I:>E:LPHI Delphi Audio System Installation ~ ~ .........
A CAUTION: TO REDUCE THE RISI Of ELECTRIC SHOCI. DO NOT REMOVE REAR COVER NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIfiED SERVICE PERSONNEL. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
What's in the Box - 4 Setting up the Delphi Audio System 4 Using SKYFilSKYFi2 with the Delphi Audio System 5 Using roadyXT with the Delphi Audio System 5 Using the Delphi Audio System with Batteries 6 Setting up the Antenna 6 Positioning the XM Antenna 6 Optimizing Antenna Position/Signal 6 Installing the XM Antenna on the Rear of the Delphi Audio System ? Indoor Installation on a Flat Surface ? Outdoor Installation or Indoor Wall Mounting ? Using the Delphi Audio System 8 Volume 8
What's in the Box Your Delphi Audio System Kit contains the following components: 12V DC adaptor Battery compartment and antenna cable storage 12V DC jack Set up your Delphi Audio System by following these steps: 1. Connect the supplied 12V DC power adaptor to the jack on the rear of the Delphi Audio System, and the other end to a wall outlet. 2. Connect the XM Antenna to the antenna jack located inside the battery compartment and antenna cable storage located on the bottom of the Delphi Audio System.
Using SK'Y'FilSK¥Fi2 wittl ttle Delptli Audio - S~stem~ ... " .,-~; 1. Insert the SKYFi/SKYFi2 Receiver (sold separately) into the cradle by first pressing in on the back of the black inset cradle in the Delphi Audio System. Then letting the cradle tilt forward, carefully slide the SKYFi/SKYFi2 Receiver down into the tray so that the alignment tabs on the sides of the tray line up with the slots on SKYFi/SKYFi2 and the connector is completely seated.
Using the Delphi Audio System with Batteries The Delphi Audio System can be used with batteries (not supplied) to allow you to listen to XM outdoors or in other locations without access to an AC power source. Alkaline or rechargeable NiCD batteries are recommended. Battery life will vary depending on how the system is operated and the type of batteries being used. It is recommended that the AC adaptor be the primary power source for the Delphi Audio System in order to preserve battery life. 1.
Installing the XM Antenna on the Rear of the Delphi Audio System When outdoors with a view of the southern sky, or in an area of repeater coverage, or when receiving a strong signal indoors, you can conveniently mount the antenna directly on the back of the Delphi Audio System. 1. Remove the battery compartment and antenna cable storage cover as described in "Setting up the Delphi Audio System," wind the antenna around the two cable hooks, leaving several inches of cable free, and replace the cover. 2.
2. Attach four screws to the wall using the screw-locator pattern shown here. Photocopy the pattern to use as a template. Use screws with head sizes small enough to fit in the center of each of the four holes but large enough not to pop out of the elongated sections. Leave 1/8" of the screw shanks behind the heads sticking out of the wall. T1.6in(40mm)~ E I---..-------E--,--------------------I -----y--C-~--L------------------l---.L---L~ N .
Note that the "Line Out Level" cannot be reset while the receiver is in the Delphi Audio System since the volume control should be used to control the audio output instead. If the line out setting is adjusted while in a car cradle or home stand and the receiver is later reconnected to the Delphi Audio System, it will automatically return to the prior setting the next time it is used in a vehicle adaptor or home adaptor.
2. On placement: • Do not place the Delphi Audio System on an inclined or unstable surface. • Do not place anything within 1/2" of the side of the cabinet. The audio/ventilation ports must be unobstructed for the Delphi Audio System to operate properly and prolong the life of its components. • Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the unit to prevent possible damage from the magnetic fields. 3.
Specifications ITEM 1 UNIT Continuous average SPECIFICATION NOMINAL LIMITED W >4 >3.5 % >0.6 >1.0 REMARK Rated output (10%) at 1 KHz power output 2 Total harmonic Output: 0.5 W Frequency: 70 Hz - Line input Frequency: 70 Hz - -3 dB odB: 0.
www.delphLcom and for all products for the remainder of the limited warranty period, you must contact Delphi by phone at 1.877.GO DELPHI [1.877.463.3574). Iffurther clarification or additional information is required from Delphi, you may call Delphi at 1.877.GO DELPHI (1.877.463.3574) . If warranty service is needed at any time during the warranty period, the purchaser will be required to furnish a sales receipt/proof of purchase indicating the date of purchase, amount paid. and place of purchase.
