User's Manual
Table Of Contents
- Electrical Safety and Emissions Standards
- Translated Safety Statements
- Contents
- Figure 1: AT-WA7400 Wireless Access Point 21
- Figure 2: Front and Back Panels 21
- Figure 3: Location of the Antenna Connectors 31
- Figure 4: Attaching the Antennas 31
- Figure 5: Attaching the Rubber Feet 33
- Figure 6: Aligning the Access Point for Mounting on the Wall 35
- Figure 7: Attaching the Magnets 36
- Figure 8: Attaching the LAN Cable 37
- Figure 9: Connecting the Power Adapter 38
- Figure 10: PoE Connection 39
- Figure 11: CD Main Menu 40
- Figure 12: KickStart Welcome Dialog Box 41
- Figure 13: KickStart Search Results Dialog Box 42
- Figure 14: Administration Dialog Box 43
- Figure 15: Login Dialog Box 43
- Figure 16: Basic Settings Page 44
- Figures
- Tables
- Contents
- Translated Safety Statements
- Preface
- Chapter 1
- Overview
- Chapter 2
- Installation
- Reviewing Safety Precautions
- Installation Guidelines
- Unpacking the Access Point
- Installing the Antennas
- Using the Access Point on a Desktop
- 1. Turn the access point over so that the top is resting on a flat surface.
- 2. Attach the four rubber feet to the bottom of the access point as shown in Figure 5.
- 3. Turn the access point over and place it on a flat, secure surface such as a desk or table, leaving ample space around the unit for ventilation.
- Mounting an Access Point on a Wall
- 1. Select a wall location and mark two hole locations for the anchors 98.425 mm (3.875 in.) apart.
- 2. At the two marked hole locations, pre-drill for the drywall anchors.
- 3. Install the anchors and drive the screws into the anchors leaving approximately 4.76 mm (.1875 in.) exposed.
- 4. Align the keyholds on the back with the screw heads, as shown in Figure 6.
- 5. Place the keyhole slots on the bottom of the access point over the screw heads.
- 6. Slide the access point down onto the screw heads so that the access point is securely mounted on the wall.
- Mounting the Access Point on a Metal Surface
- Connecting the Access Point to the LAN
- Powering On the Access Point
- Starting a Management Session
- 1. Do one of the following to create an Ethernet connection between the access point and your computer:
- 2. Insert the AT-WA7400 Wireless Access Point CD into the CD- ROM drive on your computer.
- 3. Click KickStart Utility.
- 4. Click Next to search for access points.
- 5. Review the list of access points that KickStart found, as shown in the example in Figure 13.
- 6. Verify the MAC address shown with the hardware label on your AT-WA7400 Wireless Access Point(s).
- 7. Click Next.
- 8. Click Administration.
- 9. Enter the user name and password and click OK.
- Warranty Registration
- Chapter 3
- Troubleshooting
- Appendix A
- Technical Specifications
Chapter 2: Installation
30
Unpacking the Access Point
To unpack the AT-WA7400 Wireless Access Point, perform the
following procedure:
1. Remove all components from the shipping pckage.
Note
Store the packing material in a safe location. You must use the
original shipping material if you need to return the unit to Allied
Telesyn.
2. Place the access point on a secure, level surface.
3. Ensure that the following hardware components are included in your
access point packge. If any item is missing or damaged, contact your
Allied Telesyn sales representative for assistance.
One AT-WA7400 Wireless Access Point
Two antennas
One wall mount kit containing two wall anchors and two screws
One AC adapter
One RJ45 managment cable
Four rubber feet
One magnet kit containing four magnets and four screws
One documentation CD with KickStart utility
This installation guide
Warranty card