AV SURROUND RECEIVER AVR-1906 OPERATING INSTRUCTIONS MODE D’EMPLOI
FRANCAIS SAFETY INSTRUCTIONS 2 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ENGLISH FRANCAIS 2 System setup menu / Menu de configuration système page 8 ~ 11 page page page page page 45, 46 46 46, 47 47 48 page page page page page page 40 40 40 41 42 42 page 43 page 43 page page page page 44 44 44 45
ENGLISH Getting Started Getting Started Thank you for choosing the DENON AVR-1906 A/V Surround Receiver. This remarkable component has been engineered to provide superb surround sound listening with home theater sources, such as DVD, as well as providing outstanding high fidelity reproduction of your favorite music sources. As this product is provided we recommend with an immense array of features, before you begin hookup and operation that you review the contents of this manual before proceeding.
ENGLISH Getting Started Getting Started Accessories Cautions on installation Noise or disturbance of the picture may be generated if this unit or any other electronic equipment using microprocessors is used near a tuner or TV. If this happens, take the following steps: • Install this unit as far away as possible from the tuner or TV. • Run the antenna wires from the tuner or TV away from this unit’s power supply cord and input/output connection cables.
ENGLISH Getting Started Getting Started Inserting the batteries Part names and functions q Remove the remote control unit’s rear cover. w Set two R6P/AA batteries in the battery compartment in the indicated direction. e Put the rear cover back on. Notes on batteries: • Replace the batteries with new ones if the set does not operate even when the remote control unit is operated nearby the unit. (The included batteries are only for verifying operation.
ENGLISH Getting Started Remote control unit Easy Setup and Operation For details on the functions of these parts, refer to the pages given in parentheses ( ).
ENGLISH Easy Setup and Operation Easy Setup and Operation Speaker system layout Speaker connections • Connect the speaker terminals with the speakers making sure that like polarities are matched (< with <, > with >). Mismatching of polarities will result in weak central sound, unclear orientation of the various instruments, and the stereo image being impaired.
ENGLISH Easy Setup and Operation Easy Setup and Operation 2 Connections 2 Bi-Amp connections When making connections, also refer to the operating instructions of the other components. Certain loudspeakers are equipped with two sets of input terminals, for bi-amplification. The AVR1906 Power Amp Assign. mode allows you to power bi-amp-capable speakers with two amplifier channels ( page 44). Be sure to consult the owner’s manual of your bi-amp-capable speakers for further information before proceeding.
ENGLISH Easy Setup and Operation Easy Setup and Operation • For best picture quality (especially with progressive DVD and other high definition sources), choose the component video connection to your monitor TV. S-Video and composite video outputs are also provided if your TV does not have component video inputs. Connecting a DVD player and monitor TV • To connect the video output from the DVD player to the AVR-1906, you only need to choose one connection type.
ENGLISH Easy Setup and Operation Easy Setup and Operation ON/SOURCE POWER SPEAKER A MODE 1 ENTER SETUP CURSOR ON/STANDBY SETUP MIC Auto Setup 2 Measurement and setting details q: This sets the speaker connection, polarity, and bass reproduction ability. w: This sets the delay time from each speaker corresponding to the listening position. e: This sets the volume that is output from each speaker. For accurate measurements • Keep quiet during the auto setup procedure.
ENGLISH Easy Setup and Operation Starting Auto Setup 1 Press the SETUP button. • The “System Setup” menu appears. Easy Setup and Operation 4 Press the CURSOR D or H button to select “Start”, then press the CURSOR F button. • Start the measurements. • Measurement is cancelled if the MASTER VOLUME control knob is operated while the Auto Setup is performed.
ENGLISH Easy Setup and Operation Easy Setup and Operation Check of the measurement results About error messages • These error screens may be displayed when performing Auto Setup measurement and the automatic measurements can not be completed because of the speaker arrangement, measurement environment, or other factors. Please check the following matters, reset the pertinent items, and measure again. • When there is too much noise in the room, the speakers may not be detected properly.
ENGLISH Easy Setup and Operation 4 Press the CURSOR D or H button to select from the following three items based on the measurement results, then press the CURSOR F button. Connecting Other Sources Cable indications The hookup diagrams on the subsequent pages assume the use of the following optional connection cables (not supplied). Store: Store the checked measurement values. All parameters are stored. Retry: Perform the measurement again. Measurement is repeated.