DE:LPHI user gUlde SA10175 9 o XM Satellite Radio Receiver ((.~o») A Important: This manual contains importllntsafetyand operating information. Please read.underst/llnd.llnd follow tl'lc! lnstructlol'\S In this manual. FailuRe ttl do so could I'QSUlt In pl!rSOI'IsllnJury,dClath,.ancl/ordamagCl tel your roadyXT. Iccessorles.andlor to your vehlde or property.
FCC ID: RS2SA10177 IC: 5697A-SA10177 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. The Delphi XM® roadyXT Satellite Radio Receiver incorporates an FM transmitter and is therefore classified as an intentional transmitter.
Table of Contents A Brief History · · · · · · · · · · · · · · · · · · · · · · · · · 4 About Delphi · · · · · · · · · · · · · · · · · · · · · · · · · 5 About XM · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 5 Let’s Get Started · · · · · · · · · · · · · · · · · · · · · · 6 First, some important reminders · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 6 Controls · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 7 Display · · · · · · · · · · · · · · · · · · · · · · · · · · · ·
A Brief History 4 A Brief History The new Delphi roadyXT Satellite Radio Receiver—smaller, lighter, and more versatile than the best-selling Roady2®. • Dock your roadyXT into cradles that are easily installed in your vehicles or your home. One simple motion connects your roadyXT’s power, audio, and antenna. • A built-in FM transmitter allows you to hear XM programming on any nearby FM radio, using any unused frequency on the FM band.
About Delphi Delphi is a worldwide leader in mobile electronics, vehicle components, and audio technology. Delphi created the first in-dash car radio in 1936 and continues its strong tradition of innovation in the audio industry. Now Delphi technology has helped make satellite radio a reality, and Delphi continues to expand its in-vehicle and consumer electronics technologies.
Let’s Get Started 6 Let’s Get Started First, some important reminders We know you’re eager to turn on your new roadyXT and listen to XM. Please take a moment to remember the following: Warning: This manual contains important safety and operating information. Please read, understand, and follow the instructions in this manual. Failure to do so could result in personal injury, death, and/or damage to your roadyXT, accessories, and/or to your vehicle or property.
Controls power menu – access advanced features and configuration options up and down arrows, select – change channels, choose menu options, TuneSelect™ disp – change what you see on the display pre/dir – select between direct channel entry or up to 30 presets search – look up channels by category or scan all channels memory – save and recall up to 20 artist names or song titles jump – return to previous channel; press and hold to select one of last six FM frequencies used for transmitter numbers – e
Let’s Get Started 8 Display signal strength – 1 to 3 bars search by scanning all channels display modes 1-5 search channels by category channel selection mode – direct entry or preset banks A, B, or C additional info – channel name, channel number, artist, song title, Stock Ticker, and Info Extras
Remote Control* power up and down arrows, select – change channels, choose menu options, TuneSelect™ search – look up channels by category or scan all channels pre/dir – select between direct channel entry or up to 30 presets menu – access advanced features and configuration options + and - – change channels, or control volume if roadyXT is placed in an audio system jump – return to previous channel; press and hold to select one of last six FM frequencies used for modulator numbers – enter a channel d
Activating Your roadyXT 10 Activating Your roadyXT Use the arrow buttons to find channel 0, then push the “select” button to choose it. You should see an 8-character XM Radio ID in the display. (The XM Radio ID should also be on the bottom of your roadyXT, and on the package.) Write the ID here: Note: Carefully check your XM Radio ID. The letters I, O, S, and F are not used. Activate your XM Satellite Radio service by contacting XM at http://activate.xmradio.com or by calling 1.800.XM.RADIO (1.800.967.
Listening to XM Selecting channels Select a channel directly by entering its channel number. Press the “pre/dir” button (step 1) until appears on the screen. Then press the number buttons (step 2) corresponding to the channel. Channel 12 can be entered as “1,” then by “2,” or as “0,” “1,” and “2.” Or press the up and down arrows to quickly step through each channel. When you find one you like, press the “select” button.
Listening to XM 12 Searching for channels by category XM channels are arranged by categories, or neighborhoods. This allows you to see all channels in the “Rock” category, for example. Press the “menu” button (step 1), go to “Search Mode,” and select “By Category.” Each press of the “search” button (step 2) tunes you to the first channel of a new category. Notice that the icon is highlighted in the display. Use the arrow buttons (step 3) to sample the channels within a category.
