The user manual of the HD Pocket Projector Product name: HD Pocket Projector Trade: VIVITEK Mode: Q3PLUS FCC ID: H79Q3PLUS User Manual
Foreword Copyright ©2015 Vivitek is a trademark of Delta Electronics, Inc. All other trademarks are the property of their respective owners. All values, weights and sizes in this Manual are approximate values. Specifications are subject to change without notice. Disclaimer The information in this Manual is subject to change without notice.
Important Safety Information Important: It is strongly recommended to read this part before usage of Qumi. These safety and usage instructions will ensure a safe usage of Qumi for several years. Please keep this Manual properly for future reference. Symbols A warning symbol, either on the machine or in this Manual, denotes a hazard. The following symbols are used to call attention to important information. Note: Indicate additional information besides the topic.
Installation Precautions y Leave at least 500mm surround the air outlet. y Ensure that the air inlet will not take any hot gas from the air outlet. y When Qumi is used in a confined space, ensure that the ambient temperature will not exceed the working temperature of Qumi and the air inlet and outlet are unclogged. y Every confined space should pass through professional thermal evaluation to avoid circulation during Qumi exhaust.
Power supply safety y Only use supplied adapter. y Do not place any objects on the power supply cables. Place the power supply cables at proper places to avoid tread. y If the machine is stored or out of service for a long time, please get the battery out of the remote controller. Qumi Cleaning y Before cleaning, disconnect the power supply cables. See “Qumi Cleaning” in Page 39. Note: After usage, Qumi will become a bit hot. Cool Qumi down before putting it into the cabinet.
Table of Contents Foreword ..................................................................................................................................................ii Chapter 1 Views.......................................................................................................................................... 1 Views .......................................................................................................................................................
Chapter 1 Views Views Front/Top/Right view 1
Rear/Top/Left view Bottom view 2
Stan ndard acccessories: Q Qumi accessoories include:: Remoote controller (with a 3VCR R2025 batterry) Powerr supply cablle and adapterr (based on reegions) ment kit (Useer Manual, Quick Start, W Warranty Card d) Docum Standdard HDMI caables F For any item missing, app pearance dam mage or machiine failure, please contact your dealer. Please kkeep original packaging materials m propperly for repaiiring purposee.
Remote controller 4
Set remote controller The remote controller has one (1) 3V lithium battery (CR2025). The battery is preassembled in the remote controller. Before usage of the remote controller, get the plastic sheet (A) out of the battery compartment. Change remote controller battery 1. Get the groove stuck and rotate (A) in the arrow direction, and open the battery compartment cover (B). 2. Take out the old battery and install a new one (positive upwards). 3. Rotate and install the cover in the arrow direction.
Chapter 2 Start to Use What you need Qumi can be connected to several types of external and peripheral equipment. To play music, connect Qumi to an external or portable music player. To play films, connect Qumi to DVD, VCD or VHS player. To play video and display photos, connect Qumi to video camera and digital camera. To display files and other types of media, connect Qumi to peripherals like computer and USB drive. Those devices can be connected to Qumi through corresponding cables.
Set Qumi Connect peripherals through HDMIconnection peripherals to Qumi through cables (optical).
Connect a USB drive Connect a storage device (like a USD drive) to corresponding port for connection to Qumi. Audio output/AV Connect a headset or a mini loudspeaker to the audio output jack for connection to Qumi.
Charge battery After outage, charge the projector in the steps below: Connect the AC adapter to Qumi. Connect the other end of AC adapter to a wall outlet. During charging, at the receiver of remote controller, the blue light will be on. After full charge, the blue light will be off. Note: The battery will be fully charged after 3-4h.
Power on/off Qumi 1. Connect the AC adapter to Qumi. Connect the other end of AC adapter to a wall outlet. Note: The adapter models may differ over region. 2. Press power button to power on Qumi. When AC is connected, hold 1 second. When AC is not connected, hold 5 seconds. Qumi displays startup screen and detects all connected devices.
