VENTILATION FAN WITH LIGHT AND HEATER MODEL RAD80L TABLE OF CONTENTS Package Contents 2 Important Instructions 3 Preparation 4 Assembly Instructions 6 Wiring Instructions 10 Operating Instructions 10 Care and Maintenance 11 Troubleshooting 13 Dimensions 14 14 Warranty READ AND SAVE THESE INSTRUCTIONS Please read and understand this entire manual before attempting to assemble, operate, or install the product.
PACKAGE CONTENTS 1 PART DESCRIPTION QTY 1 Fan Body 1 2 Grille Assembly 1 3 Light Lens 1 4 Suspension Bracket I 2 5 Suspension Bracket II 2 2 HARDWARE CONTENTS A 3 Short Machine Screw (M4x12) Qty.4 B Machine Screw (M5x14) Qty.1 4 C Wood Screw( 5 Model: RAD80L 2 4x14) Qty.
IMPORTANT INSTRUCTIONS When using electrical appliances, basic precautions should and injury to persons, including the following: •Read all instructions before installing or using this heater. Extreme caution is necessary when heater fan is used • by or near unattended children, and / or persons with disabilities or limitations. Do not operate heater if it malfunctions. Disconnect power • at service panel and have heater inspected by reputable electrician before reusing. Do not use outdoors.
PREPARATION Tools Required for Assembly (not included): Hammer, Flathead Screwdriver, Wire Nuts, Nails, Duct Tape, Phillips Head Screwdriver, Utility Knife Helpful Tools (not included): Electric Drill, Drill Bits WARNING: Turn off electricity at breaker box before beginning installation. Before installation, provide inspection and future maintenance access at a location that will not interfere with installation work.
ASSEMBLY INSTRUCTIONS Unpacking Carefully remove unit from carton. Remove the foam in the housing. Refer to the Package Contents list on page 2 to verify that all parts are present. Installing the unit Installing the fan body in an existing building requires an accessible area (attic or crawl space) above the planned installation location and existing duct and wiring. CAUTION: Check area above installation location to ensure that: • Wiring can be run to the planned location.
ASSEMBLY INSTRUCTIONS 1-1 1. Mounting the fan between the joists a. Insert either the 12 in. suspension brackets 5 or 14 in. suspension brackets 4 to the duct side and back of the fan body 1 , depending on the distance between the joists. 1 b. Insert the fan body 1 between joists. Make sure the fan body is level and perpendicular with the c. Allow for thickness of the ceiling board used in your application. Fan body 1 with ceiling board. 5 4 d.
ASSEMBLY INSTRUCTIONS 2. Connecting the duct 2-1 CAUTION: All ducting must comply with local and national building codes. a. Insert the duct into the duct connector and tape all duct work connections to make them secure and air tight. 2-2 b. as shown in Figure 2-2. Install the duct with a gradient of 1°-2° to the outside. Turning angle too large Duct shrink Too many elbows Elbow near the body Body 3-1 3. Remove the fan junction box cover a .
ASSEMBLY INSTRUCTIONS 4. Completing the Installation 4-1 Vent a. Check the plug from the fan into the receptacle marked “Vent” Light Heat Check the plug from the heating unit into the receptacle marked “Heat” 4-2 b. Plug the Light Connector into the receptacle marked “Light” c. Install the Grille Assembly 2 into the Fan Body 1 using the Machine Screw B . 4-3 2 CAUTION: Do not use Wood Screw C in place of Machine Screw B .
ASSEMBLY INSTRUCTIONS d. Install the Light Lens 3 into Grille Assembly 2 .
WIRING INSTRUCTIONS CAUTION: • Make sure power is switched off at service panel before starting installation. LIGHT SWITCH AWG18 • All electrical connections must be made in accordance with local codes, ordinances, or national electrical code. If you are unfamiliar with methods of installing electrical wiring, HEATER SWITCH AWG14 BLU RED VENT. SWITCH BLK AWG18 BLK WARNING: LINE IN • This unit must be wired on a separate 15 amp circuit.
CARE AND MAINTENANCE 1 Routine maintenance must be done every year. 2 CAUTION: • Make sure power is switched off at service panel before servicing the unit. To replace lamp • Use bulb reted up to 60 watts only. 3 • Allow lamp to cool before replacing. To clean fan, disassemble using the following steps: 1. Remove Light Lens 3 cover and Lamp. 2. Remove Machine Screw B 2 . 2 Hardware B Machine Screw (M5x12) Qty.
CARE AND MAINTENANCE 4. Remove Grille Assembly 2 4 . 1 2 5 5. Remove dust and dirt from the Fan Body 1 with a vacuum cleaner. Do not use abrasive cloths, steel wool pads, or scouring powders. Never use solvents, thinner or harsh chemicals when cleaning the fan. 1 Vacuum cleaner 6 6. Replace Grille Assembly 2 back onto Fan Body 3 . Please refer to Completing the Installation. Follow the steps on pages 8-9 to assemble fan back together.
TROUBLESHOOTING PROBLEM The fan is not turning on The fan seems louder than it should POSSIBLE CAUSE CORRECTIVE ACTION 1. Power off 1. Make sure power supply is on. 2. Faulty switch 2. Test or replace switch. 3. Faulty wire connection 3. Check wire in switch box. 1. CFM 1. Be sure the CFM rating on the fan matches the size of your room. 2. Damper not working properly or damaged 2. Check damper to ensure it is opening and closing properly.
ø4.0 DIMENSIONS Unit: inch 14 PRODUCT SPECIFICATIONS SPECIFICATIONS Model No. RAD80L 80 CFM Noise 1.5 Sones Voltage 120V Hertz 60Hz Power Consumption 1400W Duct Diameter 4 in. Weight 12.1 lbs. TYPE IC INHERENTLY PROTECTED. THERMALLY PROTECTED L.
WARRANTY DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY Delta Electronics Inc. (“Delta Electronics”) warrants to the original consumer purchaser in the USA that the Breez ventilation fan products will be free from defects in material or workmanship. This warranty is limited to three (3) years from the original date of purchase. Limitations and Exclusions 1. During the warranty period, a replacement for any defective product will be supplied free of charge for installation by the consumer.
Model: RAD80L 16