Searching for channels by scanning Your roadyXT can also scan through each channel, pausing long enough to hear the programming before moving on to the next one. Press the “menu” button (step 1), go to “Search Mode,” and select “By Scanning” (step 2). Press the “search” button to begin scanning (step 3). Each channel plays for about 5 seconds. While scanning channels, blinks in the display. Press the “search” button again to stop on a channel.
Listening to XM 14 Using presets Your roadyXT can store up to 30 of your favorite channels as presets. The presets are organized into three banks (A, B, or C) that each contain 10 presets. Press the “pre/dir” button one or more times to select bank A, B, or C (step 1). After you’ve tuned to your desired channel, press and hold a number button to save the channel into that preset (step 2). Whenever you want to quickly tune to that channel, simply press that button again.
Memory and jump Press the “memory” button to remember a song’s artist or title. Your roadyXT can remember up to 20 entries. (After 20, any new entry replaces the oldest entry in memory.) To recall the list of songs, press and hold the “memory” button, then use the up and down arrow buttons to step through the list. Press the “jump” button to return to the previous channel you were listening to. You can press and hold the “jump” button for FM presets. See page 16 for more information.
Personalizing Your roadyXT 16 Personalizing Your roadyXT You can easily adapt your roadyXT to suit your listening habits. Simply press the “menu” button to see the options you can customize. If you ever get lost or decide not to change anything, press the “menu” button several times to return to normal operation. Or just wait about 15 seconds and roadyXT automatically cancels whatever you’re doing.
Screen color To change the color of the display, press the “menu” button and select “Screen Color.” Use the arrow and the “select” buttons to choose a color; to cancel, press the “menu” button. Contrast To vary the contrast of the display, press the “menu” button and select “Contrast.” Use the arrow buttons to adjust the contrast, and press the “select” button to confirm. Audio level You may adjust roadyXT’s audio output level if it is too high (causing distortion) or too low.
Personalizing Your roadyXT 18 Aiming the antenna Note: For use with the Home Kit, sold separately. Your roadyXT can help you choose the best antenna position and orientation. 1. Press the “menu” button. Use the arrow and “select” buttons to choose “Antenna Aiming.” 2. Slowly turn and tilt the antenna. The signal bars on the display will change. Find the position that gives at least two bars on either “satellite” or “terrestrial.” 3.
Stock Ticker You can track up to 20 stock symbols and see their prices and movements right on the roadyXT’s display.* TO ADD A STOCK SYMBOL: 1. Press the “menu” button, select “Stock Ticker,” and select “Add Stocks.” 2. Use the arrow buttons to add each letter of the desired stock symbol. Press the “select” button after choosing each letter. (Your roadyXT has a list of more than 9,000 stock symbols, and will not only help you complete each entry but prevents you from entering incorrect symbols.) 3.
Personalizing Your roadyXT 20 Info Extras XM Satellite Radio will broadcast information such as sports scores and other features at various times.* Press the “menu” button and select “Info Extras” (step 1). Use the arrow buttons to see what’s available (step 2). Press the “select” button to add or remove the Info Extras item (step 3). “-” indicates that you have not yet selected the item; “+” means you’ve chosen the item.
Changing display information The Stock Ticker and Info Extras can either be scrolled (moving from right to left in the display) or paged (one symbol at a time). To switch from one option to the other: 1. Press the “menu” button and select “Display Mode.” 2. Choose either “Pages” or “Scroll.” Press the “select” button to confirm. Direct Tune Normally as you press the arrow buttons, you can preview what’s playing on other XM channels before actually selecting a channel.
Personalizing Your roadyXT 22 Auto-Off and “sleep” timer You can set your roadyXT to shut off the radio 1 to 3 hours after being turned on. Set this option if you have connected your roadyXT to a power source in your vehicle that is always live. Your roadyXT will then automatically shut off and prevent you from draining your vehicle’s battery. You can also use this feature as a “sleep” timer. 1. Press the “menu” button. 2. Select “Auto-Off.” 3. Select the desired time interval.
Other Things You Should Know Care You should be able to use your roadyXT during most of your daily activities. However, you should remember: • If your roadyXT does get dirty, wipe the case with a soft cloth (lightly moistened with water if necessary), then wipe dry with another cloth. Avoid chemicals such as paint thinner, alcohol, or abrasive cleansers. • It is best to keep your roadyXT out of direct sunlight or other sources of extreme heat. Caution: Refrain from using food or drinks near the roadyXT.
