Owner's Manual

8
ENGLISH
Set up speakers (Audyssey
®
Auto Setup)
STEP 1
Preparation
• In STEP 3, you will perform measurements at
multiple positions (two to eight positions) other
than the main listening position.
• You can achieve a more effective correction of
distortion within the listening area by performing
measurements at multiple positions.
9
0RYH WKH VHWXS PLFURSKRQH WR
SRVLWLRQ  XVH
ui WR VHOHFW
³0HDVXUH´DQGWKHQSUHVV
ENTER
The measurement of the second position
starts. Measurements can be made in up to
eight positions.
>@
67(30HDVXUHPHQW
3OHDVHSODFHWKHPLF
URSKRQHDWHDUKHLJKW
DWQGOLVWHQLQJ
SRVL LRQ
6WDUWQH[WPHDVXUHPHQW7HVW7RQHZLOOVWDUW
$8726(783
$8'<66(<$8726(783
(17(5 (QWHU 5(7851 &DQFHO
0HDVXUH
1H[W&DOFXODWLRQ
0XOW(4;7
If you want to omit measurements from the next
position onward, select “Next 1 Calculation”.
(Go to
STEP4 Calculation
)
10
5HSHDWVWHSPHDVXULQJSRVLWLRQV
WR
When measurement of position 8 is
completed, a “Measurements finished.”
message is displayed.
>@
67(30HDVXUHPHQW
0HDVXUHPHQWVILQLVKHG
3URFHHGWR6WHS$QDO\]H
$8726(783
$8'<66(<$8726(783
(17(5 (QWHU 5(7851 &DQFHO
5HWU\
1H[W&DOFXODWLRQ
0XOW(4;7
NOTE
If “Caution” is displayed:
Go to “Error messages” (vpage 10), check
any related items, and perform the necessary
procedures.
If the problem is resolved, return and restart
“Audyssey Auto Setup”.
When performing Audyssey Auto
Setup over again
Press ui to select “Retry”, and then press ENTER .
When measuring has stopped
Press RETURN, to the “Cancel Auto Setup?”
prompt is displayed.
Press
o to select “Yes”, then press ENTER.
Setting up the speakers again
Repeat the operation from step 4 of
STEP1 Preparation
.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
STEP 2
Speaker Detection
STEP 3
Measurement
• In STEP 2, you will perform measurements at the
main listening position.
• This step automatically checks the speaker
configuration and speaker size, and calculates the
channel level, distance, and crossover frequency.
It also corrects distortion in the listening area.
6
6HOHFW ³0HDVXUH´ DQG WKHQ SUHVV
ENTER
When measuring begins, a test tone is
output from each speaker.
• Measurement requires several minutes.
7
7KHGHWHFWHGVSHDNHUVDUHGLVSOD\HG
>@
67(36SNU'HWHFW&KHFN
*RWR6WHS0HDVXUHPHQWDIWHUVSHDNHUFKHFN
5HWU\
1H[W0HDVXUHPHQW
)URQW
&HQWHU
6XEZRRIHU
6XUURXQG
<HV
<HV
<HV
<HV
$8726(783
$8'<66(<$8726(783
(17(5 (QWHU 5(7851 &DQFHO
0XOW(4;7
NOTE
If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.
8
8VH ui WR VHOHFW ³1H[W 1
0HDVXUHPHQW´DQGWKHQSUHVV
ENTER
4
&RQQHFWWKHVHWXSPLFURSKRQHWRWKH
6(7830,&MDFNRIWKLVXQLW
>@
67(33UHSDUDWLRQ
&RQQHFWWKHVSHDNHUV
DQGSODFHWKHPDFFRUG
LQJWRWKHUHFRPPHQGD
WLRQVLQWKHPDQXDO
6HWWKHIROORZLQJ
LWHPVLIQHFHVVDU\
6WDUW$XWR6HWXS
$PS$VVLJQ
&KDQQHO6HOHFW
$XWR6HWXS6WDUW
$8726(783
$8'<66(<$8726(783
0XOW(4;7
(17(5 (QWHU 5(7851 &DQFHO
When the setup microphone is
connected, the following screen is
displayed.
Here, we explain setup using the example of
5.1-channel speaker playback.
For settings other than 5.1-channel surround,
select “Amp Assign” and perform step 3 and 4 of
“Set up “Amp Assign”” (vpage53).
If unused channels are set with “Channel Select”,
measuring time can be shortened. For setting,
perform steps 5 to 10 of “Set up “Channel
Select”” (vpage53).
5
8VHuiWRVHOHFW³$XWR6HWXS6WDUW´
DQGWKHQSUHVV
ENTER