3. a connectedd, press the SO OURCE If several inpput devices are (signal sourcce) button on n the remote controller an nd select appropriate device d throug gh ▲ or ▼ buutton. y HDMI:H HDMI/DVI y USB1:U USB disc y USB2:U USB disc 4. Press 5. When “Pow wer off? Pleasse press the ppower button n again” p power button to power offf Qumi. message apppears, press is powered off. o power bbutton.
Happy cast- Android operation Screen mirror -Android Operation I: Turn on Happycast and scan the two-dimensional code with an Android phone to download and install the Mobile Version Happycast; Turn on the Projector Setting - General - More - Portable Hotspot - Portable WLAN Hotspot; Conform the portable WLAN hotspot with a tick √.
Operation II: Ensure that the mobile phone and the projector are under a same WiFi environment; Turn on Happycast and scan the two-dimensional code with an Android phone to download and install the Mobile Version Happycast; Turn on the mobile Happycast screen, and click device matched to the projector name (as shown below) for screen mirror operation.
Happy cast-iOS operation Screen mirror -iOS Operation I: Turn on the Projector Setting - General - More - Portable Hotspot - Portable WLAN Hotspot; Conform the portable WLAN hotspot with a tick √. Turn on the projector Happycast; ensure that the mobile phone is connected to the projector WiFi, slide up from the bottom of mobile phone screen to appear the console interface. Click Airplay button to select the device to be projected.
Operation II: Ensure that the mobile phone and the projector are under a same WiFi environment; Turn on the projector Happycast; slide up from the bottom of mobile phone screen to appear the console interface. Click Airplay button to select the device to be projected. Turn on the mirror image switch (as shown below) for screen mirror operation.
Chapter 3 Qumi User Interface Views Qumi user interface (UI) is designed for setting and convenient operation. UI enables a complete medium experience by accessing medium files via smart devices (phones or pads) or USD drives. UI mainly comprises nine functions: y Photo - display photo and provide slide function; the available images in connected USBdrives or devices are listed in the “Photo” menu.
Photo All available images in connected USB drives or devices are listed in the “Photo” menu. Open Image - Select Viewing mode. Press , , and buttons on the remote controller to select files and press for display. The control panel display will change based on the file. The table below lists available functions. Menu bar/Icon 1. Description Photo Album, Place, Time, Figure, Tag Select photo album, Allow offline viewing, Refresh Slide view, Network view 2.
Video Play film files; the available videos in connected USB drives or devices are listed in the “Video” menu. Open video -- Select local disk/USB -- Click the video for display Press , , and buttons on the remote controller to select files and press for display. The control panel display will change based on the file. The table below lists available functions.
Music Play audio files; the available music files in connected USB drives or devices are listed in the “Music” menu. Open Music --, including five categories: Musician, Album, Song, Playlist and Playing. Press , , and buttons on the remote controller to select files and press for display. The control panel display will change based on the file. The table below lists available functions.
Files Play the files; the available files in connected USB drives or devices are listed in the “File” menu. Open the file -- Open -- Local directory -- Select file for opening Press , , and buttons on the remote controller to select files and press for display. The control panel display will change based on the file. The table below lists available functions.
APP Store Manage downloads, updates and accesses to the APPStore. Open APP Store -- Click Search the desired APP.
Browser Display HTML files of the web page servers or file systems (an application for standard and general markup languages) and achieve user-file interaction. Press , , and buttons on the remote controller to select files and press for display. The control panel display will change based on the file. The table below lists available functions.
Application program Manage and operate all application program settings related to QUMI.
WiFi Achieve mutual wireless connection among PC, portable devices (e.g., PAD, mobile phone) and other terminals. Enable WiFi -- Select network name Input password -- Click Connect Press , , and buttons on the remote controller to select files and press for display. The control panel display will change based on the file. The table below lists available functions.
Setting Access to Display, Audio file, Wireless linkage, Bluetooth, Memory, General, Application and System. Press , , and buttons on the remote controller to select files and press for display. The control panel display will change based on the file. The table below lists available functions.
