User Manual

ManualsBrandsDelta Networks ManualsElectronicsWireless LAN Module

Wireless PCMCIA card

Installation Guide

For OEM integrator

Federal Communications Commission (FCC) Compliance

Notice: Radio Frequency Notice

This device, Wireless PCMCIA Card (LM-WP210RB), must

be installed and used in strict accordance with the

manufacture’s instructions as described in the user

documentation that comes with the product.

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following

measures: (1) Reorient or relocate the receiving antenna, (2)

Increase the separation between the equipment and receiver, (3)

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected, (4) Consult the dealer

or an experienced radio/TV technician for help.

Summary of content (15 pages)

PAGE 1
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This device, Wireless PCMCIA Card (LM-WP210RB), must be installed and used in strict accordance with the manufacture’s instructions as described in the user documentation that comes with the product. Wireless PCMCIA card Installation Guide For OEM integrator This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2.
PAGE 2
Wireless PCMCIA card Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. CAUTION: This device is intended only for OEM integrators under the following conditions: 1. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
PAGE 3
Wireless PCMCIA card Wireless PCMCIA card TABLE OF CONTENT Introduction Driver Installation 1 2 Install Driver Under Windows XP 2 Install Driver Under Windows 98 6 Install Driver Under Windows ME 10 Install Driver Under Windows 2000 12 Install Driver Under Windows CE 18 Configure the Configuration Utility 21 Introduction The Wireless PC card helps you create a wireless network for sharing your broadband cable or DLS internet access among multiple PCs in and around your home of office.
PAGE 4
Wireless PCMCIA card Driver Installation Wireless PCMCIA card 2. Windows will notify you that it has not passed Windows Logo testing to verify its compatibility with Whistler. Click the Continue Anyway button to continue. 3. At this point, the Configuration screen appears. Configure the PCMCIA card and then click the OK button. Install Driver Under Windows XP 1. 2 Connect the Wireless PC card into your Notebook PC. Windows XP will automatically recognize a new Wireless 802.11b PCMCIA Card 2.5.
PAGE 5
Wireless PCMCIA card 4. 4 On the Encryption screen, set the WEP. Windows has now completed installing the network. Click the Finish button to continue. Wireless PCMCIA card 5. Click right on My computer and select properties. Select Device Manager and click on the Network adapters. You will find the Wireless 802.11b PCMCIA Card 2.5 if it is installed successfully. The PC card adapter driver installation is finished.
PAGE 6
Wireless PCMCIA card Install Driver Under Windows 98 1. Connect the Wireless PC card into your Notebook PC. Windows 98 will automatically recognize a new Wireless 802_11bPCMCIA Card 2_5. Click the Next button to proceed. 2. Make sure Search for the best driver for your device is selected and click the Next button. 6 Wireless PCMCIA card 3. Make sure the Specify a location is selected and click the Browse button. At this point, Windows will ask you to browse for the folder.
PAGE 7
Wireless PCMCIA card 5. 6. 8 At this point, the Properties screen appears. Configure the PCMCIA card and then click the OK button. Wireless PCMCIA card 7. After installing the drivers, the System Setting Change screen will show you that installation is complete. Click the Yes button to finish. 8. Click right on My computer and select properties. Select Device Manager and click on the Network adapters. You will find the Wireless 802.11b PCMCIA Card 2.5 if it is installed successfully.
PAGE 8
Wireless PCMCIA card Install Driver Under Windows ME 1. 2. 10 Wireless PCMCIA card 3. Windows will notify that installing has been completed. Click the Finish button to continue. 4. Windows will now ask you to restart your computer. Click the Yes button to restart. Windows automatically recognizes a new PC Card added. Select Automatic search for a better driver [Recommended] and click the Next button to proceed. At this point, the Properties screen appears.
PAGE 9
Wireless PCMCIA card 5. To verify the driver installation, Move cursor on “My computer” icon and click the right button of the mouse. Select the properties. The System Properties windows shows. Click the Network adapters on the Device Manager folder. Wireless 802.11b PCMCIA Card 2.5 will be found if the driver installation is successful. Wireless PCMCIA card 1. Windows 2000 will automatically recognize the PC Card, once it is connected to the PC, and prompt you to install the necessary driver.
PAGE 10
Wireless PCMCIA card Wireless PCMCIA card 3. Select Specify a location and click the Next button. 5. Windows will now search for the driver. After Windows acknowledges finding the driver, click the Next button. 4. In the field, type the folder in which the driver files are located and then click the Next button. 6. The Digital Signature Not Found screen is a notification by Windows 2000. However, this does not mean that there is a problem. Click the Yes button to continue.
PAGE 11
Wireless PCMCIA card 6. The Configuration screen appears. Configure the PCMCIA card and then click the OK button. 7. Set the WEP on the Encryption screen. Windows will now install the driver files. Click the Finish button when completed. 16 Wireless PCMCIA card 8. Click right on My computer and select properties. Select Hardware and select Device Manager and click on the Network adapters. You will find the Wireless 802.11b PCMCIA Card 2.5 if it is installed successfully.
PAGE 12
Wireless PCMCIA card Install Driver Under Windows CE The PCMCIA card driver is installed with configuration utility automatically while the PCMCIA card is installed on your PDA. 1. 2. 18 Wireless PCMCIA card 3. Software License Agreement screen appears. Read the entire agreement by clicking the Page Down button on your keyboard. Click the Yes button if you agree, or No if you disagree. Clicking No will terminate the installation. If you click Yes, the installation will continue. 4.
PAGE 13
Wireless PCMCIA card 6. Once the installation wizard is complete, click the Finish button. Wireless PCMCIA card Configure the Configuration Utility STATUS The Status screen provides information about the current link between the PC Card and the wireless Access Point. The Current Channel field shows to what channel the PC Card is set. The Current Tx Rate field shows the transfer rate in megabits per second. The Throughput fields show the rate at which data is transferred and received in Bytes per second.
PAGE 14
Wireless PCMCIA card CONFIGURATION The Configuration screen allows you to customize the setting for the PC Card and your wireless network. Wireless PCMCIA card The Transmit Rate field shows the current transfer rate for the PC Card. To optimize performance and range, the Transmit Rate should be set to Fully automatic, which will automatically adjust the transfer speed for best performance and longest range. Power Saving Enabled, enables or disables the power saving features of your PC Card.
PAGE 15
Wireless PCMCIA card Wireless PCMCIA card characters. Installation for Access Point Manufacturer WEP must be enabled from the Configuration screen in order to set the 64/128-bit key. To generate an encryption key: Align the wireless LAN card toward the PCMCIA slot of Access Point. Push evenly and steadily until it is seated. 1. 2. 3. 4. Type exactly the same case sensitive PassPhrase in the PassPhrase field. Alphanumeric will transfer the 5 characters to ASCII code.