ENGLISH Connecting Other Sources Connecting Other Sources The video conversion function On-screen display signals With the AVR-1906, the Video signal and the S-Video signal which were inputted are mutually converted. And also the Video signal and the S-Video signal which were inputted are converted into a higher quality. The flow of the video signals.
ENGLISH Connecting Other Sources Connecting Other Sources Connecting a TV/DBS tuner Connecting the external inputs (EXT. IN) terminals • For best picture quality choose the component video connection to your TV or DBS tuner. S-Video and composite video inputs are also provided if your TV or DBS tuner does not have component video outputs. • To connect the digital audio output from the TV or DBS tuner, you can choose from either the coaxial or optical connections.
ENGLISH Connecting Other Sources Connecting Other Sources Connecting a VCR Connecting a tape deck • For best picture quality choose the component video connection to your VCR. S-Video and composite video outputs are also provided. • If you wish to perform analog dubbing from a digital source, such as a DVD recorder to an analog recorder such as a cassette deck, you will need to connect the analog inputs and outputs as shown below, in addition to the digital audio connections.
ENGLISH Connecting Other Sources Connecting Other Sources 2 AM loop antenna assembly Connecting the antenna terminals An F-type FM antenna cable plug can be connected directly to the unit. 1 Direction of broadcasting station Connect to the AM antenna terminals. Connection of AM antennas 3 1. Push the lever. AM loop antenna (Supplied) FM antenna 2 Remove the vinyl tie and take out the connection line. Bend in the reverse direction. 4 a. Antenna placed on a stable surface.
ENGLISH Connecting Other Sources Connecting Other Sources Connecting the MULTI ZONE terminals ZONE2 speaker out connections For instructions on operations using the MULTI ZONE functions ( • When the power amplifier is assigned to the ZONE2 output channel at “Power Amp Assign.” in the “System Setup” menu, the surround back speaker terminals can be used as the ZONE2 speaker out terminals ( page 36).
ENGLISH Connecting Other Sources Connecting Other Sources Connecting the pre-out terminals Connecting the power supply cord • Use these terminals if you wish to connect external power amplifier(s) to increase the power of the front, center, surround and surround back sound channels, or for connection to powered loudspeakers. • When using only one surround back speaker, connect it to the left channel.
ENGLISH Basic Operation Playback using the external input (EXT. IN) terminals Basic Operation The signals being input to the external decoder input terminals are played without passing through the surround circuitry. Playback INPUT MODE FUNCTION ANALOG SURROUND MODE MASTER VOLUME FUNCTION MAIN EXT. IN SURROUND MODE SELECT VOLUME Playing the input source 1 MUTING Select the input source to be played.
ENGLISH Basic Operation Basic Operation 2 Using the dimmer function INPUT MODE ANALOG DIMMER STATUS Press the DIMMER button. ON SCREEN VIDEO SELECT INPUT MODE PHONES SPEAKER DIMMER SPEAKER ANALOG Input mode VIDEO SELECT Listening over headphones Connect the headphones to the PHONES jack. • The pre-out output (including the speaker output) is automatically turned off when headphones are connected. NOTE: • To prevent hearing loss, do not raise the volume level excessively when using headphones.
ENGLISH Basic Operation 2 Selecting the analog mode Basic Operation 2 Input mode display 2 Input signal display • In the AUTO mode • DOLBY DIGITAL Press the ANALOG button to switch to the analog input. ANALOG (exclusive analog audio signal playback mode): The signals input to the analog input terminals are decoded and played. NOTE: • Input mode when playing DTS sources: Noise will be output if DTS-compatible CDs or LDs are played in the “ANALOG” or “PCM” mode.
ENGLISH Basic Operation Basic Operation STANDARD DIRECT/STEREO STANDARD DIRECT STEREO SURROUND PARAMETER CURSOR ENTER 4 Turn the SELECT knob, and press the CURSOR F or G button to select the optimum mode for the source. When the “SB CH OUT” parameter is set to “ON”. (Set “S. BACK” at system setup to “SMALL” or “LARGE”.
