VENTILATION FAN / LED LIGHT MODEL ITG50LED/ITG80LED TABLE OF CONTENTS Package Contents 2 General Safety Information 3 Preparation 4 Assembly Instructions 5 New Construction 5 Existing Construction 6 Grille Installation 8 Operation 8 Care and Maintenance 9 Troubleshooting 10 Dimensions 11 11 Warranty READ AND SAVE THESE INSTRUCTIONS Address: 46101 Fremont Boulevard, Fremont, CA 94538 US Toll Free Number: 1-888-979-9889 www.deltabreez.
PACKAGE CONTENTS 1 2 3 2 PART DESCRIPTION QTY ❶ Fan Body 1 ❷ Grille 1 ❸ Duct Connector 1
GENERAL SAFETY INFORMATION 7. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit lnterrupter) – protected branch circuit. READ AND SAVE THESE INSTRUCTIONS GENERAL SAFETY INFORMATION 1. Make sure that the electric service supply voltage is AC 120V, 60Hz. 8. Do not use this unit with any other solid-state control device.
PREPARATION Tools Required for Assembly (not included): Hammer, Flathead Screwdriver, Wire Nuts, Nails, Duct Tape, Phillips Head Screwdriver, Utility Knife Roof cap (with built-in damper) Short piece of flexible duct helps alignment and absorbs sound Helpful Tools (not included): Electric Drill, Drill Bits Fan housing WARNING: Turn off electricity at breaker box before beginning installation. or Carefully remove unit from carton.
ASSEMBLY INSTRUCTIONS NEW CONSTRUCTION 1 Turn off power source. Review all safety precautions. 1. Attach the Duct Connector ❸ to the Fan Body ❶ 3 1 2 2. Remove the wiring box cover from the Fan Body ❶ . Remove the wiring knockout from the wiring box 1 1 1 1 3 3. Place the Fan Body ❶ next to a ceiling joist or wall stud. The fan body should be level and perpendicular to the joist or stud. 1 1 1 1 Joist or wall stud JoistJoist or or wallwall stud stud 4 4.
ASSEMBLY INSTRUCTIONS 6. Install a circular 4 in. duct (not included) and secure it with duct tape or clamps (neither included). Finish ceiling work. The ceiling hole should be aligned with the edge of the Fan Body ❶ . 6 4 in. Duct Duct tape or clamp EXISTING CONSTRUCTION 1 Turn off power source. Review all safety precautions. 1. Remove existing fan. 2 2. Measure the opening to ensure it is large enough to accommodate the new Fan Body(7 1/2in. x 7 1/4in.). the joist. 3 3.
3 1 ASSEMBLY INSTRUCTIONS 5. Remove the wiring box cover from the Fan Body ❶ . Remove the wiring knockout from the wiring box 5 1 6 6. Remove the three screws that hold the fan motor assembly in place. Remove the fan motor assembly from the Fan Body ❶ . Unplug fan connector. 1 7 7. Pull the wire through the hole and into the junction box(not included), secure 120VAC house wiring from the wall diagram on page4. 14AWG is the smallest conductor that shall be used for branchcircuit wiring.
GRILLE INSTALLATION Insert the LED light connector into the fan body. Pinch the mounting springs on the Grille ❷ , and insert them into the narrow rectangular slots inside the fan. Push the Grille ❷ up toward the ceiling. 2 installation. FAN / LED LIGHT OPERATION Operation Fan mode: Turn the Fan switch to operate ON/OFF of Fan function. Light mode: Turn the Light switch to operate ON/OFF of LED lighting function.
CARE AND MAINTENANCE See safety information before proceeding. Routine maintenance should be done at least once a year. • Never use solvents, thinner or harsh chemicals when cleaning the fan. • Do not allow water to enter the motor. 1 • Do not immerse metal parts in water. • Do not immerse resin parts in water over 140º Fahrenheit. • Do not immerse LED module in water. Turn off power source. Review all safety precautions. 1. To remove grille ❷ , squeeze springs and pull down. 2 2.
TROUBLESHOOTING PROBLEM The fan is not turning on The fan seems louder than it should POSSIBLE CAUSE CORRECTIVE ACTION 1. Power off 1. Make sure power supply is on. 2. Faulty switch 2. Test or replace switch. 3. Faulty wire connection 3. Check wire in switch box. 1. CFM too great 1. Be sure the CFM rating on the fan matches the size of your room. 2. Damper not working properly or damaged 2. Check damper to ensure it is opening and closing properly.
DIMENSIONS UNIT: INCH PRODUCT SPECIFICATIONS SPECIFICATIONS Model No. ITG50LED ITG80LED Voltage (V) 120 120 Frequency Air Flow Fan Power Max Current Weight (Amps) (lb.) (Hz) @0.1”(CFM) @0.1”SP(W) 60 60 50 80 5.0 11.3 11 0.22 0.28 Note LED light spec. 4.8 13.0 Watts, Single 850Lumens, Speed 2700K 4.8 13.
WARRANTY DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY Delta Electronics Inc. (“Delta Electronics”) warrants to the original consumer purchaser in the USA that the Breez ventilation fan products will be free from defects in material or workmanship. This warranty is limited to three (3) years from the original date of purchase. Limitations and Exclusions 1. During the warranty period, a replacement for any defective product will be supplied free of charge for installation by the consumer.
