ASSEMBLY INSTRUCTIONS FOR THE DF838 LAT ATTACHMENT (888) 258-0533 FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
DF830 COMPONENTS A B TOP FRAME QTY 1 BOTTOM SUPPORT QTY 1 D C LOW BAR QTY 1 LAT BAR QTY 1 E F CABLE QTY 2 REAR SUPPORT QTY 1 H I FLOATING PULLEY ASSEMBLY FLANGE QTY 2 4” FLANGE QTY 2 DF830 HARDWARE QTY 1 G FRONT SUPPORT QTY 1 DF830 INSTRUCTIONS QTY 1 *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
DF830 HARDWARE J K L M RUBBER SHOE QTY 4 2” x 3” CAP QTY 1 3-1/2” PULLEY QTY 6 PULLEY BUSHING QTY 6 N O P Q 10” CHAIN QTY 1 M12 x 76MM BOLT QTY 8 M12 x 65MM BOLT QTY 2 M10 x 76MM BOLT QTY 2 R S T M12 LOCKNUT QTY 12 M12 WASHER QTY 20 SNAP HOOK QTY 5 U V W X M10 x 43MM BOLT QTY 4 3/8” x 1” BOLT QTY 2 M10 WASHER QTY 14 M10 LOCKNUT QTY 6 *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
WEIGHT STACK COMPONENTS AA BB BOTTOM FRAME QTY 1 UPPER PULLEY ASSEMBLY QTY 1 EE RUBBER DOUGHNUTS QTY 2 CC 200 LB WEIGHT STACK QTY 1 DD WEIGHT SELECTOR ROD QTY 1 FF GG WEIGHT STACK PIN QTY 1 CHROME RODS QTY 2 *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
FRAME ASSEMBLY R F G B S TOOLS METRIC WRENCHES OR SOCKET SET REQUIRED: INSTALL THE REAR SUPPORT (F) TO THE BOTTOM SUPPORT (B), ALIGNING HOLES IN FLANGE WITH PIN AND THREADED STUD. INSTALL 12MM WASHER (S) AND 12MM NUT (R) AND TIGHTEN. INSTALL THE FRONT SUPPORT (G) TO THE BOTTOM SUPPORT (B), ALIGNING HOLES IN FLANGE WITH PIN AND THREADED STUD. INSTALL 12MM WASHER (S) AND 12MM NUT (R) AND TIGHTEN.
FRAME ASSEMBLY (NOTE: THE NUTS USED ON THIS ARE LOCKNUTS, THIS MEANS YOU MUST TIGHTEN THEM DOWN PAST THE PLASTIC INSERT.) L W X J W W L U W INSTALL THE 3 1/2” PULLEYS (L) INTO THE FRAME USING THE M10 x 43MM BOLTS (U), THE M10 FLAT WASHERS (W), AND THE M10 LOCKNUTS(X). INSTALL THE RUBBER SHOE (J) ONTO THE BOTTOM SUPPORT.
TOP FRAME ASSEMBLY (NOTE: THE NUTS USED ON THIS ARE LOCKNUTS, THIS MEANS YOU MUST TIGHTEN THEM DOWN PAST THE PLASTIC INSERT.) K A W M M Q L INSTALL THE 3-1/2” PULLEYS (L) INTO THE TOP FRAME (A) USING THE PULLEY BUSHINGS (M), THE M10 x 75MM BOLTS (Q), AND THE M10 LOCK NUTS (W). NOW INSERT THE 2” x 3” CAP (K) INTO THE END OF THE TOP FRAME (A).
FRAME ASSEMBLY S P R S INSTALL THE UPPER FRAME ASSEMBLY TO THE FRAME SUPPORTS WITH M12 x 65MM BOLTS (P), M12 WASHERS (S), AND M12 LOCKNUTS (R).
FLOATING PULLEY ASSEMBLY L X W W U H ASSEMBLE THE FLOATING PULLEY ASSEMBLY BY USING 3-1/2” PULLEYS (L), FLANGES (H), M10 x 43MM BOLTS (U), M10 WASHERS (W), AND M10 LOCKNUTS (X).
FINAL INSTALLATION R S I S O R S S I O ATTACH THE LAT ATTACHMENT TO THE POWER RACK OR SMITH MACHINE USING THE M12 x 75MM BOLTS (O), 4” FLANGE PLATES (I), M12 WASHERS (S) AND M12 LOCKNUTS (R).
WEIGHT STACK FRAME ASSEMBLY O R S S J J AA INSTALL THE RUBBER SHOES (J) 0NTO THE BOTTOM SUPPORT(AA). ATTACH THE BOTTOM SUPPORT (AA) TO THE LAT ATTACHMENT USING THE M12 x 75MM BOLTS (O) THE M12 FLAT WASHERS (S) AND THE M12 LOCK NUTS (R).
WEIGHT STACK ASSEMBLY DD FF CC GG EE INSTALL THE RUBBER DOUGHNUTS (EE) ONTO THE BOTTOM OF THE CHROME RODS (GG) , LEAVING APPROXIMATELY 2” PROTRUDING. INSERT THE CHROME RODS INTO THE TWO OUTER HOLES IN THE BOTTOM SUPPORT. ASSEMBLE THE WEIGHT STACK (CC) BY SLIDING EACH PLATE OVER THE CHROME RODS (J) AND ON TO THE BOTTOM SUPPORT. SLIDE THE SELECTOR ROD/TOP PLATE ASSEMBLY (DD) OVER THE CHROME RODS (GG) AND THROUGH THE WEIGHT STACK (CC).
UPPER PULLEY ASSEMBLY INSTALLATION O S BB V S R REMOVE THE BOLTS, NUTS, AND WASHERS THAT HOLD THE UPPER PULLEY FRAME ASSEMBLY TO THE BODY. INSTALL THE UPPER PULLEY ASSEMBLY (BB) TO THE LAT ATTACHMENT USING M12 x 75MM BOLTS (O), M12 WASHERS (S), AND M12 LOCKNUTS (R). ATTACH THE UPPER PULLEY ASSEMBLY (BB) TO THE CHROME RODS USING 3/8” x 1” BOLTS (V).
UPPER CABLE INSTALLATION UPPER PULLEY FRAME REMOVED FOR CLARITY NOTE: UPPER CABLE IS SHORTER THAN THE BOTTOM CABLE FLOATING PULLEY ASSEMBLY INSTALL UPPER CABLE OVER FRONT PULLEY, BACK TO REAR PULLEY, DOWN TO TOP PULLEY OF FLOATING PULLEY ASSEMBLY, UP TO STACK ASSEMBLY PULLEY AND DOWN TO SELECTOR ROD ASSEMBLY. ATTACH 8MM SNAP HOOK TO END OF CABLE AND THEN TO SELECTOR ROD BRACKET.
LOWER CABLE INSTALLATION INSTALL LOWER CABLE UNDER FRONT PULLEY AND BACK TO REAR PULLEY. CONTINUE UP AND OVER LOWER PULLEY OF FLOATING PULLEY ASSEMBLY. ATTACH 8MM SNAP HOOK TO END OF CABLE AND THEN TO FRAME POLE BRACKET.
SAFETY NOTICE WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS FOLLOWING THESE SIMPLE RULES: 1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU. 2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM, PROPER STRETCHING WILL PREPARE YOUR JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
