Instruction Manual
Wiring of DOP-107HS42x / DOP-107HS46x
Cable definition for DOP-107HS42x / DOP-107HS46x series
Color of bare wire
Cable
(twisted pairs are
represented with
identical codes)
Function
White and orange
A
RS422 TX+ / RS485 D+
White and black
-
SG (RS422, RS485)
White and green
B
RS422 RX+ (labelled as “12”)
Brown
-
3-position operation switch – NO(A)
Orange
A
RS422 TX- / RS485 D-
Green
B
RS422 RX-
White and brown
-
3-position operation switch – NO(A)
Red
-
24V
DC
input ( use SELV power supply, isolated from MAINS
by double insulation)
Black
-
0V
DC
input ( use SELV power supply, isolated from MAINS
by double insulation)
White
-
FGND power ground ( use SELV power supply, isolated
from MAINS by double insulation)
Yellow
C
DOP-107HS46x only: output point A of MPG
White and yellow
C
DOP-107HS46x only: output point B of MPG
White and purple
D
Emergency stop – NC(B)
White and green
D
Emergency stop – NC(B)
White and red
-
DOP-107HS46x only: external power input of MPG
Blue
E
Emergency stop – NC(B)
White and blue
E
Emergency stop – NC(B)
Wiring of DOP-107HE46x
Cable definition for DOP-107HE46x series
Color of bare wire
Cable
(twisted pairs are
represented with
identical codes)
Function
RJ45 pin1
A
LAN RD+
White and black
-
Reserved
RJ45 pin3
B
LAN TD+
Brown
-
3-position operation switch – NO(A)
RJ45 pin2
A
LAN RD-
RJ45 pin6
B
LAN TD-
White and brown
-
3-position operation switch – NO(A)
Red
-
24V
DC
input (use SELV power supply, isolated from
MAINS by double insulation)
Black
-
0V
DC
input (use SELV power supply, isolated from MAINS
by double insulation)
White
-
FGND power ground (use SELV power supply, isolated
from MAINS by double insulation)
Yellow
C
DOP-107HE46x only: output point A of MPG
White and yellow
C
DOP-107HE46x only: output point B of MPG
White and purple
D
Emergency stop – NC(B)
White and green
D
Emergency stop – NC(B)
White and red
-
DOP-107HE46x only: external power input of MPG
Blue
E
Emergency stop – NC(B)
White and blue
E
Emergency stop – NC(B)
(7) Basic inspection
Item
Content
General inspection
Periodically check if the screws are securely tightened at the connection between
the HMI and equipment.
If the HMI is installed in a location containing dust or harmful gas, take precautions
to prevent the dust and harmful gas from entering the HMI.
Inspection before
operation
(without power)
Ensure the communication wiring is correct, or it may cause abnormal operation.
Ensure there is no electrically conductive objects, such as screws or sheet metal, or
inflammable objects inside or near the HMI.
Reduce the electromagnetic interference if there is electromagnetic interference
with the peripheral devices.
Ensure the external voltage level for the HMI is correct.
Inspection before
operation
(power is applied)
Check if the power indicator is enabled.
Check if the communication among equipment is functioning normally.
If the HMI operates abnormally, contact the local distributors or Delta Customer
Service Center.
(8) Output description of MPG
Electrical specifications
Input voltage (white and red wire)
Output current
DC 5V +/- 5%
20 mA (Max.)
DC 24V +/- 5%
30 mA (Max.)
Configuration
107H cable
Yellow
White and
yellow
Device
White
and red
DC5V / DC24V
A
B
Note:
1. If connecting more than one devices for MPG control is required, connect them according to the electrical
specifications for MPG output to avoid malfunction.
2. DC 5V and DC 24V devices that receiving pulses are supported. Ensure the device complies with the required
voltage, or it may cause damage to the equipment.
