Datasheet

ManualsBrandsDELTA ELECTRONICS ManualsPSU ComponentsDC/DC converter (print) 0.75 Vdc, 3.3 Vdc 10 A 33 W No. of outputs: 1 x

DATASHEET

DS_DNM04SIP10_07182012D

FEATURES

 High efficiency: 96% @ 5.0Vin, 3.3V/10A out

 Small size and low profile: (SIP)

50.8x 13.4x 8.5 mm (2.00” x 0.53” x 0.33”)

 Signle-in-line (SIP) packaging

 Standard footprint

 Voltage and resistor-based trim

 Pre-bias startup

 Output voltage tracking

 No minimum load required

 Output voltage programmable from

0.75Vdc to 3.63Vdc via external resistor

 Fixed frequency operation

 Input UVLO, output OTP, OCP

 Remote ON/OFF

 Remote sense

 ISO 9001, TL 9000, ISO 14001, QS9000,

OHSAS18001 certified manufacturing facility

 UL/cUL 60950 (US & Canada) Recognized,

and TUV (EN60950) Certified

 CE mark meets 73/23/EEC and 93/68/EEC

directives



APPLICATIONS

 Telecom / DataCom

 Distributed power architectures

 Servers and workstations

 LAN / WAN applications

 Data processing applications

OPTIONS

 Negative On/Off logic

 Tracking feature

 SIP package

Delphi DNM, Non-Isolated Point of Load

DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.63V/10A out

The Delphi Series DNM04, 2.8-5.5V input, single output, non-isolated Point

of Load DC/DC converters are the latest offering from a world leader in

power system and technology and manufacturing -- Delta Electronics, Inc.

The DNM04 series provides a programmable output voltage from 0.75V to

3.63V using an external resistor. The DNM series has flexible and

programmable tracking and sequencing features to enable a variety of

startup voltages as well as sequencing and tracking between power

modules. This product family is available in a surface mount or SIP

package and provides up to 10A of current in an industry standard footprint.

With creative design technology and optimization of component placement,

these converters possess outstanding electrical and thermal performance

and extremely high reliability under highly stressful operating conditions.

Summary of content (16 pages)

