VENTILATION FAN WITH BLUETOOTH SPEAKER MODEL ITG70BT TABLE OF CONTENTS READ AND SAVE THESE INSTRUCTIONS Address: 46101 Fremont Boulevard, Fremont, CA 94538 US Toll Free Number: 1-888-979-9889 Package Contents 2 General Safety Information 3 Preparation and Wiring Diagrams 5 Assembly Instructions - New Construction 6 Assembly Instructions - Existing Construction 7 Operation 10 Care and Maintenance 11 Troubleshooting 12 Dimensions 13 Product Specifications 13 Warranty 14
PACKAGE CONTENTS 1 2 3 4 Model: ITG70BT 2 PART DESCRIPTION QTY 1 Fan Housing 1 2 Grille 1 3 Duct Connector 1 4 Bluetooth Speaker Assembly 1
GENERAL SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS GENERAL SAFETY INFORMATION 6. Ducted ventilating fans must always be vented to the outdoors. 1. Make sure that the electric service supply voltage is AC 120V, 60Hz. 7. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit lnterrupter) – protected branch circuit. 2.
GENERAL SAFETY INFORMATION WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PREPARATION Tools Required for Assembly (not included): Hammer, Flathead Screwdriver, Wire Nuts, Nails, Duct Tape, Phillips Head Screwdriver, Utility Knife Roof cap (with built-in damper) Short piece of flexible duct helps alignment and absorbs sound Helpful Tools (not included): Electric Drill, Drill Bits Fan housing WARNING: Turn off electricity at breaker box before beginning installation. or Carefully remove unit from carton.
ASSEMBLY INSTRUCTIONS 1 NEW CONSTRUCTION 3 BEFORE INSTALLATION Turn off power source. Review all safety precautions. 1 1. Attach the duct connector 3 to the fan housing 1 . 2 2. Remove the wiring box cover from the fan housing 1 . Remove the wiring knockout from the wiring box cover with a flathead screwdriver (not included). 1 3 3. Place the fan housing 1 next to a ceiling joist or wall stud, The fan housing 1 should be level and perpendicular to the joist or stud. Joist or wall stud 1 4 4.
ASSEMBLY INSTRUCTIONS 6 6. Install a circular 4 in. duct (not included) and secure it with duct tape or clamps (neither included). 4 in. duct Finish ceiling work. The ceiling hole should be aligned with the edge of the fan housing. Duct tape or clamp Ceiling 7 7. Plug the Micro USB connector into the speaker assembly 4 , and secure the speaker assembly to the holder on the fan unit. 4 8. Pinch the mounting springs on the grille 2 , and insert them into the narrow rectangular slots inside the fan.
ASSEMBLY INSTRUCTIONS 3 3. If this fan is not replacing an old fan, be sure to cut a 7 1/2 in. x 7 1/4 in. opening for the fan housing 1 . Make sure the 7 1/4 inch side of opening is flush with the joist for installation from below. 7 71 i /4 n. 4 4. Attach the duct connector 3 to the fan housing 1 . 3 1 5 5. Remove the three screws that hold the fan motor assembly in place. Remove the fan motor assembly from the fan housing 1 . Unplug fan and speaker connector.
ASSEMBLY INSTRUCTIONS 9 9. Mount the fan housing 1 to the joist or stud using nails (not included) where indicated by arrows inside the fan housing 1 . 1 4 inch duct Joist or wall stud Tape Nail 10 10. Plug the fan assembly back into the fan housing 1 .Reattach the fan assembly using the thress screws removed in step 5. 1 FAN CONNECTOR SPEAKER CONNECTOR 11. Plug the Micro USB connector into the speaker assembly 4 , and secure the speaker assembly to the holder on the fan unit.
ASSEMBLY INSTRUCTIONS 12 12. Pinch the mounting springs on the grille 2 , and insert them into the narrow rectangular slots inside the . fan. Push the grille up toward the ceiling. Turn on electricity at the breaker box after finishing installation. 2 OPERATION Fan Mode: Turn the Fan switch to operate ON/OFF. Speaker Mode: Turn the Speaker switch to operate ON/OFF.
CARE AND MAINTENANCE See safety information before proceeding. Routine maintenance should be done at least once a year. • Never use solvents, thinner or harsh chemicals when cleaning the fan. 1 • Do not allow water to enter the motor. • Do not immerse metal parts in water. • Do not immerse resin parts in water over 140º Fahrenheit. • Do not immerse Bluetooth speaker in water. Turn off power source. Review all safety precautions. 1. To remove grille 2 , squeeze springs and pull down. 2.
TROUBLESHOOTING PROBLEM The fan is not turning on The fan seems louder than it should POSSIBLE CAUSE CORRECTIVE ACTION 1. Power off 1. Make sure power supply is on. 2. Faulty switch 2. Test or replace switch. 3. Faulty wire connection 3. Check wire in switch box. 1. CFM too great 1. Be sure the CFM rating on the fan matches the size of your room. 2. Damper not working properly or damaged 2. Check damper to ensure it is opening and closing properly.
DIMENSIONS 9 3/8 4 10 3/4 3/4 5 3/4 UNIT: INCH PRODUCT SPECIFICATIONS SPECIFICATIONS Model No. VFB070B4BT1 ITG70BT Voltage (V) 120 Frequency Fan Power @ 0.1”SP (Hz) (W) 60 8.4 Air Flow @ 0.1”SP (CFM) Weight (lb.) Max. Current (amps) 70 6.7 0.22 Note: Design and specifications subject to change without notice.
WARRANTY DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY Delta Electronics Inc. (“Delta Electronics”) warrants to the original consumer purchaser in the USA and Canada that the Breez ventilation fan products will be free from defects in material or workmanship. This warranty is limited to three (3) years from the original date of purchase. Limitations and Exclusions 1. During the warranty period, a replacement for any defective product will be supplied free of charge for installation by the consumer.
