Datasheet

ManualsBrandsDELTA ELECTRONICS ManualsPSU ComponentsDC/DC converter (SMD) 0.75 Vdc, 5 Vdc 10 A 50 W No. of outputs: 1 x

1

2

3

4

5

6

7

8

9

DATASHEET

DS_DNM10SMD10_07182012

FEATURES

 High efficiency: 93% @ 12Vin, 3.3V/10A out

 Small size and low profile: (SMD)

33.0x 13.5x8.8mm (1.30” x 0.53” x 0.35”)

 Standard footprint

 Voltage and resistor-based trim

 Pre-bias startup

 Output voltage tracking

 No minimum load required

 Output voltage programmable from

0.75Vdc to 5Vdc via external resistor

 Fixed frequency operation (300KHz)

 Input UVLO, output OTP, OCP

 Remote ON/OFF

 Remote sense

 ISO 9001, TL 9000, ISO 14001, QS 9000,

OHSAS 18001 certified manufacturing facility

 UL/cUL 60950-1 (US & Canada) recognized,

and TUV (EN60950-1) certified

 CE mark meets 73/23/EEC and 93/68/EEC

directive

APPLICATIONS

 Telecom / DataCom

 Distributed power architectures

 Servers and workstations

 LAN / WAN applications

 Data processing applications

OPTIONS

 Negative On/Off logic

 Tracking feature

 SMD package

Delphi DNM series Non-Isolated Point of Load

DC/DC Power Modules: 8.3-14Vin, 0.75-5.0V/10A out

The Delphi series DNM, 8.3~14V input, single output, non-isolated point

of load DC/DC converters are the latest offering from a world leader in

power systems technology and manufacturing ― Delta Electronics, Inc.

The DNM series provides a programmable output voltage from 0.75V to

5.0V through an external trimming resistor. The DNM converters have

flexible and programmable tracking and sequencing features to enable

a variety of sequencing and tracking between several point of load

power modules. This product family is available in a surface mount or

SIP package and provides 10A of output current in an industry standard

footprint and pinout. With creative design technology and optimization

of component placement, these converters possess outstanding

electrical and thermal performance and extremely high reliability under

highly stressful operating conditions.

FEATURES

 High efficiency: 93% @ 12Vin, 3.3V/10A out

 Small size and low profile: (SMD)

33.0x 13.5x 9.7mm (1.30” x 0.53” x 0.38”)

 Surface mount packaging

 Standard footprint

 Voltage and resistor-based trim

 Pre-bias startup

 Output voltage tracking

 No minimum load required

 Output voltage programmable from

0.75Vdc to 5Vdc via external resistor

 Fixed frequency operation (300KHz)

 Input UVLO, output OTP, OCP

 Remote ON/OFF

 Remote sense

 ISO 9001, TL 9000, ISO 14001, QS 9000,

OHSAS 18001 certified manufacturing facility

 UL/cUL 60950 (US & Canada), and TUV

(EN60950) – pending

 CE mark meets 73/23/EEC and 93/68/EEC-

pending

APPLICATIONS

 Telecom/DataCom

 Distributed power architectures

 Servers and workstations

 LAN/WAN applications

 Data processing applications

OPTIONS

 Negative On/Off logic

 Tracking feature

 Single-In-Line (SIP) package

Delphi DNM series Non-Isolated Point of Load

DC/DC Power Modules: 8.3-14Vin, 0.75-5.0V/10A out

The Delphi series DNM, 8.3~14V input, single output, non-isolated point

of load DC/DC converters are the latest offering from a world leader in

power systems technology and manufacturing ― Delta Electronics, Inc.

The DNM series provides a programmable output voltage from 0.75V to

5.0V through an external trimming resistor. The DNM converters have

flexible and programmable tracking and sequencing features to enable

a variety of sequencing and tracking between several point of load

power modules. This product family is available in a surface mount or

SIP package and provides 10A of output current in an industry standard

footprint and pinout. With creative design technology and optimization

of component placement, these converters possess outstanding

electrical and thermal performance and extremely high reliability under

highly stressful operating conditions.

Summary of content (15 pages)