(9) Hardware specifications
Model
DOP-107HS42x
DOP-107HS46x
DOP-107HE42x
DOP-107HE46x
DOP-107HE47xZD
DOP-107HE42xZM
DOP-107HE46xZM
Display
Panel type
7" TFT LCD (65535 colors)
Resolution
800 x 480 pixels
Backlight
LED backlight (half-life under room temperature 25°C > 20,000 hours)
(Note 1)
Display size
154.08 x 85.92 mm
CPU
ARM Cortex-A8 (800 MHz)
Flash ROM
256 Mbytes
RAM
256 Mbytes
Non-volatile memory
32 Kbytes
Touch panel
4-wire resistive touchscreen
> 10,000,000 operated
Buzzer
Multi-tone frequency (2 to 4 kHz) / 80 dB
Network interface
N/A
10/100 Mbps auto-detection (built-in isolated power circuit)
(Note 2)
Serial communication
port
RS422 / RS485
(Note 2)
N/A
Memory card
SD / SDHC
USB
1 USB client Ver 2.0
Emergency stop
switch
B contact x 2
A contact x 1 / B contact x 1
Rated voltage: < DC 30V
Maximum rated current: 1A
Minimum allowable load: DC 5V / 1 mA
Complies with IEC60947-5-1, EN60947-5-1, IEC60947-5-5, EN60947-5-5, UL 508,
CSA C22.2 No.14, GB 14085.5
3-position operation
switch
A contact x 1
Rated voltage: < DC 30V
Maximum rated current: 700 mA
Minimum allowable load: DC 3V / 5 mA
Complies with EN/IEC60947-5-8, IEC60947-5-1, EN60947-5-1, JIS C8201-5-1, UL508,
CSA C22.2 NO. 14
Applicable standards for use with ISO12100-1,-2/EN12100-1, -2, IEC60204-1/EN60204-1,
ISO11161/prEN11161, ISO10218/EN775, ANSI/RIA R15.06, ANSI B11.19
MPG
The MPG function is not available on DOP-107HE42x, DOP-107HS42x, and DOP-
107HE42xZM models.
Rated voltage: < DC 24V
Resolution: 50(P/R)
Output waveform: square wave
Output phase: A, B
Phase difference between A and B: 90° ± 45°
Maximum frequency response: 200 Hz
Auxiliary keyboard
DOP-107HE47xZD : 21 function keys ;
DOP-107HE42x / DOP-107HE46x / DOP-107HE46xZM / DOP-107HS42x / DOP-107HS46x / :
15 function keys
Cable length
5 m (when end of model name = 5)
10 m (when end of model name = A)
Calendar
Built-in
Cooling method
Natural cooling
Safety approval
CE
(Note 3)
Protection rating
IP54
Operating voltage
DC +24V (±15%) (built-in isolated power circuit)
(Note 2)
(supplied by SELV circuits (isolated from MAINS by double insulation))
Leakage current
AC500V for one minute (between DC24 and FG terminals)
Power consumption
4.896 W
(Note 4)
Backup battery
3V lithium battery CR2450 × 1
Backup battery life
About 5 years or more at 25°C (77°F)
(subject to operation temperature and condition)
Operation
temperature
0°C to 40°C (32°F to 104°F)
Storage temperature
-10°C to +60°C (14°F to 140°F)
Operating
environment
10% to 90% RH [0 to 40°C (32 to 104°F) ], 10% to 55% RH [41 to 50°C (105.8 to 122°F) ]
pollution degree: 2
Vibration resistance
Conforms to IEC61131-2: continuous vibration 5 Hz to 8.3 Hz with amplitude 3.5 mm; 8.3 Hz to
150 Hz with amplitude 1G
Shock resistance
Conforms to IEC60068-2-27: 11 ms, 15G Peak , in X, Y, Z directions each for 6 times
Dimensions
(W) x (H) x (D) mm
257.4 x 170.3 x 71.8 (emergency stop switch and hook included)
Weight
750 g (cable excluded)
Note:
1. The half-life of the backlight is defined as the maximum luminance being reduced by 50% when the maximum drive
current is supplied to the HMI. The life of LED backlight shown here is estimated at the room temperature of 25°C
(77°F) with ambient humidity.
2. The withstand voltage of the isolated power circuit is 1500V peak for 1 minute.
3. The certification for some models is under application. Contact the local distributor for the certificated models.
4. The HMI power consumption is the power consumed when the HMI is not connecting with other peripheral devices.
To ensure normal operation of the HMI, the recommended capacity of the power supply is 1.5 to 2 times of the
specified power consumption.
5. Isolated power supply unit is suggested.
6. You can download the DOP-107H series programming software DOPSoft, user manual, and HMI installation sheet
from Delta’s website. The instruction sheet may be revised without prior notice. Download the latest version from
the Delta website (http://www.deltaww.com).
7. The DOP-107H series products can be used with industrial automation equipment. Read though this instruction
sheet carefully and install the product according to the instructions to avoid danger.
8. Cleaning method: use a dry cloth to clean the product.
9. For repair and maintenance, contact Delta Electronics, Inc. Address: No. 18, Xinglong Rd., Taoyuan City, Taiwan.
TEL: +886-3-3626301.