Installation and Operating Instructions for Ceramic Glass Radiant Electric Cooktop Models CTR1 CTR2 CTR3 Model # _______________ Serial # ________________ You can find them on a label under the cooktop. To prevent accidents and machine damage, read the Installation & Operating Manual before installation and use. www.DENALIplus.com Write the model and serial numbers here: 0 Page F-10002-R0 SAVE THIS MANUAL FOR FUTURE REFERENCE.
Table of Contents Safety Instructions…………................................................................................................................... Installation Instructions for Ceramic Glass Cooktops Step #1: Unpacking the Cooktop…………….............................................................................. Step #2: Check the Electrical Supply Requirements …........................................................... Step #3: Countertop Preparation & Cutout Dimension…..........................
IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING. For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING. SAFETY PRECAUTIONS SAVE THESE INSTRUCTIONS 3 cause hot fat to bubble up and over the sides of the pan. Use little fat for effective shallow or deep-fat frying. Filling the pan too full of fat can cause spillovers when food is added. If a combination of oils or fats will be used in frying, stir together before heating, or as fats melt slowly. Always heat fat slowly, and watch as it heats.
IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING. RADIANT SURFACE ELEMENTS Clean the cooktop with caution. If a wet sponge or cloth is used to wipe spills on a hot surface element, be careful to avoid steam burns. Some cleansers can produce noxious fumes if applied to a hot surface. NOTE: We recommend that you avoid wiping any surface element areas until they have cooled and the indicator light has gone off. Sugar spills are the exception to this.
INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT - Save these instructions for local inspector’s use. IMPORTANT - Observe all governing codes and ordinances. Note to Installer – Be sure to leave these instructions with the Consumer. Note to Consumer – Keep these instructions for future reference. Product failure due to improper installation is not covered under the Warranty.
Step #1 - Unpacking the Cooktop Carefully unpack the cooktop from its shipping container. If possible, retain the original shipping carton and protective packaging in the event the unit ever has to be returned for service. Verify and identify the package contents. The following items should be included in the carton. If any components are missing or damaged, call DENALI+ customer service immediately. Radiant Electric Cooktop Mounting brackets (2 pcs. for Single and Double Burners, 4 pcs.
Step #3 - Countertop Preparation Please read this section prior to making cutout for the cooktop. It is important to plan ahead for installation of the cooktop, keeping the following dimensions in mind (please refer to Fig. 2). A. 36 inches is minimum height of countertop above floor B. 13 inches maximum depth of overhead C.
Before making the countertop cutout, check for clearance. Check to see if the cooktop will clear the front and side walls of the base cabinet. It is also important to provide enough ventilation. Adequate ventilation of the space below the countertop must be provided to ensure proper operation of the cooktop. Heat transferred from the cooktop bottom pan during operation will overheat an improperly ventilated area. Fig.
Fig. 4c (Model CTR3) NOTE: When making the countertop, radius the corner of the cutout (1/4” radius is typical). This will prevent cracking of the countertop. Follow manufacturer’s instructions regarding minimum corner radius and reinforcement of corners. Depth 11⅞" 19⅛" 18⅜" Step #4 - Installing the Cooktop 1. Strips of foam sealant have already been installed around the outer edge of the underside of the cooktop. This special sealant prevents liquid from infiltrating into the cabinet.
glass ceramic cooktops and four brackets for the triple glass ceramic cooktop. These brackets are designed to tighten the cooktop and then seal it onto the counter to avoid any movement of the cooktop and to provide good insulation. NOTE: BE CAREFUL NOT TO OVERTIGHTEN THE SCREWS. 10 Fig. 7 Page Fig. 6 www.DENALIplus.com Fig.
Fig. 8 NOTE: CARRIER BRACKETS AND SELF ADHESIVE SEALANT ARE FACTORY INSTALLED. Grounding: The entire appliance must be grounded at all times when the electrical power supply is on. Connect the red to red, black to black and green to ground. Do not ground the appliance with the neutral house supply wire. A separate ground must be used. 11 Attach conductor wires to residence wiring in accordance with national, state and local electric codes.
STEP #6 - Final Preparations Prior to Use Clean the cooktop before you use it for the first time. A thorough cleaning with a cooktop cleaner will provide a clean, shiny coating on the cooktop surface. The next sections of the manual cover cooktop safety, operation, maintenance and service information. Please keep these instructions with the DENALI + cooktop for future OPERATING INSTRUCTIONS READ SAFETY INSTRUCTIONS BEFORE OPERATING YOUR APPLIANCE.
temperature limiter will cycle the radiant element on and off to prevent exceeding the maximum safe surface temperature. Controls & Indicators Each of the cooking area controls has an infinite selection of heat settings. The control settings begin at low and increase heat output by cycling the heating elements between OFF and full power as you turn the knob clockwise.
ONE-YEAR LIMITED WARRANTY Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or furnished with the product, warrantor will pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a designated service company. Outside the 48 states, all parts are warranted for one year from manufacturing defects.