ENGLISH Basic Operation 6 Turn the SELECT knob, and press the CURSOR F or G button to set the various surround parameters. When the surround parameters are set using the buttons on the main unit, stop operating the buttons after completing the settings. The settings are automatically finalized and the normal display reappears after several seconds. 7 Press the ENTER button to finish the surround parameter mode.
ENGLISH Basic Operation INPUT MODE Basic Operation STANDARD/ NIGHT STATUS 2 Surround parameters e STANDARD FUNCTION SURROUND PARAMETER CURSOR ENTER SURROUND MODE FUNCTION SURROUND PARAMETER SELECT SURROUND BACK ON SCREEN Dolby Digital mode and DTS surround (only with digital input) 1 INPUT MODE Select an input source set to digital (COAXIAL/ OPTICAL) ( page 40). 5 Press the SURROUND PARAMETER button. • The surround parameter menu is displayed.
ENGLISH Basic Operation SB CH OUT (Surround Back): (1) Multi-channel source • OFF: Playback is conducted without using the surround back speaker. • NON MTRX: The same signals as those of the surround channels are output from the surround back channels. • MTRX ON: The surround back channel is reproduced using digital matrix processing. • ES MTRX: When playing DTS signals, the surround back signals undergo digital matrix processing for playback.
ENGLISH Basic Operation Basic Operation STANDARD FUNCTION INPUT MODE FUNCTION ENTER CURSOR STANDARD INPUT MODE Adjusting the audio delay • When watching a DVD or other video source, the picture on the monitor may seem delayed with respect to the sound. In this case, adjust the audio delay to delay the sound and synchronize it with the picture. • The audio delay setting is stored separately for each input source.
ENGLISH Basic Operation Basic Operation DENON original surround modes This unit is equipped with a high performance DSP (Digital Signal Processor) which uses digital signal processing to synthetically recreate the sound field. One of 7 preset surround modes can be selected according to the program source and the parameters can be adjusted according to the conditions in the listening room to achieve a more realistic, powerful sound.
ENGLISH Basic Operation Basic Operation SURROUND MODE TONE CONTROL When turned counterclockwise: DIRECT SURROUND MODE MONO MOVIE SURROUND PARAMETER CURSOR CH SELECT / ENTER SURROUND PARAMETER SELECT TONE DEFEAT DSP surround simulation 2 To operate the surround mode and the surround parameters from the remote control unit 1 Select the surround mode for the input channel. 3 Press the SURROUND PARAMETER button, and press the CURSOR D or H button to select the various parameters.
ENGLISH Basic Operation Basic Operation Tone control setting Channel Level The tone control function will not work in the DIRECT mode. You can adjust the channel level either according to the playback sources or to suit your taste, as described below. 1 1 2 Adjusting the sound quality (tone) Press the TONE CONTROL button. The tone switches as follows each time the TONE CONTROL button is pressed. BASS 2 The channel switches as shown below each time the button is pressed.
ENGLISH Basic Operation FUNCTION Basic Operation BAND Auto tuning PRESET TUNING TUNER PRESET MODE MEMORY 1 Set the input source to “TUNER”. SHIFT BAND (Main unit) POWER ON/STANDBY SHIFT ON SCREEN TUNING Listening to the radio Auto preset memory • This unit is equipped with a function for automatically searching for FM broadcast stations and storing them in the preset memory. • The “Auto tuner preset” operation can also be performed at “System setup” ( page 42).
ENGLISH Basic Operation Manual tuning 1 2 3 Set the input source to “TUNER”. Watching the display, press the BAND button to select the desired band (AM or FM). Press the MODE button to set the manual tuning mode. Check that the display’s “AUTO” indicator turns off. 4 Press the TUNING (+) or (–) button to tune in the desired station. The frequency changes continuously when the button is held in.
ENGLISH Advanced Operation Advanced Operation OFF ON/SOURCE 1. CD player (CD), CD recorder and MD recorder (CDR/MD) system buttons 3. Tuner system buttons NUMBER MODE 1 MODE 2 Remote control unit 6, 7 2 1 8, 9 3 DISC SKIP + Operating DENON audio components 1 Set the MODE 1 switch to “AUDIO”. 2 Set the MODE 2 switch to the position for the component to be operated (CD, CDR/MD or TAPE).
