User Manual

4 AT-TQ 2403 - IEEE 802.11abgh, D ual Radio, Enterprise W ireless Access Point - Installation Guide
ELECT RICAL SAFETY AN D EMISSION S ST AN DARDS
This product meets the following standards.
U.S. Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
For operation within 5.15 ~ 5.25GH z frequency range, it is restricted to indoor environment.
T his device complies with Part 15 of t he FCC Rules. O peration is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at
the factory to match the intended destination. The firmware setting is not accessible by the end user.
FCC
Caution: This equipment complies with Part 15E of the FCC Rules with radar detection function and D FS capability. O peration is
subject to the following three conditions:
(1) This device is intended to use indoor operations only.
(2) This device will not permit operations on channels which overlap the 5600 - 5650 MHz band.
(3) This device meets all the other requirements specified in Section 15.407 and no configuration controls are provided to change the
frequency of operations outside the grant of certification for US operation.
Canadian Department of Communications
This device complies with RSS-210 of the Industry Canada Rules. O peration is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Caution: The device for the band 5150-5250 MH z is only for indoor usage to reduce potential for harmful interference to
co-channel mobile satellite systems.
High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MH z and 5650-5850 MH z and these radars
could cause interference and/or damage to LE-LAN devices.
This device has been designed to operate with an antenna having a maximum gain of [x] dB. Antenna having a higher gain is strictly
prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.
CE Marking W arning
This device complies with the essential requirements of the R&TTE D irective 1999/5/EC. The following test methods have been applied
in order to prove presumption of conformity with the essential requirements of the R&TTE D irective 1999/5/EC:
EN 60950-1: 2006
Safety of Information Technology Equipment
EN 50385: 2002