Chapter 4 OSD Setting OSD menu control Qumi has an OSD (on screen display) setting menu for adjusting and changing settings, like display setting and audio setting. OSD menu has 10 sub-menus: y Menu language - set language display formats of the system. Press OK for entry. Select and move to the desired language by Arrow Keys and then press MENU key or Exit to exit. y Display mode - adjust brightness, saturation, sharpness and contrast of the screen display. Press OK for entry.
OSD menu overview The following figure allows you to quickly find a certain setting or confirm its scope.
Setting OSD menu language Menu language of OSD may be changed. Perform the following steps to change the menu language: 1. Press the Screen Display Control Key on remote controller and enter OSD menu. 2. Move the cursor to highlight the menu language, and press . 3. Press , , and buttons until the target menu language is highlighted by cursor and setting of menu language is completed. 4. Press button to close OSD.
Setting display mode Display mode of OSD may be changed. Perform the following steps to change the display mode: 1. Press the Screen Display Control Key on remote controller and enter OSD menu. 2. Move the cursor to highlight the display mode, and press . 3. Press and buttons until the target display mode (Bright, Demo, Film and User) is highlighted by cursor and setting of display mode is completed. 4. Press button to close OSD.
Setting audio mode Audio mode of OSD may be changed. Perform the following steps to change the audio mode: 1. Press the Screen Display Control Key on remote controller and enter OSD menu. 2. Move the cursor to highlight the audio mode, and press . 3. Press and buttons until the target audio mode (Standard, Music, Film, Sport and User) is highlighted by cursor and setting of audio mode is completed. 4. Press button to close OSD.
Setting color temperature Color temperature of OSD may be changed. Perform the following steps to change the color temperature: 1. Press the Screen Display Control Key on remote controller and enter OSD menu. 2. Move the cursor to highlight the color temperature, and press . 3. Press and buttons until the target color temperature is highlighted by cursor and setting of color temperature is completed. 4. Press button to close OSD.
Setting zoom mode Zoom mode of OSD may be changed. Perform the following steps to change the zoom mode: 1. Press the Screen Display Control Key on remote controller and enter OSD menu. 2. Move the cursor to highlight the zoom mode, and press . 3. Press and buttons until the target zoom mode is highlighted by cursor and setting of zoom mode is completed. 4. Press button to close OSD.
Setting projection method Projection method of OSD may be changed. Perform the following steps to change the projection method: 1. Press the Screen Display Control Key on remote controller and enter OSD menu. 2. Move the cursor to highlight the projection method, and press . 3. Repeatedly press button to select target projection method (3, 0, 1 and 2), and setting of projection method is completed. 4. Press button to close OSD.
Setting electronic trapezoid correction Electronic trapezoid correction of OSD may be changed. Perform the following steps to change the electronic trapezoid correction: 1. Press the Screen Display Control Key on remote controller and enter OSD menu. 2. Move the cursor to highlight the electronic trapezoid correction, and press . 3. Press , , and buttons until the target electronic trapezoid correction is highlighted by cursor and setting of electronic trapezoid correction is completed. 4.
Setting software update (USB) Please contact with your local supplier of projectors.
Setting of reset all OSD may all be reset. Perform the following steps to reset all: 1. Press the Screen Display Control Key on remote controller and enter OSD menu. 2. Move the cursor to highlight the reset all, and press 4. Press . button to select Yes, all settings will be reset automatically, after then the QUMI user interface will be automatically switched back. Press the OSD screen control menu will be automatically switched back.
View status View status via OSD. Perform the following steps to view status: 1. Press the Screen Display Control Key on remote controller and enter OSD menu. 2. Move the cursor to highlight the status, and press 37 .
Chapter 5 Qumi Maintenance Qumi Cleaning Clean Qumi to remove dust and dirt for its normal operation. Warning: 1. Before cleaning, close Qumi and disconnect the power lines. Otherwise injury or system damage may be caused. 2. During cleaning, only wet cloth may be used. Exposure to water is not allowed for vents of Qumi. 3. If internal part of Qumi is exposed to a little water during cleaning, then Qumi cannot be used unless it is ventilated for several hours with its power lines disconnected. 4.