Other Things You Should Know 24 Troubleshooting Your roadyXT should provide you with trouble-free performance without needing any servicing. If it does not appear to be working properly, first try to remedy the problem by following these steps: 1. Attach all connections firmly and securely. 2. Ensure the cigarette lighter adaptor or auxiliary power socket is clean and free of corrosion. 3. Check the adaptor fuse by unscrewing the ribbed end of the adaptor. If required, replace with a 2-amp fuse only.
If you see this on the display: You should: UPDATING Cause: Your roadyXT is being updated with the latest encryption code. Simply wait a few seconds until the update is done. --Cause: You may have tried to tune to a channel that you have blocked or that you cannot receive with your subscription package. To receive that channel, contact XM Satellite Radio at 1.800.967.2346.
Other Things You Should Know 26 If this happens: You should: The display is blank; nothing happens when you push the power button. Check the power connections to your roadyXT. You do not receive all XM channels you have subscribed to. Your roadyXT may not be activated. Contact XM Satellite Radio (see page 10). Audio sounds distorted when using the built-in FM transmitter. Reduce audio output level (see page 17). Audio is too soft when using the built-in FM transmitter.
If this happens: You should: Audio has static while listening through an FM radio. Change to another FM frequency (see page 16). If the problem persists and you are using the wireless FM transmitter in a vehicle, use the Delphi FM Direct Adaptor (model SA10112, sold separately). Audio on XM instant traffic and weather channels sounds different from other XM channels. Nothing is wrong with your roadyXT. These channels use a different audio technology than the other XM channels.
Other Things You Should Know 28 Contacting Technical Support For additional information in solving problems with your roadyXT, contact Delphi Technical Support at 1.877.GO DELPHI (1.877.463.3574), 8:00 a.m.— 8:00 p.m. Eastern Time, Monday — Friday. Technical Support is also available at www.delphi.com. Technical Information DIMENSIONS receiver, without cradle: 2.25 in (H) x 3.7 in (W) x 0.7 in (D) 5.7 cm (H) x 9.4 cm (W) x 1.8 cm (D) remote: 3.7 in (H) x 1.7 in (W) x 0.6 in (D) 9.4 cm (H) x 4.
Warranty Delphi Limited Consumer Warranty Delphi Product and Service Solutions (“Delphi”) warrants all XM Satellite Radio Products sold by Delphi (each “Product”) to be free of defects in material and workmanship, subject to the following conditions: The duration of Delphi’s warranty with respect to each Product is limited to one (1) year from the date of sale to the original consumer purchaser. No other express warranties are made with respect to any Product.
Warranty 30 (iii) alteration or modification of a Product, (iv) misuse, (v) neglect, (vi) abuse, (vii) accident, (viii) normal wear and tear, (ix) commercial use, (x) improper storage, (xi) environmental conditions, including excessive temperature or humidity, (xii) service by anyone other than a Delphi authorized repair facility, (xiii) other improper application, installation or operation of this Product, or (xiv) defects or malfunctions of which Delphi is not advised within ten (10) days of the expirati
How you (the Customer) can get service To obtain warranty service during the first thirty (30) days after the date of purchase, you must return the defective Product with the original receipt to the original place of purchase. To obtain warranty service during the first thirty (30) days for Products purchased from www.delphi.com and for all Products for the remainder of the limited warranty period, you must contact Delphi by phone at 1.877.GO DELPHI (1.877.463.3574) or by fax at 1.866.790.3675.
Delphi Corporation 1441 West Long Lake Road Troy, Michigan 48098-5090 U.S.A. Customer Service: [1] 877.GO DELPHI www.delphi.com roadyXT, the XM name, TuneSelect, Roady2, and related logos are trademarks of XM Satellite Radio Inc. Printed on Recycled Paper ©2005 Delphi Corporation. All rights reserved.
Controhs power vehicle swivel mount !/ vehicle power adaptor roadyXT (i) r8CelVer 1'.1 DeeF' vehicle antenna CD Tr·.~ck$ 40 David Bowie surface preparation kit up and down arrows, select - change channels, choose menu options, TuneSelecC select .., --I----+_ "'-.........-........................I14-................iii;;;;,;;,................ ~- ~1.
