 DTS96/24 DTS96 ES MTRX MCH STEREO ROCK ARENA JAZZ CLUB MONO MOVIE MATRIX VIDEO GAME VIRTUAL DOLBY D+ DOLBY D+ +EX DOLBY D+ +PL2X C DOLBY D+ +PL2X M DOLBY D+ +PL2Z H DOLBY TRUEHD DOLBY HD DOLBY HD+EX DOLBY HD+PL2X C DOLBY HD+PL2X M DOLBY HD+PL2Z H DTS HD DTS HD MSTR DTS HD+NEO:6 DTS HD+PL2X C DTS HD+PL2X M DTS HD+PL2Z H DTS ES 8CH DSCRT DTS EXPRESS MPEG2 AAC AAC+DOLBY EX AAC+PL2X C AAC+PL2X M AAC+PL2Z H function (JAPAN (JAPAN (JAPAN (JAPAN (JAPAN model model model model model O
EVENT MS PARAMETER AUDYSSEY DSX PL DSX PL2 C DSX PL2 M DSX PL2 G DSX NEO:6 C DSX NEO:6 M DSX QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK0 function QUICK SELECT mode change ---QUICK 1(or 2, 3, 4, 5) Change QUICK SELECT OFF - 34 - example MSAUDYSSEY DSX MSPL DSX MSPL2 C DSX MSPL2 M DSX MSPL2 G DSX MSNEO:6 C DSX MSNEO:6 M DSX MSQUICK1 MSQUICK2 MSQUICK3 MSQUICK4 MSQUICK5 MSQUICK0
EVENT VS PARAMETER MONIAUTO MONI1 MONI2 ASPNRM ASPFUL SC48P SC10I SC72P SC10P SC10P24 SC4K SCAUTO SCH48P SCH10I SCH72P SCH10P SCH10P24 SCH4K SCHAUTO AUDIO AMP AUDIO TV VPMAUTO VPMGAME VPMMOVI function HDMI MONITOR setting change ASPECT setting change NRM=4:3 , FUL=16:9 Resolution(analog) setting change Resolution(HDMI) setting change HDMI AUDIO Output setting change Video Mode setting change - 35 - example VS MONIAUTO VSMONI1 VSMONI2 VSASPNRM VSASPFUL VSSC48P VSSC10I VSSC7
EVENT PS PARAMETER TONE CTRL OFF TONE CTRL ON SB:MTRX ON SB:PL2X CINEMA SB:PL2X MUSIC SB:ON SB:OFF SB:ESMTRX CINEMA EQ.ON CINEMA EQ.OFF MODE:CINEMA MODE:MUSIC MODE:GAME MODE:PRO LOGIC MODE:HEIGHT LOM ON LOM OFF FH:ON FH:OFF PHG LOW PHG MID PHG HI MULTEQ:AUDYSSEY MULTEQ:BYP.LR MULTEQ:FLAT MULTEQ:MANUAL MULTEQ:OFF DYNEQ ON DYNEQ OFF function TONE CONTROL ON/OFF change SURROUND BACK MODE change CINEMA EQ.
EVENT PS PARAMETER REFLEV 0 REFLEV 5 REFLEV 10 REFLEV 15 DYNVOL HEV DYNVOL MED DYNVOL LIT DYNVOL OFF DSX ONH DSX ONW DSX OFF STW ** STH ** BAS ** TRE ** BAS ** TRE ** DRC AUTO DRC LOW DRC MID DRC HI DRC OFF LFE ** EFF ** DEL *** function Reference Level Offset change DYNAMIC VOLUME change Audyssey DSX change STAGE WIDTH change STAGE HEIGHT change BASS change TREBLE change BASS change TREBLE change Dynamic Compression change When the input signal is Dolby TrueHD LFE change EFFECT LEVEL change DELAY cha
EVENT PS PARAMETER PAN ON PAN OFF DIM ** CEN ** CEI ** SWR ON SWR OFF RSZ S RSZ MS RSZ M RSZ ML RSZ L DELAY *** RSTR OFF RSTR MODE1 RSTR MODE2 RSTR MODE3 FRONT SPA FRONT SPB FRONT SPA+B function PANORAMA ON/OFF change DIMMENSION change CENTER WIDTH change CENTER IMAGE change SW ON/OFF change ROOM SIZE change AUDIO DELAY change AUDIO RESTORER change FRONT SPEAKER direct change - 38 - example PSPAN ON PSPAN OFF PSDIM 06 PSCEN 07 PSCEI 10 PSSWR ON PSSWR OFF PSRSZ S PSRSZ M
EVENT PV PARAMETER CN ** BR ** CM ** HUE ** DNR OFF DNR LOW DNR MID DNR HI ENH ** function CONTRAST change BRIGHTNESS Change CROMA LEVEL change Hue Change DNR change ENHANCER change - 39 - example PVCN 50 PVBR 12 PVCM 50 PVHUE 50 PVDNR OFF PVDNR LOW PVDNR MID PVDNR HI PVENH 12
EVENT Z2 PARAMETER CD | USB DIRECT IPOD DIRECT SOURCE QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK0 FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE4 FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE4 ** Z2MU ON OFF ON OFF MEMORY MEMORY MEMORY MEMORY function ZONE2 source change ---The name of PARAMETER is the same as that of the time of SI COMMAND.