Troubleshooting FAQs and solutions In case of any problem arising from application of Qumi, all these methods may provide you with skills for problem solving. If such problem cannot be solved, please contact your distributor for help. Some problems may just be caused by improper connection of cables. Please check for possible conditions as below before seeking particular solutions. y Use other electrical equipment to check whether the power of outlet is normally supplied.
Image problem Problem: No image displayed in the screen 1. Check whether PC is properly configured. 2. Close all devices and then power them on again in proper sequence. Problem: Blurring image 1. Operate by remote controller. 2. Ensure that the distance between Qumi and screen is within specified limit. 3. If lens of Qumi are polluted, clean them by a cleaning cloth for optical lenses. Problem: Wider up or low end of image (trapezoid effect) 1.
Audio problem Problem: No sound 1. Adjust the volume of audio source. 2. Check the connection of audio cable. 3. Use other loudspeaker to test output of audio source. 4. Send Qumi for maintenance. Problem: Sound distortion 1. Check the connection of audio cable. 2. Use other loudspeaker to test output of audio source. 3. Send Qumi for maintenance. FAQs and solutions 1. Can Qumi be connected to the game console such as Microsoft Xbox or Sony PS3? Yes.
Specification Model Resolution Projection distance Size of projection screen (diagonal) Projection lens Throw ratio Vertical trapezoid correction Projection method Data compatibility SDTV/EDTV/HDTV Video compatibility Safety certificate Operating temperature Dimensions (WXHXD) AC input Power consumption Audio loudspeaker Input terminal Output terminal Qumi Q3PLUS Series HD (720p-1280x720) 0.7m~3.7m (19"-100") 762mm~2, 286mm (30”~90”) Electronic zoom in/out 1.
4. How to display images from digital camera or USB storage device? Connect such device to Qumi to display corresponding images or other contents by: y USB drive, hard disk and card reader y Digital camera y Smartphone y Multimedia storage browser When connected to such device, Qumi media center can be used to display images. 5.
Projection distance and size Projection distance and size specification Image diagonal (cm/inch) 76.2/30 101.6/40 114.3/45 127/50 152.4/60 177.8/70 203.2/80 228.6/90 Image width (cm/inch) Image width (cm/inch) 66.4/26.14 88.6/34.88 99.6/39.21 110.7/43.58 132.8/52.28 155/61.02 177.1/69.72 199.2/78.43 37.4/14.72 49.8/19.61 56/22.05 62.3/24.53 74.7/29.41 87.2/34.33 99.6/39.21 112.1/4.13 Projection distance (cm/inch) 112.5/44.29 150.3/59.17 169.1/66.57 188/74.02 225.8/88.9 263.6/103.78 301.2/118.58 339.
List of compatible signal Signal Resolution Horizontal synchronization (KHZ) Vertical synchronization (HZ) DVI/HDMI 720x400 37.9 85.0 O 640x480 31.5 60.0 O 640x480 37.9 72.0 O 640x480 37.5 75.0 O 640x480 43.3 85.0 O 800x600 35.2 56.0 O 800x600 37.9 60.0 O 800x600 48.1 72.0 O 800x600 46.9 75.0 O 800x600 53.7 85.0 O 800x600(for 3D) 76.3 120.0 O 1024x768 48.4 60.0 O 1024x768 56.5 70.0 O 1024x768 60.0 75.0 O 1024x768 68.7 85.
Qumi size 46
Regulatory compliance FCC warning As confirmed by tests, the Device conforms to Section 15 of FCC Rules in respect of limitations on Grade B digital equipment. Such limitations aim to provide the Device with proper protection against harmful interference in commercial environment. The Device may produce, use and radiate radio frequency energy; if the Device is not installed and used in accordance with instructions, harmful interference may be caused to radio communication.
List of name and content of toxic and hazardous substances or elements in the Product In accordance with the “Measures for the Control of Pollution from Electronic Information Products” issued by the Chinese government, in order to control and reduce pollution on environment caused by wasted electronic information products; promote production and sales of low-pollution electronic information products; and protect environment and human health, the toxic and hazardous substances that may be contained in the P
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