Because every vehicle is different, we can only provide some general guidelines. If you need help, consult a professional installer. Use the CASSETIE ADAPTOR if your vehicle's audio system has a built-in cassette player. • Decide which method (cassette adaptor, wired connection, or wireless FM transmitter) is best for your vehicle and location.
We've included two types of mounts to help you install your roadyXT in your vehicle's interior. Turn off your roadyXT and your home stereo. Connect your roadyXT to your stereo as illustrated. Place the antenna on a window or an exterior wall that it points south. caution: Never use a commercial heat gun or paint-stripping gun. This could result in damage to the unit or to your vehicle. You can adjust the tension of the swivel mount by using a screwdriver. :::I:·j.:: i·!·l·!!:.\.·;!!:··!::::::::.::.:l.
(j) A. 111 dl~p C'" Radio 1D RBCD1234 0 9 roedyxt D€LPHI ~ select =, .. ; (i)! ~ ':'. ; i . menu . dlsp i c~~~~~~~
ro8dyXT, the XM name, TuneSelect, and related logos are trademarks ofXM Satellite Radio Inc ePrintedOn Recycled Paper C200S Delphi Corporation All rights reserved DPSS-QS-E-QS1
To activate your satellite radio, call the XM Listener Care Center at 1-800-XM-RADI0 (1-800-96'7-2346) or log on to: http://www.xmradio.
To purchase accessories for your Delphi satellite radio visit: http://www.shopdelphi.com ,...
DE~ADES LATIN 9O~ Q9()D~IQ 4 ..4<)~ BIG BAND/SWING/FORTIES 5 FIFTIES HITS 92 6 50s mill. SIXTIES HITS 94 ~ TROPICAL 7 ~ SEVENTIES HITS 95 ~ LATIN JAZZ 8 nlBOs EIGHTIES HITS WORLD 9 .,·9Os NINETIES HITS 100 CLASSIC COUNTRY joint 102 Nam.
Vehicle Installation Guidelines for XM Satellite Radio This XM Receiver offers the listener a variety of options for connecting XM Satellite Radio to your vehicle's FM radio. XM research and lab test results show that using a vehicle cassette adapter can best maximize the relationship between the best sound quality and ease of installation. If your vehicle kit does not include a cassette adapter, one should be available at your local retailer or visit www.xmradio.com.click ..Shop XM Radio.
Fig 1 Keep excess cable behind or under the dashboard • For best FM Modulator performance, you must locate the satellite radio antenna in a location that is in close proximity to the vehicle's FM antenna. • Avoid kinking, crimping, twisting or chafing the cable. Use pre-existing wire channels when possible. • For option 1 and rear mounting locations, route the cable into the trunk as shown. Always cross the weather seal at the lowest part of the trunk to reduce water leaks.
Once you have plugged the power and antenna jacks in to the car cradle, use the included cable organizer as shown in figure 3 to improve the overall appearance of the installation. Re-use the cable twist ties that were provided with the power adaptor and car antenna cables and always be sure to gather, bundle, twist tie, and secure any excess cable remaining after determining the best location for your satellite radio installation.
= IMPORTANT A . . INSTALLATION NOTICE In order to ensure that your new XM Radio operates properly you must install these attached "ferrites" to both the XM Satellite Radio antenna lead and the cigarette lighter adaptor lead as illustrated below. Doing so is an important part of the installation which is required to make sure that your XM Radio will not interfere with other radios. How to attach the snap on "ferrite" to the XM Satellite Radio POWER ADAPTER cable.
How to attach the snap on "ferrite"to the XM Satellite Radio antenna cable. ,0 loop 1 f1\ Place the XM car antenna ' 0 cable into the ferrite. h\2 Wrap the antenna cable \V around the ferrite once. CD f4\ Snap the ferrite closed. f5\ The cable should fit \.::..J tight against the f6\ \.::!./ \:::.J Be sure you are not pinching the cable. ferrite. Wrap the antenna cable around the ferrite a second time as shown. This is how the ferrite will look if you have attached it correctly.
DELPHI Expand Your Po 55 ibiii tie 5. . . Additional Roady XT Vehicle Kit Roady XT Home Kit IiiiI (SA10l?6 J (SA10l?8) Conveniently add Roady XT to a home or Conveniently add Roady XT to a second office environment with the Roady XT vehicle with this additional Roady XT Home Kit. Vehicle Kit. For Special Offers & Discounts, visit www.delphioffer.com/roadyxt3 For additional information on these exciting accessories check your local retailer or visit www.shopdelphi.com.