ENGLISH Advanced Operation Advanced Operation Preset memory • DENON and other makes of components can be operated by setting the preset memory. • This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the manufacturer of the component as shown in the list of preset codes ( End of this manual). • Operation is not possible for some models. 1 Set the MODE 1 switch to “AUDIO” or “VIDEO”.
ENGLISH Advanced Operation 2. Video disc player (VDP) system buttons ON/SOURCE : Power on/standby 6, 7 : Manual search (forward and reverse) 2 : Stop 1 : Play 8, 9 : Auto search (cue) 3 : Pause 0 ~ 9, +10 : Number Advanced Operation 3. Video deck (VCR) system buttons ON/SOURCE : Power on/standby 6, 7 : Manual search (forward and reverse) 2 : Stop 1 : Play 3 : Pause Channel +, – : Channel up/down 33 ENGLISH 4.
ENGLISH Advanced Operation Advanced Operation 5. Monitor TV (TV) system buttons MAIN ON ZONE2 OFF NUMBER MODE 2 MODE 1 Punch through “Punch Through” is a function allowing you to operate the PLAY, STOP, MANUAL SEARCH and AUTO SEARCH buttons on CD, TAPE, CDR/MD, DVD/VDP or VCR components when in the DBS/CABLE or TV mode. By default, nothing is set.
ENGLISH Advanced Operation Advanced Operation Multi zone music entertainment system • When the outputs of the ZONE2 OUT terminals are wired and connected to integrated amplifiers installed in other rooms, different sources can be played in rooms other than the MAIN ZONE in which this unit and the playback devices are installed. (Refer to ZONE2 on the diagram below.) • ZONE2 speaker out and pre-out can be used when “ZONE2” is selected at “Power Amp Assign.” in the “System Setup” menu.
ENGLISH Advanced Operation Advanced Operation 2 When using the SURR.BACK/ZONE2 amplifier as the ZONE2 • The SPEAKER OUT, LINE OUT and PRE OUT terminals can be used simultaneously in ZONE2. • To use the ZONE2, turn on the ZONE2 button. • The output of the ZONE2 SPEAKER OUT terminals can be adjusted with the remote control unit’s ZONE2 VOLUME button. [System configuration and connections example] Using this unit’s internal amplifier as the ZONE2. MAIN ZONE 5.
ENGLISH Advanced Operation Advanced Operation ZONE2 OFF ZONE2 ON FUNCTION ZONE2/REC SELECT FUNCTION CHANNEL MODE 2 MODE 1 POWER ZONE2 SPEAKER VOLUME Outputting a program source to amplifier, etc., in a different room (ZONE2 mode) 1 Press the ZONE2/REC SELECT button to display the “ZONE2 SOURCE” on the display. Remote control unit operations during multi-source playback (selecting the source) 1 Set the MODE 1 switch to the “AUDIO”. 2 Set the MODE 2 switch to the “ZONE2”.
ENGLISH Advanced Operation Advanced Operation Other functions Playing one source while recording another (REC OUT mode) 1 Press the ZONE2/REC SELECT button to display the “RECOUT SOURCE” on the display. The display switches as follows each time the button is pressed. ZONE2 2 3 REC Turn the FUNCTION knob to select the source you want to output appears on the display. Set the recording mode. For operating instructions, refer to the manual of the component on which you want to record.
ENGLISH Advanced Setup – Part 1 On-screen display and front display Advanced Setup – Part 1 The AVR-1906 is equipped with an intuitive and easy-to-understand on-screen display, and is equipped with an alphanumeric front panel display that can also be used to check and adjust settings. We recommend that you use the on-screen display when you make system adjustments. Some representative front display and on-screen display examples are shown below.
ENGLISH Advanced Setup – Part 1 Advanced Setup – Part 1 Input Setup Setting the Input Function Level Setting the Digital In Assign. This setting assigns the digital input terminals of the AVR-1906 for the different input sources. 1 Press the CURSOR D or H button to select “Input Setup” at the “System Setup” menu, then press the ENTER button. • The “Input Setup” screen appears.
