Installation Guide

ManualsBrandsDelta ManualsKitchenKine Single-Handle Pull-Out Sprayer Kitchen Faucet with Soap Dispenser in SpotShield Stainless

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/

Articles dont vous pouvez avoir besoin:

Para instalación fácil de su llave Delta

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

For easy installation of your Delta

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

Pour installer votre robinet Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant de débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

Models/Modelos/Modèles

16967-SD-DST

Series/Series/Seria

KINE

™

SILICONE

Icons

3/10/15 Rev. Awww.deltafauet.com

WARNING: THIS FAUCET IS NOT TO BE USED WITH PORTABLE

DISHWASHERS!

ADVERTENCIA: ¡SESTA LLAVE NO SE DEBE UTILIZAR CON MAQUINAS

LAVAPLATOS PORTATILES!

AVERTISSEMENT: ON NE DOIT PAS BRANCHER UN LAVE-VAISSELE

PORTATIF SUR CE ROBINET!

SINGLE HANDLE PULLOUT KITCHEN FAUCET

LLAVE EXTRAÍBLES DE AGUA PARA COCINAS

ROBINET À UNE MANETTE À BEC-DOUCHETTE

RÉTRACTABLE POUR ÉVIERS DE CUISINE

SILICONE

Icons

78958

1/8" (3.17mm)

Summary of content (12 pages)

PAGE 1
SINGLE HANDLE PULLOUT KITCHEN FAUCET LLAVE EXTRAÍBLES DE AGUA PARA COCINAS ROBINET À UNE MANETTE À BEC-DOUCHETTE RÉTRACTABLE POUR ÉVIERS DE CUISINE 78958 Models/Modelos/Modèles 16967-SD-DST Series/Series/Seria KINE™ Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
1 B. A. C. A. 1 1 2 B. 2 3 1 3 1 1 3 1 2 2 2 Faucet Installation Faucet Installation DECK MOUNT STYLE A. Place baseplate shanks (1) through mounting holes in deck. Option: If sink is uneven, use silicone sealant under the baseplate. 2 CENTER MOUNT STYLE C. Secure faucet to sink with mounting nut and washer (1). Tighten securely by hand. Using a Phillips screwdriver, tighten locking screws (2). Install locknuts (3) and hand-tighten. A. Install square escutcheon (1) onto faucet (2).
PAGE 3
2 B. A. 2 OR 1 O 3 2 OU 3 4 2 1 1 4 A. Water Line Connections Ensure all fittings and end connections are free of debris. Faucet fittings (1) are 3/8" compression, with ends colored red for hot and blue for cold. Loop tubing (2) if it is too long. Note: Recommended tubing minimum bend diameter is 8". Secure metal nut (3) on faucet tube to supply valve connection (4) and hand tighten, then tighten one additional turn with wrench. DO NOT OVERTIGHTEN. Repeat for other tube.
PAGE 4
Correct method Método Correcto Bonne méthode Incorrect Installation Instalación Incorrecta Installation Incorrecte 2 3 1 4 Custom Fit Connections - Plastic Sleeve Installation Instructions 1. Identify desired length of tube (1). Leave 1" - 2" of extra length to allow for easier installation and cut tube. Ensure cut is straight and burr free. 2. Slide nut (2) and plastic sleeve (3) onto cut tube. Ensure sleeve is oriented as shown. 3. Insert tube into outlet fitting (4).
PAGE 5
3 1 2 Because your sprayer has been factory assembled to the hose, we do not recommend removing to flush the lines. Instead, if possible, we recommend placing a bucket below the outlet fitting and one of two options: 2. With the supply stops open (2), slowly open and close the handle in the mix open position (1). This will prevent debris from being lodged in the hose and sprayer. 1. With the valve in mix open position (1), slowly open and close the supply stops (2).
PAGE 6
4 B. A. 1 2 1 2 3 3 2 1 2 4 3 1 3 2 3 1 Incorrect Installations. Hose Installation A. Pass hose (1) through faucet (2). Slide hose weight Instalacións incorrecta. B. Push hose end (1) onto faucet outlet (2). Attach Installations incorrecte. (3) over end of hose (4). clip (3) over hose and outlet as shown. Pull down moderately to ensure connection has been made. Instalación de la Manguera A. Pase la manguera (1) por la llave de agua (2).
PAGE 7
5 6 2 6 3 4 1 5 Soap Dispenser Installation Remove nut (1). Separate head (2) from body (3). Insert body (3) and gasket (4) through selected hole in sink. Make sure gasket (4) is properly seated in the base. Secure body to sink with nut (1). From under the sink screw the bottle (5) onto the body assembly shank. Insert pump (6) into head (2), then drop into body (3). Check all connections at arrows for leaks. Refer back to the appropriate installation instructions and retighten if necessary.
PAGE 8
7 1 2 Setting The Handle Limit Stop (Optional) This faucet includes an integrated handle limit stop that has two positions. Position 1, to the left, allows full handle motion (the full range between “all cold” to “all hot”). The faucet is set in position 1 in the factory. Position 2, to the right, allows half of the normal handle motion (“all cold” to “mixed hot/cold”). The handle limit stop can be adjusted by the homeowner once the faucet is installed.
PAGE 9
Backflow Protection System Your Delta Faucet pull-out spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1. It incorporates two certified check valves in series, which operate independently and are integral, non-serviceable parts of the wand assembly.
PAGE 10
16967-SD-DST Model / Modelo / Modèle RP152 Set Screw Tornillo de Presión Vis de calage RP81299▲ Lever Handle & Set Screw Manijas de Palanca Tornillo de Presión Manette et vis de calage RP28906 Button / Botón / Bouton RP51502▲ Cap Casquillo Embase RP81301▲ Wand Assembly Ensamble de la Cabeza del Rociador Bec-douchette RP51503 Bonnet & V-Ring Bonete y Aro-V Chapeau et joint à lèvres RP50587 Valve Assembly Ensamble de la válvula Soupape RP81300▲ Hub Assembly Ensamble de Cubo Boîter RP32529▲ Aerator Airea
PAGE 11
RP47888 Bottle & Pump Bottela y Bomba Bouteille et pompe RP63263 Adapters 3/8"-24 UNEF to 1/2"-20 UN & 3/8"-24 UNEF to 1/2"-14 NPSM Adaptadors 3/8"-24 UNEF a 1/2"-20 UN & 3/8"-24 UNEF a 1/2"-14 NPSM Adapteurs 3/8 po-24 UNEF à 1/2 po-20 UN et 3/8 po-24 UNEF à 1/2 po-14 NPSM RP21945 Nut Tuerca Écrou RP63264 Adapters (10) 3/8"-24 UNEF to 1/2"-20 UN Adaptadors (10) 3/8"-24 UNEF a 1/2"-20 UN Adapteurs (10) 3/8 po-24 UNEF à 1/2 po-20 UN RP81410▲ Dispenser Assembly Ensamble del Dispensador Distributeur www.
PAGE 12
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.