VENTILATION FAN MODEL 80HLED/80L/80LED/100HLED/100LED TABLE OF CONTENTS 80L Package Contents 2 General Safety Information 3 Preparation 4 Assembly Instructions 5 New Construction 5 Existing Construction 6 Connect Wiring 7 Grille Installation 8 Operation 8 Care and Maintenance 9 Troubleshooting 10 Dimensions 11 Product Specifications 11 Warranty 12 80HLED/80LED/100HLED/100LED READ AND SAVE THESE INSTRUCTIONS US Toll Free Number: 1-888-979-9889 MFG Model : VFB80HLED2/VFB080C4L
PACKAGE CONTENTS For all Models Appearance Part name Duct Connector (4’’ ) 1 Tapping Screw (Ø4×25) 8 Machine Screw (#8-32x5/16’’) 4 Hanger Bar 4 For Model of 80L For Model of 80LED/100LED Part name Quantity Appearance Quantity Part name Grille 1 Grille 1 Fan Body 1 Fan Body 1 Housing 1 Housing 1 Machine Screw (#8- 32x1-1/4’’) 1 Machine Screw (M4x6) 1 Grille Bracket 1 GU24 Base Lamp (11W) 1 For Model of 80HLED/100HLED Part name Appearance Quantity Grille 1 Fan Body 1
GENERAL SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS 1. Make sure that the electric service supply voltage is AC 120V, 60Hz. 2. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupational Safety and Health Act (OSH Act). 7. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFCI (Ground Fault Circuit lnterrupter) – protected branch circuit. 3.
PREPARATION Tools Required for Assembly (not included): Hammer, Flathead Screwdriver, Wire Nuts, Nails, Duct Tape, Phillips Head Screwdriver, Utility Knife. Short piece of flexible duct helps alignment and absorbs sound Helpful Tools (not included): Electric Drill, Drill Bits. Fan housing WARNING: Turn off electricity at breaker box before beginning installation. or Carefully remove unit from carton.
ASSEMBLY INSTRUCTIONS NEW CONSTRUCTION BEFORE INSTALLATION Turn off power source. Review all safety precautions. 1 MOUNT HOUSING WITH FLANGE: Tab 1. To bend the housing tabs out to 90 degrees and make housing tabs contact the bottom of the joist. Joist 2 2. The housing mounts with 4 tapping screws (ø 4x25). Screw housing to joist through lowest holes in each mounting flange, then through the other holes. Joist Tapping Screw USING HANGER BARS 3 3. Insert hanger bars into the channels on housing.
ASSEMBLY INSTRUCTIONS (Continued) b EXISTING CONSTRUCTION–ACCESSIBLE FROM ABOVE a 1. Measure the existing ceiling opening or cut a new opening to ensure it is large enough to accommodate a the new fan (8 in. x 8.25 in. suggested). 1 2. Place housing in opening so that its bottom edge is flush with finished ceiling. Screw housing to joist through lowest holes in each mounting flange. 2 in". 9.4 8.25 n.4." 8 9i Joist Screw Ø4×25 3.
ASSEMBLY INSTRUCTIONS (Continued) 2 2. Unplug light and fan connectors from junction box. Remove fan body from housing. Machine Screws (M4 x 45) 3 3. Insert the duct (not provided) into the duct connector and tape all ductworks connection to make them secure and airtight by through the ceiling opening. Using wire nuts (not provided) connect house wires to fan wires as shown in the connect wiring diagram on page 8. 4 4.
ASSEMBLY INSTRUCTIONS (Continued) SWITCH BOX JUNCTION BOX BLACK OFF ON WHITE BLUE (80L) RED (80LED / 100LED) WHITE GREEN BLUE (80L) RED (80LED / 100LED) GROUND (bare) FAN SWITCH BLACK WHITE ON/OFF SWITCH (purchase separately) L SWITCH BOX N OFF ON LIGHT SWITCH L N WIRING PLATE FAN LIGHT SWITCH SWITCH GRD 120 VAC LINE IN 2 1 GRILLE INSTALLATION 1. For Model of 80L Insert the grille bracket into the fan body, and lock it with machine screw (M4×6).
CARE AND MAINTENANCE TURN OFF POWER SOURCE. REVIEW ALL SAFETY PRECAUTION. See safety information before proceeding. Routine maintenance should be done at least once a year. • Never use solvents, thinner or harsh chemicals when cleaning the fan. • Do not allow water to enter the motor. 1 • Do not immerse metal parts in water. • Do not immerse resin parts in water over 140º F. 1. To remove grille, unplug the light connector, squeeze springs and pull down.
TROUBLESHOOTING PROBLEM The fan is not turning on The fan seems louder than it should POSSIBLE CAUSE CORRECTIVE ACTION 1. Power off 1. Make sure power supply is on. 2. Faulty switch 2. Test or replace switch. 3. Faulty wire connection 3. Check wire in switch box. 1. CFM too great 1. Be sure the CFM rating on the fan matches the size of your room. 2. Damper not working properly or damaged 2. Check damper to ensure it is opening and closing properly.
DIMENSIONS 10 3 4 " 8" " 1 4 8 10 3 4 " 4" 80HLED/80LED/ 100HLED/100LED 11" 5 34" 11" 80L PRODUCT SPECIFICATIONS Voltage Frequency (V) (Hz) (CFM) (W) (Amps) (lb.) 80L / VFB080C4L2 120 60 80 11 0.50 6.4 Single Speed 80HLED / VFB80HLED2 120 60 80 11 0.33 6.1 Single Speed 80LED / VFB080C4LED2 120 60 80 11 0.33 6 Single Speed 13W LED, 850 Lumens, 2700K 100HLED / VFB100HLED2 120 60 100 13.6 0.35 6.
WARRANTY DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY Delta Electronics Inc. (“Delta Electronics”) warrants to the original consumer purchaser in the USA and Canada that the Breez ventilation fan products will be free from defects in material or workmanship. This warranty is limited to three (3) years from the original date of purchase. Limitations and Exclusions 1. During the warranty period, a replacement for any defective product will be supplied free of charge for installation by the consumer.