ENGLISH Advanced Setup – Part 1 Setting the Function Rename The names of the input sources displayed on the front display and the on-screen display can be changed. The names or brands of the devices connected to the input sources can be input. 1 Press the CURSOR D or H button to select “Function Rename” at the “Input Setup” menu, then press the ENTER button. Advanced Setup – Part 1 4 Repeat step 3 to complete input of the input source name.
ENGLISH Advanced Setup – Part 1 Advanced Setup – Part 1 Setting the Video Input Mode Select the input signal to be output to the composite S-Video and component monitor output terminals using the video conversion function. 1 Press the CURSOR D or H button to select “Video Input Mode” at the “Input Setup” menu, then press the ENTER button. • The “Video Input Mode” screen appears.
ENGLISH Advanced Setup – Part 1 Advanced Setup – Part 1 Advanced playback Setting the Audio Delay • When watching a DVD or other video source, the picture on the monitor may seem delayed with respect to the sound. In this case, adjust the audio delay to delay the sound and synchronize it with the picture. • The audio delay setting is stored separately for each input source. 1 Press the CURSOR D or H button to select “Advanced Playback” at the “System Setup” menu, then press the ENTER button.
ENGLISH Advanced Setup – Part 1 Advanced Setup – Part 1 Option Setup Setting the Muting Level This sets the amount of attenuation applied for audio output muting. 1 Press the CURSOR D or H button to select “Option Setup” at the “System Setup” menu, then press the ENTER button. Setting the Power Amp Assign. Setting the On-Screen Display (OSD) • Use this to turn the on-screen display (messages other than the menu screens) “ON” or “OFF”. • Sets the on-screen display mode.
ENGLISH Advanced Setup – Part 1 Setting the Setup Lock The system setup settings can be locked so that they cannot be changed easily. 1 Press the CURSOR D or H button to select “Setup Lock” at the “Option Setup” menu, then press the ENTER button. Advanced Setup – Part 2 This Speaker Setup section describes the procedures to make speaker settings manually (without using the Auto Setup function), as well as to make manual changes to settings that have already been made by the Auto Setup function.
ENGLISH Advanced Setup – Part 2 Advanced Setup – Part 2 2 Parameters Large: Select this when using speakers that have sufficient ability to reproduce bass sound below the frequency set for the crossover frequency mode. 1 Press the CURSOR D or H button to select “Delay Time” at the “Speaker Setup” menu, then press the ENTER button. • The “Delay Time” screen appears.
ENGLISH Advanced Setup – Part 2 4 -1 Advanced Setup – Part 2 When “Auto” mode is selected: Press the CURSOR F or G button to adjust all the speakers to the same volume. • The test tones are emitted from each speaker in the following order: at 4-second intervals during the first and second cycle, and at the 2-second intervals during the third and subsequent cycles.
ENGLISH Advanced Setup – Part 2 Setting the SW Mode Setup Set the subwoofer mode according to the speaker system being used. 1 Press the CURSOR D or H button to select “SW Mode Setup” at the “Speaker Setup” menu, then press the ENTER button. • The “Subwoofer Mode Setup” screen appears. 2 3 4 Press the CURSOR F or G button to select a setting. Press the ENTER button to enter the setting. • The “Speaker Setup” menu appears.
ENGLISH Advanced Setup – Part 2 Advanced Setup – Part 2 System setup items and default values (set upon shipment from the factory) 1. Auto Setup Auto Setup 1 Auto Setup Power Amp Assign. Set this to switch the surround back channel’s power amplifier for ZONE2 or BiAmp use . Default setting Page SURROUND BACK 8~11 2. Speaker Setup Speaker Setup 1 Speaker Config.
ENGLISH Advanced Setup – Part 2 Advanced Setup – Part 2 4. Advanced Playback Advanced Playback Default setting Page 0 ms 43 1 Audio Delay Sets the audio delay to delay the sound and synchronize it with the picture. Auto 2 Surround Mode Sets the Auto surround mode function. Auto Surround Mode = ON 43 Option Setup 5. Option Setup Default setting Page 1 Muting Level This sets the amount of attenuation for audio output muting.