PAGE 1
FEATURES  High efficiency: 96% @ 5.0Vin, 3.3V/10A out  Small size and low profile: (SIP) 50.8x 13.4x 8.5 mm (2.00” x 0.53” x 0.33”)  Signle-in-line (SIP) packaging  Standard footprint  Voltage and resistor-based trim  Pre-bias startup  Output voltage tracking  No minimum load required  Output voltage programmable from 0.75Vdc to 3.
PAGE 2
TECHNICAL SPECIFICATIONS (TA = 25°C, airflow rate = 300 LFM, Vin = 2.8Vdc and 5.5Vdc, nominal Vout unless otherwise noted.) PARAMETER NOTES and CONDITIONS DNM04S0A0R10 Min.
PAGE 3
100 100 95 95 90 EFFICIENCY(%) EFFICIENCY(%) ELECTRICAL CHARACTERISTICS CURVES Vin=4.5V 85 Vin=5.0V Vin=5.5V 80 90 Vin=3.0V 85 Vin=5.0V 80 75 Vin=5.5V 75 1 2 3 4 5 6 7 8 9 10 1 2 3 OUTPUR CURRENT(A) 6 7 8 9 10 Figure 2: Converter efficiency vs. output current (2.5V out) 95 100 90 90 EFFICIENCY(%) 95 EFFICIENCY(%) 5 OUTPUR CURRENT(A) Figure 1: Converter efficiency vs. output current (3.3V out) Vin=2.8V 85 Vin=5.0V Vin=5.5V 80 85 80 Vin=2.8V 75 Vin=5.
PAGE 4
ELECTRICAL CHARACTERISTICS CURVES Figure 7: Output ripple & noise at 3.3Vin, 2.5V/10A out Figure 8: Output ripple & noise at 3.3Vin, 1.8V/10A out Figure 9: Output ripple & noise at 5Vin, 3.3V/10A out Figure 10: Output ripple & noise at 5Vin, 1.8V/10A out Figure 11: Turn on delay time at 3.3Vin, 2.5V/10A out Figure 12: Turn on delay time at 3.3Vin, 1.
PAGE 5
ELECTRICAL CHARACTERISTICS CURVES Figure 13: Turn on delay time at 5Vin, 3.3V/10A out Figure 14: Turn on delay time at 5Vin, 1.8V/10A out Figure 15: Turn on delay time at remote turn on 5Vin, 3.3V/16A out Figure 16: Turn on delay time at remote turn on 3.3Vin, 2.5V/16A out Figure 17: Turn on delay time at remote turn on with external Figure 18: Turn on delay time at remote turn on with external capacitors (Co= 5000 µF) 5Vin, 3.3V/16A out capacitors (Co= 5000 µF) 3.3Vin, 2.
PAGE 6
ELECTRICAL CHARACTERISTICS CURVES Figure 19: Typical transient response to step load change at 2.5A/μS from 100% to 50% of Io, max at 5Vin, 3.3Vout (Cout = 1uF ceramic, 10μF tantalum) Figure 20: Typical transient response to step load change at 2.5A/μS from 50% to 100% of Io, max at 5Vin, 3.3Vout (Cout =1uF ceramic, 10μF tantalum) Figure 21: Typical transient response to step load change at 2.5A/μS from 100% to 50% of Io, max at 5Vin, 1.
PAGE 7
ELECTRICAL CHARACTERISTICS CURVES Figure 23: Typical transient response to step load change at 2.5A/μS from 100% to 50% of Io, max at 3.3Vin, 2.5Vout (Cout =1uF ceramic, 10μF tantalum) Figure 24: Typical transient response to step load change at 2.5A/μS from 50% to 100% of Io, max at 3.3Vin, 2.5Vout (Cout =1uF ceramic, 10μF tantalum) Figure 25: Typical transient response to step load change at 2.5A/μS from 100% to 50% of Io, max at 3.3Vin, 1.
PAGE 8
TEST CONFIGURATIONS DESIGN CONSIDERATIONS Input Source Impedance L VI(+) 2 100uF Tantalum BATTERY VI(-) Note: Input reflected-ripple current is measured with a simulated source inductance. Current is measured at the input of the module. Figure 29: Input reflected-ripple test setup To maintain low noise and ripple at the input voltage, it is critical to use low ESR capacitors at the input to the module.
PAGE 9
DESIGN CONSIDERATIONS (CON.) FEATURES DESCRIPTIONS The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the module. An input capacitance must be placed close to the modules input pins to filter ripple current and ensure module stability in the presence of inductive traces that supply the input voltage to the module.
PAGE 10
FEATURES DESCRIPTIONS (CON.) Vtrim  0.7  0.1698  Vo  0.7525 Over-Temperature Protection For example, to program the output voltage of a DNL module to 3.3 Vdc, Vtrim is calculated as follows The over-temperature protection consists of circuitry that provides protection from thermal damage. If the temperature exceeds the over-temperature threshold the module will shut down. The module will try to restart after shutdown.
PAGE 11
FEATURE DESCRIPTIONS (CON.) The amount of power delivered by the module is the voltage at the output terminals multiplied by the output current. When using the trim feature, the output voltage of the module can be increased, which at the same output current would increase the power output of the module. Care should be taken to ensure that the maximum output power of the module must not exceed the maximum rated power (Vo.set x Io.max ≤ P max).
PAGE 12
FEATURE DESCRIPTIONS (CON.) Sequential Start-up Ratio-Metric Sequential start-up (Figure 40) is implemented by placing an On/Off control circuit between VoPS1 and the On/Off pin of PS2. Ratio–metric (Figure 42) is implemented by placing the voltage divider on the TRACK pin that comprises R1 and R2, to create a proportional voltage with VoPS1 to the Track pin of PS2. For Ratio-Metric applications that need the outputs of PS1 and PS2 reach the regulation set point at the same time.
PAGE 13
THERMAL CONSIDERATIONS Thermal management is an important part of the system design. To ensure proper, reliable operation, sufficient cooling of the power module is needed over the entire temperature range of the module. Convection cooling is usually the dominant mode of heat transfer. Hence, the choice of equipment to characterize the thermal performance of the power module is a wind tunnel.
PAGE 14
THERMAL CURVES 12 DNM04S0A0R10(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin = 3.3V, Vo = 2.5V (Either Orientation) Output Current(A) 10 Natural Convection 8 6 4 2 0 60 Figure 44: Temperature measurement location * The allowed maximum hot spot temperature is defined at 125℃ 12 DNM04S0A0R10(Standard) Output Current vs. Ambient Temperature and Air Velocity @ Vin = 5V, Vo = 3.
PAGE 15
MECHANICAL DRAWING SMD PACKAGE (OPTIONAL) SIP PACKAGE DS_DNM04SIP10_07182012D 15
PAGE 16
PART NUMBERING SYSTEM DNM Product Series DNL - 16A DNM - 10A DNS - 6A 04 S 0A0 R 10 P Output Voltage Package Type Output Current On/Off logic 0A0 Programmable R - SIP S - SMD 10 - 10A Numbers of Input Voltage Outputs 04 - 2.8~5.5V 10 - 8.3~14V S - Single F N- negative P- positive D Option Code F- RoHS 6/6 D - Standard Function (Lead Free) MODEL LIST Model Name Packaging Input Voltage Output Voltage Output Current Efficiency 5.0Vin, 100% load DNM04S0A0R10PFD SIP 2.8 ~ 5.5Vdc 0.