EVENT Z2CS Z2CV Z2HPF Z2PS PARAMETER ST MONO FL ** FR ** ON OFF BAS ** TRE ** function ZONE2 Channel setting **:38 to 62 by ASCII , 50=0dB **:38 to 62 by ASCII , 50=0dB ZONE2 HPF ON/OFF change ZONE2 BASS change ZONE2 TEBLE change - 41 - example Z2CSST Z2CSMONO Z2CVFL 50 Z2CVFR 50 Z2HPFON Z2HPFOFF Z2PSBAS 50 Z2PSTRE 50
EVENT Z3 PARAMETER CD | USB DIRECT IPOD DIRECT SOURCE QUICK1 QUICK2 QUICK3 QUICK4 QUICK5 QUICK0 FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE4 FAVORITE1 FAVORITE2 FAVORITE3 FAVORITE4 ** Z3MU ON OFF ON OFF MEMORY MEMORY MEMORY MEMORY function ZONE3 source change ---The name of PARAMETER is the same as that of the time of SI COMMAND.
EVENT Z3CS Z3CV Z3HPF Z3PS PARAMETER ST MONO FL ** FR ** ON OFF BAS ** TRE ** function ZONE3 Channel setting **:38 to 62 by ASCII , 50=0dB **:38 to 62 by ASCII , 50=0dB ZONE3 HPF ON/OFF change ZONE3 BASS change ZONE3 TEBLE change - 43 - example Z3CSST Z3CSMONO Z3CVFL 50 Z3CVFR 50 Z3HPFON Z3HPFOFF Z3PSBAS 50 Z3PSTRE 50
ANALOG TUNER Control AN**(PRESET No.) function TUNER Frequency change --- ****.** kHz at AM band ****.** MHz at FM band TUNER PRESET change to No.** ** 01-56 01=CH01,56=CH56 Change Preset Channel select OFF TUNER PRESET MEMORY ** 01-56 01=CH01,56=CH56 ---Tuning mode set to AUTO mode ---Tuning mode set to MANUAL mode (1050.00kHz at AM) TPAN01 (PRESET No.
HD RADIO Control(AVR-3313CI North America model only) EVENT example TPHD105000 (1050.00kHz at AM) TFHDMC2 TPHD01 (PRESET No.”01”) TPHDOFF TPHDMEM01 TP TF function --- ****.** kHz at AM band (>050000 is AM.) ****.** MHz at FM band (<050000 is FM.) ---HD Multi Cast CH change (* Multi Cast 1-8, Analog 0) HD**(PRESET No.) HD RADIO PRESET change to No.
EVENT HD PARAMETER PTY(18 digits) ARTIST(40 digits) TITLE(40 digits) ALBUM(40 digits) GENRE(23 digits) MODE HD HD HD HD HD HD function PROGRAM TYPE change ARTIST NAME change TITLE NAME change ALBUM NAME change GANRE change MODE(ANALOG/DIGITAL) - 46 - example HDPTY (18 digits) HDARTIST (40 digits) HDTITLE (40 digits) HDALBUM (40 digits) HDGENRE (23 digits) HDMODE DIGITAL HDMODE ANALOG
Network Audio/USB /iPod DIRECT Extended Control EVENT PARAMETER NSA 0 1 2 3 4 5 6 7 8 function Onscreen Display Information is Answered By the NSA Command.
EVENT PARAMETER NSE 0 1 2 3 4 5 6 7 8 function Onscreen Display Information(mServer/iRadio) is Answered By the NSE Command.
function example NSB00 NSC00 - 49 - Preset Call ** 00-55 00=CH01,55=CH56 Preset Memory, Preset stored at No.** ** 00-55 00=CH01,55=CH56 Return Preset Channel CH1-CH56 status UTF-8 ** 00-55 00=CH01,55=CH56 PARAMETER B** (PRESET No.) C** (PRESET No.
TRIGGER CONTROL EVENT TR 1 1 2 2 PARAMETER ON OFF ON OFF function Trigger Trigger Trigger Trigger 1 1 2 2 example TR1 TR1 TR2 TR2 ON OFF ON OFF ON OFF ON OFF Remote Lock/Panel Lock EVENT SY PARAMETER REMOTE LOCK ON REMOTE LOCK OFF PANEL LOCK ON PANEL+V LOCK ON PANEL LOCK OFF function REMOTE CONTROL LOCK ON/OFF PANEL BUTTON(Except MASTER VOL.)CONTROL LOCK ON PANEL BUTTON & MASTER VOL. CONTROL LOCK ON PANEL BUTTUM & MASTER VOL.
Extension COMMAND The RC code can be sent from Serial protocol commands Protocol specification Command structure: COMMAND + RC FORMAT + RC DATA + CR (0x0D) COMMAND : ASCII CODE of 2 characters Ex. RC : RC CODE RC FORMAT : ASCII CODE of 3 characters Ex. KSK : KASEIKYO FORMAT SHP : SHARP FORMAT RC DATA : ASCII CODE of 7 characters For details of the RC CODE , please refer to the IR remote control code list.
The example of a command * is the meaning of 0x0D.