PAGE 1
FEATURES  High efficiency: 93% @ 12Vin, 3.3V/10A out  Small size and low profile: (SMD) 33.0x 13.5x8.8mm (1.30” x 0.53” x 0.35”)  Standard footprint  Voltage and resistor-based trim  Pre-bias startup  Output voltage tracking  No minimum load required  Output voltage programmable from 0.
PAGE 2
TECHNICAL SPECIFICATIONS TA = 25°C, airflow rate = 300 LFM, Vin = 8.3Vdc and 14Vdc, nominal Vout unless otherwise noted. PARAMETER NOTES and CONDITIONS DNM10S0A0S10NFD Min.
PAGE 3
85 EFFICIENCY(%) EFFICIENCY(%) ELECTRICAL CHARACTERISTICS CURVES 75 65 Vin=8.3V 55 Vn=12V Vin=14V 45 1 2 3 4 5 6 7 8 9 90 85 80 75 70 65 60 Vin=8.3V Vin=12V Vin=14V 1 10 2 3 4 7 8 Figure 1: Converter efficiency vs. output current (0.75V output voltage) Figure 2: Converter efficiency vs. output current (1.2V output voltage) 95 95 90 90 EFFICIENCY(%) EFFICIENCY(%) 6 85 80 Vin=8.3V 75 Vin=12V 70 Vin=14V 65 1 2 3 4 5 6 7 8 80 Vin=8.
PAGE 4
ELECTRICAL CHARACTERISTICS CURVES EFFICIENCY(%) 100 95 90 Vin=8.3V 85 Vin=12V 80 Vin=13.2V 75 1 2 3 4 5 6 7 8 9 10 LOAD (A) Figure 7: Converter efficiency vs. output current (5.0V output voltage) Figure 8: Output ripple & noise at 12Vin, 2.5V/10A out Figure 9: Output ripple & noise at 12Vin, 5.0V/10A out Vo Vin Remote On/Off Vo Figure 10: Turn on delay time at 12vin, 5.0V/10A out Figure 11: Turn on delay time at Remote On/Off, 5.
PAGE 5
ELECTRICAL CHARACTERISTICS CURVES Remote On/Off Vo Figure 12: Turn on Using Remote On/Off with external capacitors (Co= 5000 µF), 5.0V/10A out Figure 13: Typical transient response to step load change at 2.5A/μS from 100% to 50% of Io, max at 12Vin, 5.0V out (Cout = 1uF ceramic, 10μF tantalum) Figure 14: Typical transient response to step load change at 2.5A/μS from 50% to 100% of Io, max at 12Vin, 5.0V out (Cout = 1uF ceramic, 10μF tantalum) Figure 15: Output short circuit current 12Vin, 0.
PAGE 6
TEST CONFIGURATIONS DESIGN CONSIDERATIONS Input Source Impedance TO OSCILLOSCOPE L VI(+) 2 100uF Tantalum BATTERY VI(-) Note: Input reflected-ripple current is measured with a simulated source inductance. Current is measured at the input of the module. Figure 17: Input reflected-ripple test setup To maintain low-noise and ripple at the input voltage, it is critical to use low ESR capacitors at the input to the module.
PAGE 7
DESIGN CONSIDERATIONS (CON.) FEATURES DESCRIPTIONS The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the module. An input capacitance must be placed close to the modules input pins to filter ripple current and ensure module stability in the presence of inductive traces that supply the input voltage to the module.
PAGE 8
FEATURES DESCRIPTIONS (CON.) Over-Temperature Protection The over-temperature protection consists of circuitry that provides protection from thermal damage. If the temperature exceeds the over-temperature threshold the module will shut down. The module will try to restart after shutdown. If the over-temperature condition still exists during restart, the module will shut down again.
PAGE 9
FEATURE DESCRIPTIONS (CON.) Table 1 provides Rtrim values required for some common output voltages, while Table 2 provides values of external voltage source, Vtrim, for the same common output voltages. By using a 1% tolerance trim resistor, set point tolerance of ±2% can be achieved as specified in the electrical specification. Table 1 VO (V) 0.7525 1.2 1.5 1.8 2.5 3.3 5.0 Rtrim (KΩ) Open 22.464 13.047 9.024 5.009 3.122 1.472 Table 2 VO (V) 0.7525 1.2 1.5 1.8 2.5 3.3 5.0 Vtrim (V) Open 0.670 0.650 0.
PAGE 10
FEATURE DESCRIPTIONS (CON.) The output voltage tracking feature (Figure 27 to Figure 29) is achieved according to the different external connections. If the tracking feature is not used, the TRACK pin of the module can be left unconnected or tied to Vin. Sequential Start-up Sequential start-up (Figure 27) is implemented by placing an On/Off control circuit between VoPS1 and the On/Off pin of PS2.
PAGE 11
FEATURE DESCRIPTIONS (CON.) Ratio-Metric Ratio–metric (Figure 29) is implemented by placing the voltage divider on the TRACK pin that comprises R1 and R2, to create a proportional voltage with VoPS1 to the Track pin of PS2. For Ratio-Metric applications that need the outputs of PS1 and PS2 reach the regulation set point at the same time The following equation can be used to calculate the value of R1 and R2. The suggested value of R2 is 10kΩ.
PAGE 12
THERMAL CURVES 12 DNM10S0A0S10(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin = 10V, Vo = 0.75V (Either Orientation) Output Current(A) 10 8 6 Natural Convection 4 2 0 60 Figure 31: Temperature measurement location The allowed maximum hot spot temperature is defined at 125℃ 12 DNM10S0A0S10(Standard) Output Current vs. Ambient Temperature and Air Velocity Output Current(A) @ Vin = 10V, Vo = 5.
PAGE 13
PICK AND PLACE LOCATION SURFACE-MOUNT TAPE & REEL LEADED (Sn/Pb) PROCESS RECOMMEND TEMP. PROFILE Note: All temperature refers to assembly application board, measured on the land of assembly application board. LEAD FREE (SAC) PROCESS RECOMMEND TEMP. PROFILE Temp. Peak Temp. 240 ~ 245 ℃ 220℃ Ramp down max. 4℃ /sec. 200℃ 150℃ Preheat time 90~120 sec. Time Limited 75 sec. above 220℃ Ramp up max. 3℃ /sec.
PAGE 14
MECHANICAL DRAWING SMD PACKAGE SIP PACKAGE (OPTIONAL) DS_DNM10SMD10_07182012 14
PAGE 15
PART NUMBERING SYSTEM DNM 10 S 0A0 S 10 N Product Series Input Voltage Numbers of Outputs Output Voltage Package Type Output Current On/Off logic S - Single 0A0 Programmable R - SIP S - SMD 0 -10A DNL - 16A DNM - 10A DNS - 6A 04 - 2.4~5.5V 10 - 8.