Operating instructions

With the name of the volume to
be adjusted selected, tum the ,._.,
SELECT knob to adiust the level
• To increase tile bass or treble:
Turn the control clockwise
{Tile bass or treble sound can {Mainunit)
be increased to up to +I 2 dB in steps of 2 dB)
• To decrease the bass or treble: Turn the
control counterclockwise (The bass or
treble sound can be decreased to up to -12
dBin steps of 2 dB)
If you do not want the bass and treble to be
adjusted, turn on the tone defeat mode
_E_ m The signals do not pass through the
bass and treble adjustment circuits.
providing higher quality sound
(Main unit}
[2] Listening over headphones
Plug the headphones' plug into
the iack @
Connect the headphones to /_ _
the PHONES jack _ _1'
The pre-out output (including 1
the speaker output) is
automatically turned off
when headphones are
connected
NOTE:
_o.Es To prevent hearing loss, do not raise the volume level
excessively when using headphones
oo_ooo
o o
ooo _ ann
[5] Checking the currently playing program source, etc,
Front panel display
• Descriptions of the unit's operations m
are also displayed on the front panel
display In addition, the display can
be switched to check the unit's
operating status while playing a {Remote
SOUrce by pressing the STATUS c°n_luIunit_
button
2
Using the dimmer function
• Use this to change the brightness of =_=
the display %
The display brightness changes in
four steps (bright, medium, dim and
off) by pressing the main unit's {Remote
DIMMER button repeatedly controlunit_
8REGHT _MEDIUM _ DIM
OFF
2
[3] Turning the sound off temporarily ( muting}
Use this to turn off the audio output _,
temporarily
Press the MUTING button
Cancelling MUTING mode {Remote
Press the MUTING button again controlunt)
Muting will also be cancelled
when MASTER VOL is adjusted
up or down
[4] Combining the currently playing sound with the desired image
Simulcast playback
Use this switch to monitor a video
source other than the audio source
Press the VIDEO SELECT button
repeatedly until the desired source {Remote
appears on the display controlur/t)
Cancelling simulcast playback
• Select "SOURCE" using the VIDEO SELECT
button
• Switch tile program source to the component
connected to the video input jacks
Set the external input (EXT IN) mode
Press the EXT IN button
_T.IN
tO_nputSWitchthe external % %
Once this is selected, (Mainunit} {Remote
the input signals °°nt/°l unit}
connected to the FL {front left), FR (front right),
C (center), SL {surround left) and SR (surround
right) channels of the EXT IN jacks are output
directly to the front (left and right), center,
surround {left and right) speaker systems
without passing through the surround circuitry
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SUBWOOFER jack
2
Cancelling the external input mode
To cancel the external input (EXT IN) setting,
press the INPUT MODE (AUTO. PCM. DTS) or
ANALOG button to switch to the desired input
mode (See page 16)
I_'_T UOaE
%%%%
{Man unt) {Remote control urn]t)
• When the input mode is set to the external input
(EXT IN), the play mode (DIRECT,STEREO,
DOLBY/DTS SURROUND, 5CH STEREO or DSP
SIMULATION) cannot be selected
2 1
o._
Oo ...... _©_
NOTES:
• In play modes other than the external input mode,
the signals connected to EXT IN jacks cannot
be played In addition, signals cannot be output
from channels not connected to the input jacks
• The external input mode can be set for any input
source To watch video while listening to sound.
select the input source to which tile video signal
is connected, then set this mode
17