Installation Guide

MODELS:
ITG50/VFB050B4A1
INSTALLATIONS
Proper insulation around the fan to minimize building
heat loss and gain. 4” circular duct is recommended
for installation. The ducting from this fan to the
outside of building has a strong effect on the air flow,
noise and energy use of the fan. Use the shortest,
straightest duct routing possible for best performance,
and avoid installing the fan with smaller ducts than
recommended. Insulation around the ducts can
reduce energy loss and inhibit mold growth. Fans
installed with existing ducts may not achieve their
rated air flow.
Install with wood frame
Model No. ITG50 / VFB050B4A1
Install Dim.
(Inch)
7.5X7.25
1. Remove motor plate from housing by
removing three screws. (Fig. C)
2. Remove wiring cover from housing by pulling
straight out. Choose a hole and use a slotted
screwdriver to remove it. (Fig. D)
3. Follow all local electrical and safety codes.
NEVER place a switch where it can be
reached from a tub or shower. Connect wires
as shown in wiring diagrams. (Fig. E)
4. Using wire nuts(not provided), connect house
power cable to ventilating fan wires. 14 AWG
(2.1 mm
2
) is the smallest conductor that shall
be used for branch-circuit wiring. (Fig. F)
5. Insert the duct into the duct connector and
tape all ductworks connection to make them
secure and airtight. Install the duct with a
gradient 1°~2° to the outside. (Fig. G)
6. New installation prior to finishing the
ceiling: Insert the fan between joists. Make
sure the fan body is level and perpendicular
with the joist. (Fig. H)
7. Replacement installation: After making
electrical and ductwork connections (see steps
2~5), nail housing in place. Drive nails through
the housing where indicated by arrows. (Fig. I)
8. New installation in an existing ceiling :
Bend tabs outward 90°(Use a screw driver if
desired) and position housing so that tabs rest
against bottom edge of joists (or front of stud).
Nail housing to joist or stud using four nails to
ensure a solid, quiet installation. Ceiling
installations: Tabs on opposite side of housing
can be bent outward to rest on top of 1/2"
ceiling material and provide extra stability. (Fig.
J)
9. Plug in the motor and locking the fan body
back by using three screws. (Fig. C)
10. Squeeze grille springs together and insert
springs into slots in motor plate. Push grille up
against ceiling. When the power on, check for
abnormal vibration or sound. Insert the
mounting springs into the slots and mount the
grille to the body. (Fig. K)
Fig. C Fig. C
Fig. D
Fig. E
Fig. F
Fig. G
Fig. H Fig. H
Fig. H Fig. I
Fig. J Fig. K
WARRANTY
DELTA ELECTRONICS THREE YEAR LIMITED
WARRANTY
Delta Electronics Inc.(“Delta Electronics”)
warrants to the original consumer purchaser in the
USA that the Breez ventilation fan products will be
free from defects in material or workmanship. This
warranty is limited to three (3) years from the original
date of purchase.
Limitations and Exclusions
1. During the warranty period, a replacement for
any defective product will be supplied free of
charge for installation by the consumer. The
warranty provided herein does not cover charges
for labor or other costs incurred in the
troubleshooting, repair, removal, and installation
service.
2. All returns of defective parts or products must
include the product model number, and must be
made through an authorized Delta Electronics
distributor. Authorized returns must be shipped
prepaid. Repaired or replacement products will
be shipped by Delta Electronics F.O.B. shipping
point.
3. Delta Electronics shall not be liable for any
indirect, incidental, consequential, punitive, or
special damages arising out of or in connection
with products use or performance, regardless of
the form of action whether in contract, tort
(including negligence), strict product liability or
otherwise.
4. This warranty does not extend to fluorescent
lamp starters and tubes.
5. The warranty does not cover if user does not
comply with manufacture’s installation manual.
6. To qualify for warranty service, you must notify
Delta Electronics at the address or telephone
number below.
7. Delta Electronics shall have no liability to the
original owner-user with respect to any defect
caused by abuse, misuse, neglect, improper
transportation or storage, improper testing,
improper installation, improper operation,
improper use, improper maintenance, improper
repair, improper alteration, improper modification,
tampering or accident of products or parts
thereof, or unusual deterioration or degradation of
products or parts thereof due to a physical
environment beyond the requirements of
products’ specifications.
Address: 46101 Fremont Boulevard, Fremont,
CA 94538
US Toll Free Number: 1-888-979-9889