Technical information
Table Of Contents
- Contents
- About this manual
- Introduction
- General descriptions
- ThinkPad R40
- Product overview
- Symptom-to-FRU index
- FRU replacement notices
- Removing and replacing a FRU
- 1010 Battery pack
- 1020 Ultrabay Plus device
- 1030 Hard-disk drive
- 1040 DIMM
- 1050 Mini PCI adapter
- 1060 Keyboard
- 1070 Backup battery
- 1080 Optical storage in the fixed bay
- 1090 PC Card slot assembly
- 1100 Hinge cover
- 1110 Communication daughter card (CDC)
- 1120 Fan assembly
- 1130 CPU
- 1140 Bluetooth antenna assembly
- 1150 LCD assembly
- 1160 Keyboard bezel
- 1170 Speaker assembly and microphone cable
- 1180 System board
- 1190 Hard-disk drive slot
- 2000 Ultrabay Plus guide rail
- 2010 I/O Bracket
- 2020 LCD front bezel
- 2030 Inverter card
- 2040 LCD panel and LCD cable assembly
- 2050 Antenna assembly, hinges, and LCD cover
- Locations
- Parts list
- Notices
The
Product
Recovery
program
is
in
a
section
of
your
hard
disk
drive
that
is
not
displayed
by
Windows
Explorer.
Note:
The
recovery
process
might
take
up
to
2
hours.
Attention
All
of
the
files
on
the
primary
hard
disk
partition
(usually
drive
C)
will
be
lost
in
the
recovery
process.
Be
sure
to
back
up
copies
of
the
files
you
have
saved
on
your
drive
C
before
you
begin.
To
use
the
Product
Recovery
program
to
restore
your
pre-installed
software,
do
the
following:
1.
If
possible,
save
all
your
files
and
shut
down
your
operating
system.
2.
Turn
off
your
computer.
3.
Turn
on
your
computer.
Watch
the
display
carefully.
When
the
following
message
is
displayed,
press
the
blue
Access
IBM
button
to
open
the
Access
IBM
Predesktop
Area:
“To
interrupt
normal
startup,
press
the
blue
Access
IBM
button.”
(If
Windows
is
not
running
normally
and
does
not
open,
the
Access
IBM
Predesktop
Area
will
open
automatically.)
4.
Double-click
the
Recover
to
factory
contents.
5.
Follow
the
instructions
on
the
screen.
6.
When
the
Product
Recovery
program
finishes,
your
computer
will
restart
and
begin
the
configuration
process.
Using
the
recovery
CD
To
create
the
service
partition
and
install
the
preloaded
system
from
the
recovery
CD,
do
the
following:
To
create
the
service
partition:
1.
Erase
all
partitions
on
the
hard-disk
drive,
using
FDISK
or
a
similar
application.
2.
Boot
with
the
recovery
CD
(and
the
boot
diskette
if
required.)
3.
Following
message
is
displayed:
“Your
computer
originally
included
a
Product
Recovery
program
...
Reinstall
the
Product
Recovery
program?
(Y/N)
[
]”.
Note:
If
the
hard-disk
drive
contains
any
partitions,
you
do
not
receive
this
message;
go
to
step
1.
4.
Press
Y
key.
The
service
partition
is
created
and
loaded
with
the
Product
Recovery
program
files.
Related
service
information
General
descriptions
29