User's Manual
Table Of Contents
- Electrical Safety and Emissions Standards
- Translated Safety Statements
- Contents
- Figure 1: AT-WA7400 Wireless Access Point 21
- Figure 2: Front and Back Panels 21
- Figure 3: Location of the Antenna Connectors 31
- Figure 4: Attaching the Antennas 31
- Figure 5: Attaching the Rubber Feet 33
- Figure 6: Aligning the Access Point for Mounting on the Wall 35
- Figure 7: Attaching the Magnets 36
- Figure 8: Attaching the LAN Cable 37
- Figure 9: Connecting the Power Adapter 38
- Figure 10: PoE Connection 39
- Figure 11: CD Main Menu 40
- Figure 12: KickStart Welcome Dialog Box 41
- Figure 13: KickStart Search Results Dialog Box 42
- Figure 14: Administration Dialog Box 43
- Figure 15: Login Dialog Box 43
- Figure 16: Basic Settings Page 44
- Figures
- Tables
- Contents
- Translated Safety Statements
- Preface
- Chapter 1
- Overview
- Chapter 2
- Installation
- Reviewing Safety Precautions
- Installation Guidelines
- Unpacking the Access Point
- Installing the Antennas
- Using the Access Point on a Desktop
- 1. Turn the access point over so that the top is resting on a flat surface.
- 2. Attach the four rubber feet to the bottom of the access point as shown in Figure 5.
- 3. Turn the access point over and place it on a flat, secure surface such as a desk or table, leaving ample space around the unit for ventilation.
- Mounting an Access Point on a Wall
- 1. Select a wall location and mark two hole locations for the anchors 98.425 mm (3.875 in.) apart.
- 2. At the two marked hole locations, pre-drill for the drywall anchors.
- 3. Install the anchors and drive the screws into the anchors leaving approximately 4.76 mm (.1875 in.) exposed.
- 4. Align the keyholds on the back with the screw heads, as shown in Figure 6.
- 5. Place the keyhole slots on the bottom of the access point over the screw heads.
- 6. Slide the access point down onto the screw heads so that the access point is securely mounted on the wall.
- Mounting the Access Point on a Metal Surface
- Connecting the Access Point to the LAN
- Powering On the Access Point
- Starting a Management Session
- 1. Do one of the following to create an Ethernet connection between the access point and your computer:
- 2. Insert the AT-WA7400 Wireless Access Point CD into the CD- ROM drive on your computer.
- 3. Click KickStart Utility.
- 4. Click Next to search for access points.
- 5. Review the list of access points that KickStart found, as shown in the example in Figure 13.
- 6. Verify the MAC address shown with the hardware label on your AT-WA7400 Wireless Access Point(s).
- 7. Click Next.
- 8. Click Administration.
- 9. Enter the user name and password and click OK.
- Warranty Registration
- Chapter 3
- Troubleshooting
- Appendix A
- Technical Specifications
77
Electrical Safety and Emissions Standards ..................................... 3
Translated Safety Statements ............................................................... 5
Preface .............................................................................................. 13
Safety Symbols Used in this Guide ..................................................... 14
Where to Find Web-based Guides ...................................................... 15
Contacting Allied Telesyn.................................................................... 16
Online Support ............................................................................ 16
Email and Telephone Support..................................................... 16
Returning Products...................................................................... 16
Sales or Corporate Information ................................................... 16
Management Software Updates.................................................. 16
Chapter 1: Overview ......................................................................... 19
Features .............................................................................................. 20
Front and Back Panels ........................................................................ 21
LEDs.................................................................................................... 22
Chapter 2: Installation ...................................................................... 25
Reviewing Safety Precautions............................................................. 26
Installation Guidelines ......................................................................... 28
Microwave Ovens........................................................................ 28
Cordless Telephones .................................................................. 29
Other Access Points.................................................................... 29
Unpacking the Access Point................................................................ 30
Installing the Antennas ........................................................................ 31
Using the Access Point on a Desktop ................................................. 33
Mounting an Access Point on a Wall................................................... 34
Mounting the Access Point on a Metal Surface................................... 36
Connecting the Access Point to the LAN ............................................ 37
Powering On the Access Point............................................................ 38
Starting a Management Session ......................................................... 40
Contents