ENGLISH Troubleshooting Symptom Troubleshooting If a problem should arise, first check the following. 1. Are the connections correct? 2. Have you operated the receiver according to the operating instructions? 3. Are the speakers and other components operating properly? If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction. Disconnect the power immediately and contact your store of purchase.
ENGLISH Additional Information Surround back speakers Additional Information • Other types of audio: These signals are designed to recreate a 360° sound field using three to five speakers. Optimum surround sound for different sources There are currently various types of multi-channel signals (signals or formats with more than two channels).
ENGLISH Additional Information With this set, speaker(s) for 1 or 2 channels are required to achieve a 6.1-channel system (DTS-ES, etc.). Adding these speakers, however, increases the surround effect not only with sources recorded in 6.1 channels but also with conventional 2- to 5.1-channel sources. Furthermore, all the DENON original surround modes ( page 26) are compatible with 7.1-channel playback, so you can enjoy 7.1-channel sound with any signal source.
ENGLISH Additional Information Additional Information [2] When not using surround back speakers Front speakers Center speaker Monitor Subwoofer 60° 120° Surround speakers [ As seen from above ] Surround speaker Surround The AVR-1906 is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same sense of presence as in a movie theater.
ENGLISH Additional Information • Whereas with conventional Dolby Pro Logic the surround channel playback frequency band was limited, Dolby Pro Logic II offers a wider band range (20 Hz to 20 kHz or greater). In addition, the surround channels were monaural (the surround left and right channels were the same) with previous Dolby Pro Logic, but with Dolby Pro Logic II they are played as stereo signals.
ENGLISH Additional Information [3] DTS-ES Extended Surround™ DTS-ES Extended Surround is a new multi-channel digital signal format developed by Digital Theater Systems Inc. While offering high compatibility with the conventional DTS Digital Surround format, DTS-ES Extended Surround greatly improves the 360degree surround impression and space expression thanks to further expanded surround signals. This format has been used professionally in movie theaters since 1999. In addition to the 5.
ENGLISH Additional Information Additional Information Surround modes and parameters Signals and adjustability in the different modes When playing Dolby Digital and DTS signals Channel output Mode DIRECT STEREO EXTERNAL INPUT DOLBY PRO LOGIC II DOLBY PRO LOGIC IIx DTS NEO:6 DOLBY DIGITAL DTS SURROUND 5CH/7CH STEREO ROCK ARENA JAZZ CLUB VIDEO GAME MONO MOVIE MATRIX VIRTUAL FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R SUBWOOFER C C C C C C C C C C C C C C C E E B B B B B B B B B B B B E E E B B
ENGLISH Specifications 2 Tuner section Specifications Receiving Range: Usable Sensitivity: 50 dB Quieting Sensitivity: 2 Audio section • Power amplifier Rated output: Output terminals: • Analog Input sensitivity / input impedance: Frequency response: S/N: Distortion: Rated output: Front: 85 W +85 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08% 120 W + 120 W (6 Ω/ohms, 1 kHz with 0.7% T.H.D.) Center: 85 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08% 120 W (6 Ω/ohms, 1 kHz with 0.7% T.H.D.
