Operation Manual
ENGLISH
Symptom
Calise Countenneasure Page
No sound
is
• Subwoofer's power
not turned
•
Turn
on
the subwoofer's power.
-
produced from
on.
subwoofer.
·The
"Subwoofer"
setting
at
• Set to "Yes':
29
"Speaker Configuration"
is
set to
"No':
•
The
subwoofer
is
not properly
• Check the connections.
10
connected.
•
The
subwoofer's volume
is
• Adjust the subwoofer's
volume
63
turned
off.
to
an
appropriate level.
No test tones
are
• Surround
mode not
set to • Set to the "STANDARD" (Dolby/ 45
produced when "STANDARD"
(Dolby/DTS
DTS
Surround) mode.
main remote Surround),
control unit's
TEST
button is
pressed.
DTS
sound
is
not
• Blu-ray Disc player /
DVD
player's
• Set the
Blu-ray
Disc player /
DVD
-
output.
audio output setting
is
not set to
player.
For
details, refer to the
bitstream.
Blu-ray
Disc player /
DVD
player's
operating instructions.
• Blu-ray Disc player /
DVD
player
is
•
Use
a DTS-compatible
player.
-
not compatible with
DTS
sound
playback.
·TheAVR-1909's "Decode Mode"
• Set
to
the "Auto" or "DTS"
41
setting
is
set to "PCM
':
mode.
HDMI audio
·The
"Manual Setup" -
"HDMI
• Set to "AMP':
32
signals are not Setup" -
"HDMI
Audio
Out"
output from setting
is
set to "TV':
speakers
No
sound is
·The
"Manual Setup" -
"HDMI
• Set to "TV':
32
output from Setup" -
"HDMI
Audio
Out"
the monitor
setting
is
set to "AMP':
connected
with HDMI
connections.
Dolby TrueHD,
• HDMI
is
not connected.
• Connect the HDMI.
12,13
DTS-HD,
Dolby
• Blu-ray Disc player's audio output
• Set the
Blu-ray
Disc
player.
For
-
Digital Plus audio
setting
is
not set to bitstream.
details, refer to the
Blu-ray
Disc
is
not output.
player's operating instructions.
• Blu-ray
Disc player
is
not
• Use a DTS-compatible player. -
compatible
with
DTS
sound
playback.
[Remote Control Unit]
Syn1ptom
Cause
Countenneasure
Page
Set does not work
• Batteries
are
worn.
• Replace with
new
batteries. 3
properly when
•
You
are operating outside of the
• Operate
within the specified 3
remote control specified range. range.
unit operated.
• Obstacle between main unit
and
• Remove the obstacle.
3
remote control unit.
•
The
batteries
are
not inserted
in
• Insert
the batteries
in
the 3
the proper direction,
as
indicated proper direction,
following the
by
the polarity marks
in
the polarity marks
in
the battery
battery compartment.
compartment.
• The set's remote control sensor • Move the set to a place
in
which 3
is
exposed to strong light (direct the remote control sensor will
sunlight. invertertype fluorescent not
be
exposed to strong light.
bulb light, etc.).
• The remote
ID
of the main unit
• Set "Remote
ID"
for the main
36
and
remote control unit do not unit to "1':
match.
Symptom Cause Countenneasure
Page
No
sound
is
•
You
are
playing
a
monaural
•
The
mode
is
set to something
45
produced from source
(TV,
AM
radio broadcast, other than "STANDARD" (Dolby/
center speaker. etc.)
in
the "STANDARD" (Dolby/
DTS
Surround).
DTS
Surround) mode.
No
sound
• The surround
mode
is
set to
• Set
to a
surround playback
45,46
is
produced "STEREO", "DIRECT" or "PURE mode.
from surround DIRECT".
speakers.
No
sound
is
• The
surround back speaker's
• Check the setting and change it
35
produced from power amplifier
is
assigned to a
as
necessary.
surround
back
different channel.
speaker.
• Surround back speaker setting
is
• Set
to something other than
30
set to "None". "None"
·The
" Parameter"
-
"Surround
•
Please
set
" Parameter"
-
48,49
Parameter" - "SB
CH
Out"
"Surround
Parameter" -
"SB
settings
are
"OFF".
CH
Out"
to settings other than
"OFF"
• Surround mode not set to a mode
• Select
a
surround playback
44 - 46
for 6.1- or 7.1-channel playback.
mode.
:JJ
'"
3
o
iD
[Audio)
n
o
;;
~
83