ENGLISH FRANCAIS 2 List of preset codes / Liste de codes préréglés DVD Audio Dynamic 005, 085 014, *[111] Audiovox 088 Aiwa 009 Beaumark 087 Jensen Hitachi 010 Broksonic 086, 093 JVC JVC 006, 011 Calix 088 Konka 012, 013 Candle 006, 087, 088, 089, 090 Magnavox 005 Canon 049, 057 Mitsubishi 004 Capehart 025, 055, 056, 071 Kodak 088 Panasonic 014 Carver 015 Lloyd 009, 094 Philips 005, 015, 016, 017 CCE 095 LXI 088 Pioneer 003, 008 Citizen 006, 007, 087, 088,
FRANCAIS Optonica 021 Sylvania 009, 015, 016, 017, 041, 049, 094 Bauer Panasonic 024, 049, 064, 066, 067, 068, 069, 107 Symphonic 009, 094 Belcor 047 Perdio 009 Tandy 009 Bell & Howell 045, 118 Pentax 009, 013, 023, 058, 090 Tashiko 009, 088 Bradford 061 Philco 015, 016, 049 Tatung 004, 026, 030 Brockwood 003, 047 Philips 015, 021, 042, 049, 105 Teac 004, 009, 026, 094 Candle Pilot 088 Technics 024, 049 Pioneer 005, 013, 029, 036, 037, 038, 045, 085 Teknika 009, 010,
ENGLISH FRANCAIS Futuretech GE 004 Minutz 020, 036, 037, 040, 044, 058, 066, 088, Mitsubishi 119, 120, 125, 147 Goldstar 066 SBR 015 001, 016, 039, 048, 056, 057, 058, 065, Schneider 015 081, 082, 083, 105 Scott 062 Sears 000, 015, 029, 031, 039, 048, 051, 056, Montgomery Ward 011, 020, 144, 145, 146 057, 067, 068, 069, 116 Motorola 121, 147 Grundy 062 MTC 031, 034, 039, 048, 095 Hitachi 029, 031, 051, 052, 070, 111, 112, 113, NAD 008, 075, 076, 128 124, *[134] National 002
FRANCAIS CABLE ABC 006, *[007], 008, 009 DBS (SATELLITE) Emerson 004, 005, 006, 007 Alphastar 054 Fisher 003, 008, 009, 010 018, 019 Archer 010, 011 Chaparral 035, 036 JVC Century 011 Dishnet 053 Kenwood 011, 012, 013, 014, 017 Magnavox 006, 015, 035 Citizen 011 Drake 037, 038 Colour Voice 012, 013 Echostar Dish 062, 066 Marantz 016, 028, 035 016, 024 Comtronic 014 GE 048, 055, 056 MCS Eastern 015 General Instruments 039, 040, 041 Onkyo 025, 027 017, 020, 021, 022,
ENGLISH FRANCAIS Magnavox 002 Marantz 002 Onkyo 016, 018 Optimus 007, 008 Panasonic 012 Philips 002 Pioneer 007, 008, 009 Sony 013, 014, 015 Technics 012 Victor 004 Wards 007 Yamaha 010, 011 *[ ] : Preset codes set upon shipment from the factory. *[ ] : Les codes préréglés diffèrent en fonctiom des livraison de l’usine. DVD preset codes Codes préréglés DVD B Model No.
TOKYO, JAPAN www.denon.com Denon Brand Company, D&M Holdings Inc.
DENON SERVICE NETWORK I DIU~fM~ Please consult the outlet where the equipment was purchased. Bitte wenden Sie sich an den Handler, bei dem Sie das Produkt gekaufthaben. SVP veuillez consulter votre revendeur. Neemt u alstublieft contact op met het verkooppuntwaar u de apparatuur heeft gekocht. Por favor consulte en el establecimiento donde compr6 el equipo. Vanligen ta kontakt med butiken dar du kopt utrustningen. Rivolgetevi al rivenditore che vi ha venduto l'apparecchio.
DE NON® LIMITED WARRANTY (USA / CANADA) USA (ENGLISH) CANADA (ENGLISH) CANADA (FRENCH) PAGE 2 3 4 USA DENON ELECTRONICS (USA), LLC (a D&M Holdings Company/Warranty Repair Information: Call {630) 7 41-0300) 19C Chapin Road, Suite 205 Pine Brook, NJ 07058-9385 (973) 396-0810 (973) 396-7448 Fax DENON REGIONAL SUPER SERVICE CENTERS (Repair only-No parts orders please) PYRAMID AUDIO UNITED RADIO SERVICE AUDIO SERVICES 305 E.
~-•tlll•~·•tlll•·. .·•tlll•. . .·•tllt•~ ..... .~ ,,ut•...-•tlll• ....·•tlll•. . .·•tl~l•. . .·•tlll•·_,..·•tlll•....·•dlt••....•IIII•-4J-·•tlll•. . .-•tlll•·....-•tJII•·....·•tlll• ....·•tlll". . .''llt• . . .·•tll1•·. . .·•1llh·. . .·•tlll•·. . .·•tl\l• .....·•tllt• ..... ,,llt•-.....•tlll•·....-•tll1•·....·•1lii•·....·•IJII•·. . .·•Illl•....·•tlll•·. . .·•llll•. . .·•tlll' ~ This warranty will be honored only m the U.S.
